FP-650 - Planer Ferm - Free user manual and instructions

Product Type	Planer
Brand	Ferm
Model	FP-650
Voltage	230 V~
Frequency	50 Hz
Power Consumption	650 W
No-Load Speed	16000 min⁻¹
Max Planing Depth	2 mm
Max Planing Width	82 mm
Weight	2.6 kg
Sound Pressure Level (LpA)	85.3 dB(A)
Sound Power Level (LwA)	96.3 dB(A)
Vibration Value	2.56 m/s²
Insulation Class	Double insulated (no earth wire required)
Drive System	V-belt driven single-phase motor
Depth Adjustment	Rotary knob with mm scale (0-2 mm)
Blade Type	Replaceable planer blade (ref. PPA1003)
Carbon Brushes	Replaceable set (ref. 406534); check every 100 h; replace if <4 mm
Safety Features	Release button (safety lock), double insulation, dust extraction port
Maintenance	Clean housing with damp cloth; keep air vents clean; no extra lubrication needed
Included Accessories	Open-jawed spanner for blade replacement
Application	Planing wooden beams or boards; manual operation
Standards Compliance	EN60745-2-14, EN60745-1, EN55014-1, EN55014-2, EN61000-3-2, EN61000-3-3

Frequently Asked Questions - FP-650 Ferm

What is the maximum planing depth of the Ferm FP-650 planer?

The maximum planing depth is 2 mm. Adjust it using the depth control knob with a scale in millimeters.

How do I replace the planer blade on the FP-650?

Disconnect the power. Use the supplied open-jawed spanner to loosen the three clamping screws. Remove the blade holder, blade, and support. Install a new blade (ref. PPA1003) between support and holder, tighten the screws firmly. Ensure all parts are clean.

What is the power consumption of the Ferm FP-650?

The power consumption is 650 W at 230 V~, 50 Hz.

Does the Ferm FP-650 require an earth connection?

No. The tool is double insulated according to EN 60745, so no earth wire is needed.

How often should I replace the carbon brushes?

Check the carbon brushes approximately every 100 running hours. Replace them if they are shorter than 4 mm (use Ferm set ref. 406534).

What can cause the motor to overheat?

Possible causes: foreign substances in the motor, contaminated lubricating grease, excessive pressure during use, or a blunt planing blade. Reduce pressure and inspect the blade.

The motor runs but the blade does not turn. What is wrong?

This may indicate a worn V-belt. Have the belt replaced by a qualified service center (Ferm part no. 406530).

Can I use the planer on workpieces other than wood?

The planer is intended for wooden beams or boards only. Do not use on metal, plastic, or other materials.

What safety precautions should I take when using the FP-650?

Always wear a dust mask, secure the workpiece with clamps, never touch the workpiece during operation, wait for the cutter to stop before setting the tool down, and disconnect the mains before maintenance.

Where can I find spare parts for the Ferm FP-650?

Spare parts are listed in the exploded view and parts list in the manual. Contact the Ferm service address on the warranty card or use authorized dealers. Use only original Ferm parts.

USER MANUAL FP-650 Ferm

GB Subject to change

D Änderungen vorbehalten
NL Wijzigingen voorbehouden
F Sous réserve de modifications
E Reservado el derecho de modificaciones técnicas
P Reservado o direito a modificações
I Con riserva di modifiche
S Ändringar förbehålles
FIN Pidätämme oikeuden muutoksiin
N Rett till endringer forbeholdes
DK Ret til ændringer forbeholdes

Black industrial machine labeled 'CT TOOL' with visible metal frame and handle (no readable text beyond label)

GB USERS MANUAL 03
D GEBRAUCHSANWEISUNG 06
NL GEBRUIKSAANWIJZING 10
F MODE D'EMPLOI 14
E MANUAL DE INSTRUCCIONES 18
P ISTRUÇÖNAUSAR 22
1 MANUALE UTILIZZATI 26
S BRUKSANVISNING 30
FIN KÄYTTÖOHJE 34
N BRUKSANVISNING 37
DK BRUGERVEJLEDNING 40
H HASZNÁLATIUTASÍTÁS 44
CZ NÁVOD KPOUŽITI 48
SLO NOVODILAZAUPORABO 51
PL INSTRUKSJE OBSŁUGI 54
RUS РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ 58
GR ΟΔΗΓΙΕΣ ΧΡΗΣΕΩΣ 62

