BDPM020 - Dehumidifier BEKO - Free user manual and instructions

Product Type	Dehumidifier
Model	BDPM020
Brand	Beko
Refrigerant	R290 (flammable)
Refrigerant Amount	47 g
Dehumidifying Capacity (27°C, 60% RH)	11 L/day
Dehumidifying Capacity (30°C, 80% RH)	20 L/day
Voltage / Frequency	220-240 V / 50 Hz
Rated Power Input	430 W
Rated Current Input	2.3 A
Sound Power Level (High/Low)	63 dBA / 61 dBA
Humidity Range Setting	30% - 90% (manual)
Ambient Temperature Range	5 °C - 35 °C
Dimensions (W x H x D)	290 x 500 x 250 mm
Net Weight	12.5 kg
Protection Class	Class I
Modes	Dehumidification, Fan, Clothes Drying
Timer	0-24 hours (ON/OFF)
Child Lock	Yes (long press SWING 3s)
Filter Type	Washable (vacuum or warm water)
Continuous Drainage	Yes (diameter 10 mm tube)
Water Tank Full Indication	Red light + 15 beeps
Defrost Function	Automatic (compressor off, fan high)
Compressor Delay Protection	3 minutes restart delay

Frequently Asked Questions - BDPM020 BEKO

How do I set the timer on the Beko BDPM020 dehumidifier?

To set the timer ON: When the unit is off, press the TIMER button, then keep pressing to select a delay from 0-24 hours. To set timer OFF: When the unit is running, press TIMER and select the desired shutdown time. The setting will be saved after 5 seconds.

What does the child lock function do?

The child lock disables all buttons except the child lock and power button (when on) or all buttons (when off). To activate, long press the SWING button for 3 seconds. The child lock indicator will light up.

How do I clean the filter of the dehumidifier?

Pull up the filter from the unit. Use a vacuum cleaner to gently remove dust. If very dirty, wash with warm water and mild detergent. Ensure the filter is completely dry before reinstalling.

What should I do when the water tank is full?

The tank full indicator will turn on and the unit will beep 15 times. Press any button to stop the beeping. Empty the water tank and reposition it firmly until the indicator turns off.

How do I set up continuous drainage?

Use a plastic tube (diameter 10 mm) inserted into the continuous drainage hole at the back of the unit. Route the tube through the tank side opening. Ensure the water tank is in place and the tube is straight for proper drainage.

What does the E1 error code mean?

The E1 code indicates a coil sensor short circuit or open circuit. Check if the sensor wire is loose or replace the coil sensor. If unsure, contact service personnel.

Can I use the dehumidifier in a bathroom or near water?

No, the manual warns not to operate the unit near a bath, shower, swimming pool, or in areas where water may splash. This could cause electric shock or damage.

How does the defrost function work?

When room temperature is low, the compressor stops and the fan runs at high speed to defrost the coils. The defrost indicator lights up. The unit returns to normal operation after defrosting (typically 10 minutes).

How should I store the dehumidifier when not in use?

Empty the water tank, roll up the power cord, clean the filter, and place the unit in a cool, dry place. Ensure the area is well-ventilated.

What is the minimum room size for operating the dehumidifier?

The appliance must be installed, operated, and stored in a room with a floor area larger than 4 m² to ensure proper ventilation and safety.

USER MANUAL BDPM020 BEKO

Simple line drawing of a device resembling a blender or blender with no text or symbols

BDPM020

EN - IT - SQ - SR - SL - HR - BG

CONTENTS

ENGLISH 03-29

ITALIANO 30-57

SHQIP 58-84

SRPSKI 85-111

SLOVENŠČINA 112-137

HRVATSKI 138-163

БЪЛГАРСКИ 164-193

Please read this user manual first!

Dear Customer,

Thank you for preferring a Beko product. We hope that you get the best results from your product which has been manufactured with high quality and state-of-the-art technology. Therefore, please read this entire user manual and all other accompanying documents carefully before using the product and keep it as a reference for future use. If you handover the product to someone else, give the user manual as well. Follow all warnings and information in the user manual.

Meanings of the symbols

Following symbols are used in the various section of this manual:

This symbol shows that the operation manual should be read carefully.
This symbol shows that a service personnel should be handling this equipment with reference to the installation manual.
(For R32/R290 gas type)	This symbol shows that this appliance used a flammable refrigerant. If the refrigerant is leaked and exposed to an external ignition source, there is a risk of fire.

1 Important safety and environmental instructions

Very important!

Please do not install or use your dehumidifier before you have carefully read this manual. Please keep this instruction manual for an eventual product warranty and for future reference.

Warning:

1. Do not use means to accelerate the defrosting process or to clean, other than those recommended by the manufacturer.
2. The appliance shall be stored in a room without continuously operating open flames (for example an operating gas appliance) and ignition sources (for example an operating electric heater).
3. Do not pierce or burn.
4. Be aware the refrigerants may not contain an odour.
5. Appliance shall be installed, operated and stored in a room with a floor area larger than 4 m^2 .

Warning:

Specific information regarding appliances with R290 refrigerant gas.

• Thoroughly read all of the warnings.

• When defrosting and cleaning the appliance, do not use any tools other than those recommended by the manufacturing company.
• The appliance must be placed in an area without any continuously sources of ignition (for example: open flames, gas or electrical appliances in operation).
• Do not puncture and do not burn.

- This appliance contains Y g (see rating label back of unit) of R290 refrigerant gas.

- R290 is a refrigerant gas that complies with the European directives on the environment. Do not puncture any part of the refrigerant circuit.

- If the appliance is installed, operated or stored in a nonventilated area, the room must be designed to prevent to the accumulation of refrigerant leaks resulting in a risk of fire or explosion due to ignition of the refrigerant caused by electric heaters, stoves, or other sources of ignition.

- The appliance shall be stored so as to prevent mechanical damage from occurring.

