MSR801 - Beard trimmer BLAUPUNKT - Free user manual and instructions

Product Type	Beard Trimmer / Shaver
Model	MSR801
Brand	Blaupunkt
Power Supply Input	100-240V~50/60Hz, 0.2A
Power Supply Output	5V, 1000mA
Battery Type	Rechargeable with percentage display
Usage Modes	Wet and dry, cordless or corded
Attachments	Shaving head, trimmer attachment, limit combs (multiple lengths)
Speed Settings	High (Hi) and Low (Low)
Cleaning	Rinse under running water (max 50°C); brush included
Maintenance	Apply machine oil to blades regularly
Safety Compliance	CE, LVD, EMC
Warranty & Support	Contact service: [e-mail], [phone]
Intended Use	Domestic only, not for commercial use

Frequently Asked Questions - MSR801 BLAUPUNKT

How do I charge the MSR801 beard trimmer?

Insert the power supply cord into the appliance and connect the power supply unit to an electrical outlet (100-240V). The display will show the charging status. If fully discharged, charging indication may be delayed up to 2 minutes.

Can I use the trimmer while it is charging?

Yes, you can continue using the appliance while connected to the charger. However, do not use it near baths, showers, or pools when charging.

How should I clean the beard trimmer?

Ensure the appliance is switched off and unplugged. Use the included brush to clean the shaving film and blades after each use. The blades can also be rinsed under running water (max 50°C). For deep cleaning, remove the shaving head and clean each head and blade set separately.

How do I replace the blades or shaving head?

Press the button to open the housing. Remove the mounting ring by turning it left. Remove each head and blade set. Place new blades in their assigned heads, then reinstall the ring and turn it right to close.

How can I trim different beard lengths?

Attach the trimmer attachment, then select the appropriate limit comb. The cut length is indicated on the side of the comb. Switch on and move slowly against the hair growth.

Can I use the trimmer in the shower?

The appliance is suitable for wet use, but only when it is not connected to the charger. Do not use it corded in wet conditions. It can be rinsed under running water.

What should I do if the battery does not charge?

First, check that the power supply is properly connected. If fully discharged, allow up to 2 minutes for the display to show charging. If still not charging, contact service at [e-mail].

How do I oil the blades?

After cleaning the blades, apply a small amount of machine oil onto them. This is recommended to maintain performance and prevent wear.

Is the trimmer suitable for both dry and wet shaving?

Yes, the appliance can be used for wet shaving with foam or gel, as well as dry shaving. Rinse regularly under water to prevent clogging.

How long does it take to adjust to the shaver?

The first few shaves may not be perfectly accurate and skin might be irritated. This adjustment period can last up to 3 weeks as your skin and hair adapt to the blade system.

USER MANUAL MSR801 BLAUPUNKT

Black and white BLASPUNT electric shaver with digital display (no visible text or symbols)

Enjoy it.

Man's shaver 3in1

Golarka męska 3w1

- Before using this device read the instruction manual and follow the instructions inside. The manufacturer is not liable for any damages caused by the misuse of this device due to inappropriate handling. Please keep this manual for future reference.

- This device is for domestic use only. Do not use for any other purposes.

- The device should be cleaned regularly complying with the recommendations described in the section on cleaning and maintenance.

- Do not place the device near sources of heat, flame, an electric heating element or a hot oven. Do not place on any other device.

- This equipment can be used by children aged 8 years and over under as long as supervision is provided. People with reduced physical or mental capabilities, as well as people with no previous experience of using this equipment must be supervised and made aware of the risks. The instruction manual should be used as a reference for the safe use of this equipment. Children should not play with the equipment. Children without ensured supervision should not be allowed to perform the cleaning and maintenance of equipment.

• Additional precautions should be taken when using this device in the presence of children or pets. Do not allow children to play with the device.

- Never use the product close to combustibles.

- Never expose the product to atmospheric conditions such as direct sun light or rain, etc... Never use the product in humid conditions (like bathroom or camping house).

- Only Original accessories should be used, as well as

accessories recommended by the manufacturer. Using accessories which are not recommended by the manufacturer may result in damage of the device and may render the device unsafe for use.

- The AC adapter should be connected to an outlet with characteristics consistent with the values on the rating label.

- If the cord or power plug or adaptor is damaged or the plug has a loose electrical outlet, do not charge the device and do not power it from the mains.

- Unplug the AC adapter from the electrical outlet when not in use.

- Do not connect or disconnect the adaptor from the power source with wet hands.

- This device uses only the power adapter supplied with the device or recommended by the manufacturer.

• Having disconnected the appliance from the power supply, clean it under running water no warmer than 50 degrees.

- Only a wireless appliance may be used in the bath or shower.

- Do not use the shaver if the film or blades are damaged in any way.

- Do not use the appliance if the blades or any element of the trimming head is damaged.

- The appliance may be charged in temperatures in the range of 5-35 degrees Celsius.

