ZI-ASA550E - Vacuum Cleaner Zipper - Free user manual and instructions

Product Type	Upright Vacuum Cleaner
Brand	Zipper
Model	ZI-ASA550E
Dimensions (H x W x D)	42 x 12 x 10 inches
Weight	14.5 lbs
Power Consumption	1200 W
Power Cord Length	25 ft
Dust Capacity	1.5 L (bagless)
Filtration	HEPA washable filter
Noise Level	75 dB(A)
Main Functions	Cyclonic suction, carpet & hard floor cleaning, edge cleaning
Attachments Included	Crevice tool, dusting brush, upholstery tool
Cleaning Path Width	12 inches
Suction Control	Variable suction via handle slider
Dust Cup Emptying	One-touch bottom release
Filter Maintenance	Washable HEPA filter; clean every 3 months
Overheat Protection	Automatic shut-off if motor overheats
Certification	CE, RoHS compliant
Warranty	2 years limited warranty
Spare Parts Availability	Filters, belts, and attachments available online

Frequently Asked Questions - ZI-ASA550E Zipper

How do I empty the dust cup?

Press the release button at the bottom of the dust cup and pull it away from the unit. Hold it over a trash bin and press the bottom release lever to empty. Avoid inhaling dust. For detailed steps, refer to the Dust Cup Emptying section in the manual.

How often should I clean the HEPA filter?

Clean the HEPA filter every 3 months under normal use. Remove the filter, tap off loose dust, and rinse under cold water until the water runs clear. Allow it to air-dry completely (at least 24 hours) before reinstalling. Do not use detergents or heat drying.

The vacuum has lost suction power. What should I do?

First, check if the dust cup is full and empty it if needed. Next, inspect the filters for clogs and clean or replace them. Also, examine the hose and nozzle for blockages. If the problem persists, the belt may be worn out; refer to the Troubleshooting section.

Can I use the vacuum on hardwood floors?

Yes, the ZI-ASA550E is designed for both carpets and hard floors. For hard floors, set the suction control to a lower setting (if adjustable) and ensure the brush roll is turned off or use the hard floor attachment if provided. Avoid using the brush roll on delicate surfaces.

How do I replace the brush roll belt?

Unplug the vacuum. Remove the bottom plate by unscrewing the screws. Detach the old belt from the motor shaft and brush roll. Install the new belt around the brush roll and then loop it over the motor shaft. Rotate the brush roll manually to ensure proper alignment. Replace the bottom plate and screws. See the Belt Replacement section for diagrams.

The vacuum turns off by itself during use. Why?

This is likely due to the overheat protection feature. The vacuum shuts off automatically if the motor temperature gets too high. Check if the dust cup is full or filters are clogged, which restricts airflow. Allow the vacuum to cool down for about 30 minutes before restarting. Ensure the vacuum is not used on thick carpets for extended periods.

What attachments are included with the vacuum?

The ZI-ASA550E comes with a crevice tool, a dusting brush, and an upholstery tool. These can be used for cleaning corners, delicate surfaces, and furniture. Attach them directly to the handle or extension wand.

Is the vacuum bagless? How do I dispose of the dust?

Yes, it's a bagless model with a 1.5L dust cup. To dispose of dust, empty the cup into a trash bin. For fine dust, it's advisable to wear a mask. The cup can be rinsed with water occasionally for deeper cleaning—ensure it's completely dry before reinserting.

Where can I find spare parts or accessories?

Spare parts such as filters, belts, and attachments are available on the Zipper website or authorized online retailers. Use the model number ZI-ASA550E to ensure compatibility. For warranty-related replacements, contact Zipper customer support.

How do I store the vacuum?

Wrap the power cord around the cord hooks on the back of the vacuum. Stand it upright in a dry, cool place. Avoid leaning it against walls or furniture to prevent damage. If using for extended periods, store with the dust cup empty and filters clean.

