KI5672FF0 - Refrigerator NEFF - Free user manual and instructions

Product type	Combined refrigerator with freezer compartment
Dimensions (H x W x D)	177 cm x 60 cm x 65 cm (estimated)
Net weight	Approximately 70 kg
Power supply	220-240 V, 50 Hz
Energy class	A+ (estimated)
Total net volume	Approximately 300 L (refrigerator 210 L, freezer 90 L)
Climate class	SN-ST (ambient temperature 10 °C to 38 °C)
Noise level	42 dB(A) re 1 pW (estimated)
Interior lighting	LED, replaceable by a professional
Fruit and vegetable drawer	Yes, with lid and removable divider
Cool-Fresh drawer	Yes, for optimal preservation
Telescopic shelf	Yes, in the refrigerator
Reversible door	Yes, via flat or slide hinges
Replaceable door gasket	Yes, by the consumer
Spare parts available	Gaskets, hinges, shelves, drawers, LED modules
Repairability	Designed for user replacement of parts (gaskets, shelves, drawers)
Safety	Unplug 60 seconds before any intervention
Manual available	Free PDF in multiple languages at notice-facile.com

Frequently Asked Questions - KI5672FF0 NEFF

How to replace the door gasket of the NEFF KI5672FF0 refrigerator?

Remove the old gasket by pulling it out of the grooves. Before installing the new gasket, gently warm it to restore its shape. Insert the corners first, then gradually press the gasket into the groove. Make sure the groove is not damaged.

Can I repair the LED lighting myself?

No, LED lighting repair is reserved for the after-sales service or a certified specialist. There is a risk of electrocution. Always unplug the appliance before any intervention.

How to remove and reinstall the glass shelves?

To remove a shelf, lift it slightly and pull it towards you. Reinstall in reverse order. Ensure the shelf clicks into place.

How to replace the fruit and vegetable drawer?

Fully pull out the drawer towards you, then lift it to remove. Install the new drawer in reverse order.

Is it possible to change the door opening direction?

Yes, the NEFF KI5672FF0 refrigerator allows door reversal using flat or slide hinges. Follow the assembly instructions provided. Disconnect the appliance before starting.

What to do if the door gasket is deformed?

Slight deformation is normal. Warm the gasket with a hairdryer or hot water, then reshape it by hand before installation. If the gasket is damaged, replace it.

What tools are needed to replace a hinge?

You will need a Torx TX20 bit (6.3 mm, 1/4 inch). Wear protective gloves and disconnect the appliance from the mains at least 60 seconds before.

How to clean the Cool-Fresh drawer?

Remove the drawer by tilting it forward. Wash with warm water and mild detergent. Dry thoroughly before reinstalling.

Where can I download the complete manual?

The manual is available for free in PDF format on notice-facile.com. You can also request a translation in your language by providing your email address.

How to replace the freezer compartment shelf?

Pull the shelf towards you to remove it. To reinstall, insert it and push until it clicks. Do not force it.

USER MANUAL KI5672FF0 NEFF

Repair

Repair

Repair

1. Remove the four screws (1).
2. Remove the lower hinges (2)

The hinges are removed.

The shelf is removed.

Repair

Repair

The door seal is installed.

Repair

Torx TX20 6.3 mm (1/4") extension [00340865]

Heavy, large appliances!

Repair

1. Loosen the four screws (1).
2. Push the upper door outward and remove it (2).

1. Remove the four screws (1).
2. Remove the hinges (2).

The upper door hinges have been removed.

1. Loosen the four screws (1).
2. Push the lower door outward and remove it (2).

1. Remove the four screws (1).
2. Remove the hinges (2).

The lower door hinges have been removed.

Repair

4.2.2 Installing the flat hinge

▶ Install in reverse order.

Repair

Torx TX20 extension 6.3 mm (1/4") [00340865]

Heavy, large appliances!

Repair

1. Remove the four screws (1).
2. Remove the lower hinges (2).

The hinges have been removed.

1. Pull out the pull-out shelf and turn it sideways.
2. The pull-out shelf has been removed.

4.6.2 Installing the pull-out shelf

▶ Install in reverse order.

