RSM1016 - Jigsaw Ferm - Free user manual and instructions

Product type	Jigsaw
Brand	Ferm
Model	RSM1016
Power	650 W
No-load speed	500 – 3000 min⁻¹
Blade stroke	20 mm
Blade type	T-shank
Orbital action	4 adjustable positions
Bevel	0° – 45° sole plate tilt
Max cutting depth wood	100 mm
Max cutting depth steel	10 mm
Weight	2.3 kg
Power supply	Mains 230 V ~ 50 Hz
Cable length	2 m
Sound level (LpA)	85 dB(A)
Vibrations (ah)	10.2 m/s²
Debris blower	Yes, adjustable
LED lighting	Yes
Blade fixation	Tool-less
Maintenance	Clean with a dry cloth; lubricate gears periodically
Spare parts	Replaceable carbon brushes, standard blades

Frequently Asked Questions - RSM1016 Ferm

How to change the blade of the Ferm RSM1016 jigsaw?

Unplug the tool. Turn the tool-less clamping lever located on the blade guide, insert the T-shank blade until it stops, then release the lever. Check that the blade is securely held.

How to adjust the cutting speed?

Use the speed adjustment wheel (usually located on the handle). Turn it to increase or decrease the speed. Adapt the speed to the material: wood -> high speed, metal -> low speed.

What is orbital action and how to use it?

Orbital action makes the blade oscillate forward in addition to the vertical movement, which speeds up cutting in wood. Set the orbital selector to 0 (no orbit) for clean cuts in metal or plastic, and to 1-3 for wood (the higher the orbit, the faster but less clean the cut).

Can I cut metal with the Ferm RSM1016 jigsaw?

Yes, provided you use a blade suitable for metal, set the speed to a low position and disable the orbital action. The maximum cutting depth in steel is about 10 mm.

How to clean and maintain the jigsaw?

Unplug the tool before any maintenance. Clean the housing with a slightly damp dry cloth (no solvents). Remove the blade and clean the blade holder. Periodically lubricate the gears with special tool grease. Check the condition of the carbon brushes every 50 hours of use.

What safety precautions should I take?

Always wear safety goggles and a dust mask. Use a clamp or vise to hold the workpiece. Do not wear loose clothing. Ensure the power cord is in good condition. Unplug the tool before changing the blade or making adjustments.

The jigsaw does not start, what to do?

Check that the outlet is powered and the cord is not damaged. Make sure the safety lock (if any) is disengaged. If the problem persists, the carbon brushes may be worn: they are accessible and replaceable. Contact after-sales service.

Can I use the jigsaw without dust extraction?

Yes, the dust extraction nozzle is removable. You can work without it, but the built-in debris blower helps clear the cutting line. For a healthier environment, connect a vacuum cleaner to the nozzle.

How to tilt the sole plate for a bevel cut?

Loosen the sole plate fixing screws (usually two screws at the front). Tilt the sole plate to the desired angle (0° to 45°). Use the angle mark if present. Tighten the screws. Note: the cutting depth is reduced when bevel cutting.

What types of blades are compatible with the RSM1016 model?

The jigsaw accepts standard T-shank blades. Choose the blade according to the material: wood (large teeth), metal (fine teeth), plastic (medium teeth). Avoid U-shank blades which are not compatible.

USER MANUAL RSM1016 Ferm

Line drawing of a hand using a clamp to adjust a mechanical component, with no text or symbols present.

RECIPROCATING SAW

Thank you for buying this Ferm product.

By doing so you now have an excellent product, delivered by one of Europe's leading suppliers. All products delivered to you by Ferm are manufactured according to the highest standards of performance and safety. As part of our philosophy we also provide an excellent customer service, backed by our comprehensive Warranty. We hope you will enjoy using this product for many years to come.

The numbers in the text refer to the diagrams on page 2

Read the operating instructions carefully before using this device. Familiarize yourself with its functions and basic operation. Service the device as per the instructions to ensure that it always functions properly. The operating instructions and the accompanying documentation must be kept in the vicinity of the device.