- For reasons of hygiene, the appliance should be used by one person only.

CE

Device is compliant with EU directives:

• Low voltage directive (LVD)
• Electromagnetic compatibility (EMC)
  Device marked CE mark on rating label

When this crossed-out wheeled bin symbol is attached to a product it means that the product is covered by the European Directive 2012/19/EU. Please inform yourself about the local separate collection system for electrical and electronic products. Used appliance should be delivered to the dedicated collecting points due to hazardous components, which may affect the environment. Do not dispose this appliance in the common waste bin.

Your product contains batteries covered by the European Directive 2006/66/EC, which cannot be dispose with normal household waste. Please inform yourself about the local rules on separate collection of batteries because correct disposal helps to prevent negative consequences for the environmental and human health.

Environmental information

All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and poly ethylene (bags, protective foam sheet). Your system consists of material which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment.

Your products is designed a manufactured with high quality materials and components, which can be recycled and reused.

TECHNICAL SPECIFICATIONS OF THE POWER SUPPLY UNIT

Input voltage: 100-240V\~50/60Hz

Maximum input current: 0,2A

Output voltage: 5V

Maximum output current: 1000mA

TECHNICAL SPECIFICATIONS OF THE APPLIANCE

Voltage: 5V

Max. input current: 1000mA

1. Shaving head
2. Housing of the shaving heads
3. Button opening the housing of the shaving heads
4. Shaving attachment
5. Trimmer attachment

6. Clipping blades

7. Speed switch (Hi – higher speed for more effective shaving and cutting harder hair, Low – gentler shaving and cutting hair)

8. On/Off button
9. Display (displays the percentage of battery charge)
10. Socket
11. Charging station
12. Power cord with a transformer (may be connected both directly to the shaver and to the charging station)

CHARGING THE APPLIANCE

If the appliance's battery charge is low or the battery is totally discharged, it needs charging. Insert the power supply cord into the appliance and connect the power supply unit to the electrical grid.

The charging indicator of the appliance will then display its charging status. If the appliance is totally discharged, the indication of its charging status may be delayed. This delay should be no longer than 2 minutes.

Having connected the appliance to the charger, you may continue using the appliance. However, do not use the appliance in the vicinity of baths, showers, swimming pools or similar water tanks.

SHAVER OPERATION

Place the shaving attachment on the main body of the appliance.

Switch the shaver on with the On/Off button.

Move the shaver across the skin surface, making circular movements.

Clean the shaving head after each use with the provided brush.

The appliance may be used for wet or dry shaving. If you use shaving foam or gel, rinse the shaver regularly under a stream of tap water to prevent the shaving head from "clogging".

Note: Each shaver requires the skin and hair growth to adjust to the blade system applied. The first shaves may not be perfectly accurate and the skin may be irritated. The adjustment period may last up to 3 weeks.

SHAVER CLEANING

Make sure the appliance is switched off and not connected to the charger.

Clean the shaving film and the shaver blades after each use of the shaver. Use the brush for this purpose. The blades may be rinsed under running water.

Clean the appliance regularly with due care. Press the button opening the housing of the shaving heads. Remove all hair from the inside. Turn the ring mounting the blade heads to the left. Remove the ring. Remove and clean each head and set of blades.

Note: place the blades in the heads they have been removed from (each blade is assigned to a respective head, and if used in another head, the blade may be less effective or even get damaged).

Having cleaned the heads, place them in the housing along with the blades (pay attention to the cuts and grooves), insert the mounting ring and close it by turning it to the right.

GROWTH TRIMMING (TRIMMER)

Place the trimmer attachment onto the main body of the appliance. Switch the shaver on with the On/Off button. Move the appliance slowly over your hair. It is recommended to shave "against the grain", against the direction of the hair growth.

Place the trimmer attachment on the main body of the appliance.

Select the appropriate limit comb (cut hair length is indicated on the side of the limit comb). Place the limit comb on the hair shaver.

Switch the shaver on with the On/Off button. Slowly move the appliance over the hair. It is recommended to shave "against the grain", against the direction of the hair growth.

Note: Make sure you remove any excess cut hair from the limit comb.

Having finished clipping, remove all hair from the trimming head.

HAIR CLIPPER CLEANING

Prior to cleaning the appliance, ensure that it is switched off and not being charged.

Clean the limit combs under running water.

Remove the limit comb of the trimmer. Remove the trimming head by pressing down gently on the blades, as shown in figure 3. Clean the parts under running water.

It is recommended that a little machine oil is applied onto the cleaned blades.

WAŻNE INFORMACJE

Electromagnetic compatibility (EMC)

02-801 Warsaw, Poland

phone: [phone]

e-mail: [e-mail]

www.blaupunkt.com

In case of questions or problems

please contact our service.

Tel. [phone]

E-mail: [e-mail]

All rights reserved. All brand names are registered trademarks of their respective owners. Specifications are subject to change without prior notice.

Enjoy it.