1 Important safety and environmental instructions

Warning:

• Individuals who operate or work on the refrigerant circuit must have the appropriate certification issued by an accredited organization that ensures competence in handling refrigerants according to a specific evaluation recognized by associations in the industry.
• The appliance shall be stored in a well-ventilated area where the room size corresponds to the room area as specified for operation.
• Repairs must be performed based on the recommendation from the manufacturing company. Maintenance and repairs that require the assistance of other qualified personnel must be performed under the supervision of an individual specified in the use of flammable refrigerants.
• Do not use a bad or unsuitable socket.
• Do not use machines in the following situations
  • A: Near to source of fire.
  • B: An area where oil is likely to splash.
  • C: An area exposed to direct sunlight.
  • D: An area where water is likely to splash.
  • E: Near a bath, a shower or a swimming pool.
• Never insert your fingers, rods into the air outlet. Take special care to warn children of these dangers.

1 Important safety and environmental instructions

Warning:

• Keep the unit upward while transport and storage, for the compressor locates properly.
• Before cleaning the appliance, always turn off or disconnect the power supply.
• When moving the appliance, always turn off and disconnect the power supply, and move it slowly.
• To avoid the possibility of fire disaster, the appliance shall not be covered.
• All the appliance sockets must comply with the local electric safety requirements. If necessary, please check it for the requirements.
• Young children should be supervised to ensure that they do not play with the appliance.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capacities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

1 Important safety and environmental instructions

Warning:

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
• The appliance shall be installed in accordance with national wiring regulations.
  • Details of type and rating of fuses: T, 250V AC, 2A. or 3.15A
• Recycling

This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.

1 Important safety and environmental instructions

Warning:

•GWP: R290: 3

• Contact authorized service technician for repair or maintenance of this unit.
• Do not pull, deform, or modify the power supply cord, or immerse it in water. Pulling or misuse of the power supply cord can result in damage to the unit and cause electrical shock.

• Compliance with national gas regulations shall be observed.

- Keep ventilation openings clear of obstruction.

• Any person who is involved with working on or breaking into a refrigerant circuit should hold a current valid certificate from an industry-accredited assessment authority, which authorizes their competence to handle refrigerants safely in accordance with an industry recognized assessment specification.
• Servicing shall only be performed as recommended by the equipment manufacturer. Maintenance and repair requiring the assistance of other skilled personnel shall be carried out under the supervision of the person competent in the use of flammable refrigerants.

Warning:

• Do not operate or stop the unit by inserting or pulling out Die power plug, it may cause electric shock or fire due to heat generation.
• Unplug the unit if strange sounds, smell, or smoke comes from it.

• If any parts damage, please contact the dealer or a designated repair shop;
• In case of any damage, please turn off the air switch, disconnect the power supply, and contact the dealer or a designated repair shop;

• In any case, the power cord shall be firmly grounded.

- To avoid the possibility of danger, if power cord is damaged, please turn off the air switch and disconnect the power supply. It must be replaced from the dealer or a designated repair shop.

2 General instructions

2.1 Checks to the area

Prior to beginning work on systems containing flammable refrigerants, safety checks are necessary to ensure that the risk of ignition is minimized. For repair to the refrigerating system, the following precautions shall be complied with prior to conducting work on the system.

2.2 Work procedure

Work shall be undertaken under a controlled procedure so as to minimize the risk of a flammable gas or vapor being present while the work is being performed.

2.3 General work area

All maintenance staff and others working in the local area shall be instructed on the nature of work being carried out. Work in confined spaces shall be avoided. The area around the workspace shall be sectioned off. Ensure that the conditions within the area have been made safe by control of flammable material.

2.4 Checking for presence of refrigerant

The area shall be checked with an appropriate refrigerant detector prior to and during work, to ensure the technician is aware of potentially flammable atmospheres. Ensure that the leak detection equipment being used is suitable for use with flammable refrigerants, i.e. no-sparks, adequately sealed or intrinsically safe.

2.5 Presence of fire extinguisher

If any hot work is to be conducted on the refrigeration equipment or any associated parts, appropriate fire extinguishing equipment shall be available to hand. Have a dry powder or CO_2 fire extinguisher adjacent to the charging area.

2.6 No ignition sources

No person carrying out work in relation to a refrigeration system which involves exposing any pipe work that contains or has contained flammable refrigerant shall use any sources of ignition in such a manner that it may lead to the risk of fire or explosion. All possible ignition sources, including smoking, should be kept sufficiently far away from the site of installation, repairing, removing and disposal, during which flammable refrigerant can possibly be released to the surrounding space. Prior to work taking place, the area around the equipment is to be surveyed to make sure that there are no flammable hazards or ignition risks. "No Smoking" signs shall be displayed.

2.7 Ventilated area

Ensure that the area is in the open or that it is adequately ventilated before breaking into the system or conducting any hot work. A degree of ventilation shall continue during the period that the work is carried out. The ventilation should safely disperse any released refrigerant and preferably expel it externally into the atmosphere.

2 General instructions

2.8 Checks to the refrigeration equipment

Where electrical components are being changed, they shall be fit for the purpose and to the correct specification. At all times the manufacturer's maintenance and service guidelines shall be followed. If in doubt consult the manufacturer's technical department for assistance. The following checks shall be applied to installations using flammable refrigerants: the charge size is in accordance with the room size within which the refrigerant containing parts are installed; the ventilation machinery and outlets are operating adequately and are not obstructed; if an indirect refrigerating circuit is being used, the secondary circuit shall be checked for the presence of refrigerant; marking to the equipment continues to be visible and legible. Markings and signs that are illegible shall be corrected; refrigeration pipe or components are installed in a position where they are unlikely to be exposed to any substance which may corrode refrigerant containing components, unless the components are constructed of materials which are inherently resistant to being corroded or are suitably protected against being so corroded.

2.9 Checks to electrical devices

Repair and maintenance to electrical components shall include initial safety checks and component inspection procedures. If a fault exists that could compromise safety, then no electrical supply shall be connected to the circuit until it is satisfactorily dealt with. If the fault cannot be corrected immediately but it is necessary to continue operation, an adequate temporary solution shall be used. This shall be reported to the owner of the equipment so all parties are advised.

