XMS-2624P - Network switch Luxul - Free user manual and instructions

Product Type	26-Port/24 PoE+ Gigabit Managed Switch
Ports	26 x Gigabit Ethernet RJ-45 (ports 1-24 PoE+, 25-26 non-PoE) + 2 x Gigabit SFP+
PoE Standards	PoE+ (802.3at/af)
PoE Budget	370W total, up to 25.5W per port
Management	Web-based GUI (default IP: 192.168.0.4)
Default Username/Password	admin / admin
Power Supply	Internal, 100-240VAC, 50/60Hz
Console Port	RJ-45 console port
Mounting	Rack-mountable (19-inch) with included ears; desktop with included rubber feet
LED Indicators	System, Link/Act per port (green=1000M, yellow=10/100M, flashing=activity), PoE per port (green=power on, yellow=fault)
Reset Button	Short press (3s) reboots; long press (8s) restores factory defaults
Cabling Recommendation	CAT5e UTP or better; CAT6 recommended for 1000Mbps
Included Accessories	Rack mount kit, rubber feet, power cord, console cable
Dimensions	Standard 1U rack-mount (exact dimensions not specified)
Weight	Not specified

Frequently Asked Questions - XMS-2624P Luxul

What is the default IP address of the XMS-2624P?

The default IP address is 192.168.0.4. The default username and password are both admin.

How do I reset the switch to factory defaults?

With the switch powered on, press and hold the Reset button for about eight seconds until both the Link/Act and PoE LEDs turn off, then release. The switch will reboot with factory settings.

What is the total PoE power budget?

The total PoE power budget is 370W, with a maximum of 25.5W per port on ports 1-24.

What type of cabling should I use?

Luxul recommends at least CAT5e UTP cabling. For best performance at 1000 Mbps, use CAT6 UTP.

How many PoE+ ports does the switch have?

The switch has 24 PoE+ ports (ports 1-24). Ports 25 and 26 are Gigabit Ethernet only (non-PoE).

Does the switch support SFP+ ports?

Yes, the XMS-2624P has two Gigabit SFP+ ports for fiber or other media connections.

Can I mount the switch in a rack?

Yes, the switch includes a rack mount kit for installation in a standard 19-inch rack. It also includes rubber feet for desktop use.

What do the LED indicators mean?

The System LED shows green flashing for normal operation. Port Link/Act LEDs: green for 1000Mbps, yellow for 10/100Mbps, flashing for activity. PoE LEDs: green when powering a device, yellow for a fault.

How do I access the web configuration?

Connect your computer to any port, set your computer to a static IP in the 192.168.0.x range, then open a browser and go to http://192.168.0.4. Log in with username and password admin.

What is the power supply specification?

The switch has an internal 370W power supply that supports 100-240VAC at 50/60Hz.

USER MANUAL XMS-2624P Luxul

Front view of a black LUXUL network switch device with multiple Ethernet ports (no visible text or labels beyond branding)

26-Port/24 PoE+ Gigabit Managed Switch

XMS-2624P

Includes:

26-Port PoE+ Switch
Rack Mount Kit
Rubber Feet
Power Cord
Console Cable

INSTALLATION AND SETUP

1 Physical Installation

The XMS-2624P can easily be installed in a standard 19" rack. Two mounting ears are included for installing and stabilizing the switch. When attaching the mounting ears and installing the switch in a rack, please refer to the following illustration:

3D diagram of a device with labeled components and arrows indicating flow or movement (no readable text or symbols)

Rack-Mounting the XMS-2624P

Using the included screws to attach the mounting ears to each side of the switch.

Mount the switch in the rack with the LEDs facing outwards. Be sure the switch is level and properly secured in the rack.

Desktop Setup

For use as a desktop device, position and apply the included rubber feet to the bottom of the XMS-2624P.

Connecting Ethernet and Power

Ethernet and Power Connections

Use any one of the 26 Ethernet ports to connect the XMS-2624P to any Ethernet-enabled device, including servers, routers or other switches. No crossover cable is necessary.

The XMS-2624P supports 10/100/1000 Mbps Ethernet; 10/100 Mbps half/full-duplex mode and 1000 Mbps full-duplex mode. Ports 1-24 are PoE+ and are enabled by default. Ports 25 and 26 are Gigabit Ethernet only (non PoE).

Use the included power cable to connect the XMS-2624P to a surge-protected outlet. The AC input socket is on the rear panel. The built-in power supply supports 100\~240VAC at 50/60Hz.

Network Cabling

Luxul recommends at least Cat-5e unshielded twisted pair (CAT5e UTP) cabling. To ensure best performance and stable data transmission at 1000 Mbps, use Category-6 unshielded twisted pair (CAT6 UTP).

CAUTION: Multiple Uplink channels can create loops, resulting in network failure. Ensure only one Uplink channel exists between switches or between the XMS-2624P and a router.

