Clipp MG100S - Scissors Eldom - Free user manual and instructions

Type	Hair Clipper
Brand	Eldom
Model	Clipp MG100S
Power Supply	230V~50Hz, 3W
Battery	3.7V Li-Ion, 2000mAh
Charging Time	~4 hours (max 10 hours)
Cutting Length Range	0.8 – 2 mm (without comb); up to 14 mm with combs
Number of Cutting Lengths	25
Included Comb Caps	3 mm, 6 mm, 9 mm, 12 mm
Operation Modes	Mains or battery powered
Indicator Light	Red (charging), Green (fully charged)
Blade Type	Precision adjustable steel blades
Maintenance	Oil blades regularly; clean after each use
Safety Features	Do not use near water; only for dry hair; do not use on animals or artificial hair
Includes	Power supply, maintenance oil, cleaning brush, 4 comb caps
Country of Origin	Poland
Warranty	For personal household use only

Frequently Asked Questions - Clipp MG100S Eldom

How do I charge the Clipp MG100S?

Insert the battery first, then connect the power cord to the socket (7) on the clipper and plug the power supply into a mains outlet. The indicator light turns red during charging and green when fully charged. Charging takes about 4 hours and should not exceed 10 hours.

Can I use the clipper while it is charging?

Yes, you can use the clipper connected to the mains by plugging it in. The device can be operated either from the mains or on battery after charging.

How do I adjust the cutting length?

Use the cutting-length-adjustment ring (2) to set a length between 0.8 mm and 2 mm. For longer lengths, attach one of the four comb caps (3, 6, 9, 12 mm) by sliding it onto the head. The combination of ring and caps provides 25 different lengths up to 14 mm.

How should I clean the clipper after use?

Turn off the device and disconnect it from the power supply. Remove the comb cap and cutting head. Brush away hair from the blades and housing. The comb caps can be rinsed under running water. Wipe the housing with a damp or dry cloth. Do not immerse the device or power supply in water.

How often should I oil the blades?

Oil the blades regularly, especially before each use or after cleaning. Apply one to two drops of the included maintenance oil to the places indicated in the manual, then run the clipper for a few seconds. Only use the supplied oil; do not use hair oils or other solvents.

Can I use the clipper on wet hair?

No, the clipper is designed for cutting dry hair only. Do not use on wet hair as it may damage the device or cause injury.

What should I do if the blades are damaged?

If you find damage to the blades, replace them immediately. The blades are sharp, so handle with care. Only use original replacement parts from an authorized service center.

Is the clipper safe to use in the bathroom?

The clipper should not be used near bathtubs, showers, swimming pools, or other water reservoirs. It is not safe to use in the bathroom unless disconnected from the mains and stored away from water.

How long does the battery last after a full charge?

The manual does not specify the exact runtime, but the battery is 2000mAh and the device consumes 3W. Typically, it should provide enough power for multiple haircuts. For longest battery life, charge in one uninterrupted cycle after a complete discharge.

Can I use the clipper on pets or artificial hair?

No, the clipper is intended for human hair only. Do not use on animal hair or artificial hair, as it may damage the blades and is not designed for that purpose.

USER MANUAL Clipp MG100S Eldom

Two power III BLADE telegraph chime designs shown side by side (no text or symbols visible on the designs themselves)

Eldom Sp. z o.o. • ul. Pawła Chromika 5a • 40-238 Katowice, POLAND tel: [phone] • fax: [phone] • www.eldom.eu

Before using the appliance for the first time, please read carefully these Instructions for Use.

1. The appliance should be connected to sockets compliant with current parameters given on the casing.
2. The appliance should always be disconnected by pulling the plug, not the power cord.
3. The device can be used by children aged 8 and older and by persons with limited physical, sensory or mental capabilities, or persons without sufficient experience and knowledge only under supervision or if previously instructed on the safe use of the appliance and the possible risks. Children shall not play with the appliance. Cleaning and maintenance that are the responsibility of the user shall not be carried out by children without supervision. Protect the appliance and the power cord against children under 8 years old.
4. Do not place the appliance in the vicinity of heat sources.
5. The appliance is intended for domestic use only.
6. Do not immerse the cord or the appliance in water.
7. The appliance must always be cleaned after use. The appliance must always be turned off before cleaning and maintenance as well as in case of malfunction and after operation.
8. Do not use with a broken or otherwise damaged hairdressing head as it may lead to injury.
9. Do not use the appliance for clipping animal and artificial hair.

10. Do not use the appliance for clipping wet hair. It is designed for clipping dry hair only.

11. Do not use in the open air.

12. Use only with the originally included accessories and feeder.
13. Never use the appliance when it is wet, with wet hands or in the vicinity of showers, water in a bath, washbasin and other containers.
14. When used in the bathroom, the appliance must be disconnected after use because proximity of water is dangerous even if the appliance is turned off.
15. The appliance must not be immersed in or sprinkled with water.
16. When in operation, do not leave the appliance unattended.
17. The power cord and the whole appliance should be regularly checked for damage. Do not turn the appliance on, if any damage has been found.
18. In the event the power cord is damaged, it must be replaced in the Manufacturer's Service Centre to prevent danger. A list of Service Centres can be found in the attachment and on the website www.eldom.eu.
19. The appliance can be repaired only in an authorised Service Centre. Any modernisation or application of
20. spare parts or elements other than the original ones is forbidden and dangerous for the user.
21. The company Eldom Sp. z o.o. shall not be liable for any damage caused by inappropriate use of the appliance.

