412-006 - Household Fan Anslut - Free user manual and instructions

Product Type	Domestic Floor Fan
Model	412-006
Brand	Anslut
Power Supply	230 V ~ 50 Hz
Rated Power	50 W
Nominal Output	38.6 W
Air Flow	47 m³/min
Air Velocity	2.7 m/s
Operating Value	1.1 (m³/min)/W
Noise Level	54 dB
Standby Power	0 W
Cable Length	1.3 m
Weight	3.4 kg
Dimensions	Height 108 cm, Base 125 x 940 mm
Speed Settings	3 speeds (Low, Medium, High)
Timer	0.5 to 7.5 hours (increments: 0.5h, 1h, 2h, 3h, 4h, 7.5h)
Oscillation	Yes, with indicator light
Tilt Adjustment	Yes, via retaining screw
Remote Control Range	Approx. 4.5 m at 30° angle
Remote Control Batteries	2 x AAA (not included)
Grille Diameter	Estimated 40-50 cm (not specified)
Material	Plastic and metal components
Maintenance	Clean with damp cloth, vacuum vents; do not use solvents
Safety Features	Overheat protection? Not specified; follow manual safety instructions
Certification	Complies with IEC 60879:1986

Frequently Asked Questions - 412-006 Anslut

How do I assemble the fan base and motor housing?

Position crossbar A and crossbar B to form a cross, align the holes with the flange on the outer tube, and screw them together. Insert the inner tube into the outer tube, adjust the height, and tighten the height adjustment sleeve. Finally, attach the distribution box using the locking screw.

How do I attach the fan blade and grille?

Remove the plastic nut from the motor housing, place the rear grille with handle upward, and tighten the plastic nut. Fit the fan blade onto the motor shaft, secure hub cover, then attach the front grille with screw and nut, and press the grille clips into place.

What batteries does the remote control use?

The remote control requires 2 x AAA batteries (sold separately). Insert them with correct polarity, do not mix old and new batteries, and replace both at the same time. Recycle used batteries properly.

How do I operate the fan using the control panel?

Plug in the fan, press the power switch to turn it on. Use the speed button to cycle through low, medium, and high speeds. Press the oscillation button for side-to-side movement. Use the timer button to set a run time from 0.5 to 7.5 hours.

Can I control the fan with the remote control?

Yes, the remote control has the same functions as the control panel. Point it at the receiver (within 4.5 m and 30° angle) and press the desired button for power, speed, oscillation, or timer.

How do I adjust the tilt of the fan head?

Switch off and unplug the fan. Remove the retaining screw on the motor unit, tilt the motor to the desired angle, then retighten the screw securely. Do not force the tilt mechanism.

What is the maximum timer setting?

The timer can be set up to 7.5 hours. Press the TIMER button repeatedly to add 0.5h, 1h, 2h, 3h, 4h, and 7.5h increments. The fan will automatically switch off once the set time elapses.

How should I clean and maintain the fan?

Always unplug before cleaning. Use a soft cloth or sponge dampened with mild detergent and water. Wipe the exterior and vacuum the ventilation openings gently. Never use strong detergents or allow water into the motor housing or control panel.

What safety precautions should I take?

Do not use near water, heat sources, or with a speed controller. Keep children supervised, never leave unattended while on, and do not operate if damaged. Unplug when not in use. Avoid inserting objects into moving parts.

What should I do if the fan does not start?

Check that the power cord is plugged into a suitable outlet and the mains voltage matches the rating. Ensure the power switch is pressed. If the fan still does not start, check the remote control batteries (if using remote) or contact an authorized service center.

USER MANUAL 412-006 Anslut

EN Operating instructions (Translation of the original instructions)

Jula reserves the right to make changes. In the event of problems, please contact our service

department.

www.jula.com

Tillverkare/ Produsent / Produenci/ Manufacturer

Jula AB, Box 363, 532 24 SKARA

Importör/ Importör/ Importer/ Importer

Care for the environment!

Must not be discarded with household waste! This product contains electrical or electronic components that should be recycled. Leave the product for recycling at the designated station e.g. the local authority's recycling station.

