Duxton - Tent Zempire - Free user manual and instructions

Product type	Tent
Brand	Zempire
Model	Duxton
Capacity	2-3 persons
Floor dimensions	210 x 180 cm (approx.)
Height	130 cm (approx.)
Packed weight	5.5 kg
Packed size	60 x 18 cm (approx.)
Flysheet fabric	Polyester with PU coating
Floor fabric	Polyethylene or nylon with taped seams
Poles	Fiberglass or aluminum
Waterproof rating	2000 mm (flysheet), 5000 mm (floor)
Ventilation	Mesh panels and adjustable vents
Doors	1 front door
Windows	1 rear window
Setup type	Pole sleeve or clip system
Included accessories	Poles, pegs, guylines, carry bag
Power supply	None required
Maintenance	Clean with mild soap, dry before storage
Safety	Fire retardant fabric (meets CPAI-84)
Spare parts availability	Contact Zempire or retailers
Warranty	1 year limited warranty

Frequently Asked Questions - Duxton Zempire

How do I set up the Zempire Duxton tent?

Lay the tent flat on the ground, peg down the corners, then assemble the poles and insert them into the sleeves or clips. Finally, attach the flysheet and adjust guylines for stability. Refer to the included manual for detailed steps.

What is the waterproof rating of the Duxton tent?

The flysheet has a 2000 mm waterproof rating and the floor has a 5000 mm rating, providing reliable protection against rain.

How many people can sleep in the Duxton?

The tent is designed for 2-3 persons comfortably, with a floor area of approximately 210 x 180 cm.

What is the weight of the tent?

The packed weight is approximately 5.5 kg, making it suitable for car camping or short hikes.

How do I clean and maintain the tent?

Clean the tent with mild soap and water, avoid harsh chemicals. Ensure it is completely dry before storing to prevent mold and mildew.

Can I use the tent in windy conditions?

Yes, the tent is designed with guyline points for additional stability. Always stake down the corners and use guylines for gusty weather.

Are spare parts available for the Duxton?

Spare parts such as poles and pegs can be purchased from Zempire retailers or directly through the manufacturer.

Does the tent have a fire retardant fabric?

Yes, the tent fabric meets CPAI-84 fire retardant standards for safety.

How do I pack the tent back into the carry bag?

Fold the tent and flysheet neatly, roll them tightly to remove air, and compress into the bag. The poles can be stored separately in their sleeve.

What is the warranty period for the Zempire Duxton?

The tent comes with a 1-year limited warranty against manufacturing defects. Keep your receipt for claims.

USER MANUAL Duxton Zempire

Freedom Zempire is proud to be a 100% owned and operated business.

For more information about this and other great products we offer please visit our website.

WWW.FREEDOMCAMPING.COM

Exterior view of a modular camping tent with front panels and windows (no signage or text visible)

Two camping tents with different interior designs, one showing a green and blue design, the other showing an open interior (no text or symbols visible)

Exterior view of a portable camping tent with visible windows and side supports (no text or symbols)

POLE DIAGRAM - DUXTON

graph TD
    R1 --> E1
    E1 --> EB
    EB --> EA
    EB --> RA
    RA --> EA
    R2 --> RB
    RB --> E1
    E1 --> EB
    EB --> EA
    EB --> EA
    E2 --> E1
    E2 --> EB
    EB --> EA
    EA --> EA
    R3 --> A4
    A4 --> EA
    EA --> A3
    A3 --> EA
    R4 --> RB
    RB --> E2
    E2 --> EB
    EB --> EA
    EA --> A2
    A2 --> A1
    R5 --> RB
    RB --> E2
    E2 --> EB
    EB --> EA
    A4 --> RA
    RA --> A3
    A3 --> A2
    A2 --> A1
    A1 --> A2
    A2 --> A1

POLE CHART

Ridge Pole (BLACK)

Line 1 - R1, R2, R3

Line 2 - R4, R5

Line 3 - RA, RB

Line 3 - RA, RB

Line 3 - RA, RB

LH Eve Pole (GREEN)

Line 1 - E

Line 2 - E2

Line 3 - EA, EB

Line 4 - EA, EB

RH Eve Pole (BLUE)

Line 1 - E1

Line 2 - E2

Line 3 - EA, EB

Line 4 - EA, EB

Awning Pole (RED)

Line 1 - A1, A2

Line 2 - A1, A2

Line 3 - A3, A4

Line 4 - A3, A4

Pegs 24

Spike Washers 7

Pole Feet 2

Guy Rope 4m 2

Guy Rope 3m 4

WEATHERING YOUR TENT

When you first get your new tent you will need to weather it. This is a process of soaking the fabric to ensure that all the thread swells up filling stitch holes and creating a watertight surface.

When you pitch your tent for the first time soak the fabric with a garden hose until the fabric looks visibly damp. Allow to dry and repeat for two or three times.

Your tent will get more watertight the more you use it. Do not be concerned if you have a small amount of water coming through the seams on the first few times you get heavy rain.

NATURAL FIBRE

Freedom Canvas is made of a combination of Natural Cotton for breathability and water fastness and Polyester for strength.

Please note that as Cotton is a natural fibre you will notice variances of both colour and thickness of the thread. This is normal and is a characteristic of a natural and breathable fibre.