Contents

1. Machine information
2. Safety instructions
3. Mounting accessories
4. Operation
5. Service & maintenance

1. MACHINE INFORMATION

Technical specifications

Mains voltage 230 V~

Frequency 50 Hz

Power input 710 W

No-load speed 0-2500/min

Saw stroke 20 mm

Max. saw capacity wood 115 mm

Max. saw capacity plastic 115 mm

Max. saw capacity steel 5 mm

Weight 2.68 kg

LpA (sound pressure level) 88.8+3 dB(A)

LwA (sound power level) 99.8+3 dB(A)

Vibration 12.388+1.5 m/s ^2

Vibration level

The vibration emission level stated in this

instruction manual has been measured in accordance with a standardised test given in EN 60745; it may be used to compare one tool with another and as a preliminary assessment of exposure to vibration when using the tool for the applications mentioned

• using the tool for different applications, or with different or poorly maintained accessories, may significantly increase the exposure level
• the times when the tool is switched off or when it is running but not actually doing the job, may significantly reduce the exposure level

Protect yourself against the effects of vibration by maintaining the tool and its accessories, keeping your hands warm, and organizing your work patterns

Contents of packing

1 Reciprocating saw
1 Saw blade for wood 230 3TPI
1 Saw blade for steel 150 mm bi-metal 18TPI
1 Hexagonal key
1 Operating instructions
1 Safety instructions
1 Warranty card

Check the appliance, any loose parts and accessories for damage caused during transport.

Product information

Fig. A

1. Foot plate
2. Saw buckle
3. On/Off switch
4. Lock on knob
5. Footplate mounting screws
6. Saw blade for wood
7. Saw blade for metal

2. SAFETY INSTRUCTIONS

Explanation of the symbols

Denotes risk of personal injury, loss of life or damage to the tool in case of non-observance of the instructions in this manual.

Indicates electrical shock hazard.

Wear a dust mask. Working with wood, metals and other materials may produce dust that is harmful to health. Do not work with material containing asbestos!

The number of revolution of the machine can be electronically set.

Safety instructions

The machine must not be damp and must not be operated in a wet environment. Wear protective gloves and sturdy footwear.

Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring or its own cord.

Cutting accessory contacting a "live" wire may make exposed metal parts of the power tool "live" and could give the operator an electric shock.

Do not saw materials containing asbestos!!!

Wear protective goggles when working with • materials which produce large amounts of chips.

Wear a protective mask when sawing other • fibrous materials.

Remove adjusting keys and wrenches before turning the tool on.

Secure your workpiece with clamps.

Move machine towards the workpiece only • when switched on.

Always hold machine with both hands and ensure that you have a safe footing while working.

The machine may be operated only with the foot plate mounted. When sawing, the foot plate must always rest on the workpiece.

Incorrect handling may damage the machine.

Therefore always comply with the following instructions.

Use only sharp saw blades in perfect • condition; replace cracked, distorted or blunt saw blades immediately.

Machine should only be switched on with blade installed

Select tools, stroke rate and pendulum • actions according to material, Take care to maintain a constant reed rate.

Do not attempt to stop the saw blade with lateral pressure after switching off.

• Only use genuine accessories.

3. MOUNTING ACCESSORIES

Fitting a saw blade

Fig. B

The machine is equipped with a quick fit system.

Turn the clamping ring (2) of the saw blade • holder as far to the left as possible and hold it there.

• Place the saw blade in the blade holder.
  • Let go of the clamping ring.
  Make sure when changing the saw blade that the blade holder is free of material debris (such as splinters of wood or metal).
• Before use, always check that the saw blade is securely fixed.

Removing the saw blade

• Turn the clamping ring of the saw blade holder as far to the left as possible and hold it there.
• Remove the saw blade from its holder.
  • Let go of the clamping ring.