www.ferm.com

CE

DECLARATION OF CONFORMITY

FP-650 PLANER

(GB) We declare under our sole responsibility that this product is in conformity and accordance with the following standards and regulations:
(D) Der Hersteller erklärt eigenverantwortlich, dass dieses Produkt den folgenden Standards und Vorschriften entspricht:
(NL) Wij verklaren onder cnze volledige verantwoordelijkheid dat dit product voldoet aan, en in overeenslemming is met, de volgende standaarden en reguleringen:
(F) Nous déclarons sous notre seule responsabilité que ce produit est conforme aux standards et directives suivants:
(E) Declaramos bajo nuestra exclusiva responsabilidad que este producto cumple con las siguientes normas y estándares de funcionamiento:
(P) Declaramos por nossa total responsabilidade que este produto está em conformidade e cumpre as normas e regulamentações que se sequem:
(I) Dichiariamo, sotto la nostra responsabilità, che questo prodotto è conforme alle normative e ai regolamenti seguenti:
(S) Vi garanterar på eget ansvar att denna produkt uppfyller och följer följande standarder och bestämmelser:
(FIN) Vakuutamme yksincmaan omalla vastuullamme, etlä tämä luole lävltää seuraavai standardil ja saäröksei
(N) Vi erklærer under vart eget ansvar at dette produktet er i samsvar med følgende standarder og regler:
(DK) Vi erklærer under eget ansvar, at dette produkt er i overensstemmelse med følgende standarder og bestemmelser:

(H) Felelősségünk teljes tudalában kijelentjük, hogy ez a termék teljes mértékben megfelel az alábbi szabványoknak és előirásoknak;
(CZ) Na naši vlastní zodpovědnost prohlasujeme, že je tento výrobek v souladu s následujícími standardy a normami:
(SK) Vyhlasujeme na našu vyhradnu zodpovednosť, že tento výrobok je v zhode a súlade s nasledujúcimi normami a predpismi:
(SLO) S polno odgovomostjo izjavljamo, da je ta izdelek v skladu in da odgovarja naslednjim standardom ter predpisom:
(PL) Deklarujemy na własną odpowiedzialność, że ten produkt spełnia wymogi zawarte w następujących normach i przepisach:
(LT) Prisiindami visą alsakomybę deklaruojame, kad śis gaminys atilinka żemiau paminétus standartus arba nuostatus:
(LV) Apgalvojam ar visu atbildību, ka šis produkts ir saskaņā un atbilst sekojošiem standartiem un nolikumiem:
(EST) Deklareerime meie ainuvastutusel, et see toode on vastavuses ja kooskõlas järgmiste standardite ja määrustega:
(RO) Declaram prin aceasta cu răspunderea deplină că produsul acesta este în conformitate cu următoarele slandarde sau directive:
(RUS) Под свою ответственность заяпляем, что данное изделие соответствует следующим стандартам и нормам:
(UA) На свою власну зідповідальність заявляемо, що дане обладнання відповідве наступним стандартам і нормативам:
(GR) Δηλώνουμε υπείθυνα ότι το προϊόν αυτό συμφωνεί και τηρεί τους παρακάτω κανονισμούς και πρότυπα:

EN60745-2-14, EN60745-1, EN55014-1, EN55014-2, EN61000-3-2, EN61000-3-3

98/37/EC, 2002/95/EC, 2002/96/EC, 2004/108/EC, 2006/95/EC

Zwolle. 01-09-2008

J.A. Bakker - van Ingen CEO Ferm BV

J. Lodewijk Quality Manager Ferm Global

It is our policy to continuously improve our products and we therefore reserve the right to change the product specification without prior notice.

Ferm BV • Lingenstraat 6 • 8028 PM • Zwolle The Netherlands

Ferm 7102 Ferm

EXPLODED VIEW

Spare parts list FP-650

Ferm no.	Description	Position no.
406530	Belt	3
806200	Bearing 6200 zz	8
406531	Upper pressing bar complete 11 t/m 13
PPA1003	Planer blade	14
406532	Lower pressing board	15
406533	Switch	17
406534	Carbon brush (set)	28
406535	Stator	36
406536	Rotor	39
800628	Bearing 628 zz	42
800626	Bearing 626 zz	43
800608	Bearing 608 zz	44

PLANER

The numbers in the following text correspond with the pictures at page 2.

Read through these operating instructions carefully before using the appliance. Become familiar with the functions and method of operation. To ensure proper operation, always maintain the appliance according to the instructions. The operating instructions and associated documents should always be kept close to the appliance.

intended use

This doubly insulated electric tool is designed to be manually operated. It has an appealing shape and small dimensions, which facilitate easy transportation. It is safe and reliable when in operation. It is driven by a single phase electric motor via a V-belt. It is suitable for planing wooden beams or boards.