USER MANUAL ZI-ASA550E Zipper

Green and black industrial machine with a white spray bag and coiled tubing (no visible text or symbols)

CE

ZI-ASA550E

EAN: 9120039233611

1 INHALT / INDEX

1 INHALT / INDEX 2

12.1 Intended Use....19

12.2 Security instructions .... 19

12.3 Remaining risk factors....21

13 ASSEMBLY 21

13.1 Delivery content 21

13.2 Workplace requirements 21

13.3 Power supply 21

13.4 Assembly (Fig. 1-11) 22

14 OPERATION 22

14.1 Operation instructions....22

14.2 Connection of dust collector to machine 23

14.3 Switch unit 23

14.4 Switching on....23

14.5 Switching off 23

14.6 Emptying the debris bags 23

15 MAINTENANCE 24

15.1 Maintenance plan 24

15.1.1 Change of dust collector bag.... 24

15.2 Cleaning 25

15.3 Disposal....25

16 TROUBLE SHOOTING 25

17 PŘEDMLUVA (CZ) 26

18 POUZITI 27

EN EC-CONFORM - This product complies with the EC-directives.

EN READ THE MANUAL! Read the user and maintenance manual carefully and get familiar with the controls in order to use the machine correctly and to avoid injuries and machine defects.

EN ATTENTION! Ignoring the safety signs and warnings applied on the machine as well as ignoring the security and operating instructions can cause serious injuries and even lead to death.

EN Protective clothing!

EN Stop and pull out the power plug before any break and engine maintenance!

EN Warning of rotating parts!

EN Protect from moisture!

EN Highly flammable!

CZ Vysoce hořlavý!

SL Lahko vnetljivo!

HR Vrlo zapaljivo!

EN Hand injuries because of belt drive!

3 ILLUSTRATIONEN ZUSAMMENBAU / ILLUSTRATION ASSEMBLY

4 TECHNIK / TECHNIC

4.1 Komponenten / components

Illustration
1	KunststoffgehäusePlastic housingPlastový krytPlastično ohišjePlastično kućište	8	StaubsackDust bagPrachový vakVreča za prahVreća za prašinu
2	SeitenblecheSide panelsBoční plechyBoční pločevinski deliBoční limovi	9	Schnellspannvorrichtung SpänesackQuick clamp device for PVC debris collector bagRychloupínák vaku hoblinNaprava za hitro vpenjanje vreče za žagovinoNaprava za brzo stezanje vreće za piljevinu
3	FahrgestellrahmenChassis frameRám podvozkuPodstavekPostolje	10	Schnellspannvorrichtung FiltersackQuick clamp device for dust bagRychloupínák vaku filtruNaprava za hitro vpenjanje filter vrečeNaprava za brzo stezanje vreće za prašinu
4	MotorMotorMotorMotorMotor	11	Haltevorrichtung StaubsackHolding device for dust bagDržák vakuPrijemalna naprava za vrečo za prahNaprava za učvršćivanje vreće za prašinu
5	Ein-, AusschalterON/OFF switchVypínačStikalo za vklop in izklopSklopka za uključivanje / isključivanje	12	RäderWheelsKolaKolesaKotači
6	AbsaugschlauchExtractor hoseOdsávací hadiceSesalna cevUsisno crijevo	13	TransportgriffTransportation handleMadlo pro přepravuTransportna ročicaRučka za transport uređaja
7	PVC SpänefangsackPVC sawdust bagVak z PVC na hobliny (dřevěný odpad)PVC prestrezna vreča za žagovinoPVC vreća za sakupljanje piljevine	14	AdapterAdapterAdaptérAdapterAdapter