Initial safety checks shall include: that capacitors are discharged: this shall be done in a safe manner to avoid possibility of sparking; that there no live electrical components and wiring are exposed while charging, recovering or purging the system; that there is continuity of earth bonding.

3 Repairs to sealed components

During repairs to sealed components, all electrical supplies shall be disconnected from the equipment being worked upon prior to any removal of sealed covers, etc. If it is absolutely necessary to have an electrical supply to equipment during servicing, then a permanently operating form of leak detection shall be located at the most critical point to warn of a potentially hazardous situation.

Particular attention shall be paid to the following to ensure that by working on electrical components, the casing is not altered in such a way that the level of protection is affected.

This shall include damage to cables, excessive number of connections, terminals not made to original specification, damage to seals, incorrect fitting of glands, etc. Ensure that apparatus is mounted securely. Ensure that seals or sealing materials have not degraded such that they no longer serve the purpose of preventing the ingress of flammable atmospheres. Replacement parts shall be in accordance with the manufacturer's specifications.

The use of silicon sealant may inhibit the effectiveness of some types of leak detection equipment. Intrinsically safe components do not have to be isolated prior to working on them.

3.1 Repair to intrinsically safe components

Do not apply any permanent inductive or capacitance loads to the circuit without ensuring that this will not exceed the permissible voltage and current permitted for the equipment in use.

Intrinsically safe components are the only types that can be worked on while live in the presence of a flammable atmosphere. The test apparatus shall be at the correct rating. Replace components only with parts specified by the manufacturer. Other parts may result in the ignition of refrigerant in the atmosphere from a leak.

3.2 Cabling

Check that cabling will not be subject to wear, corrosion, excessive pressure, vibration, sharp edges or any other adverse environmental effects. The check shall also take into account the effects of aging or continual vibration from sources such as compressors or fans.

3.3 Detection of flammable refrigerants

Under no circumstances shall potential sources of ignition be used in the searching for or detection of refrigerant leaks. A halide torch (or any other detector using a naked flame) shall not be used.

3 Repairs to sealed components

3.4 Leak detection methods

The following leak detection methods are deemed acceptable for systems containing flammable refrigerants. Electronic leak detectors shall be used to detect flammable refrigerants, but the sensitivity may not be adequate, or may need recalibration. (Detection equipment shall be calibrated in a refrigerant-free area.) Ensure that the detector is not a potential source of ignition and is suitable for the refrigerant used. Leak detection equipment shall be set at a percentage of the LFL of the refrigerant and shall be calibrated to the refrigerant employed and the appropriate percentage of gas (25 % maximum) is confirmed. Leak detection fluids are suitable for use with most refrigerants but the use of detergents containing chlorine shall be avoided as the chlorine may react with the refrigerant and corrode the copper pipework. If a leak is suspected, all naked flames shall be removed/extinguished. If a leakage of refrigerant is found which requires brazing, all of the refrigerant shall be recovered from the system, or isolated (by means of shut off valves) in a part of the system remote from the leak. Oxygen free nitrogen (OFN) shall then be purged through the system both before and during the brazing process.

3.5 Removal and evacuation

When breaking into the refrigerant circuit to make repairs – or for any other purpose – conventional procedures shall be used. However, it is important that best practice is followed since flammability is a consideration. The following procedure shall be adhered to: remove refrigerant; purge the circuit with inert gas; evacuate; purge again with inert gas; open the circuit by cutting or brazing. The refrigerant charge shall be recovered into the correct recovery cylinders. The system shall be “flushed” with OFN to render the unit safe. This process may need to be repeated several times. Compressed air or oxygen shall not be used for this task. Flushing shall be achieved by breaking the vacuum in the system with OFN and continuing to fill until the working pressure is achieved, then venting to atmosphere, and finally pulling down to a vacuum. This process shall be repeated until no refrigerant is within the system. When the final OFN charge is used, the system shall be vented down to atmospheric pressure to enable work to take place. This operation is absolutely vital if brazing operations on the pipework are to take place.

Ensure that the outlet for the vacuum pump is not close to any ignition sources and there is ventilation available.

3 Repairs to sealed components

3.6 Charging procedures

In addition to conventional charging procedures, the following requirements shall be followed.

• Ensure that contamination of different refrigerants does not occur when using charging equipment. Hoses or lines shall be as short as possible to minimise the amount of refrigerant contained in them.
• Cylinders shall be kept upright.
• Ensure that the refrigeration system is earthed prior to charging the system with refrigerant.
• Label the system when charging is complete (if not already).
• Extreme care shall be taken not to overfill the refrigeration system.

Prior to recharging the system it shall be pressure tested with OFN. The system shall be leak tested on completion of charging but prior to commissioning. A follow up leak test shall be carried out prior to leaving the site.

3.7 Decommissioning

Before carrying out this procedure, it is essential that the technician is completely familiar with the equipment and all its detail. It is recommended good practice that all refrigerants are recovered safely. Prior to the task being carried out, an oil and refrigerant sample shall be taken in case analysis is required prior to re-use of reclaimed refrigerant. It is essential that electrical power is available before the task is commenced.

• Become familiar with the equipment and its operation.
• Isolate system electrically.
• Before attempting the procedure ensure that: mechanical handling equipment is available, if required, for handling refrigerant cylinders; all personal protective equipment is available and being used correctly; the recovery process is supervised at all times by a competent person; recovery equipment and cylinders conform to the appropriate standards.
• Pump down refrigerant system, if possible.
• If a vacuum is not possible, make a manifold so that refrigerant can be removed from various parts of the system.
• Make sure that cylinder is situated on the scales before recovery takes place.
• Start the recovery machine and operate in accordance with manufacturer's instructions.
• Do not overfill cylinders. (No more than 80% volume liquid charge).
• Do not exceed the maximum working pressure of the cylinder, even temporarily.
• When the cylinders have been filled correctly and the process completed, make sure that the cylinders and the equipment are removed from site promptly and all isolation valves on the equipment are closed off.
• Recovered refrigerant shall not be charged into another refrigeration system unless it has been cleaned and checked.

