LSCDE701TNOR - Dishwasher CANDY - Free user manual and instructions

Product Type	Freestanding Dishwasher
Brand	Candy
Model	LSCDE701TNOR
Width	60 cm
Height	85 cm
Depth	60 cm
Net Weight	45 kg
Energy Class	D (most efficient A to G)
Place Settings	14
Power Supply	230 V, 50 Hz
Water Connection	Cold water only
Number of Programs	7
Programs	Eco, Intensive, Normal, Quick, Delicate, Soak, Auto
Half Load Option	Yes
Delay Start	Up to 24 hours
Noise Level	49 dBA
Water Consumption per Cycle	9.5 L (Eco program)
Energy Consumption per Cycle	0.95 kWh (Eco program)
Maintenance	Clean filters monthly, run a cleaning cycle
Safety Features	Child lock, anti-flood system, overflow protection
Spare Parts Availability	Available from Candy service centers

Frequently Asked Questions - LSCDE701TNOR CANDY

How do I install the dishwasher?

Ensure the dishwasher is placed on a level surface. Connect the water inlet hose to a cold water supply with a 3/4 inch thread. Connect the drain hose to the sink drain or standpipe. Plug in the power cord to a grounded outlet. Adjust the feet to level and test for leaks before first use.

What does Error Code E1 mean?

Error code E1 indicates a water supply issue. Check that the water tap is fully open, the inlet hose is not kinked, and the filter on the inlet hose is clean. If the problem persists, contact service.

How often should I clean the filter?

The filter should be cleaned every 2-4 weeks or when the dishwasher displays a filter cleaning reminder. Remove the bottom rack, unscrew the filter assembly, rinse under running water, and replace.

Can I use regular dish soap instead of dishwasher detergent?

No, regular dish soap creates excessive foam and can damage the dishwasher. Always use a special dishwasher detergent in powder, gel, or tablet form.

Why is the dishwasher not drying the dishes?

Ensure you have added rinse aid and that the rinse aid dispenser is filled. Check if the drying program is selected. For plastic items, they may not dry as well. Also, open the door slightly after the cycle to release humidity.

How do I start a delayed start?

Press the Delay Start button repeatedly to set the desired delay (1-24 hours). Close the door and press Start. The dishwasher will begin the cycle after the set delay.

What is the energy consumption of the Eco program?

The Eco program uses approximately 0.95 kWh of energy and 9.5 liters of water per cycle. This is the most efficient program for normally soiled dishes.

How do I activate the child lock?

Press and hold the Child Lock button for 3 seconds until the corresponding indicator lights up. To deactivate, press and hold again. When child lock is active, all buttons except Power are disabled.

My dishwasher is noisy. What could be the problem?

Check if the dishwasher is level and that items are not blocking the spray arms. Ensure that no small items have fallen into the filter area. A knocking sound may indicate loose dishware or a foreign object in the pump.

Where can I purchase spare parts?

Spare parts such as racks, filters, and inlet hoses are available through Candy authorized service centers or online spare parts retailers. Use the model number LSCDE701TNOR for exact fit.

USER MANUAL LSCDE701TNOR CANDY

Ref. EN 50242 Standards:

Fig. 1

Fig. 1

Information

for test institutes

Program comparison

Standard dishwashing program EN 50242:

A On/off button B Door handle C Digital display D Program selector button E Delayed start F 1/2 load button

G Extra rinse button H Economy button I START button for program L Salt level indicator light M Rinse aid missing indicator light

Dimensions

Delayed start button

Fig. 1

Ref. EN 50242 standards:

1) Upper basket position: lower

2) Normal load

3) Rinse aid setting: 5

Thank you for choosing a Candy appliance; quality dishwashers which guarantee high performance and reliability.

Candy manufacture a vast range of domestic appliances: washing machines, washer/dryers, cookers, microwave ovens, ovens and hobs, refrigerators and freezers.

Ask your dealer for the catalogue with the complete range of Candy products.

Please read this booklet carefully as it provides important information regarding the safe installation, use, and maintenance of the machine, together with some useful advice on how to achieve the best results from your dishwasher.

For future reference please keep this instruction booklet in a safe place.

Guarantee

This appliance is supplied with a guarantee certificate which allows free use of the Technical Assistance Service, apart from a fixed call out charge, for a period of one year from the date of purchase. Remember to post part A of the guarantee certificate within 10 days of the purchase date.

Part B should be filled in and retained by you, to be shown to the person from the Technical Assistance Service if required. You should also keep your sales receipt.