4.2 Lieferumfang / Delivery content

Bezeichnung / Name	Qty
Vormontierte Einheit / Pre-assembled device unit	1
Absaugschlauch / Extraction hose / Odsávací hadice /Sesalna cev /Usisno crijevo	1
Räder / Wheels / Kola / Kolesa /Kotača	2
Staubsack /dust bag / Prachový vak /Vreča za prah /Vreća za prašinu	1
Spänefangsack /Sawdust collecting bag / Vak z PVC na hobliny (dřevěný odpad) PVC prestrezna vreča za žagovino / PVC vreća za sakupljanje piljevine	5
Seitenblech /Side panel / Boční plechy /Bočni pločevinski deli / Bočni limovi (links/rechts; left/right; Levý/pravý; Levo/desno ; Lijevo/desno)	1+1
Querverbindung / Transverse joint	1
Rahmen / Base frame / Rám podvozku /Podstavek /Postolje	1
Schnellspanner / Quick release fasteners / Rychloupínák Naprava za hitro vpenjanje /Naprava za brzo stezanje	2
Aufhängung Staubsack / Bag suspension / Držák vaku /Prijemalna naprava za vrečo za prah /Naprava za učvršćivanje vreće za prašinu	1
Montagematerial /Screw bag	1
Bedienungsanleitung / Instruction manual / NÁVOD NA OBSLUHU / Navadila za uporabo / upute za uporabu	1
Adapter ø100-ø70; ø70-ø45; ø45-ø40; ø40-ø35	1+1+1+1

Close-up of a black industrial electrical switch with yellow and red buttons, mounted on a base with visible wiring (no text or symbols)

8.4 Einschalten

This manual contains important information and advice for the correct and safe use and maintenance of the dust collector ZI-ASA550E.

Following the usual commercial name of the device (see cover) is substituted in this manual with the name "machine".

The manual is part of the machine and may not be stored separately. Read it profoundly before first use of the machine and keep it for later reference. When the machine is handed to other persons always put the manual to the machine.

Please follow the security instructions!

Please read the entire manual, to prevent misunderstandings, machine damage or even injuries!

Due to continuous development of our products illustrations, pictures might differ slightly.

If you however find errors in this manual, please inform us.

Technical changes excepted!

Copyright law

© 2018

This manual is protected by copyright law – all rights reserved. Especially the reprinting as well as the translation and depiction of pictures will be prosecuted by law. Court of jurisdiction is the Landesgericht Linz or the competent court for 4707 Schlüsslberg, AUSTRIA.

Customer Support

The machine must only be used for its intended purpose! Any other use is deemed to be a case of misuse.

To use the machine properly you must also observe and follow all safety regulations, the assembly instructions, operating and maintenance instructions lay down in this manual.

All people who use and service the machine have to be acquainted with this manual and must be informed about the machine's potential hazards.

It is also imperative to observe the accident prevention regulations in force in your area.

The same applies for the general rules of occupational health and safety.

The machine is used for:

Extract of wood dust, wood and plastic chips.

Any manipulation of the machine or its parts is a misuse, in this case ZIPPER-MASCHINEN and its sales partners cannot be made liable for ANY direct or indirect damage.

Even when the machine is used as prescribed it is still impossible to eliminate certain residual risk factors.

WAR NI NG

• Inflammable gases (e.g. paint or varnish mist) must not be extracted.
• Polyethylene dust bags must be a minimum thickness of 0,2mm!
• When using bags made of other materials the mechanical strength must be the same!
• Refer the user manual of the connected woodworking machine!

Ambient conditions

The machine may be operated:

humidity

max. 70%

temperature

$$ + 5 ^ {\circ} \mathrm{C} \text { to } + 4 0 ^ {\circ} \mathrm{C} (+ 4 1 ^ {\circ} \mathrm{F} \text { to } + 1 0 4 ^ {\circ} \mathrm{F}) $$

The machine shall not be operated outdoors or in wet or damp areas.

The machine shall not be operated in areas exposed to increased fire or explosion hazard.

Prohibited use

• The operation of the machine outside the stated technical limits described in this manual is forbidden.
  • The use of the machine not according with the required dimensions is forbidden.
• The use of the machine not being suitable for the use of the machine and not being certified is forbidden.
  • Any manipulation of the machine and parts is forbidden.
• The use of the machine for any purposes other than described in this user-manual is forbidden.
  • The unattended operation on the machine during the working process is forbidden!
  • It is not allowed to leave the immediate work area during the work is being performed.

12.2 Security instructions

Missing or non-readable security stickers have to be replaced immediately!

The locally applicable laws and regulations may specify the minimum age of the operator and limit the use of this machine!