Adjustment of the guide shoe

Fig. A

When the blade loses its sharpness at some sections of it's cutting edge, reposition the foot plate to use a sharp, unused portion of its cutting edge. Besides this, the foot plate can also be used for adjusting maximum saw depth, especially useful when sawing in hollow walls.

- The footplate can be extended by loosening the two footplate mounting screws (5) using the 4 mm hexagon key and then pulling the footplate out to the required length.

Ensure the footplate adjustment screws are secure before resuming work.

4. OPERATION

Always follow the safety notes and the relevant safety code.

Make sure that the saw blade does not rest on or touch any objects when the machine is switched on.

Switching on and off

Fig. A

To switch on the machine, press the on/off switch (3).

To switch the machine to continuous mode, • keep the on/off switch (3) pressed and simultaneously press the lock-on button (4).

To switch off the machine, release the on/off switch (3).

Sawing tips

Adjust saw blade and stroke rate to suit the material to be processed. For right radius curves it is best to use a narrow saw blade. Apply coolant or lubricant to deal with the fluttering produced along the cut line when sawing metal.

Check wood, chip boards, building materials • etc, for foreign bodies (nails, screws etc.), before sawing and remove them, if necessary. Clamp material well. Do not support the • workpiece with hand or foot. Do not touch objects or the floor with the saw running (danger of backlash).

Put the footplate on the surface of the • workpiece, and saw through it with constant contact pressure or feed. If the saw blade seizes switch the machine off immediately. Spread the gap with a suitable tool and pull out the saw blade.

After finishing work, switch off the machine • and only put down after it has come to a complete standstill.

Plunge cutting

Fig. C

Plunge cutting may only be used on soft materials such as wood, aerated concrete, gypsum plaster boards, etc.

However, this requires a certain practise and is only possible with short saw blades.

Place the saw onto the workpiece and switch • it on.

Ensure that the bottom edge of the footplate • rests on the workpiece surface as shown.

• Slowly saw into the workpiece at an angle, moving the saw to a vertical position and continue to saw along the cutting line.
• Switch the saw off and lift off the workpiece

when the work is complete.

Flush sawing

• Elastic bi-metal saw blades allow you to saw protruding objects (e,g, water pipes, iron bars, etc,) nearby the wall.
  Apply the saw blade directly to the wall and • bend slightly so that the footplate rests against the wall.
• Switch the machine on and saw off the workpiece keeping constant lateral pressure against the wall.

5. SERVICE & MAINTENANCE

Make sure that the machine is not live when carrying out maintenance work on the motor.

The machines have been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper machine care and regular cleaning.

Cleaning

Keep the ventilation slots of the machine clean to prevent overheating of the engine. Regularly clean the machine housing with a soft cloth, preferably after each use. Keep the ventilation slots free from dust and dirt. If the dirt does not come off use a soft cloth moistened with soapy water. Never use solvents such as petrol, alcohol, ammonia water, etc. These solvents may damage the plastic parts.

Lubrication

The machine requires no additional lubrication.

Faults

Should a fault occur, e.g. after wear of a part, please contact the service address on the warranty card. In the back of this manual you find an exploded view showing the parts that can be ordered.

Environment

To prevent damage during transport, the appliance is delivered in a solid packaging which consists largely of reusable material.

Therefore please make use of options for recycling the packaging.

Faulty and/or discarded electrical or electronic apparatus have to be collected at the appropriate recycling locations.

Warranty

The warranty conditions can be found on the separately enclosed warranty card.

SÄBELSÄGE

1. MACHINE-INFORMATIE

Technische specificaties

5. SERVICE OG VEDLIKEHOLD

The number of revolution of the machine can be electronically set.