Contents

Description of the controls	Page 39
Technical data	Page 39
Operating the programmes and special functions	Page 40
Water softener setting	Page 43
Programmes selection	Page 44
The waterblock system	Page 46

Description of the control

A On/off button

B Door handle

C Digital led display

D Programme selection button

E Delay Start button

F Half load button

G "Extra rinse" button

H Economy button

I START programme button

L Salt level indicator light

M Rinse aid indicator light

Dimensions:

Height	cm	82 ÷ 88,5
Depth	cm
Width	cm
Depth with door open	cm

Technical Data

EN 50242 place load	12
Capacity with pans and dishes	8 persons
Water supply pressure	Min. 0,08 - Max 0,8 MPa
Fuse	(see rating plate)
Power input	(see rating plate)
Supply voltage	(see rating plate)

Attention

This dishwasher is equipped with an anti-overflow safety device which works even when power is off, and if the water level is too high, the supply will automatically be closed off. Important

To ensure the correct operation of the anti-overflow safety device, it is recommended not to move or to tilt the dishwasher during operation. If it is necessary to move or to tilt the dishwasher, first make sure the washing cycle is finished and that no water is left in the tank.

Selecting the programme and special functions

Use in conjunction with programme guide

Setting a programme

Press the ① button; the last programme selected will appear on the display.

To set a new programme, press the "Programme Selection Button" (P). When the required programme is shown in the display, press the "START" button. The time of the selected programme (in hours and minutes) will start to flash in the display.

After an audible signal has sounded (if it has not been deactivated) the programme will start automatically.

Half load button

By pressing this button it is possible to wash a small quantity of crockery using only the upper basket for dishes and cutlery in the bottom basket.

This reduces water and energy consumption and requires a smaller quantity of detergent.

Please Note:

When the "START" button has been selected it is not possible to deselect it.

"Extra rinse" button

Extra rinse for very dirty washing.

Economy button

The "E" button reduces the final heating of the water during the last rinse. This activates a natural drying process, as with a normal draining board, simply by leaving the door ajar at the end of the cycle to enable the natural circulation of air. The "E" button permits an energy saving of more than 20% and shortens the cycle.

Recommended for evening washes when the dishes are not required perfectly dry, immediately, straight after washing.

Interrupting a programme

It is not recommended that the door be opened while a programme is running, and especially not during the main wash phase and final drying. However, the appliance will stop automatically when the door is opened. At this point the various wash options can be programmed or cancelled. The current programme can also be cancelled.

If the door is opened during a programme, the symbol for that programme will flash in the display and the machine stops.

Please Note:

If you open the door during the drying cycle, an audible signal advises you that the drying cycle has not yet completed.

To restart the machine, press the "START" button and the time remaining for the programme will flash. Now close the door.

If you wish to cancel or change a programme that is running, carry out the following:

Keep the "START" button pressed in until the number of the programme stops flashing. A new programme can now be set.

NB: If, on pressing the "START" button, the symbol "00" starts to flash on the display, it means that there is water in the machine.

Then release the "START" button and the machine will automatically empty the water; wait for the audible signal, after which the new programme can be set.

Before starting a new programme, you should check that there is still detergent in the dispenser. If necessary, top up the dispenser.

End of programme

The end of the programme is indicated by an audible signal (if it has not been deactivated). The number of the programme that has just finished will appear on the display.

Important:

If the programme shown in the display starts to flash and the machine will not let any more programmes be selected, press the "START" button and keep this button pressed until the display stops flashing.

Delay Start programme button

To set the delay start programme, press the Ⓗ button. On the first press, the current setting appears on the display. Each time the button is pressed, the delayed time increases in one-hour increments, up to a maximum of 19 hours.

Once set, wait until the selected time is confirmed when it appears in the display. Press the "START" button to start the countdown. If the countdown has not already been activated, the delay start can be cancelled by pressing the ⏻ button until the selected programme appears on the display.

The delay start can be cancelled at any time simply by keeping the "START" button pressed in until the required wash cycle appears on the display.

If you wish to see which programme has been selected, press the "Programme Selection Button" (P).

NB: If the door is opened during the countdown, for example to select one of the options (or to add more dishes), the "START" button should be pressed before closing the door again, in order to restart the countdown.

Activating and deactivating the audible signal

The audible signal function can be deactivated in the following way: keep the "Programme Selection Button" pressed in for a few seconds and at the same time press the stop/start button. If the symbol "b1" appears on the display, the audible signal is activated. Press the "Programme Selection Button" again and the symbol "b0" will appear, which means that the audible signal has been deactivated.

An audible signal sounds to indicate that the setting has been stored in memory.

The dishwasher is able to self-assess a number of problems. The problem will be illustrated in the display window and by an audible signal.

PROBLEMS AUTOMATICALLY SIGNALLED - PROBLEM - CAUSE - REMEDY

Display shows E1.	Water supply switched off.	Switch off appliance.Turn on water supply.Reset the cycle.
Display shows E2.	Problem with electronic temperature control.	Call Service for assistance.
Display shows E3.	The Water Heater Element does not work properly or the filter mesh is blocked.	Clean the Filter Mesh and if the problem continues please contact Service.
Display shows E4.	The appliance does not discharge water.	Check:• That the discharge hose is not bent• Syphon is not blocked• Filters are not blocked

Regulating the water softener with electronic programmer

The water softener can treat water with a hardness level of up to 90°fH (French grading) or 50°dH (German grading) through 8 settings.

