58SX Mark II - Saw MTM - Free user manual and instructions
Find the device manual for free 58SX Mark II MTM in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Chainsaw |
| Brand | MTM |
| Model | 58SX Mark II |
| Power Source | Gasoline |
| Engine Displacement | 58 cc |
| Bar Length | 18 inches (45 cm) |
| Chain Pitch | 0.325 inch |
| Chain Gauge | 0.058 inch |
| Chain Type | Low kickback |
| Fuel Capacity | 550 ml |
| Oil Capacity | 260 ml |
| Weight (without bar and chain) | 5.8 kg |
| Overall Dimensions (L x W x H) | 420 x 240 x 280 mm |
| Noise Level (LwA) | 110 dB(A) |
| Vibration Level (front/rear handle) | 4.0 / 5.5 m/s² |
| Safety Features | Chain brake, hand guard, anti-vibration system |
| Maintenance | Clean air filter, sharpen chain, check oil level |
| Spare Parts Available | Replaceable bar, chain, spark plug, air filter |
| Warranty | 2 years |
| Recommended Fuel Mix | 50:1 (gasoline to 2-stroke oil) |
Frequently Asked Questions - 58SX Mark II MTM
What is the correct fuel mixture for the MTM 58SX Mark II chainsaw?
Use a 50:1 ratio of unleaded gasoline (min. 90 octane) to high-quality 2-stroke oil. Mix thoroughly before filling the tank.
How do I adjust the chain tension on the 58SX Mark II?
Loosen the bar nuts, turn the tensioning screw clockwise to tighten the chain until it snaps back into place when pulled 1-2 mm from the bar, then retighten the nuts.
What type of chain oil should I use?
Use a high-quality biodegradable chain and bar oil, preferably with adhesion additives. Do not use used or recycled oil.
How often should I clean the air filter?
Check and clean the air filter after every 10 hours of use or more frequently in dusty conditions. Wash in warm soapy water and dry thoroughly before reinstalling.
What is the recommended bar length for the 58SX Mark II?
The saw is designed for bars up to 18 inches. Using a longer bar may reduce performance and increase wear.
How do I start the chainsaw?
Set the master control lever to start, pull the choke fully out, press the purge bulb 5-6 times, pull the starter rope briskly until the engine almost starts, then push the choke in and pull again to start.
How do I maintain the chain sharpness?
Use a round file of the correct diameter (typically 4.8 mm for 0.325 pitch) and file each cutter at the same angle (30°) with even strokes. Use a file guide for consistency.
What safety features does the 58SX Mark II have?
It includes a chain brake that stops the chain instantly, a front hand guard, and an anti-vibration system to reduce operator fatigue.
Why is the chain not getting enough oil?
Check that the oil cap is vented, the oil pump is adjusted to the correct flow (usually 2-3 drips per minute), and the oil passages are not blocked.
Where can I find spare parts for the MTM 58SX Mark II?
Spare parts such as bars, chains, spark plugs, and air filters are available from MTM dealers or authorized online retailers. Always use genuine parts.
User questions about 58SX Mark II MTM
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Saw in PDF format for free! Find your manual 58SX Mark II - MTM and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. 58SX Mark II by MTM.