3 Repairs to sealed components

3.8 Labelling

Equipment shall be labelled stating that it has been de-commissioned and emptied of refrigerant. The label shall be dated and signed.

Ensure that there are labels on the equipment stating the equipment contains flammable refrigerant.

3.9 Recovery

When removing refrigerant from a system, either for servicing or decommissioning, it is recommended good practice that all refrigerants are removed safely. When transferring refrigerant into cylinders, ensure that only appropriate refrigerant recovery cylinders are employed. Ensure that the correct number of cylinders for holding the total system charge are available. All cylinders to be used are designated for the recovered refrigerant and labelled for that refrigerant (i.e. special cylinders for the recovery of refrigerant). Cylinders shall be complete with pressure relief valve and associated shut-off valves in good working order. Empty recovery cylinders are evacuated and, if possible, cooled before recovery occurs.

The recovery equipment shall be in good working order with a set of instructions concerning the equipment that is at hand and shall be suitable for the recovery of flammable refrigerants. In addition, a set of calibrated weighing scales shall be available and in good working order. Hoses shall be complete with leak-free disconnect couplings and in good condition.

Before using the recovery machine, check that it is in satisfactory working order, has been properly maintained and that any associated electrical components are sealed to prevent ignition in the event of a refrigerant release. Consult manufacturer if in doubt.

The recovered refrigerant shall be returned to the refrigerant supplier in the correct recovery cylinder, and the relevant Waste Transfer Note arranged. Do not mix refrigerants in recovery units and especially not in cylinders.

If compressors or compressor oils are to be removed, ensure that they have been evacuated to an acceptable level to make certain that flammable refrigerant does not remain within the lubricant. The evacuation process shall be carried out prior to returning the compressor to the suppliers. Only electric heating to the compressor body shall be employed to accelerate this process. When oil is drained from a system, it shall be carried out safely.

3.10 Competence of service personnel

3.10.1 General

Special training additional to usual refrigerating equipment repair procedures is required when equipment with flammable refrigerants is affected.

In many countries, this training is carried out by national training organisations that are accredited to teach the relevant national competency standards that may be set in legislation.

3 Repairs to sealed components

The achieved competence should be documented by a certificate.

3.10.2 Training

The training should include the substance of the following:

Information about the explosion potential of flammable refrigerants to show that flammables may be dangerous when handled without care.

Information about potential ignition sources, especially those that are not obvious, such as lighters, light switches, vacuum cleaners, electric heaters.

Information about the different safety concepts:

Unventilated – (see Clause GG.2) Safety of the appliance does not depend on ventilation of the housing. Switching off the appliance or opening of the housing has no significant effect on the safety. Nevertheless, it is possible that leaking refrigerant may accumulate inside the enclosure and flammable atmosphere will be released when the enclosure is opened.

Ventilated enclosure – (see Clause GG.4) Safety of the appliance depends on ventilation of the housing. Switching off the appliance or opening of the enclosure has a significant effect on the safety. Care should be taken to ensure a sufficient ventilation before.

Ventilated room – (see Clause GG.5) Safety of the appliance depends on the ventilation of the room. Switching off the appliance or opening of the housing has no significant effect on the safety. The ventilation of the room shall not be switched off during repair procedures.

Information about the concept of sealed components and sealed enclosures according to IEC 60079-15:2010.

Information about the correct working procedures:

Commissioning

• Ensure that the floor area is sufficient for the refrigerant charge or that the ventilation duct is assembled in a correct manner.
• Connect the pipes and carry out a leak test before charging with refrigerant.
• Check safety equipment before putting into service.

Maintenance

- Portable equipment shall be repaired outside or in a workshop specially equipped for servicing units with flammable refrigerants.

- Ensure sufficient ventilation at the repair place.

- Be aware that malfunction of the equipment may be caused by refrigerant loss and a refrigerant leak is possible.

- Discharge capacitors in a way that won't cause any spark. The standard procedure to short circuit the capacitor terminals usually creates sparks.

- Reassemble sealed enclosures accurately. If seals are worn, replace them.

- Check safety equipment before putting into service.

3 Repairs to sealed components

Repair

- Portable equipment shall be repaired outside or in a workshop specially equipped for servicing units with flammable refrigerants.

- Ensure sufficient ventilation at the repair place.

- Be aware that malfunction of the equipment may be caused by refrigerant loss and a refrigerant leak is possible.

- Discharge capacitors in a way that won't cause any spark.

- When brazing is required, the following procedures shall be carried out in the right order:

- Remove the refrigerant. If the recovery is not required by national regulations, drain the refrigerant to the outside. Take care that the drained refrigerant will not cause any danger. In doubt, one person should guard the outlet. Take special care that drained refrigerant will not float back into the building.

• Evacuate the refrigerant circuit.

- Purge the refrigerant circuit with nitrogen for 5 min.

- Evacuate again.

- Remove parts to be replaced by cutting, not by flame.

- Purge the braze point with nitrogen during the brazing procedure.

- Carry out a leak test before charging with refrigerant.

- Reassemble sealed enclosures accurately. If seals are worn, replace them.

- Check safety equipment before putting into service.

Decommissioning

- If the safety is affected when the equipment is put out of service, the refrigerant charge shall be removed before decommissioning.

- Ensure sufficient ventilation at the equipment location.

- Be aware that malfunction of the equipment may be caused by refrigerant loss and a refrigerant leak is possible.

- Discharge capacitors in a way that won't cause any spark.

- Remove the refrigerant. If the recovery is not required by national regulations, drain the refrigerant to the outside. Take care that the drained refrigerant will not cause any danger. In doubt, one person should guard the outlet. Take special care that drained refrigerant will not float back into the building.

• Evacuate the refrigerant circuit.

- Purge the refrigerant circuit with nitrogen for 5 min.

- Evacuate again.

- Fill with nitrogen up to atmospheric pressure.

- Put a label on the equipment that the refrigerant is removed.

Disposal

- Ensure sufficient ventilation at the working place.