SVENSKA....6

SÄKERHETSANVISNINGAR....6

TEKNISKA DATA....7

BESKRIVNING 8

DELLAR 8

MONTERING 9

MONTERING AV FOT OCH MOTORHÖLIF 9

MONTERING AV FLAKTROTOR OCH GALLER....9

ISÄTTNING AV BATTERIER I EJÄRRKONTROLL....9

HANDHAVANDE 10

MANÖVERPANEL....10

DJARRKONTROLL 12

UNDERHÅLL 13

NORSK 14

SIKKERHETSANVISNINGER 14

TEKNISKE DATA 15

BESKRIVELSE....16

DFLER 16

MONTERING 17

MONTERING AV FOT OG MOTORDEKSEL....17

MONTERING AV VIFTEROTOR OG GITTER 17

SETTE INN BATTERIER I FJERNKONTROLL....17

BRUK....18

BETJENINGSPANEL 18

FJERNKONTROLL....20

VEDLIKEHOLD 21

POLSKI 22

ZASADY BEZPIECZEŃSTWA 22

DANE TECHNICZNE 23

OPIS 24

OBSTUGA 26

PANEL STEROWANIA....26

PILOT ZDALNEGO STEROWANIA 28

KONSERWACJA 29

ENGLISH 30

SAFETY INSTRUCTIONS....30

TECHNICAL DATA....31

DESCRIPTION 32

PARTS 32

ATTACHMENT 33

ASSEMBLY OF THE BASE AND MOTOR HOUSING 33

ASSEMBLY OF THE FAN BLADE AND GRILLE....33

INSERTING THE BATTERIES IN THE REMOTE CONTROL 33

USE....34

CONTROL PANEL 34

REMOTE CONTROL 36

MAINTENANCE 37

SÄKERHETSANVISNINGAR

UNDERHÄLL

1. Frontcitter

2. Låseskrue

3. Deksel for vifterolomav

4. Indre idr

5. Viflerotor

6. Høydeinnstillingshylse

7. Plastmutter

8. Yiheng

9. Bakre gitter

10. Pyntedeksel, fot

11. Motorskel

12. Skrue

13. Knapp for swinging

14. Tverstykke A

15. Motordeksel

16. Tverstykke B

17. Festeskrue

18. Skrue og mutter

19. Books

MONTERING

MONTERING AV FOT OG MOTORDEKSEL

VEDLIKEHOLD

KONSERWACJA

Read the Operating Instructions carefully before use!

Save these instructions for future reference.

Always follow these basic safety instructions when using electrical appliances.

WARNING! Follow the instructions below to reduce the risk of burns, fire, electric shock or personal

injury

• Check that the mains voltage corresponds to the rated voltage on the type plate.
• Do not use the appliance with a speed controller – risk of electric shock
• The appliance is not intended to be used by persons (children or adults) with any form of functional disorders, or by persons who do not have sufficient experience or knowledge on how to use it, unless they have received instructions concerning the use of the appliance from someone who is responsible for their safety.
• Keep children under supervision to make sure they do not play with the appliance.

- Never leave the appliance unattended when switched on.

- Do not use the appliance if it is damaged or not working properly, or if the power cord or plug are damaged. Take the appliance to an authorised service centre to be checked, repaired or adjusted.

- Do not attempt to repair the appliance yourself. Return it to an authorised electrician or service centre.

- Do not expose the appliance, the power cord or the plug to water or any other liquid – risk of electric shock.

- Do not use the appliance close to baths, showers, wash basin or swimming pools.

- Do not install the appliance near sources of heat, e.g. radiators, cookers or other equipment that produces heat.

- Do not expose the appliance to high temperatures or direct sunlight.

- Do not subject the appliance to impact or continuous vibration.

- Do not expose the machine to a dusty environment.

- Do not place the appliance so that it does not receive sufficient ventilation (for example, in a cupboard or on a shelf).

- Do not place the appliance on an uneven surface.

- Switch off the appliance and unplug the power cord when the appliance is not in use, and before assembling/dismantling parts or cleaning. Do not start the machine until it is fully assembled.

- Avoid contact with moving parts. Never insert any objects or body parts in the equipment's

EN

• Switch off the appliance, unplug the power cord, and wait until all moving parts have completely stopped before moving the appliance.
• Do not use accessories other than those recommended or sold by the appliance manufacturer. The use of other accessories can result in fire, electric shock or personal injury
• A damaged power cord must be replaced by an authorised service centre, or qualified person, to ensure safe use.