DECLARATION OF CONFORMITY

(GB) We declare under our sole responsibility that this product is in conformity and accordance with the following standards and regulations:
(DE) Der Hersteller erklärt eigenverantwortlich, dass dieses Produkt den folgenden Standards und Vorschriften entspricht:
(NL) Wij verklaren onder onze volledige verantwoordelijk heid dat dit product voldoet aan, en in overeenstem ming is met, de volgende standaarden en reguleringen:
(FR) Nous déclarons sous notre seule responsabilité que ce produit est conforme aux standards et directives suivants:
(ES) Declaramos bajo nuestra exclusiva responsabilidad que este producto cumple con las siguientes normas y estándares de funcionamiento:
(PT) Declaramos por nossa total responsabilida-de que este produto está em conformidade e cumpre as normas e regulamentações que se seguem:
(IT) Dichiariamo, sotto la nostra responsabilità, che questo prodotto è conforme alle normative e ai regolamenti seguenti:
(SV) Vi garanterar på eget ansvar att denna produkt upp fyller och följer följande standarder och bestämmelser:
(FI) Vakuutamme yksinomaan omalla vastuullamme, että tämä tuote täyttää seuraavat standardit ja säädökset:
(NO) Vi erklærer under vårt eget ansvar at dette produktet er i samsvar med følgende standarder og regler:
(DA) Vi erklærer under eget ansvar, at dette produkt er i overensstemmelse med følgende standarder og bestemmelser:
(HU) Felelősségünk teljes tudatában kijelentjük, hogy ez a termék teljes mértékben megfelel az alábbi szabványoknak és előírásoknak:
(CS) Na naši vlastní zodpovědnost prohlašujeme, že je tento výrobek v souladu s následujícími standardy a normami:

(SK) Vyhlasujeme na našu výhradnú zodpovednosť, že tento výrobok je v zhode a súlade s nasledujúcimi normami a predpismi:
(SL) S polno odgovornostjo izjavljamo, da je ta izdelek v skladu in da odgovarja naslednjim standardom terpredpisom:
(PL) Deklarujemy na własną odpowiedzialność, że ten produkt spełnia wymogi zawarte w następujących normach i przepisach:
(LT) Prisiimdami visą atsakomybę deklaruojame, kad šis gaminys atitinka žemiau paminėtus standartus arba nuostatus:
(LV) Apgalvojam ar visu atbildību, ka šis produkts ir saskaņā un atbilst sekojošiem standartiem un nolikumiem:
(ET) Deklareerime meie ainuvastutusel, et see toode on vastavuses ja kooskõlas järgmiste standardite ja määrustega:
(RO) Declarăm prin aceasta cu răspunderea deplină că produsul acesta este în conformitate cu următoarele standarde sau directive:
(HR) Izjavljujemo pod vlastitom odgovornošu da je strojem ukladan sa slijedešim standardima ili standardiziranim dokumentima i u skladu sa odredbama:
(SR) Pod punom odgovornošću izjavljujemo da je usaglašen sa sledećim standardima ili normama:
(RU) Под свою ответственность заявляем, что данное изделие соответствует следующим стандартам и нормам:
(UK) На свою власну відповідальність заявляємо, що дане обладнання відповідає наступним стандартам і нормативам:
(EL) Δηλώνουμε υπεύθυνα ότι προϊόν αυτό συμφωνεί και τηρεί τους παρακάτω κανονισμο ύς και πρότυπα:
(BG) Ние заявяваме, по своя собствена отговорност, че този продукт отговаря на следните стандарти и директиви

EN 55014-1, EN 55014-2, EN 60745-1, EN 60745-2-11, EN 61000-3-2, EN 61000-3-3

2006/42/EC, 2002/95/EC, 2004/108/EC, 2002/96/EC, 2006/95/EC

Zwolle, 01-01-2010

J.A. Bakker-van logen

CEO Ferm BV

It is our policy to continuously improve our products and we therefore reserve the right to change the product specification without prior notice.

Ferm BV • Lingenstraat 6 • 8028 PM • Zwolle The Netherlands

Spare parts list

Position Description No.

1 till 12 Saw Blade Holder Complete 409916

31 Adjustable Footplate 409917

59 Switch 409920

Exploded view