- Remove the refrigerant. If the recovery is not required by national regulations, drain the refrigerant to the outside. Take care that the drained refrigerant will not cause any danger. In doubt, one person should guard the outlet. Take special care that drained refrigerant will not float back into the building.

• Evacuate the refrigerant circuit.

3 Repairs to sealed components

• Purge the refrigerant circuit with nitrogen for 5 min.
• Evacuate again.
• Cut out the compressor and drain the oil.

Transportation, marking and storage for units that employ flammable refrigerants

Transport of equipment containing flammable refrigerants.

Attention is drawn to the fact that additional transportation regulations may exist with respect to equipment containing flammable gas. The maximum number of pieces of equipment or the configuration of the equipment, permitted to be transported together will be determined by the applicable transport regulations.

Marking of equipment using signs

Signs for similar appliances used in a work area generally are addressed by local regulations and give the minimum requirements for the provision of safety and/or health signs for a work location.

All required signs are to be maintained and employers should ensure that employees receive suitable and sufficient instruction and training on the meaning of appropriate safety signs and the actions that need to be taken in connection with these signs.

The effectiveness of signs should not be diminished by too many signs being placed together.

Any pictograms used should be as simple as possible and contain only essential details.

Disposal of equipment using flammable refrigerants

See national regulations.

Storage of equipment/appliances

The storage of equipment should be in accordance with the manufacturer's instructions.

Storage of packed (unsold) equipment

Storage package protection should be constructed such that mechanical damage to the equipment inside the package will not cause a leak of the refrigerant charge.

The maximum number of pieces of equipment permitted to be stored together will be determined by local regulations.

General Safety Instruction

Warning:

Before you use the machine, please read the instructions carefully so that you can maximize the use of all the features of the machine. This instruction is for guidance only and is not part of the contract, we reserve the right to make technical changes and we will not notify you before the amendment.

3 Repairs to sealed components

Notice before use:

1. "PLEASE MAKE SURE THE PRODUCT VENTILATES ALL THE TIME"! Please make sure the inlet and outlet ventilation is not blocked at all times.
2. Operate this unit on a horizontal surface to avoid water leakage.
3. Do not operate this unit in an explosive or corrosive atmosphere.
4. Machine working environment temperature: cooling at 5 °C - 35 °C.
5. When the unit is shut off, please wait at least 3 minutes before restarting this is to prevent the compressor from being damaged.
6. Use separate power supply, prohibit the sharing of a socket with other electrical appliances, Power outlet specifications should not be less than 10A, sockets must be firmly safe.
7. Power: 220-240V/50hz.
8. Discard water that has collected in the tank as required.
9. Do not submerge the unit in water, or place the unit close to water.
10. Do not sit or stand on the unit.
11. Do not operate the dehumidifier in a closed area such as inside a closet, as it may cause a fire.
12. Install drain piping at a downhill grade to make sure that condensed water can be drained continuously.

4 Part figure

2.1 Control and parts

1. Supply cord
2. Tank
3. Continuous drainage/Power cable collection
4. Filter screen
5. Back shell
6. Air outlet
7. Top cover
8. Front shell
9. Water indicator

2.2 Specifications

Model name BDPM020
Refrigerant R290
Total Refrigerant Amount (g) 47
Protection against electric shock Class I
Rated Dehumidifying Capacity (27°C RH60%) (L/day) 11
Rated Dehumidifying Capacity (30°C RH80%) (L/day) 20
Voltage/Frequency/Phase (V/Hz/Phase) 220V-240V / 50Hz
Sound Power Level (dBA) 63/61
Rated Power Input (W) 430
Rated Current Input (A) 2.3
RH Range Manual 30%-90%
Ambient temp 5-35
Unit Net Dimension (WxHxD) mm 290x500x250
Unit Net Weight (kg) 12.5

5 Operating instructions

Power button:

Press the power button to turn on the appliance. The air outlet cover opens automatically.

Press the button again to turn off the appliance. The air outlet cover closes automatically.

After startup, the current humidity is displayed; The humidity first defaults to "Co" and the compressor is allowed to start immediately to begin dehumidification.

SPEED button:

Press the fan speed button to select low or high fan speed. The corresponding indicator light will illuminate.

ADJUST button:

Press the ADJUST button, the indicator light of "Co" illuminates. When the humidity is set, the humidity is set as follows: "Co" (continuous) -80% 35% →40% 45% 50...... 85 90 → → → "Co" (continuous) cycle.

The setting will be in effect in approx. 5 seconds with no further operations. The digital display will turn back to show the room humidity.

Timer button

Timer ON setting:

• When the appliance is off, press the button "TIMER", the corresponding indicator light will illuminate.
• Keep pressing the button "TIMER" to select a desired ON time from 0-24 hours. The setting will be in effect in approx. 5 seconds with no further operations.
• The appliance will automatically turn on once the set time has passed.

Timer OFF setting:

• When the appliance is working, press the button "TIMER", the corresponding indicator light will illuminate.
• Keep pressing the button "TIMER" to select a desired OFF time from 0-24 hours. The setting will be in effect in approx. 5 seconds with no further operations. The digital display will turn back to show the humidity level.
• The appliance will automatically turn off once the set time has passed.

Mode button

Press the mode button to select your desired mode: dehumidification mode, fan mode or clothes drying mode.

5 Operating instructions

SWING button

Press the swing button to turn on/off the swing function of the air outlet cover.

Lock: Long press the SWING button for 3 seconds to select the child lock;

• In the state of power on: After the child lock is turned on, all the buttons except the child lock and the power button cannot be operated (Note: the power button can be shut down).
• In the off state: the child lock function can be opened and closed. After the child lock is opened, all other key operations except the child lock button cannot be operated (note: the power button cannot be operated either).
• After opening the child lock function, the child lock indicator lights up.

The water full light is red, the double 8 screen on the display board is white, and the other indicator lights are white.

After 20 seconds of operation, all indicator lights (including double 8) will be dimmed.

5.1 Description of functions

Dehumidification function:

1. When the "Co" (continuous) dehumidification operation is set, the dehumidifier will continue to run (compressor, fan operation) regardless of the humidity level at that time.