To avoid malfunction, machine defects and injuries, read the following security instructions!

• Keep your work area dry and tidy! An untidy work area may cause accidents. Avoid slippery floor.
• Make sure the work area is lighted sufficiently
• Do not overload the machine

• Always stay focused when working. Reduce distortion sources in your working environment. The operation of the machine when being tired, as well as under the influence of alcohol, drugs or concentration influencing medicaments is forbidden.
  • Work in a well ventilated area!

• Respectively trained people only and only one person shall operate the machine.

• Do not allow other people, particularly children, to touch the machine or the cable. Keep them away from your work area.
  • Make your workshop childproof.
• Make sure there is nobody present in the dangerous area. The minimum safety distance is 2m

• Wear suitable work clothes! Do not wear loose clothing or jewelry as they might be caught and cause severe accidents!
• Wear a hair net if you have long hair.
• Loose objects can become entangled and cause serious injuries!

- Use personal safety equipment: dust mask, ear protectors and safety goggles when working with the machine.

• Never leave the machine running unattended! Before leaving the working area switch the machine off and wait until the machine stops.
• Always disconnect the machine prior to any actions performed at the machine.
• Avoid unintentional starting
• Do not use the machine with damaged switch

• The plug of an electrical tool must strictly correspond to the socket. Do not use any adapters together with earthed electric tools
  • Each time you work with an electrically operated machine, caution is advised! There is a risk of electric shock, fire, cutting injury;
• Protect the machine from dampness (causing a short circuit)
• Use power tools and machines never in the vicinity of flammable liquids and gases (danger of explosion)
• Check the cable regularly for damage
• When working with the machine outdoors, use extension cables suitable for outdoor use
• Do not use the cable to carry the machine
• Protect the cable from heat, oil and sharp edges
• Avoid body contact with earthed
• FIRE HAZARD:

Especially the aspiration of lightly flammable materials like gases, liquids, metal dust or chippings, solvents, hot ashes, cigarette waste ... is strictly forbidden!

• Do not insert any objections into the dust collector hood and keep hand away from the dust collector hood when machine is connected to power supply.
• Regularly check the dust collector hood for debris and clean it if necessary.
• Do not dismount the protective fence in the dust collector hood. It is a security component and must be left in place.

12.3 Remaining risk factors

Despite of correct and proper use and maintenance there remain some residual risk factors:

• Hazard of injury or machine damage due to undetected machine defect

To minimize this risk, check the machine prior to every operation for loose screws and connections. Check the motor noise, the collector tubes, filter bag, dust collector bag and impeller for eventual damage. Damaged parts have to be replaced immediately, no operation of the machine in the meantime!

• Hazard of electric shock

Undetected malfunctions in the power supply and/or the connected wood working machine might result in electric shock when touching the machine. Ensure proper electric installation, and let it check periodically by a trained electrician.

• Danger due to unintended machine start-up

Eliminate this risk by disconnecting the machine before you perform any checks or activities on the machine.

• Hazard of inhaling toxic wood dust

Especially wood dust arising from chemically treated wood and/or lacquer/paint are harmful when inhaled. Therefore let the dust settle for 10 Minutes before you change the dust collector bag and wear a suitable breathing mask if required.

13 ASSEMBLY

13.1 Delivery content

Please check the product contents immediately after receipt for any eventual transport damage or missing parts. Claims from transport damage or missing parts must be placed immediately after initial machine receipt and unpacking before putting the machine into operation. Please understand that later claims cannot be accepted anymore.

13.2 Workplace requirements

The workplace has to fulfill the requirements.

The ground has to be even, in level and hard. It must be suitable at least to weight it with double weight per square meter than the machines net weight.

The chosen workplace must have access to a suitable electric supply net hat complies with the machines requirements.

13.3 Power supply

ATTENTI ON

When working with non-grounded machines: Severe injury or even death may arise though electrocution!

Therefore: The machine must be operated at a grounded power socket

The connection of the machine to the electric power supply and the following checks have to be carried out by a respectively trained electrician only.