NOTE: When powering up, the port LEDs may take a moment to initialize. This is normal as the XMS-2624P initialization and startup sequence completes.

NOTE: The XMS-2624P has an internal 370W power supply. Do not exceed 25.5W each or 370W combined consumption of all external PoE devices.

Preparing for Access

IP Addressing

If the XMS-2624P is connected to a network with a 192.168.0.X address scheme, and your computer shares a similar address on the same network, you can skip to the next step, Access and Setup

Note: If another device on your network shares the 192.168.0.4 address, you'll need to temporarily reassign or remove that device while you configure the XMS-2624P.

If your network uses an address scheme other than 192.168.0.X, you'll need to set a temporary static IP address on the computer you're using for configuration. To do so, set the IP address of your computer to an address in the 192.168.0.X range, then set the Gateway/Router address to 192.168.0.4 (the default IP address of the XMS-2624P).

Once you're finished configuring the switch, you can return your computer's IP configuration to normal, typically "Obtain Automatically/DHCP."

Note: Visit http://luxul.com/ip-addressing to learn more about changing your computer's IP address and getting connected.

Access and Setup

Getting Connected

Use an Ethernet cable to connect your computer to the XMS-2624P, then power on the switch.

Logging In

To access the XMS-2624P web configuration, open your web browser and enter the switch's default 192.168.0.4 IP address in the address field. Log in to the switch using the default user name and password:

Default IP: 192.168.0.4

Username: admin

Password: admin

Select the menu items on the left to view and/or modify the configuration.

Refer to the Quick Setup Guide at Luxul.com for more detailed information on setup, IP configuration and routing, PoE, VLANs, Spanning Tree, and Stacking.

Hardware Operation

Front Panel

The front panel of the XMS-2624P includes 26 Gigabit Ethernet RJ-45 ports, two Gigabit SFP+ ports, status-, link- and PoE LEDs, a Mode/Reset button and an RJ-45 Console port.

XMS-2624P Front Panel View

Rear Panel

The rear panel of the XMS-2624P features a standard AC power input along with a power switch.

LED Indicators

The LED indicators on the XMS-2624P include System, Link/Act and PoE LEDs, and an LED for each port. These LED indicators show the operating status of the XMS-2624P and each port connection.

Mode/Reset Button to Change LED Functionality

Tapping the Mode/Reset button briefly switches the port indicator between displaying port link speed and PoE status.

The following chart shows the LED indicators of the XMS-2624P along with an explanation of the indicator's properties:

Indicator Name	Description
System	Green Flashing Indicates normal operation.
	Green On Indicates a malfunction. Contact support.
	Red On Indicates power-on system initialization.
	Off	Indicates startup/initialization process or that power is not on.
Port Link/Act Status 1-26	Green	1000Mbps device connected to the port.
	Yellow	10/100Mbps device connected to the port.
	Flashing	Port receiving or transmitting data.
	Off	Nothing connected to the port.
Port PoE Status 1-24	Green	Switch is providing PoE power to a device.
	Yellow	PoE is off due to a fault or because the connected device is exceeding power limit.
	Off	Port disconnected or link failed.

Note: At startup, the port LEDs will flash briefly during a self-test.

Mode/Reset Button to Reset/Restore

The Reset button (located at the lower-left corner of the front panel) is used to reset (reboot) the switch, or to restore the switch to factory default settings.

To Reboot/Reset the Switch: With the XMS-2624P powered on, press the Reset button for approximately three seconds until the Link/Act and PoE LEDs both light, then release the button.

CAUTION: Do not hold the button for more than four seconds. Doing so could erase all settings and restore factory defaults.

To Restore Default Settings: With the XMS-2624P powered on, press and hold the Reset button approximately eight seconds, until both the Link/Act and PoE LEDs turn off, then release the Reset button and the switch automatically restores factory default settings and reboots. Once the System LED starts flashing again, the XMS-2624P is running with factory defaults.

CAUTION: Please note that restoring Default Settings will remove any/all custom configuration.

Sales

801-822-5450

[e-mail]

Technical Support

801-822-5450

[e-mail]

Copyright and Trademark Notices

No part of this document may be modified or adapted in any way, for any purposes without permission in writing from Luxul. The material in this document is subject to change without notice. Luxul reserves the right to make changes to any product to improve reliability, function, or design. No license is granted, either expressly or by implication or otherwise under any Luxul intellectual property rights. An implied license only exists for equipment, circuits and subsystems contained in this or any Luxul product.

© Copyright 2017 Luxul. All rights reserved. The name Luxul, the Luxul logo, the Luxul logo mark and Simply Connected are all trademarks and or registered trademarks of Luxul Wireless, Inc. All other trademarks and registered trademarks are property of their respective holders.

LUX-QIG-XMS-2624P-v8 02131809

A brand of legrand®

Abstract network diagram with interconnected nodes and lines on a dark background (no text or symbols)