2. If the indoor humidity is higher than or equal to 3% of the set humidity, the compressor will start to run dehumidification, and the compressor and fan will run.

3. After the indoor humidity is dehumidified, when the humidity drops below 2% of the set humidity, the compression mechanism will stop the dehumidification, the compressor will enter the protection for three minutes, and the fan will stop after 3 minutes.

4. If the indoor humidity rises to 3% higher than or equal to the set humidity after the dehumidifier stops dehumidification, if the compressor has passed the protection state for three minutes, the compressor will start to run dehumidification.
5. According to the above cycle operation, the indoor humidity can be maintained at about the set humidity.

Clothes drying function:

1. When this function is enabled, the de-humidifier will run continuously (compressor and fan run) no matter the humidity is high or low when "Co" (continuous) operation is carried out.
2. The wind speed is locked to high speed and cannot be adjusted.
3. Humidity setting button is not adjustable.

FAN function:

1. The compressor does not work.
2. The fan can be operated in two modes: high wind and low wind.
3. Humidity setting button is not adjustable in air supply mode.

5 Operating instructions

Full water protection function:

1. When the water tank is full, the Tank Full Indicator (FULL) light will turn on, the Dehumidifier will stop running automatically and the buzzer will beep 15 times.
2. Press any button to stop the buzzer. The compressor and fan will shut down and
3. all functions will not working until the Water Tank has been emptied and replaced.

Defrosting function:

1. When defrosting, the compressor is shut down, the fan keeps running as high speed for defrosting, and the defrosting indicator light is always on.
2. When the room temperature is less than or equal to 16^ C, the coil temperature will not be detected. According to the action of room temperature, the details are as follows:
3. When the room temperature ≤12^ , the compressor runs for 30 minutes, shutdown defrosting for 10 minutes, and then return to the setting mode before defrosting.
4. When 12^ C < room temperature ≤ 16^ C, the compressor will run for 45 minutes and stop for defrosting for 10 minutes, and then return to the setting mode before defrosting.
5. When the room temperature is greater than 16^ C, According to the coil temperature action, the details are as follows: When the compressor runs for 30 minutes, if the coil temperature is less than 1, stop the machine to de-

frost for 10 minutes, and then return to the setting mode before defrosting.

During defrosting, the defrosting light is always on.

Compressor delay protection:

1. The compressor is allowed to start immediately each time it is started;
2. After the compressor stops, start again, there should be an interval of at least 3 minutes.

Water tank drain

When the drainage tank is full, the tank full indicator light will turn on, the operation will stop automatically and the buzzer will beep 15 times to alert the user, that the water need to be emptied from the drainage tank.

Empty tank

1. Gently press on the sides of the tank and pull the tank out with both hands.

Line drawing of a portable air conditioner unit with red arrows indicating airflow or movement (no text or symbols)

5 Operating instructions

1. Empty the water in the tank.

Technical line drawing of a mechanical assembly with a water droplet symbol (no text or labels)

1. Do not remove the floater in the water tank, otherwise, the water sensor will not be able to sense the water level so that it can not operate normally.

Technical line drawing of a mechanical housing or enclosure component (no text or symbols)

1. If the tank is dirty, use cold water or warm water cleaning. It is not possible to use detergents, steel velvet, chemical treated dusting cloth, gasoline, benzene, thinner or other solvents, because it may damage the water tank and cause water leakage.

2. When putting into the tank, press the tank tightly with both hands. If the water tank is not placed, the full water sensor will still be activated, and the dehumidifier will not work.

Line drawing of a portable air conditioner unit with red arrows indicating airflow or cooling direction (no text or symbols)

5 Operating instructions

Continuous drainage

The dehumidifier has a continuous drainage hole, using a plastic tube (diameter 10mm) inserted in partition drainage hole, then outgoing from the tank side. When the water tank should be installed in place, and the drainage pipe straightened out, the water can be drained from the machine through the drainage hole.

Line drawing of a portable air purifier with attached cable and outlet (no text or symbols)

6 Maintenance

6.1 Body cleaning

wipe the body with a soft, damp cloth.

6.2 Filter cleaning

1. Pull up the filter.

Line drawing of a portable air purifier with open lid and ventilation slots, showing red directional arrows indicating airflow or movement (no text or symbols)

1. Clean Filter

Use a vacuum cleaner to gently absorb dust on filter screen surface. If very dirty, use warm water and gentle detergent. Keep dry.

Diagram of a rectangular device with a grid pattern and a spray gun above it (no text or symbols)

1. Filter Installation

Insert the filter into the machine, and push the two hooks of the filter in place.

Line drawing of a portable air purifier with ventilation slots and a lid, showing airflow direction (no text or symbols)

6.3 Dehumidifier storage

When you do not use this product for a long time and intend to store it, pay attention to the following steps

Empty the water in the tank.

Roll up the power cord.

Cleaning strainer.

Place in a cool and dry place.

Line drawing of a portable air purifier with control panel and power cord (no text or symbols)

6 Maintenance

6.4 Space distance

When the dehumidifier is working, make sure that the minimum distance between them is as shown in the following picture.

7 Troubleshooting

If a condition listed below occurs, please check the following items before calling customer service.

Problem Possible Cause Solution
The unit doesn't operate	Has the power cord been disconnected?	Plug the power cord into the outlet.
	Is the tank full indication lamp blinking? (The tank is full or in a wrong position.)	Empty the water in the water tank and then re-position the tank.
	Is the temperature of the room above 35 °C or below 5 °C?	The protection device is activated and the unit cannot be started.
The dehumidifying function doesn't work	Is the air filter clogged?	Clean the air filter as instructed under “Cleaning the dehumidifier”.
	Is the intake duct or discharge duct obstructed?	Remove the obstruction from the discharge duct or intake duct.
No air is discharged Is the air filter clogged?		Clean the air filter as instructed under “Cleaning the dehumidifier”.
Operation is noisy	Is the unit tilted or un-steady?	Move the unit to a stable, sturdy location.
	Is the air filter clogged?	Clean the air filter as instructed under “Cleaning the dehumidifier”.
E1 Code	Coil sensor short circuit or open circuit	Check whether the line is loose or replace the coil sensor.