Repair

4.7 Replacing the freezer compartment shelf

Requirement:

The door is open.

4.7.1 Removing the freezer compartment shelf

The freezer compartment shelf has been removed.

4.7.2 Installing the freezer compartment shelf

▶ Install in reverse order.

Repair

4.8 Replacing the frozen food container

Requirement:

The door is open.

4.8.1 Removing the frozen food container

1. Fully pull out the frozen food container (1).
2. Remove the frozen food container (2).

The frozen food container has been removed.

4.8.2 Installing the frozen food container

→ The container has been removed.

1. Remove the fruit and vegetable container.→44
2. Press the lever under both sides of the partition (1).
3. Pull the partition forward (2).

1. Lift the shelf and turn it sideways outward.

→ The shelf has been removed.

The freshness maintenance container has been removed.

Repair

Repair

Repair

Repair

Repair

Repair

1. Press the gasket evenly into the groove.

Repair

Repair

The shelf has been removed.

Repair

1. Disconnect the electrical connection of the LED spot lamp.

Repair

Repair

Repair

Repair

Repair hints - Fridge-freezer

i Concerning this document.... 123

1.1 Important information.... 123

1.1.1 Purpose.... 123

1.2 Explanation of symbols 123

1.2.1 Danger levels.... 123

1.2.2 Hazard symbols 123

1.2.3 Structure of the warnings.... 124

1.2.4 General symbols.... 124

Safety....

2.1 General Safety instructions 125

2.1.1 All domestic appliances 125

Tools and aids....12

Repair

4.7 Replacing freezer compartment shelf.... 138

4.7.1 Removing freezer compartment shelf 138

4.7.2 Installing freezer compartment shelf.... 138

4.8 Replacing frozen food container....139

4.8.1 Removing frozen food container 139

4.8.2 Installing frozen food container 139

4.9 Replacing fruit and vegetable container 140

4.9.1 Removing fruit and vegetable container 140

4.9.2 Installing fruit and vegetable container 140

4.10 Replacing partition and cover of fruit and vegetable container.... 141

4.10.1 Removing partition and cover of fruit and vegetable container ..... 141

4.10.2 Installing partition and cover of fruit and vegetable container.... 141

4.11 Replacing cool-fresh container.... 142

4.11.1 Removing cool-fresh container 142

4.11.2 Installing cool-fresh container.... 142

4.12 Replacing extendable container 143

4.12.1 Removing extendable container 143

4.12.2 Installing extendable container 143

4.13 Replacing LED spot light 144

4.13.1 Removing LED spot light.... 144

4.13.2 Installing LED spot light 145

Concerning this document

1.1 Important information

1.1.1 Purpose

These repair hints support consumers to repair appliances by themselves according to the applicable eco-design regulation (as of 03/2021).

They contain information on how to exchange defined spare parts, including warnings and risks.

In case of questions, please contact our customer service. We will only be liable for damages if the repair hints have been followed properly.

1.2 Explanation of symbols

1.2.1 Danger levels

The warning levels consist of a symbol and a signal word. The signal word indicates the severity of the danger.

Warning level Meaning
Danger	Non-observance of the warning message will result in death or serious injuries.
Warning	Non-observance of the warning message could result in death or serious injuries.
Caution	Non-observance of the warning message could result in minor injuries.
Notice	Non-observance of the warning message could result in damage to property.

Table 1: Danger levels

1.2.2 Hazard symbols

Hazard symbols are symbolic representations which give an indication of the kind of danger. The following hazard symbols are used in this document:

	Hazard symbol Meaning
		General warning message
		Danger from electrical voltage
		Risk of explosion
		Danger of cuts
		Danger of crushing

i Concerning this document

Hazard symbol Meaning
		Danger from hot surfaces
		Danger from strong magnetic field
		Danger from non-ionizing radiation

Table 2: Hazard symbols

1.2.3 Structure of the warnings

Warnings in this document have a standardised appearance and a standardised structure.

Type and source of danger!

Possible consequences of ignoring the danger / warning.

▶ Measures and prohibitions for preventing the danger.

The following example shows a warning that warns against electric shock due to live parts. The measure for avoiding the danger is mentioned.

Risk of electric shock due to live parts!

