Neo 3 - Tent Zempire - Free user manual and instructions

Brand	Zempire
Model	Neo 3
Product Type	Tent
Capacity	3 persons
Pitching Method	Inner tent first, then fly
Poles	4 sections, color-coded (red and blue)
Fly Material	Polyester (assumed from typical tent)
Floor Material	Polyester (assumed from typical tent)
Front Identification	Orange webbing loops on fly
Pegging Angle	45°
Ventilation	Windows and guy ropes should be used for adequate airflow
Guy Ropes	Included; peg out at all times during use
Fire Safety	Do not use open flame inside; fabric is fire retardant but not fireproof
Care – Wet Storage	Never pack away wet; dry completely to prevent mildew
Mildew Treatment	Wash with warm water and soft brush; do not use detergents
Storage Preparation	Clean all pegs and poles before storing
Country of Origin	New Zealand (brand)
Manual Availability	Free PDF download
Assembly Difficulty	Easy, with clear color-coded poles

Frequently Asked Questions - Neo 3 Zempire

How do I pitch the Zempire Neo 3 tent?

Clear the site of sharp objects and choose a flat area. Spread out the inner tent (white) with the round door at the front. Assemble the 4 pole sections, ensuring they do not snap together. Thread the RED poles through the diagonal pole sleeves and insert ends into the pins. Thread the BLUE poles through the front and rear sleeves and insert ends into rings. Peg out all peg points around the inner tent, pegging through the webbing loop at the base of each pole. Finally, pull the fly over the inner tent, aligning the ORANGE webbing loops to mark the front, and attach the velcro loops inside the fly around the corresponding pole sleeves. Peg the fly directly into the ground where no inner peg exists, ensuring space between inner and fly.

What do the color-coded poles mean?

The RED poles are threaded through the diagonal pole sleeves across the center of the tent. The BLUE poles are threaded through the pole sleeves at the front and rear of the tent. This color coding simplifies assembly.

How should I peg the tent?

Insert pegs at a 45° angle for maximum holding power. For the inner tent, peg through the webbing loop at the base of each pole rather than the ring. Peg out all peg points around the inner tent, then attach the fly's elastic loops over existing inner pegs or peg the fly directly into the ground where needed.

How do I ensure proper ventilation?

It is recommended that guy ropes are pegged out at all times and windows are opened whenever possible to allow adequate airflow and prevent condensation.

Can I use a stove or open flame inside the tent?

No. Do not use an open flame inside your tent. The fabric has been treated with a fire retardant but is in no way fireproof. Open flames can cause fire and damage.

How should I clean and store the tent?

Never pack your tent away wet. If you must pack it wet, dry it completely as soon as possible to prevent mildew. Clean all pegs and poles before storing. If mildew forms, wash with warm water and a soft brush; do not use detergents.

What is the front of the tent?

The front is indicated by the ORANGE webbing loops on the fly. The inner tent's round door is located at the front.

How do I set up the fly?

After pegging the inner tent, pull the fly over it. Align the orange webbing loops to the front. Connect the velcro loops inside the fly around the cut-outs on the corresponding pole sleeves. Then attach the elastic loops over existing inner pegs or peg the fly directly into the ground, ensuring significant space between the inner and fly.

What should I do if the tent gets wet?

If you must take down your tent when wet, ensure you dry it completely as soon as possible to prevent mildew formation. Never store a wet tent.

Where is Zempire based?

Freedom Zempire is proud to be a 100% New Zealand owned and operated business.

USER MANUAL Neo 3 Zempire

1. Clear your site making sure there are no sharp objects where you are going to pitch your tent. Try to get a site that is as flat as possible. Spread out the inner tent (White), the round door is located at the front.

1. Assemble the 4 pole sections. Ensure that the poles do not snap together.

2. Thread the RED poles through the pole sleeves that run diagonally across the centre of the tent. Insert the ends of the poles into the pins located below each pole sleeve.

1. Thread the BLUE poles through the pole sleeve at the front and rear of the tent. Insert the pole ends into rings.

1. Peg out all the peg points around the inner tent. The peg points at the base of each pole should be pegged through the webbing loop rather than the ring.

1. Pull the fly over the inner tent. The ORANGE webbing loops indicate the front of the fly. Connect the velcro loops inside the fly around the cut outs on the corresponding pole sleeve.

2. Attach the elastic loop over the existing inner pegs. Where there is no existing peg, peg the fly directly into the ground ensuring there is significant space between the inner and fly.

1. It is recommended that guy ropes are pegged out at all times and windows are opened whenever possible to allow adequate ventilation.

Insert pegs at a 45° angle

PITCHING INSTRUCTIONS - NEO 3

1. Ensure guy ropes are pegged out at all times during use
2. Never pack your tent away wet. If you must take your tent down when wet, ensure that you dry you tent completely as soon as possible to prevent mildew forming.
3. If mildew does form on your tent wash off pours with warm water and a soft brush to prevent further growth. Do not use detergents.
4. Do not use an open flame inside your tent. The fabric has been treated with a fire retardant but is in no way fire proof
5. Clean all pegs and poles before storing

Freedom zempire

Freedom Zempire is proud to be a 100% New Zealand owned and operated business.

For more information about this and other great products we offer please visit our website.

pitching

NEO ³ instructions