Croper MG10N - Scissors Eldom - Free user manual and instructions

Product Type	Hair Clipper
Model	Croper MG10N
Brand	Eldom
Power Supply	230 V ~ 50 Hz, 3 W
Battery Type	Ni-Cd, 900 mAh
Charging Time	Approx. 8 hours
Cutting Length Range	0.8 mm - 2 mm (without comb); with comb attachments: 3 mm, 6 mm, 9 mm, 12 mm; 25 adjustable lengths
Comb Attachments Included	4 combs: 3 mm, 6 mm, 9 mm, 12 mm
Cutting Head	Removable and replaceable
Blade Material	Stainless steel (assumed)
Cleaning Accessories	Cleaning brush, maintenance oil
Usage	For dry hair only; not for animal or artificial hair
Safety Features	Do not use near water; disconnect after use; check cord regularly
Warranty	For domestic use only; professional use voids warranty
Disposal	Electric and electronic equipment recycling

Frequently Asked Questions - Croper MG10N Eldom

How do I charge the Croper MG10N hair clipper?

Turn off the device (switch to '0'), plug the feeder into the clipper's charging port and connect to the mains. The red control lamp will light up during charging. Charging time is approximately 8 hours.

Can I use the hair clipper while charging?

Yes, the clipper can be used with the power cord connected, or it can run on the battery after charging. When used corded, turn the switch to '1' after connecting.

How do I adjust the cutting length?

Use the rotating ring on the cutting head for precise adjustment from 0.8 mm to 2 mm. For longer lengths, attach one of the 4 comb heads (3, 6, 9, or 12 mm). The combination offers 25 different length settings.

How do I remove and attach the comb head?

To attach, slide the comb head into the side grooves of the cutting head. To remove, press the 'PUSH' area on the comb head and slide it off in the indicated direction.

Can I use the clipper on wet hair?

No, the clipper is designed for dry hair only. Using it on wet hair may damage the device or cause injury.

How do I clean the clipper after use?

Turn off and unplug the device. Open the cutting head by pressing the blades with your thumb (as shown in the manual). Use the included brush to clean the blades. Wipe the casing with a damp or dry cloth. Do not immerse in water.

How often should I oil the blades?

Regularly, after each use or at least once a week. Apply 1-2 drops of the included maintenance oil between the blades and run the clipper for a few seconds.

What does the red control lamp indicate?

The red lamp lights up when the clipper is connected to power, indicating that the device is being powered or charged. It does not turn off after the battery is fully charged.

Can I replace the battery?

The battery is built-in and not user-replaceable. For battery issues, contact an authorized service center. The battery is Ni-Cd, 900 mAh.

Is the clipper suitable for professional use?

No, it is intended for domestic (household) use only. Professional use may void the warranty.

USER MANUAL Croper MG10N Eldom

Close-up of a red and black hairless electric shaver with a white head and black handle (no text or symbols visible)

Eldom Sp. z o.o.

fot. 1

OPIS ZESTAWU

Close-up of a hair styling tool with black and white teeth, showing a 2.0mm mark (no text or symbols on the tool itself)

fot. 2

Close-up of a hairpin with an orange arrow indicating the cutting edge (no text or symbols visible)

fot. 3

CZYSZCZENIE I KONSERWACJA

• Before using the appliance for the first time, please read carefully these Instructions for Use.
• The appliance should be connected to sockets compliant with current parameters given on the casing.
• The appliance should always be disconnected by pulling the plug, not the power cord.
• The device can be used by children aged 8 and older and by persons with limited physical, sensory or mental capabilities, or persons without sufficient experience and knowledge only under supervision or if previously instructed on the safe use of the appliance and the possible risks. Children shall not play with the appliance. Cleaning and maintenance that are the responsibility of the user shall not be carried out by children without supervision. Protect the appliance and the power cord against children under 8 years old.
• Do not place the appliance in the vicinity of heat sources.
• The appliance is intended for domestic use only.
• Do not immerse the cord or the appliance in water.
• The appliance must always be cleaned after use. The appliance must always be turned off before cleaning and maintenance as well as in case of malfunction and after operation.
• Do not use with a broken or otherwise damaged hairdressing head as it may lead to injury.
• Do not use the appliance for clipping animal and artificial hair.
• Do not use the appliance for clipping wet hair. It is designed for clipping dry hair only.
• Do not use in the open air.
• Use only with the originally included accessories and feeder.
• Never use the appliance when it is wet, with wet hands or in the vicinity of showers, water in a bath, washbasin and other containers.
• When used in the bathroom, the appliance must be disconnected after use because proximity of water is dangerous even if the appliance is turned off.