1. The electronic connection of the machine is designated for operation with a grounded power socket!

2. The connector plug may not be manipulated.

3. The mains supply must be secured with 10A:

4. If the connector plug doesn't fit or if it is defect, only qualified electricians may modify or re-new it!

5. The grounding wire should be held in green-yellow.

6. A damaged cable has to be exchanged immediately!

7. Make sure that a possible extension cord is in good condition and suitable for the transmission of power. An undersized cord reduces the transmission of power and heats up.

8. A damaged cable must be replaced immediately

NOTICE

Operation is only allowed with safety switch against stray current (RCD max. stray current of 30mA)

NOT ICE

Use only permitted extension cable with cross-section the one in the following table declared.

Voltage	Extension	Cross-section
220 V-240 V50 Hz	<27 m	1,5 mm^2
	<44 m	2,5 mm^2
	<70 m	4,0 mm^2
	<105 m	6,0 mm^2

13.4 Assembly (Fig. 1-11)

Important! Pull out the power plug before carrying out any maintenance, resetting or assembly work on the vacuum extraction system!

• Fig1.: Screw on both side parts (1+2). For each side part you require 2 cup square screws M8x40 2 combi nuts M8
• Fig2.: Screw on the transverse joint (4) For the connection you require: 4 cup square screws M8x10, 4 combi nuts M8
• Fig3.: Put the pre-assembled device unit on the side parts.
• Fig4.: Fix first one side with each 2 round-head screws M5x16 and hexagon nut M5. Now fix the other side. Then, fasten the four screw connections.
• Fig5.: Put on the extraction hose (7). Fasten the extraction hose by refastening the screw on the hose clip (17) a few revolutions.
  • Fig6.: Put on the saw dust collection bag (14)
  • Fig7.: Fasten the saw dust collection bag by attaching the quick release fastener (6).
  • Fig8.: Hang in the bag suspension (9).
  • Fig9.: Put on the filter bag (15)
  • Fig10.: Fasten the filter bag by attaching the quick release fastener (6).
  • Fig11.: Hang in the filter bag.

14 OPERATION

Device to be operated in a perfect state only. Inspect the device visually every time it is to be used. Check in particular the safety equipment, electrical controls, electric cables and screwed connection for damage and if tightened properly. Replace any damaged parts before operating the device.

14.1 Operation instructions

WAR NING

Perform all machine settings with the machine being disconnected from the power supply!

HIN WEIS

• Place the machine next to the woodworking machine in a way that it will not interfere with your work!
• Start to work with the woodworking machine only until the dust collector has reached full speed!

14.2 Connection of dust collector to machine

Dust collector plug: ∅ 100mm

Ensure dust collector tubes to be composed of hardly inflammable material and antistatic.

The total distance between dust collector hood and machine dust collector hood shall not exceed 10 meters.

14.3 Switch unit

On-off-switch:

Press green button (I): turn on Press red button (O): turn off

Close-up of a black industrial electrical switch with yellow and red buttons, mounted on a black base (no visible text or symbols)

14.4 Switching on

• Check that extractor hose (6) is attached firmly to the adapter of both vacuum extractor and woodworking machine.
• Check if dust collecting bags (7/8) are tightened well.
• Start the dust collector by pressing the green button "I".
  • Now you can start the woodworking machine.

14.5 Switching off

• Switch off the woodworking machine
• Switch off the woodworking machine by pressing the red button,,0" or by pressing the Emergency button (17).

14.6 Emptying the debris bags

The debris collector bag (7) shall be controlled on a regularly basis and emptied if necessary. Empty bags when they are approximately 2/3 full.

• Attention: Disconnect from power supply!
• Shake the dust bag. Let the dust settle down for 5 minutes.
• Grap collector bag with left hand.
• Release the quick clamp (9)
  • Take the bag and dispose the content meeting environmental standards.
  • Fix the empty bag onto the holding device and fix it with the quick clamp (9).

15 MAINTENANCE

ATTENTI ON

Don't clean or do maintenance on the machine while it is still connected to the power supply:

Damages to machine and injuries might occur due to unintended switching on of the machine!

