WHT68AINB - Range hood GORENJE - Free user manual and instructions

Product Type	Wall-mounted range hood
Brand	Gorenje
Model	WHT68AINB
Control Type	Mechanical knob with electronic assembly
Number of Speeds	4 (1, 2, 3, Boost)
Boost Function	Yes, 5-minute intensive speed
Automatic Mode	Yes, adjusts motor speed based on cooking conditions
Lighting	Halogen GU10 bulbs
Filter Type	Grease filter (washable), optional charcoal filter for recirculation
Installation Modes	Ducting (exhaust) or recirculation (filter)
Minimum Distance from Hob	50 cm (electric), 65 cm (gas or mixed)
Electrical Connection	230 V ~ 50 Hz (see rating plate)
Power Consumption	Refer to rating plate inside hood
Weight	Approx. 15 kg (estimated)
Dimensions (W×D×H)	Approx. 68 cm × 50 cm × 30 cm (estimated)
Material	Stainless steel (typical)
Grease Filter Cleaning	Monthly, by hand or dishwasher (low temperature, short cycle)
Charcoal Filter Replacement	As needed for recirculation mode
Safety Features	Disconnect power before maintenance, auto-return knob, overheating protection
Certifications	CE, WEEE (2002/96/EC)
Spare Parts	Grease filter, charcoal filter, halogen bulbs (GU10)
Noise Level	Approx. 55 dB (estimated)

Frequently Asked Questions - WHT68AINB GORENJE

What is the minimum distance between the hob and the range hood?

The minimum distance is 50 cm for electric cookers and 65 cm for gas or mixed cookers. Follow the gas hob installation instructions if a greater distance is specified.

How do I clean the grease filter?

Clean the grease filter once a month using non-aggressive detergents, either by hand or in the dishwasher on a low temperature, short cycle. The filter may discolor slightly in the dishwasher, but this does not affect its filtering capacity.

How do I replace the light bulbs?

Disconnect the hood from power, ensure bulbs are cool, and replace burned-out bulbs with GU10 halogen bulbs only. After replacement, clean the lens.

What are the speed settings and how do I use the boost function?

The hood has 4 speeds (1, 2, 3, Boost). Turn the knob clockwise from 0 to 1, then to 2, 3, and P for boost. Boost runs for 5 minutes then returns to speed 3. The knob has an auto-return function in boost position.

How do I activate the automatic mode?

Turn the knob anti-clockwise from 0 to position A. The hood will automatically adjust motor speed based on cooking conditions. The knob returns to 0 when released. A white light indicator shows when automatic mode is active.

Can I use the hood with an existing ventilation system?

No, the ducting system must not be connected to any existing ventilation system used for other purposes, such as exhausting fumes from gas or other fuel-burning appliances.

What should I do if the hood does not work?

Check the power supply and that the plug is connected. If the lights do not work, ensure bulbs are properly fitted. If problems persist, contact Technical Service.

How often should I replace the charcoal filter?

The charcoal filter is needed only for recirculation mode. Replace it when it becomes saturated, typically every 3-6 months depending on usage.

Is the hood suitable for use over a gas hob?

Yes, but ensure a minimum distance of 65 cm from the hob surface. The room must be well ventilated if the hood is used with gas or other fuel-burning devices.

What maintenance is required for the hood?

Clean the hood externally and internally at least once a month using a damp cloth with neutral liquid detergent. Do not use abrasive products or alcohol. Clean the grease filter monthly and replace charcoal filters as needed.

USER MANUAL WHT68AINB GORENJE

Product catalog image showing various kitchen appliances including oven, microwave, and air conditioner (no visible text or labels)

Diagram of a mechanical or structural assembly with directional arrows and a house icon (no text or symbols)

Technical diagram of a mechanical or structural assembly with directional arrows indicating movement or force (no text or symbols present)

1

Technical line drawing showing a kitchen appliance with a door, a stove, and a hand holding a tool (no text or symbols)

Technical line drawing of a ductwork assembly with a pipe and housing, showing airflow direction (no text or symbols)

Isometric line drawing of a mechanical component with labeled parts 14 and 15, showing internal structure and base (no text or symbols beyond labels)

Diagram showing three steps of installing a solar panel layout, with no text or symbols present.

Closely follow the instructions set out in this manual. All responsibility, for any eventual inconveniences, damages or fires caused by not complying with the instructions in this manual, is declined. The extractor hood has been designed exclusively for domestic use.

The hood can look different to that illustrated in the drawings in this booklet. The instructions for use, maintenance and installation, however, remain the same.