SAFETY INSTRUCTIONS

• The appliance must not be immersed in or sprinkled with water.
• When in operation, do not leave the appliance unattended.
• The power cord and the whole appliance should be regularly checked for damage. Do not turn the appliance on, if any damage has been found.
• In the event the power cord is damaged, it must be replaced in the Manufacturer's Service Centre to prevent danger. A list of Service Centres can be found in the attachment and on the website www.eldom.eu.
• The appliance can be repaired only in an authorised Service Centre. Any modernisation or application of spare parts or elements other than the original ones is forbidden and dangerous for the user.
• The company Eldom Sp. z o.o. shall not be liable for any damage caused by inappropriate use of the appliance.

ENVIRONMENTAL PROTECTION

• The appliance is made of materials which can be reprocessed or recycled.
• The appliance should be disposed of only in authorised disposal centres which deal with collecting and recycling electrical and electronic appliances.

GUARANTEE

• The appliance is intended for private domestic use only.
• The appliance may not be used for professional purposes.
• The guarantee ceases to be valid in case of inappropriate handling.
  Detailed guarantee conditions can be found in the attachment.

INSTRUCTIONS FOR USE

HAIR CLIPPER MG10N

fot. 1

DESCRIPTION OF THE SET

1. Cutting head
2. Hair length control ring
3. Switch-key
4. Control lamp
5. Comb heads (3 mm, 6 mm, 9 mm, 12 mm)
6. Feeder
7. Maintenance oil
8. Cleaning brush
9. Battery
   10.Charging port

HOW TO USE THE APPLIANCE

Before the first use, put the battery in, phot. 1.

The Hair Clipper MG10N can be used as an appliance powered

by electricity or a battery. If the appliance is powered

by electricity, it is ready to be used right away.

ELECTRIC POWER SUPPLY

• Turn off the appliance, the switch-key (3) in position "0".
• Plug in the feeder (6) and connect it to the hair clipper.
• Power supply is signalled by the red control lamp (4)
• To start operation, turn the switch-key (3) to position "1".
• when finished, turn off the device by pushing the switch (3) down and disconnect the power cable from the socket and then from the device port (10)

CHARGING AND OPERATION WITH THE BATTERY

- Turn off the appliance, the switch-key (3) in position "0".

- Plug in the feeder (6) and connect it to the hair clipper.

- Charging is signalled by the red control lamp (4).

Battery charging time: approx. 8 hours

NOTICE: The control lamp (3) does not go out after the battery has been charged.

- After the battery has been charged, disconnect the feeder, the appliance is ready for operation with the battery. To start operation, turn the switch-key (3) to position "1".

Charging the battery for over 12 hours reduces its life span.

If the appliance is not used for a longer period of time, it is recommended to charge the battery at least once every half a year. Failure to charge the battery for a period of over 6 months also

TECHNICAL DATA

• supply voltage: 230 V \~ 50 Hz
• power: 3 W
• battery: 900mA, Ni-Cd
• charging time: 8 hours

HAIR CLIPPING

• Make sure the appliance is clean, correctly assembled and oiled.
• Before clipping the hair, comb it to make it more natural.
• Install the right comb head (5) by sliding it in the side slideways of the cutting head (phot. 2). To remove the comb head, press the "PUSH" area on the comb head and move it according to the indicated direction.