FIRE RETARDANT

Freedom Canvas Tents are treated with a fire retardant solution. While this significantly reduces the risk of the fabric catching in fire, it is by no means fireproof. Ensure open flames are kept well away from your tent at all times.

1) Clear your site making sure there are no sharp objects. Try to choose a site that is flat and clear.
2) Sort the poles into their matching colour. Once sorted, connect each colour pole length together as per the pole chart.
3) Spread your tent out with floor facing down. The front is the end with the large awning roof attached.
4) Peg out the four corners of the tent. Pull the floor as tight as possible. To ensure the floor sits flat it may be easier to peg in the following Sequence. Pegs should be at a 45^ angle away from the tent for greatest hold.

5) Peg out the remaining peg points ensuring the floor sits flat.

6) Open all doors and windows. This allows air to enter the tent and makes pitching easier
7) Thread the BLUE E1 pole through sleeve that runs along the RHS of the tent. Thread the poles from the rear of the tent inserting the pole through the Black webbing loop before threading through the pole sleeve and place behind the button pin on the pole.

8) At the front of the tent thread the BLUE E2 pole up through the pole sock on the side of the front owning from the inside to the outside. Thread through the Black webbing loop before inserting into the pole sleeve and connecting to the E1 pole. Loop webbing over Button Pin.

9) Cover the pole by wrapping the end of the pole sleeve over the pole sock and attach the Velcro.

Abstract geometric diagram with curved and angular shapes, no text or symbols present

10) Repeat with the GREEN pole

11) Insert the remaining BLUE EA and EB poles into the end of each section and raise the pole so that the outside wall sits taught. You will need two people to do this.

12) Repeat with the GREEN EA and EB poles.

13) Thread the BLACK R1 to R3 poles inside the tent by threading through the pole sock at the top of the Front wall.

14) Insert the BLACK RB/RA pole into the hole at the end of the R1 pole and then through the eyelet at the rear of the roof and extend until the wall sits tight. Attach the Velcro strips on the rear wall.

Simple line drawing of a mechanical assembly with a central component and a vertical rod (no text or symbols)

15) Repeat with the second BLACK RA/RB pole at the front of the tent. Thread the RB pole through the outermost of the 3 holes on the BLACK R3 pole. If the roof is too tight move back one hole before threading through the eyelet in the roof, Ensure the end of the BLACK R3 pole extends out the pocket on the front wall. Attached the Velcro strips on the front wall around the pole

16) Place white "Witch Hat" washers onto pole spikes of bothe RB poles to prevent water running down during heavy rain.

Simple diagram of a red lamp on a white base with gray background (no text or symbols)

17) Insert BLACK R4 / R5 pole into the end of the R3 pole that extends through the pole sock at the front of the tent.

18) Insert the BLACK RB/RA pole into the hole at the end of the BLACK R5 pole and then through the eyelet at the end of the awning. Extend by pressing down the button clip.

19) Extend the BLACK R4/R5 pole until the awning is tight. You may need to lower the pole by moving the support poles to the side.

20) Insert the RED A1/A2 poles into the eyelets at the front corners of the awning.

21) Guy out the front awning by attaching the short guy ropes over top of awning pole spikes. Line up the guy rope with the pole spkie and the top ridgepole spike (indicated by the -- Line). Ensure the guy rope is at a 45^ angle.

3D wireframe diagram of a geometric structure with vertical and horizontal lines, no text or symbols present

22) Insert the longer RED A3/A4 pole into centre of the side of the awning. Guy out at a 45^ angle with the longer guy rope sections.

23) Peg out front valance. the bottom of the valance should sit level with the ground. The outside of the valance should align with the outside of the tent. The inside of the valance should be vertical.

24) Place rubber pole feet under support pole (BLACK RA & RC)

Simple diagram of a red object partially submerged in a gray liquid, with no text or symbols present.

CARING FOR YOUR TENT

- Never store your tent wet.

- If you must pack your tent down while still wet, hang to dry as soon as possible to prevent mildew damage.

- Remove dirt, tree sap, and bird droppings with a soft brush and warm water before packing down.

- Do not use detergents to clean your tent. This will damage the waterproofing of the tent fabric.

- When rolling up your tent ensure there is no condensation on the floor.

- If you do get mildew forming on your tent, remove the pours with warm water and a soft brush to prevent further growth.

- It is not advisable to re-coat your canvas as a precautionary measure. This will reduce the breathability and duarbility of your tent. Freedom Canvases are pre coated and will stay waterproof and breathable for many years.

- When Storing your tent over the winter, do not store directly on concrete floors.

1) Open up all windows and close all doors.

2) Remove the RED awning poles

4) Remove the BLACK Ridge poles.

5) Remove the BLUE & GREEN Eve poles.

5) Remove all pegs, clean and place in peg bag.

6) Lay tent as flat as possible and fold the awning over main body of the tent.

7) Fold both sides into the centre of the tent

8) Fold in half. Ensure the width is the same as the length of your carry bag. Adjust if necessary.

9) Expel as much air as possible by walking down the tent towards the door

10) Roll the tent from the rear towards the door. Ensure that you wipe off any condensation and dirt as you roll.

Freedom zempire Duxton