CAUTION:

Do not use the appliance near bathtubs, showers, swimming pools and similar water reservoirs.

GENERAL DESCRIPTION

1. Trimming head
2. Cutting-length-adjustment ring
3. Power on/off switch
4. Battery cover
5. Battery
6. Indicator light
7. Socket for power-cord connection
8. Comb caps (3mm, 6mm, 9mm, 12mm)
9. Power supply
10. Maintenance oil
11. Cleaning brush

TECHNICAL DATA

• 230V \~ 50Hz
• power: 3 W
• battery: 3.7V, Li-ION, 2000mAh
• charging time: \~ 4 hours

INTENDED USE

The MG100 clipper is designed for cutting hair. Thanks to the precise blade adjustment, and the 4 caps, the clipper gives 25 different cutting lengths - from 0.8 to 14 mm. The MG100 can be used as a mains-powered or battery-powered device.

USE

Before the first use, put in the battery (5) Fig. 2 and oil the head (1) – see CLEANING and MAINTENANCE.

• Using the device is possible after charging the battery, or from the mains – connect the power cord correctly to the socket (7), and plug the power supply into the mains, according to the parameters given in the manual.
• The device is equipped with an internal battery with a charging time of about 4 hours. To extend the life of the battery, charging should be carried out in one uninterrupted cycle after a complete discharge.
• During charging, the indicator bulb (6) lights up red. Green indicates that the device is fully charged.
• After charging, unplug the device from the mains and disconnect the power cord from the socket (7).

NOTE

The charging time must not exceed 10 hours, as this will affect the service life of the battery, and in extreme cases it can cause damage to the battery.

During charging and while operating when plugged in, the device might heat up a little - this is normal and does not affect the safety of use.

USE

• Make sure that the clipper is clean, correctly assembled, and oiled.
• Before cutting, comb your hair to let it fall naturally.
• Use the ring (2) to set the desired cutting length between 0.8 mm and 2 mm.
• If necessary, insert a suitable cap (8) by sliding it into the side guides of the head. To remove the cap, press the "PUSH" field on the cap, sliding in the direction indicated.

NOTE. It is advisable to start cutting by using the longer-hair cap.

• The device starts working after you push the switch (3).
• Start the cutting with small areas.
• Clipping should start from the neck upwards, or from the forehead and temples upwards
• Hold the hair clipper gently under the hair so that the teeth of the cap face upwards and lie flat on the head.
• Slowly glide over your hair.
• To switch the device off, press the power on/off switch (3) again.

CLEANING

• Turn off the device using the switch (3) before cleaning the machine, replacing the blade, or all maintenance work.
• The device must be disconnected from the power supply.
• Clean the device after each use.
• Neither the device nor the power supply should be immersed in water.
• Do not use strong or cleaning agents or cleaning products which can damage the surface.
• Remove the cap (8) by pressing the "PUSH" field and sliding in the direction indicated.
• Set the ring (2) in the 2mm position, then remove the cutting head (1) by pressing the shaver blades with the thumb in the direction shown in Fig. 3.
• Remove any accumulated hair.
• The caps (8) may be rinsed under running water.
• Wipe the housing with a damp or dry cloth.

Close-up of a mechanical component with a curved arrow indicating rotation (no text or symbols visible)

Illustration of hands assembling a mechanical component with magnified detail (no text or symbols)

Note

The edges of the blades (1) are sharp, so be careful when handling them.

Prevent the blades (1) from falling out.

If damage is found, the blade (1) must be replaced immediately.

MAINTENANCE

- The cutting blades must be maintained regularly.

- Put one to two drops of oil into the places indicated in Fig. 4, then fit the blade and switch on the device for a few seconds.

NOTE

Only the accompanying oil may be used for oiling the head.

Do not use hair oils, fats, oils mixed with purified kerosene, or other solvents.

ENVIRONMENTAL PROTECTION

- the appliance is made of materials which can be recovered or recycled

- the appliance should be handed over to the appropriate centre of collection and recycling of electrical and electronic equipment

WARRANTY

• the appliance is intended for personal use at a household,
• it is not intended for professional purposes,

10 EN

DOPORUČENÍ PRO OBLAST BEZPEČNOSTI

Close-up of a mechanical component with a curved arrow indicating rotation (no text or symbols visible)

Technical illustration of mechanical assembly with hands and close-up insets (no text or symbols)

POZOR:

Close-up of a mechanical component with a curved arrow indicating rotation (no text or symbols visible)

Technical illustration of mechanical assembly with hands and close-up insets (no text or symbols)

Achtung:

Close-up of a mechanical component with a curved arrow indicating rotation (no text or symbols visible)

Technical illustration of mechanical assembly with hands and close-up insets (no text or symbols)

Pozor:

Blank gray image with no visible content, text, or symbols