It is important to conserve this booklet for consultation at any moment. In the case of sale, cession or move, make sure it is together with the product.

! Read the instructions carefully: there is important information about installation, use and safety.

! Do not carry out electrical or mechanical variations on the product or on the discharge conduits.

Note: the elements marked with the symbol “(*)” are optional accessories supplied only with some models or elements to purchase, not supplied.

Caution

WARNING! Do not connect the appliance to the mains until the installation is fully complete.

Before any cleaning or maintenance operation, disconnect hood from the mains by removing the plug or disconnecting the mains electrical supply.

Always wear work gloves for all installation and maintenance operations.

The appliance is not intended for use by children or persons with impaired physical, sensorial or mental faculties, or if lacking in experience or knowledge, unless they are under supervision or have been trained in the use of the appliance by a person responsible for their safety.

This appliance is designed to be operated by adults, children should be monitored to ensure that they do not play with the appliance.

This appliance is designed to be operated by adults. Children should not be allowed to tamper with the controls or play with the appliance.

Never use the hood without effectively mounted grating!

The hood must NEVER be used as a support surface unless specifically indicated.

The premises where the appliance is installed must be sufficiently ventilated, when the kitchen hood is used together with other gas combustion devices or other fuels.

The ducting system for this appliance must not be connected to any existing ventilation system which is being used for any other purpose such as discharging exhaust fumes from appliances burning gas or other fuels.

The flaming of foods beneath the hood itself is severely prohibited.

The use of exposed flames is detrimental to the filters and may cause a fire risk, and must therefore be avoided in all circumstances.

Any frying must be done with care in order to make sure that the oil does not overheat and ignite.

Accessible parts of the hood may become hot when used with cooking appliance.

With regards to the technical and safety measures to be adopted for fume discharging it is important to closely follow the regulations provided by the local authorities.

The hood must be regularly cleaned on both the inside and outside (AT LEAST ONCE A MONTH).

This must be completed in accordance with the maintenance instructions provided in this manual). Failure to follow the instructions provided in this user guide regarding the cleaning of the hood and filters will lead to the risk of fires.

Do not use or leave the hood without the lamp correctly mounted due to the possible risk of electric shocks.

We will not accept any responsibility for any faults, damage or fires caused to the appliance as a result of the non-observance of the instructions included in this manual.

This appliance is marked according to the European directive

2002/96/EC on Waste Electrical and Electronic Equipment (WEEE). By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.

The symbol 📄 on the product, or on the documents accompanying the product, indicates that this appliance may not be treated as household waste. Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment. Disposal must be carried out in accordance with local environmental regulations for waste disposal. For further detailed information regarding the process, collection and recycling of this product, please contact the appropriate department of your local authorities or the local department for household waste or the shop where you purchased this product.

Use

The hood is designed to be used either for exhausting or filter version.

The models with no suction motor only operate in ducting mode, and must be connected to an external suction device (not supplied).

The connecting instructions are supplied with the peripheral suction unit.

Ducting version

In this case the fumes are conveyed outside of the building by means of a special pipe connected with the connection ring located on top of the hood.

Attention! The exhausting pipe is not supplied and must be purchased apart.

Diameter of the exhausting pipe must be equal to that of the connection ring.

In the horizontal runs the exhausting pipe must be slightly slanted (about 10^ ) and directed upwards to vent the air easily from the room to the outside.

Attention! If the hood is supplied with active charcoal filter, then it must be removed.

Connect the hood and discharge holes on the walls with a diameter equivalent to the air outlet (connection flange).

Using the tubes and discharge holes on walls with smaller dimensions will cause a diminution of the suction performance and a drastic increase in noise.

Any responsibility in the matter is therefore declined.

! Use a duct of the minimum indispensable length.

! Use a duct with as few elbows as possible (maximum elbow angle: 90°).

! Avoid drastic changes in the duct cross-section.

! Use a duct with an as smooth as possible inside.

! The duct must be made of certified material.

Filter version

One active charcoal filter is needed for this and can be obtained from your usual retailer.

The filter removes the grease and smells from the extracted air before sending it back into the room through the upper outlet grid.

Installation

The minimum distance between the supporting surface for the cooking equipment on the hob and the lowest part of the range hood must be not less than 50cm from electric cookers and 65cm from gas or mixed cookers.

If the instructions for installation for the gas hob specify a greater distance, this must be adhered to.