Contents

1. Machine data
2. Safety instructions
3. Assembly and operation
4. Maintenance

1. MACHINE DATA

Technical specifications

Voltage | 230 V~
Frequency | 50 Hz
Power consumption | 650 W
Number of revolutions, idle | 16000/min
Maximum planing depth | 2 mm
Maximum planing width | 82 mm
Weight | 2.6 kg
LpA (sound pressure)	| 85.3 dB(A)
LwA (sound capacity)	| 96.3 dB(A)
Vibration value	| 2.56 m/s ^2

Parts list

(Fig. 1)

A Control knob for adjustment of planing depth
B Indication of planing depth
C Cover, right
D Operating Switch
E Release Button
F. Handle
G Cover, left

2. SAFETY INSTRUCTIONS

The following pictograms appear throughout these operating instructions:

Indicates danger of injury, risk to life and possible damage to the appliance if these instructions are not followed.

Wear a dust mask

Indicates the presence of electrical current.

When using power tools, you must observe the following basic safety precautions in order to ensure protection from electric shocks, injury and fire. Read and follow all the instructions before using this power tool. Look after the notes on safety.

Electrical safety

Always check if your mains voltage corresponds with the value on the type plate.

The machine has been double-insulated in accordance with EN 60745; therefore, an earth wire is not necessary.

When replacing old cables or plugs

Throw away old cables or plugs immediately as soon as new ones have replaced these. It is dangerous to put the plug of a loose cable into the socket outlet.

When using extension cables

Only use an approved extension cable that is suitable for the machine's power. The cores must have a diameter of at least 1.5 mm ^2 . When the extension cable is on a reel, unroll the cable in its entirely.

Switch off the machine immediately in case of

1. Malfunction in the mains plug, power cable or damaging of cable.
2. Broken switch.
3. Smoke or stench of scorched insulation.

Wait for the cutter to stop before setting the tool down. An exposed cutter may engage the surface leading to possible loss of control and serious injury.

3. ASSEMBLY AND OPERATION

Before setting up, repair or maintenance of the appliance you must always turn off the operating switch and pull out the mains plug!

Before initial operation

• Check if the rated voltage and rated frequency of the mains supply correspond to the details of the type plate.
• Place the workbench on a stable and even base.

Operation

- To adjust the planing depth, turn the control knob (Fig. 1, A) in a clockwise direction. On the control knob there is a pointer (Fig. 1, A) which shows the planing depth in mm. Turn the control knob until the desired planing depth is shown.

Never alter the planing depth during an operating cycle, otherwise this will result in an uneven surface. To prevent operating errors turn the control knob back to "0" when planing is completed.

• Secure the work piece with clamps or similar.
• Place the front sole on the edge of the work piece in such a way that the planing tool does not yet touch the work piece. The work piece must be level.
• Now insert the mains plug into the socket. To switch on, first press the release button (Fig. 1,E), keep it pressed down while you press the operating switch (Fig. 1,D). The appliance is now switched on and you can let go of the release button.
• When the machine has reached full speed it can be pushed to the front over the work piece. At the beginning of the planing operation, put some pressure on the front and at the end of the operation, on the rear of the appliance. This results in the appliance remaining flat on the work piece and prevents

the corners from getting rounded off.

• To obtain a level and smooth surface use a greater planing depth when rough planing and a lesser planing depth when planing a layer. Hold the electric tool straight during the operation, otherwise you will obtain an uneven surface. After the operation switch off the electric tool and remove the mains plug.

WARNING!

1. Take care that your hand never comes in contact with the work piece during the operation.
2. Only use the electric plane on the upper side of the work piece, never from below or from the side.
3. Store the appliance only after it has come to a complete standstill.
4. Use a suction device to suck off wood shavings or dust. For this use the connecting pipe and connect a suction pipe to it.
5. Use a holding device to work on small work pieces.

Care and maintenance

Before undertaking any care or maintenance always remove the mains plug from the socket.

The planing tool becomes worn after a period of operation. If you use a blunt or damaged planing tool operational efficiency is reduced and the electric motor might become overloaded. Check the planing tool regularly with regard to wear or damage. Depending on its condition, the planing tool will have to be replaced.