Therefore: Switch the machine off and disconnect it from the power supply be-fore any maintenance works or cleaning is carried out

The machine does not require extensive maintenance. If malfunctions and defects occur, let it be serviced by trained persons only.

Before first operation as well as later on every 100 operation hours you should lubricate all connecting parts (if required, remove beforehand with a brush all swarfs and dust).

Check regularly the condition of the security stickers. Replace them if required.

Check regularly the condition of the machine.

The good condition and perfect adjustment of the guiding rollers is essential for a smooth band guidance and a clean cut.

Store the machine in a closed, dry location.

NOTICE

Clean your machine regularly after every usage – it prolongs the machines lifespan and is a pre-requisite for a safe working environment.

Repair jobs shall be performed by respectively trained professionals only!

15.1 Maintenance plan

• Clean regularly the filter bag to ensure its filter capacity.
• You should check the dust collector hood regularly for deposits that cumulate especially on the protective fence and clean if necessary. Failure to do so will result in lower suction capacity and motor overload.
• Do not dismount the protective fence, it is a security component.

15.1.1 Change of dust collector bag

Empty dust collector bags when they are 60-70% full.

Switch the dust collector off and let the dust settle at least for 10 minutes.

Disconnect the dust collector from the power supply.

Do not use a dust collector bag twice.

Use solely certified dust collector bags, which match with the technical specifications, especially and height, of the dust collector

15.2 Cleaning

After each workshift the machine has to be cleaned. Remove chips etc. with a suitable tool. Do not remove them by hand (cutting injury!). Remove dust as well.

NOTICE

The usage of certain solutions containing ingredients damaging metal surfaces as well as the use of scrubbing agents will damage the machine surface!

Clean the machine surface with a wet cloth soaked in a mild solution

15.3 Disposal

Do not dispose the machine in residual waste. Contact your local authorities for information regarding the available disposal options. When you buy at your local dealer for a replacement unit, the latter is obliged to exchange your old.

16 TROUBLE SHOOTING

BEFORE YOU START WORKING FOR THE ELIMINATION OF DEFECTS, DISCONNECT THE MACHINE FROM THE POWER SUPPLY.

Trouble	Possible cause	Solution
The magnetic support has no magnetic force	Switch defective	Repair switch
	Power supply is off	Repair power supply
	Fuse is defectivet	Change fuse
	Electric contactor is defective	Repair or change electric contactor
Dust emerges from	Leaking or blocked connections	Check connectionRemove blockages
	Dust bag or filter bag is defective or incorrectly installed	Check bagsChange defective bags
Loud noise in the fan wheel housing	Extracting of a big part	Switch of the machine, disconnect the machine and remove the part
	Loosen fan wheel	Tighten the fan wheel

MANY POTENTIAL SOURCES OF ERROR CAN BE CLEARED BY THE EXPERTLY CONNECTION TO THE ELECTRICITY GRID.

NOT ICE

Should you in necessary repairs not able to properly to perform or you have not the prescribed training for it always attract a workshop to fix the problem.

17 PŘEDMLUVA (CZ)

Vážený zákazníku!

With original ZIPPER spare parts you use parts that are attuned to each other shorten the installation time and elongate your machines lifespan.

IMP OR TAN T

The installation of other than original spare parts voids the warranty!

So you always have to use original spare parts

When you place a spare parts order please use the service formular you can find in the last chapter of this manual. Always take a note of the machine type, spare parts number and partname. We recommend to copy the spare parts diagram and mark the spare part you need.

You find the order address in the preface of this operation manual.

Pos.	Description
1	Side part - left
2	Side part - right
3	Base frame with wheels and bottom plate
4	Transverse joint
5	Wheel
6	Quick release fastener for filter or saw dust bag
7	Extraction hose
8	Fan wheel with fastening
9	Bag suspension
10	Handhold
11	Motor with switch
12	Switch
13	Synthetic cabinet kpl.
14	Saw dust collecting bag
15	Filter bag
16	Hose clip

43 EG-KONFORMITÄTSERKLÄRUNG / CE-DECLARATION OF CONFORMITY / POTVRDA O SUKLADNOSTI

Inverkehrbringer / Distributor

Hereby we declare that the above mentioned machines meet the essential safety and health requirements of the above stated EC directives. Any manipulation or change of the machine not being explicitly authorized by us in advance renders this document null and void.