TECHNICAL DATA

Air flow 47m3/min

Power in standby mode 0 W

Weight 3,4 kg

Noise level 54 dB

Operating value standard IFC 60879:1986 (corr. 1992)

Nominal output 38,6 W

Cable length 1,3 m

Operating value 1,1 (m2/min)/W

Air velocity 2,7 m/s

Voltage 230 V

Dimensions H108 125x940 cm

Power 50 W

DESCRIPTION

PARTS

1. Front grille
2. Casing for the fan blade hub
3. Fan blade
4. Plastic mul
5. Rear grille
6. Motor shaft
7. Oscillation button
8. Motor housing
9. Retaining screw

10. Electrical box

11. Locking screw

12. Inner tube
13. Height adjustment sleeve
14. Guler tube
15. Decorative cover, base
16. Screw
17. Crossbar A
18. Crossbar B
19. Screw and nut

ATTACHMENT

ASSEMBLY OF THE BASE AND MOTOR HOUSING

• Remove the 4 screws from the crossbars. Position crossbar A (17) and crossbar B ('18) so they form a cross.
• Aligning the 4 holes in the cross bars with the holes in the flange in the outer tube (14). Screw the flange on the cross bars with the 4 screws.
• Remove the height adjustment sleeve (13) from the upper part of the inner tube (12). Fit the decorative cover (15) on the tube.
• Refit the height adjustment sleeve (13) on the upper part of the inner tube (12). Pull the inner tube (12) out from the outer tube (14) to the required height and tighten the height adjustment sleeve (13).
• Loosen the locking screw (11) slightly by turning anti-clockwise. Fit the distribution box (10) on the inner tube (12) and tighten the locking screw (11). Check that the locking screw (11) is properly tightened.

ASSEMBLY OF THE FAN BLADE AND GRILLE

• Remove the plastic nut (4) from the front of the motor housing (8) by turning anti-clockwise.
• Place the rear grille (5) against the front of the motor housing (8), with the handle facing upwards. The guide pins on the motor housing (8) should mate in the holes in the rear grille (5).
• Tighten the plastic nut (4) clockwise. Do not overtighten.
• Fit the fan blade (3) on the motor shaft (6), with the slot at the rear of the blade over the pin in the motor shaft (5).
• Secure the hub cover (2) in position by turning it anticlockwise.
• Remove the screw and nut (19) from the rear edge of the grille.
• Place the front grille (1) against the rear grille (5), so that the holes along the edges are aligned. Insert the screw through the hole and screw on the nut. Do not tighten fully.
• Press the grille clips in position over the edge of the grille.
• Tighten the nut on the screw through the edge of the grille.

INSERTING THE BATTERIES IN THE REMOTE CONTROL

- Open the battery cover (see the figure below).

• Insert the batteries with the polarity shown in the battery compartment.
• Do not use rechargeable batteries. Do not mix old and new batteries, or different types of batteries.
• Always replace both the batteries at the same time.
• 2 x AAA batteries (sold separately).
• Recycle used batteries in accordance with local regulations.

USE
CONTROL PANEL

EN

IMPORTANT!

- Put the appliance in a suitable place as set out in the safety instructions.

- Route the power cord so that there is no risk of tripping over it.

- Do not mount the appliance on a wall or ceiling.

1. Check that the mains voltage corresponds to the rated voltage on the type plate. Plug the power cord into a suitable mains outlet.

2. Voltage status lamp comes on.

3. Start the appliance by pressing the power switch once. The fan starts at a low speed and speed status lamp 1 comes on. Press the power switch again to switch off the appliance.

4. Press the SPEED button repeatedly

- Low speed (speed status light 1 comes on)

- Medium speed (speed status light 2 comes on)

- High speed (speed status light 3 comes on)

• For oscillation, press the oscillation button marked SWING. The oscillation status light comes on and the fan starts to oscillate. To cancel oscillation, press the oscillation button marked SWING again.
• When the appliance start and the desired speed set, the required running time can be set using TIMER. Press the TIMER button repeatedly until the status light for the desired running time comes on. The appliance switches off automatically when the set time is reached. The operating time is adjustable between 0.5 and 7.5 hours. The running time is the sum of the time indicated by the status lamps.
• The motor unit can be tilted upwards or downwards to the desired airflow direction. Remove the retaining screw (9) and adjust the motor unit to the desired angle. Tighten the screw.
• Switch off the appliance and unplug the power cord when it is not in use.

REMOTE CONTROL

Using the remote control

The remote control has the same functions as the control panel. Follow the instructions below to obtain the best results.

• Direct the remote at the receiver and press the desired button.
• The range of the remote control is approximately 4.5 m, at a 50° angle to the receiver (see the figure).

EN

MAINTENANCE

• Switch off the appliance and unplug the power cord when the appliance is not in use, and before assembling/dismantling parts or cleaning.
• Keep the ventilation openings clean. Vacuum if necessary. Do not insert objects into the ventilation openings.
• Clear the appliance with a cloth or sponge, moistened with a mild detergent. Wipe off the machine with a cloth or sponge, moistened with clean water.
• Always be very careful to ensure that no water or other liquid enters the motor housing or control panel.

IMPORTANT! Do not use strong detergent or solvents.