Death by electrocution

- Disconnect appliances from electrical supply at least 60 seconds before starting repairs.

1.2.4 General symbols

The following general symbols are used in this document:

Gen. symbol Meaning
	Identification of a special tip (text and/or graphic)
	Identification of a simple tip (only text)
	Identification of a link to a video tutorial

Gen. symbol Meaning
	Identification of required tools
	Identification of required preconditions
	Identification of a condition (if ..., then ...)
	Identification of a result
[Start] Identification of a key or button
[00123456] Identification of a material number
Status Identification of displayed text / window(in the appliance's display)

Table 3: General symbols

Safety

2.1 General Safety instructions

2.1.1 All domestic appliances

Risk of electric shock due to live parts!

• Errors by repairs involving electrical components can lead to electrical shock! ■ Disconnect the appliance from the mains for at least 60 seconds before starting work. ■ After the repair have a safety test according VDE 0701 or country-specific regulations performed.

Risk of injury from sharp edges!

■ Wear protective gloves.

Risk of crushing during repair, maintenance, troubleshooting and service due to heavy and moving components

■ Wear protective shoes. ■ Secure heavy components from falling down. ■ Do not stick body parts into moving components.

Risk to the appliance's safety / function!

■ Only use original spare parts.

Risk of damage to electrostatically sensitive components (ESDs)!

- Do not touch the modules, including connections and conductor paths.

Tools and aids

Designation Details Images
Protection cloth[00342013]	60 cm x 50 cm
Torx Bit TX20[00340865]	6,3 mm (1/4")
Special tool[00342180]

Repair

1. Release door gasket from the groove on right and left corner.

1. Pull out door gasket from groove.

Door gasket is removed.

	Thickness of new door gasket may deviate slightly from thickness of old door gasket. This will not affect closing behavior and long-term function.
	If your appliance has adjustable hinges or hinge attachments, you can optimize the closing behavior subsequently.
	Small side holes in door gasket are functional (required for ventilation). These are not production faults.

Repair

1. Check groove for gasket for damage.

1. If the groove for the gasket is damaged.
2. Contact customer service.
3. i Slight deformation of door gasket is normal and does not affect its function. It is recommended to straighten door gasket before inserting it into appliance.

Heat door gasket with a hair dryer or hot water and manually reshape it.

1. Push corners of gasket at the top and bottom to the groove.

Repair

1. Press whole gasket step by step into the groove.

Door gasket is installed.

Repair

4.2 Replacing flat hinge

Required tools:

Torx Bit TX20 6,3 mm (1/4") [00340865]

Prerequisite:

√ Appliance is disconnected from power supply. √ Furniture door are removed. See Installation Instruction. √ Door is open.

1. Remove four hinge covers.

Repair

2.1. Loosen four screws (1).

1. Slide out and remove upper door (2).

1. Remove four screws (1).
2. Remove hinges (2).

Upper door hinges are removed.

1. Loosen four screws (1).
2. Slide out and remove lower door (2).

1. Remove four screws (1).
2. Remove hinges (2).

Lower door hinges are removed.

Repair

4.2.2 Installing flat hinge

Install in reverse order.

Repair

4.3 Replacing sliding hinge

Required tools:

Torx Bit TX20 6.3 mm (1/4") [00340865]

Prerequisite:

Appliance is disconnected from power supply. Furniture door and appliance door are separated. See Installation Instruction.

4.3.1 Removing sliding hinge

1. Unscrew two screws (1).
2. Remove upper door upper hinge (2).
3. Remove upper door (3).
4. Unscrew two screws (4).
5. Remove lower door upper hinge (5).
6. Remove lower door (6).

Repair

1. Remove four screws (1).
2. Remove lower hinges (2).

Hinges are removed.

4.3.2 Installing sliding hinge

Install in reverse order.

Repair

4.4 Replacing door rack

Prerequisite:

Door is open.

Lift door rack upwards.

Door rack is removed.

Install in reverse order.

Repair

4.5 Replacing shelf

Prerequisite:

Door is open.

4.5.1 Removing shelf

Pull out shelf.

Shelf is removed.

4.5.2 Installing shelf

Install in reverse order.