Removal of plane blade

(Fig.2)

Use the enclosed open-jawed spanner (Accessories). First unscrew the three clamping screws (6) with the open-jawed spanner and remove the plane blade (3), the plane blade holder (2) and the plane blade support (4) from the holding shaft (1).

installation of plane blade

(Fig.2)

Take the new plane blade (3) and position it between the plane blade support (4) and the

plane blade holder (2). Now turn the clamping screws (6) as far as possible into the plane blade support. But not so far that the plane blade and the plane blade holder become detached again from the plane blade support. Afterwards put the plane blade, plane blade holder and plane blade support together into the holding shaft. The plane blade support, plane blade and plane blade holder will now be fastened together in the holding shaft by releasing the clamping screws with the open-jawed spanner and thus the plane blade, plane blade support and plane blade holder are clamped in position.

Attention:

Unscrew clamping screws as fas as possible so that a sufficient attachment is ensured.

Warning!

1. When installing and removing the plane blade, care has to be taken that all parts (plane blade, plane blade holder, plane blade support and holding shaft) are clean. Dirt or possible existing layers of dirt have to be removed.
2. The Allen screws (5) are secured with an adhesive. These screws must not be adjusted. The position of these screws may only be altered by the manufacturer!

Check regularly if the clamping screws are tightened firmly. Always tighten screws firmly.

Replacement of the carbon brushes

The carbon brushes can become worn after frequent use. A regular check after about every 100 running hours is therefore necessary. If the carbon brushes are shorter than 4 mm then these will have to be replaced with new ones.

• Remove the cover on the right.
• Take out the carbon brushes and check these.
• Replace the carbon brushes.
• Replace the two screws and screw them tight.

Corrective action in case of failure

1. The operating switch is switched on, but the motor is not working.

2. The electric circuit is broken. Have the electric circuit repaired.

3. Wires in the mains plug or in the socket are loose.
   Have socket and plug checked or repaired.

4. The switch is faulty. Have the switch replaced.

5. The operating switch is switched on, but unusual noises can be heard, the motor is not working or only very slowly.

6. Switch contact has fused. Have the switch replaced.

7. Component jammed. Have the electric tool checked or repaired.
8. Too much thrust, as a result the motor is dragging. Use less thrust during the task.
9. Too much thrust, as a result the motor is dragging.
   Use less thrust during the task.

3. Motor gets hot.

• Foreign substances have got inside the motor. Have the foreign substances removed.
• Lack of or contaminated lubricating grease. Have lubricating grease applied or replaced.
• Pressure too high. Use less thrust during the task

• Planing tool blunt. Replace the planing tool.

• The motor is working, but the planing tool is not moving.

- V-belt worn. Have V-belt replaced.

1. Frequent or strong sparks on the commutator.

2. Short circuit on the armature. Have the armature repla

3. Carbon brushes worn out or jammed Have the carbon brushes checked.

- Rough running of the commutator. Have the surface of the commutator cleaned or ground

For your own safety, never remove parts or accessories of the electric tool during operation. In case of fault or damage have the electric tool repaired only by a specialist workshop or by the manufacturer.

Caution!

Use only original spare parts and original plane blades!

4. MAINTENANCE

Make sure that the machine is not live when carrying out maintenance work on the motor.

These appliances are designed to function without difficulty for a long time and to require minimum maintenance. You will prolong the appliance's life by cleaning it regularly and using it correctly.

Cleaning

Clean the housing regularly with a soft cloth, preferably every time it is used. Keep the air vents free of dust and dirt. Remove stubborn dirt with a soft rag moistened in soapy water. Do not use any solvents such as petrol, alcohol, ammonia, etc. as such substances can damage the plastic parts.

Lubrication

The appliance does not need any extra lubrication.

Faults

If a fault arises through wear in an element, please contact the service address shown on the warranty card.

A drawing of the spare parts that may be obtained is included at the end of these operating instructions.

Environment

To prevent damage during transport, the appliance is delivered in a solid packaging which consists largely of reusable material. Therefore please make use of options for recycling the packaging.

Faulty and/or discarded electrical or electronic apparatus have to be collected at the appropriate recycling locations.

Warranty

Read the terms of warranty on the separate warranty card which is enclosed. Please contact the Ferm service address if you have any questions regarding accessories and/or batteries.

HOBELMASCHINE

Specifications techniques

The Ground Truth image displays a single, solid horizontal line. According to Rule 2 (UNDERSCORE & LINE RULES), this is a stylistic or background line, not a placeholder underscore. Therefore, the OCR result must ignore it and output nothing or only meaningful text. The provided OCR content is "____", which consists of four underscores. This is an incorrect interpretation of the line as a placeholder, violating the rule that stylistic lines must be ignored. The OCR has hallucinated placeholder underscores where none exist in the GT. Hence, the result is inconsistent with the Ground Truth.