The rotating ring (2) allows for precise control of hair length: 0.8 mm - 2 mm. Additional comb heads (5) of 3 mm, 6 mm, 9 mm and 12 mm, and the 5-grade control ring offer 25 different hair lenghts.

• It is recommended to start clipping with the use of the comb head for longer hair.
• Clip small areas by moving the appliance slowly through the hair.
• Start clipping from the neck upwards or from the forehead and the temple upwards.
• Hold the appliance gently under the hair, so that the comb heads are pointed upwards and lie flat on the head.
• Without using the comb heads, the hair can be clipped evenly to the length of 0.8-2 mm.

Do not use the appliance for clipping wet hair.

Close-up of a hair styling tool with a black and silver brush, showing teeth and a 2.5mm mark (no text or symbols on the tool itself)

phot. 2

Close-up of a hairpin with an orange arrow indicating the cutting edge (no text or symbols visible)

phot. 3

CLEANING AND MAINTENANCE

After using the appliance, the chamber of cutting knives should always be cleaned. For this purpose, open the cutting head (1) by pressing the clipper blades with your thumb in the direction shown in phot. 3. Protect the blades against falling down.

NOTICE

Before opening the cutting head, turn the hair length control ring (2) to position "2 mm".

Clean the blades with the brush included in the set.

Cutting blades must be maintained on a regular basis. Put one to two drops of oil between the blades and turn the appliance on for a few seconds.

Do not use hair oils, fat, oils mixed with refined kerosene or other solvents.

Do not immerse the appliance in water. Before cleaning, unplug the appliance and turn it off. Do not use any cleansing agents which are strong or may damage the surface.

Wipe the casing with a moist or dry cloth.

The cutting blades are wear parts and should be maintained on a regular basis.

The are not covered by the guarantee.

BEZPEČNOSTNÍ DOPORUČENÍ

Close-up of a hair styling tool with black and white brush (no text or symbols visible)

obr. 2

Close-up of a hairpin with an orange arrow indicating a cutting tool (no text or symbols visible)

obr. 3

ČIŠTĚNÍ A ÚDRŽBA

Close-up of a hair styling tool with black and white teeth, showing a 2.5mm mark (no text or symbols on the tool itself)

Foto Nr. 2

Close-up of a hairpin with an orange arrow indicating the cutting edge (no text or symbols visible)

Foto Nr. 3

фото 1

ОБЩАЯ ИНФОРМАЦИЯ

Close-up of a hair styling tool with black and white brush (no text or symbols visible)

фрото 2

Close-up of a hairpin with an orange arrow indicating the cutting edge (no text or symbols visible)

фото 3

ЧИСТКА И УХОД

výkr. 1

OPIS SUPRAVY

1. Głowica tnąca
2. Regulátor nastavenia dlžky strihania
3. Vypínač
4. Kontrolné svetlo
5. Hrebeňové nadstavce (3mm, 6mm, 9mm, 12mm)
6. Zdroj napajania
7. Olej na konzerváciu
8. Kefka na čistenie
9. Akumulátor
   10.Zásuvka pripojenia napájacieho káblu

TECHNICKÉ ÚDAJE

Close-up of a hair styling tool with black and white brush (no text or symbols visible)

obrázok. 2

Close-up of a hairpin with an orange arrow indicating the cutting edge (no text or symbols visible)

obrázok. 3

ČISTENIE A KONZERVÁCIA

abra. 1

A KÉSZLET LEÍRÁSA

Close-up of a hair styling tool with black and silver teeth, showing toothed edge and handle (no text or symbols visible)

ábra 2

Close-up of a hairpin with an orange arrow indicating rotation (no text or symbols visible)

ábra 3

fig. 1

DESCRIPCIÓN DEL KIT

Close-up of a hair styling tool with black and white teeth, showing a 2.5mm mark (no text or symbols on the tool itself)

fig. 2

Close-up of a hairpin with an orange arrow indicating the brush tip (no text or symbols visible)

fig. 3

LIMPIEZA Y MANTENIMIENTO