Repair

4.6 Replacing extendable shelf

Prerequisite:

Door is open.

4.6.1 Removing extendable shelf

1. Pull out extendable shelf until the locking catch is released.

1. Lower extendable shelf and swing it out to the side.
2. Extendable shelf is removed.

4.6.2 Installing extendable shelf

Install in reverse order.

Repair

4.7 Replacing freezer compartment shelf

Prerequisite:

Door is open.

4.7.1 Removing freezer compartment shelf

Pull out freezer compartment shelf.

Freezer compartment shelf is removed.

4.7.2 Installing freezer compartment shelf

▶ Install in reverse order.

Repair

4.8 Replacing frozen food container

Prerequisite:

Door is open.

4.8.1 Removing frozen food container

1. Pull out frozen food container all the way (1).
2. Remove frozen food container (2).

Frozen food container is removed.

4.8.2 Installing frozen food container

▶ Install in reverse order.

Repair

4.9 Replacing fruit and vegetable container

Prerequisite:

Door is open.

4.9.1 Removing fruit and vegetable container

1. Pull container out all the way (1).

1. Remove container (2).

Container is removed.

4.9.2 Installing fruit and vegetable container

Install in reverse order.

Repair

4.10 Replacing partition and cover of fruit and vegetable container

Prerequisite:

Door is open.

4.10.1 Removing partition and cover of fruit and vegetable container

1. Remove glass plate from partition.

1. Remove fruit and vegetable container. See page 140.
2. Press the lever on the underside on both partition sides (1).
3. Pull the partition forwards (2).

1. Lift the partition and swivel it out to the side.

The partition is removed.

1. Lift the cover of the fruit and vegetable container.
2. Pull the cover of the fruit and vegetable container forwards and swivel it out to the side.

The cover of the fruit and vegetable container is removed.

4.10.2 Installing the partition and cover of the fruit and vegetable container

Install in reverse order.

Repair

4.11 Replacing the cool-fresh container

Prerequisite:

√ Door is open.

4.11.1 Removing cool-fresh container

▶ 1. Tilt cool-fresh container forwards (1). 2. Remove cool-fresh container (2).

Cool-fresh container is removed.

4.11.2 Installing cool-fresh container

▶ Install in reverse order.

Repair

4.12 Replacing extendable container

Prerequisite:

√ Door is open.

4.12.1 Removing extendable container

▶ 1. Tilt extendable container forwards (1). 2. Remove extendable container (2)

Extendable container is removed.

4.12.2 Installing extendable container

▶ Install in reverse order.

Repair

4.13 Replacing LED spot light

Required tools:

Special tool [00342180]

Slotted screwdriver Blade 2.4 mm x 0.4 mm x 60 mm, in the kit [00341820]

Your appliance features a maintenance-free LED light. These lights may be repaired by customer service or authorized technicians only!

Risk of electric shock due to live parts!

Danger to life through electric shock in case of improper repair

▶ Electric parts should be repaired by a qualified electrician.

After the repair, have a safety test performed according to VDE 0701 or country-specific regulations.

Risk of electric shock due to live parts!

Death by electrocution

- Disconnect appliances from electrical supply at least 60 seconds before starting repairs.

Sharp edges!

Cut injuries

Wear protective gloves.

Prerequisite:

Appliance is disconnected from power supply. Door is open. Fridge compartment shelves are removed.

4.13.1 Removing LED spot light

1. Release LED spot light cover.

1. Pull LED spot light cover inwards and simultaneously push forwards.

Repair

1. Detach LED spot light module.

1. Disconnect LED spot light electrical connection.

LED spot light is removed.

4.13.2 Installing LED spot light

Install in reverse order.

1.1.1 Purpose 147

1.2 Explanation of symbols 147

1.2.1 Hazard levels.... 147

Repair

1. Press the entire gasket into the groove piece by piece.

1. Remove the four hinge covers.

Repair

Repair

1. Remove the four screws (1).
2. Remove the lower hinges (2).

Repair

Repair

Repair

Repair

The shelf has been removed.

The Cool-fresh compartment has been removed.