8 Installation instructions

8.1 F-Gas instruction

This product contains fluorinated greenhouse gases.

The fluorinated greenhouse gases are contained in hermetically sealed equipment.

Installs, services, maintains, repairs, checks for leaks or decommissions equipment and product recycling should be carried out by natural persons that hold relevant certificates.

If the system has a leakage detection system installed, leakage checks should be performed at least every 12 months, make sure system operate properly.

If product must be performed leakage checks, it should specify Inspection cycle, establish and save records of leakage checks.

For hermetically sealed equipment, local air conditioner, window air conditioner and dehumidifier, if CO2 equivalent of fluorinated greenhouse gases is less than 10 tonnes, it should not perform leakage checks.

2.1 Comandi e parti

Line drawing of a portable air purifier with red arrows indicating airflow or ventilation direction (no text or symbols)

Technical line drawing of a mechanical or architectural component with no visible text or symbols

Technical line drawing of a mechanical housing or enclosure with internal components and mounting brackets (no text or symbols)

Line drawing of a portable kitchen appliance with red arrows indicating airflow or movement (no text or symbols)

Drenaggio continuo

Line drawing of a portable air purifier with attached cable and control panel (no text or symbols)

6 Manutenzione

Line drawing of a portable air purifier with ventilation slots and a door, showing red directional arrows indicating airflow or movement (no text or symbols present)

1. Pulire il filtro

Diagram of a rectangular container with a grid pattern and a spray gun above it (no text or symbols)

Line drawing of a portable air purifier with ventilation grilles and cooling unit, showing airflow direction (no text or symbols)

Line drawing of a portable air purifier with control panel and power outlet (no text or symbols)

6 Manutenzione

6.4 Distanza

Line drawing of a portable air purifier with red arrows indicating airflow direction (no text or symbols)

Technical line drawing of a mechanical assembly with no visible text or symbols

Technical line drawing of a mechanical housing or enclosure with internal components and mounting brackets (no text or symbols)

Line drawing of a portable kitchen appliance with red arrows indicating airflow or movement (no text or symbols)

Line drawing of a portable air purifier with attached cable and power outlet (no text or symbols)

Line drawing of a portable air purifier with ventilation slots and a door, showing red directional arrows indicating airflow or movement (no text or symbols)

1. Pastroni filtrin

Diagram of a rectangular device with a grid pattern and a spray gun above it (no text or symbols)

1. Instalimi i filtrit

Line drawing of a portable air purifier with ventilation slots and a lid, showing airflow direction (no text or symbols)

Line drawing of a portable industrial water heater with control panel and power outlet (no text or symbols)

2.1 Kontrole i delovi

1. Kabal za napajanje
2. Rezervoar
3. Kontinuirano odvodnjavanje/sakupljanje kablova za napajanje
4. Filter ekran
5. Zadnji oklop
6. Izlaz za vazduh
7. Gornji poklopac
8. Prednji oklop
9. Indikator vode

4 Slike delova

2.2 Specifikacije

Naziv modela BDPM020
Rashladno sredstvo R290
Ukupna količina rashladnog sredstva (g) 47
Zaštita od strujnog udara Klasa I
Nominalni kapacitet odvlaživanja (27°C RH60%) (L/dan)	11
Nominalni kapacitet odvlaživanja (30°C RH80%) (L/dan)	20
Napon/Frekvencija/Faza (V/Hz/Faza) 220V-240V / 50Hz
Nivo zvučne snage (dBA) 63/61
Nominalni ulaz snage (W) 430
Nominalni ulaz struje (A) 2,3
Raspon relativne vlažnosti vazduha ručno 30%-90%
Ambijentalna temperatura 5-35
Neto dimenzije uređaja (ŠxVxD) mm 290x500x250
Neto težina jedinice (kg) 12,5

5 Uputstva za rad

Dugme za napajanje:

Pritisnite dugme za uključivanje da biste uključili uređaj. Poklopac izlaza vazduha se automatski otvara.

Ponovno pritisnite dugme da biste isključili uređaj. Poklopac izlaza vazduha se automatski zatvara.

Nakon pokretanja, prikazuje se trenutna vlažnost; Vlažnost je prvobitno podešena na „Co“ i kompresoru je dozvoljeno da se odmah pokrene kako bi započeo odvlaživanje.

Line drawing of a portable air purifier with red arrows indicating airflow direction (no text or symbols)

Technical line drawing of a mechanical assembly with a water droplet symbol (no text or labels)

Technical line drawing of a mechanical housing or enclosure with internal components and mounting brackets (no text or symbols)

5 Uputstva za rad

Line drawing of a refrigerator with open door and red arrows indicating airflow or movement (no text or symbols)

Kontinuirano pražnjenje

Line drawing of a portable air purifier with attached cable and control panel (no text or symbols)

6 Održavanje

Line drawing of a portable air purifier with ventilation slots and a door, showing red directional arrows indicating airflow or movement (no text or symbols present)

1. Čišćenje filtera

Koristite usisivač da nežno usisate prašinu sa površine filtera. Ako je veoma prljav, koristite toplu vodu i blagi deterdžent. Čuvati na suvom mestu.

Diagram of a rectangular device with a grid pattern and a spray gun above it (no text or symbols)

1. Ugradnja filtera

Ubacite filter u uređaj i gurnite dve kuke filtera na mesto.

Line drawing of a portable air purifier with cooling fins and ventilation slots, showing airflow direction (no text or symbols)

Line drawing of a portable industrial water heater with control panel and power outlet (no text or symbols)

6 Održavanje

6.4 Prostorni razmak

2.1 Upravljanje in deli

Line drawing of a portable air conditioner unit with red arrows indicating airflow or movement (no text or symbols)

Technical line drawing of a mechanical assembly with a water droplet symbol (no text or labels)

1. Ne odstranite plovca v rezervoarju za vodo, sicer vodni senzor ne bo mogel zaznati nivoja vode, zato ne bo mogel normalno de- lovati.