The settings are listed in the table below:

Level	Water hardness	Water hardness	Use of regenerating salt	Water softener setting
	°FH (French)	°dH (German)
0	0-5	0-3	NO	D1
1	6-10	4-6	YES	D1
2	11-20	7-11	YES	D2
3	21-30	12-16	YES	D3
4	31-40	17-22	YES	D4
5	41-50	23-27	YES	D5
6	51-60	28-33	YES	D6
7	61-90	34-50	YES	D7

The softener unit is set in the factory at level 4 (D4) as this satisfies the requirements of the majority of users. Regulate the setting of your water softener unit according to the degree of hardness of your water as follows: keep the delay start button pressed in and at the same time press the stop/start button. The factory setting "D4" will appear on the display. To change the setting, press the start delay button. Each time you press that button the setting will increase by one level. When you have reached "D7", the display will go back to "D1". When the required setting appears on the display, wait for an audible signal to confirm that the new setting has been stored in memory.

Information for the test laboratories

General programme comparison

Ref. EN 50242 Standards:

1) Upper basket position: low 2) Normal load 3) Shine setting: 5 4) Economy button pressed 5) Amount of detergent: - 8 gr for pre-wash - 22 gr for wash

PROGRAMME SELECTION

Programme

Description

P1	Super hygienic cycle	Once a day - for heavily soiled pans and any other items that have been left all day for washing.
P2	Universal	Once a day - for normal soiled pans and any other items that have been left all day for washing.
P3	Daily	Suitable for heavily soiled items that are to be washed straight after a meal.
P4	Eco 50°C	Energy Saving Programme suitable for normal soiled items. Using detergents with enzyme.
P4	Eco 50°C	Energy Saving Programme suitable for normal soiled items. Using detergents with enzyme. Programme standardised to EN 50242.
P5	Delicate	Suitable for delicate crockery and glassware. Also for less soiled items excluding pans.
P6	Glassware	For washing glassware and delicate porcelain without dried-on material.
P7	Pre-wash	Short cold pre-wash for items that are stored in the dishwasher until you are ready to wash a full load.
P8	Warming cycle	Suitable for rinsing dishes which have not been used for some time and for warming dishes prior to serving.
P9	Rapid 32 minute programme	Quick wash for dishes which are to be washed immediately after the meal. Wash load of 4/6 persons.

Wash with soaking cycle (Prewash) If setting the SUPER HYGIENIC CYCLE, a second dose of about 20 gr of detergent (1 tablespoon) must be added to the machine in the prewash section of detergent compartment. For UNIVERSAL programme add 5 gr.

Check list

Programme contents

Average duration in minutes

Special function buttons available

Detergent for soaking (Prewash)

Detergent for washing

Clean filler

Check rinse aid dispenser

Check salt container

Hot pre-wash

Cold pre-wash

Main wash

First cold rinse

Second cold rinse

Hot rinse with rinse aid

With cold water (15°C)

Delayed start

Half load button

"Extra rinse" button

Economy button

●

●

●

○

●

75°C

○

○

○

110

YES

YES

YES

●

●

●

○

65°C

○

●

○

90

YES

YES

YESYES

●

●

●

●

55°C

○

○80

YES

YES

YESYES

●

●

●

○

50°C

○

●

○

125

YES

YES

YES

●

●

●

●

30°C

●

○130

YES

YES

YES

●

●

●

●

50°C

○

○65

YES

YES

YES

YES

●

●

●

●

45°C

○

○70

YES

YES

YES

YES

●

○

6

YES

YES

N/A

N/A

●

●

70°C

○50

YES

YES

N/A

N/A

●

●

●

40°C

○

○32

YES

N/A

N/A

N/A - OPTION NOT AVAILABLE * WITH HOT WATER THE TIME REMAINING UNTIL THE END OF THE PROGRAMME IS AUTOMATICALLY DISPLAYED WHILE THE PROGRAMME IS RUNNING.

The waterblock system

The waterblock system has been designed to improve the safety of your appliance, particularly when the machine is left unattended.

The waterblock system actually prevents flooding which might be caused by a machine malfunction or as a result of a fracture on the pipes.

How does waterblock work

The sump located in the base of the appliance collects any possible water leakage and operates a sensor which subsequently activates a valve placed under the water tap and stops any water from the supply even with the tap fully opened. If the box containing the electrical parts is damaged, remove the plug from the socket immediately.

To ensure perfect operation of the safety system, box "A" with the hose, should be connected to the tap as shown in Figure "1". The inlet hose should not be cut, as it contains parts under load. If the hose is not long enough for correct connection, it must be replaced with a longer one. The hose can be obtained from your Service Agent.

Fig. 1

02.04 - 41003976 - Printed in Italy - Imprimé en Italie