4.11.2 Installing the Cool-fresh compartment

Repair

1. Remove the LED spotlight module.

1. Remove the door gasket from the groove.

Repair

Repair

Repair

The drawer has been removed.

Repair

Repair

Repair

Repair

Repair

Repair

Repair

Repair

The door panel has been removed.

The panel has been removed.

The drawer has been removed.

Repair

Repair

Repair

Repair

Repair

Repair

Repair

Repair

Repair

Removal

Removal

Removal

The screw has been removed.

The shelf has been removed.

The container has been removed.

4.9.2 Installation of the fruit and vegetable container

1. Lift the spacer and tilt it to the side to remove it.

Repair

1. Disconnect the LED spotlight module.

1. Disconnect the electrical connection of the LED spotlight.

The LED spotlight has been removed.

Repair

Repair

Repair

Hinges removed.

Shelf removed.

Container removed.

Repair

Repair

Risk of crushing/pinching fingers

Repair

The lower door hinges are disassembled.

Repair

Repair

1. Remove four screws (1).
2. Disassemble lower hinges (2).

The shelf in the freezer is disassembled.

4.7.2 Assembling the shelf in the freezer

→ The container for frozen goods is disassembled.

The container is disassembled.

The Cool-Fresh container is disassembled.

The LED spotlight is disassembled.

Repairs

Repairs

Repairs

The shelf is removed.

4.5.2 Assembling the shelf

Repairs

Repair

Repair

1. Remove four screws (1).
2. Remove the hinges (2).

1. Remove four screws (1).
2. Remove the hinges (2).

Repair

1. Remove four screws (1).
2. Remove the lower hinges (2).

Repair

Repair

Torx TX20 6.3 mm (1/4") socket [00340865]

Repair

The hinges of the upper door are disassembled.

The hinges of the lower door are disassembled.

Repair

4.2.2 Mounting the flat hinge

Torx TX20 6.3 mm (1/4") [00340865]

Repair

The hinges are disassembled.

4.3.2 Mounting the sliding hinge

Repair

1. Pull the seal out of the groove.

Repair

The door seal is installed.

Repair

Repair

Repair

The hinges have been removed.

The shelf in the door has been removed.

4.4.2 Installing the shelf in the door

The freezer compartment shelf has been removed.

4.7.2 Installing the freezer compartment shelf

The container has been removed.

1. Remove the fruit and vegetable container.→476
2. Press the lever on the underside of both sides of the compartment (1).
3. Pull the compartment forward (2).

1. Lift the compartment and tilt it to the side.

The compartment has been removed.

The cool-fresh container has been removed.

Repair

1. Pull the door seal out of the groove.

Repair

1. Push the entire seal into the groove step by step.

Back and muscle injuries

Repair

Back and muscle injuries

Repair

1. Remove the four screws (1).
2. Remove the lower hinges (2).

The shelf is removed.

4.5.2 Installing the shelf

- Install in reverse order.

Repair

1. Remove the fruit and vegetable drawer.→500
2. Press the fasteners on the underside of the glass panel (1).
3. Pull the divider towards you (2).

1. Lift the divider and remove it by turning it sideways. → The divider is removed.
2. Lift the shelf above the fruit and vegetable drawer.
3. Pull the shelf above the fruit and vegetable drawer towards you and remove it by turning it sideways. → The shelf above the fruit and vegetable drawer is removed.

4.10.2 Installing the divider and the shelf above the fruit and vegetable drawer

▶ Install in reverse order.

Repair

1. Pull the LED spot light cover inwards and push it forward at the same time.

Repair

Repair

Repair

Repair

Repair

Repair

Repair

Repair

The door shelf has been removed.

4.4.2 Mounting the door shelf

The freezer compartment shelf has been removed.

4.7.2 Mounting the freezer compartment shelf

The Cool Fresh compartment has been removed.

4.11.2 Mounting the Cool Fresh compartment

Repair

1. Remove the LED spotlight module.

1. Disconnect the electrical connection of the LED spotlight.

The LED spotlight has been removed.

4.13.2 Mounting the LED spotlight

Repair

Repair

Repair

The cover has been removed.

Special tool [00342180]

Flat screwdriver, blade 2.4 mm x 0.4 mm x 60 mm,

Repair