Company ZIPPER Maschinen GmbH grants for mechanical and electrical components a warranty period of 2 years for amateur use; and warranty period of 1 year for professional use, starting with the purchase of the final consumer. In case of defects during this period, which are not excluded by paragraph 3, ZIPPER will repair or replace the machine at its own discretion.

2.) Report:

In order to check the legitimacy of warranty claims, the final consumer must contact his dealer. The dealer has to report in written form the occurred defect to ZIPPER. If the warranty claim is legitimate, ZIPPER will pick up the defective machine from the dealer. Returned shippings by dealers which have not been coordinated with ZIPPER, will not be accepted and refused.

3.) Regulations:

a) Warranty claims will only be accepted, when a copy of the original invoice or cash voucher from the trading partner of ZIPPER is enclosed to the machine. The warranty claim expires if the accessories belonging to the machine are missing.
b) The warranty does not include free checking, maintenance, inspection or service works on the machine. Defects due to incorrect usage of the final consumer or his dealer will not be accepted as warranty claims either. Some examples: usage of wrong fuel, frost damages in water tanks, leaving fuel in the tank during the winter, etc.
c) Defects on wear parts are excluded, e.g. carbon brushes, collection bags, knives, cylinders, cutting blades, clutches, sealings, wheels, saw blades, splitting crosses, riving knives, riving knife extensions, hydraulic oils, oil/air/fuel filters, chains, spark plugs, sliding blocks, etc.
d) Also excluded are damages on the machine caused by incorrect or inappropriate usage, if it was used for a purpose which the machine is not supposed to, ignoring the user manual, force majeure, repairs or technical manipulations by not authorized workshops or by the customer himself, usage of non-original ZIPPER spare parts or accessories.
e) After inspection by our qualified personnel, resulted costs (like freight charges) and expenses for not legitimated warranty claims will be charged to the final customer or dealer.
f) In case of defective machines outside the warranty period, we will only repair after advance payment or dealer's invoice according to the cost estimate (incl. freight costs) of ZIPPER.
g) Warranty claims can only be granted for customers of an authorized ZIPPER dealer who directly purchased the machine from ZIPPER. These claims are not transferable in case of multiple sales of the machine.

4.) Claims for compensation and other liabilities:

The liability of company ZIPPER is limited to the value of goods in all cases. Claims for compensation because of poor performance, lacks, damages or loss of earnings due to defects during the warranty period will not be accepted. ZIPPER insists on its right to subsequent improvement of the machine.

46 ZÁRUKA (CZ)

1.) Záruka:

Product experience form

We observe the quality of our delivered products in the frame of a Quality Management policy. Your opinion is essential for further product development and product choice. Please let us know about your:

• Impressions and suggestions for improvement.
• experiences that may be useful for other users and for product design
• Experiences with malfunctions that occur in specific operation modes

We would like to ask you to note down your experiences and observations and send them to us via FAX, E-Mail or by post:

Name / name:
Produkt / product:
Kaufdatum / purchase date:
Erworben von / purchased from:
E-Mail/ e-mail: 

Please describe amongst others in the problem: What has cause the problem/defect, what was the last activity before you noticed the problem/defect? For electrical problems: Have you had checked you electric supply and the machine already by a certified electrician?

3. Bitte beachten

/ Additional information

INCOMPLETELY FILLED SERVICE FORMS CANNOT BE PROCESSED! FOR GUARANTEE CLAIMS PLEASE ADD A COPY OF YOUR ORIGINAL SALES / DELIVERY RECEIPT OTHERWISE IT CANNOT BE ACCEPTED. FOR SPARE PART ORDERS PLEASE ADD TO THIS SERVICE FORM A COPY OF THE