Technical line drawing of a mechanical housing or enclosure with internal components and mounting brackets (no text or symbols)

Line drawing of a portable refrigerator with red arrows indicating airflow or movement (no text or symbols)

Line drawing of a portable air purifier with attached cable and outlet (no text or symbols)

6 Vzdrževanje

6.1 Čiščenje telesa

telo obrišite z mehko in vlažno krpo.

6.2 Čiščenje filtra

1. Dvignite filter.

Line drawing of a portable air purifier with open lid and ventilation slots, showing red directional arrows indicating airflow or movement (no text or symbols)

1. Čisti filter

S sesalnikom nežno posesajte prah na površini filtracijskega zaslona. Če je zelo umazan, uporabite toplo vodo in nežen detergent. Hranite na suhem.

Diagram of a rectangular device with a grid pattern and a spray gun above it (no text or symbols)

1. Namestitev filtra

Vstavite filter v stroj in potisnite dva kaveljčka filtra na mesto.

Line drawing of a portable air purifier with ventilation slots and a lid, showing airflow direction (no text or symbols)

6.3 Shranjevanje izsuševalnika zraka

Line drawing of a portable industrial water heater with control panel and power outlet (no text or symbols)

6 Vzdrževanje

6.4 Prostorska razdalja

Line drawing of a portable air purifier with red arrows indicating airflow direction (no text or symbols)

Technical line drawing of a mechanical assembly with no visible text or symbols

5 Upute za rukovanje

1. Ako je spremnik prljav, za čišćenje koristite hladnu ili toplu vodu. Ne smiju se koristiti deterdženti, žičane spužvice, kemijski tretirane krpe za prašinu, benzin, benzen, razrjeđivač ili druga otapala jer mogu oštetiti spremnik za vodu i izazvati curenje vode.
2. Kada vraćate spremnik na njegovo mjesto, čvrsto pritisnite spremnik s obje ruke. Ako spremnik za vodu nije postavljen, senzor napunjenosti vode će i dalje biti aktiviran, a odvlaživač zraka neće raditi.

Line drawing of a refrigerator with open door and red arrows indicating airflow or movement (no text or symbols)

Line drawing of a portable air purifier with attached cable and control panel (no text or symbols)

6 Održavanje

Line drawing of a portable air purifier with ventilation slots and a door, showing red directional arrows indicating airflow or movement (no text or symbols)

1. Čišćenje filtra

Diagram of a rectangular device with a grid pattern and a spray gun above it (no text or symbols)

1. Ugradnja filtra

Line drawing of a portable air purifier with cooling fins and ventilation slots, showing airflow direction (no text or symbols)

Line drawing of a portable industrial water heater with control panel and power outlet (no text or symbols)

6 Održavanje

6.4 Razmak

Kada odvlaživač radi, provjerite je li minimalna udaljenost poput one prikazane na sljedećoj slici.

7 Rješavanje problema

Ako se dogodi stanje navedeno u nastavku, provjerite sljedeće stavke prije nego što nazovete korisničku podršku.

Problem Mogući uzrok Rješenje
Uređaj ne radi	Je li napajanje odspoje-no?	Ukopčajte strujni kabel u zidnu strujnu utičnicu.
	Treperi li svjetlo pokaza-telja napunjenosti spre-mnika? (Spremnik je pun ili u krivom položaju.)	Ispraznite vodu iz spre-mnika za vodu i ponov-no stavite spremnik na njegovo mjesto.
	Je li temperatura sobe iznad 35 °C ili ispod 5 °C?	Zaštitni uređaj je aktiviran i uređaj se ne može pokrenuti.
Funkcija odvlaživanja ne radi.	Je li filtar zraka zače-pljen?	Očistite filtar zraka prema uputama u dijelu „Čišće-nje odvlaživača“.
	Je li dovodna ili odvodna cijev začepljena?	Uklonite prepreke iz do-vodne ili odvodne cijevi.
Zrak se ne ispušta	Je li filtar zraka zače-pljen?	Očistite filtar zraka prema uputama u dijelu „Čišće-nje odvlaživača“.
Bučan rad	Je li uređaj nagnut ili nestabilan?	Pomaknite uređaj na sta-bilno, čvrsto mjesto.
	Je li filtar zraka zače-pljen?	Očistite filtar zraka prema uputama u dijelu „Čišće-nje odvlaživača“.
E1 šifra	Kratki spoj ili otvoreni krug senzora zavojnice	Provjerite je li vod labav ili zamijenite senzor zavojnice.

8 Upute za instalaciju

8.1 Upute za F-plin

Ovaj proizvod sadrži fluorirane stakleničke plinove.

Fluorirani staklenički plinovi nalaze se u hermetički zatvorenoj opremi.

Instalacije, servisiranje, održavanje, po-pravke, provjere curenja ili oprema povu-čena iz upotrebe i recikliranje proizvoda trebaju provoditi fizičke osobe koje posjeduju odgovarajuće certifikate.

Warning symbol of a flame inside a triangle (no text or numbers)

2.1 Контролни механизми и части

Line drawing of a portable air conditioner unit with red directional arrows indicating airflow or movement (no text or symbols)

Technical line drawing of a mechanical assembly with no visible text or symbols

Technical line drawing of a mechanical housing or enclosure with internal components and mounting brackets (no text or symbols)

5 Инструкции за експлоатация

Line drawing of a portable air conditioner unit with red arrows indicating airflow or movement (no text or symbols)

Непрекъснат дренаж

Line drawing of a portable air purifier with attached cable and control panel (no text or symbols)

6 Поддръжка

Line drawing of a portable air purifier with ventilation slots and a door, showing red directional arrows indicating airflow or movement (no text or symbols)

1. Почистете филтъра

Diagram of a rectangular device with a grid pattern and a spray gun above it (no text or symbols)

1. Монтаж на филтър

Line drawing of a portable air purifier with lid removed and red arrows indicating airflow direction (no text or symbols)

Line drawing of a portable air purifier with control panel and power cord (no text or symbols)

6 Поддръжка