Electrical connection

The mains power supply must correspond to the rating indicated on the plate situated inside the hood. If provided with a plug connect the hood to a socket in compliance with current regulations and positioned in an accessible area, after installation. If it not fitted with a plug (direct mains connection) or if the plug is not located in an accessible area, after installation, apply a double pole switch in accordance with standards which assures the complete disconnection of the mains under conditions relating to over-current category III, in accordance with installation instructions.

Warning! Before re-connecting the hood circuit to the mains supply and checking the efficient function, always check that the mains cable is correctly assembled.

The hood is provided with a special power cable ; if the cable is damaged, request a new one from Technical Service.

Mounting

Expansion wall plugs are provided to secure the hood to most types of walls/ceilings. However, a qualified technician must verify suitability of the materials in accordance with the type of wall/ceiling. The wall/ceiling must be strong enough to take the weight of the hood. Do not tile, grout or silicone this appliance to the wall. Surface mounting only.

Operation

Use the high suction speed in cases of concentrated kitchen vapours. It is recommended that the cooker hood suction is switched on for 5 minutes prior to cooking and to leave in operation during cooking and for another 15 minutes approximately after terminating cooking.

WHT68INI, WHT68INB

1 ON/OFF lights

2 ON / OFF motor / Speed Increase

Turning the knob into position "0" during functioning, the hood turns OFF.

Turning the knob from position "0" into position "1" hood passes from the OFF state to speed 1.

Turning the knob in right direction (hood in ON state) the motor speed is increased from speed 1 to intensive

Speed 1:1

Speed 2: 2

Speed 3:3

WHT68AINI, WHT68AINB

1. Mechanical control cooperates with the electronics assembly – it serves only as a control panel. The electronics assembly is responsible for activation of the motor's power supply.
2. By turning the wing knob clockwise from position 0 to position 1, the motor goes into first gear and stays in first gear until this position is altered manually. Reverse action reverts the settings to their previous state – gear 0.
3. By turning the wing knob clockwise from position 1 to position 2, the motor goes into second gear and stays in second gear until this position is altered manually. Reverse action reverts the settings to their previous state – gear 1.
4. By turning the wing knob clockwise from position 2 to position 3, the motor goes into third gear and stays in third gear until this position is altered manually. Reverse action reverts the settings to their previous state – gear 2.
5. By turning the wing knob clockwise from position 3 to position P, the motor goes into fourth gear and stays in fourth gear for five minutes, unless this position is altered manually within that time. Once 5 minutes passes, the motor returns to gear 3.
   The wing knob has an auto-return function in this position – once the wing knob is released, it returns to position 3.
   Repeat action reverts the settings to their previous state – gear 3. During the operation of the 4th gear (BOOST function), the light indicator flashes white.
6. By turning the wing knob anti-clockwise from position 0 to position A, the automatic function of adjusting the motor's speed depending on the conditions detected under the hood is switched on – Automatic.
   The wing knob has an auto-return function in this position – once the wing knob is released, it returns to position 0.
   When the device operates in the Automatic mode, the light indicator lights up white.

Maintenance

ATTENTION! Before performing any maintenance operation, isolate the hood from the electrical supply by switching off at the connector and removing the connector fuse.

Or if the appliance has been connected through a plug and socket, then the plug must be removed from the socket.

Cleaning

The cooker hood should be cleaned regularly (at least with the same frequency with which you carry out maintenance of the fat filters) internally and externally. Clean using the cloth dampened with neutral liquid detergent. Do not use abrasive products.

DO NOT USE ALCOHOL!

WARNING: Failure to carry out the basic cleaning recommendations of the cooker hood and replacement of the filters may cause fire risks.

Therefore, we recommend observing these instructions.

The manufacturer declines all responsibility for any damage to the motor or any fire damage linked to inappropriate maintenance or failure to observe the above safety recommendations.

Grease filter

Traps cooking grease particles.

This must be cleaned once a month (or when the filter saturation indication system – if envisaged on the model in possession – indicates this necessity) using non aggressive detergents, either by hand or in the dishwasher, which must be set to a low temperature and a short cycle.

When washed in a dishwasher, the grease filter may discolour slightly, but this does not affect its filtering capacity.

To remove the grease filter, pull the spring release handle.

Replacing lamps

Disconnect the hood from the electricity.

Warning! Prior to touching the light bulbs ensure they are cooled down.

1. Remove the bulb halogen
2. Replace burned-out light bulb. Use only the contribution GU10 bulbs. After replacing the bulb needs to be cleaned.

If the lights do not work, make sure that the lamps are fitted properly into their housings before you call for technical assistance.