Husqvarna-Electrolux

QFT60510W - Range hood Husqvarna-Electrolux - Free user manual and instructions

Find the device manual for free QFT60510W Husqvarna-Electrolux in PDF.

📄 28 pages English EN Download 💬 AI Question 10 questions ⚙️ Specs
Notice Husqvarna-Electrolux QFT60510W - page 22
View the manual : Dansk DA English EN Suomi FI Norsk NO Svenska SV
Pick your language and provide your email: we'll send you a specifically translated version.
Product Type Range hood
Brand Husqvarna-Electrolux
Model QFT60510W
Width 60 cm
Depth 50 cm
Power Supply 220-240 V, 50 Hz
Number of Suction Speeds 4 (speeds 1-4, with timed boost on speeds 3 and 4)
Breeze Function Yes (low speed for 1 hour, then auto-off)
Lighting LED (replaceable by service only)
Grease Filter Washable in dishwasher or by hand; clean monthly
Charcoal Filter (Recirculation Mode) Type 20 LONG LIFE (washable) or Type 15 (non-washable, replace every 4 months)
Wireless Hob Connection Yes (Hob²Hood, automatic speed adjustment)
Minimum Installation Height (Electric Hob) 50 cm
Minimum Installation Height (Gas Hob) 65 cm
Filter Saturation Indicator Yes (grease filter 'F', charcoal filter 'C')
Temperature Alarm Yes (activates speed 3 if temperature too high)
Control Type Electronic push buttons with display
Energy Efficiency Class Not specified in manual
Noise Level Not specified in manual
Suction Capacity Not specified in manual
Accessories & Spare Parts Original spare parts available at www.husqvarna-electrolux.se/shop
Safety Features Thermal cut-out, no open flames near hood, mandatory grating

Frequently Asked Questions - QFT60510W Husqvarna-Electrolux

How often should I clean the grease filter?
Clean the grease filter at least once a month. It can be washed by hand with non-aggressive detergents or in a dishwasher at a low temperature and short cycle.
How do I wash the charcoal filter (Type 20 LONG LIFE)?
Wash the charcoal filter every two months in hot water with detergent, or in a dishwasher at 65°C. Remove excess water, then dry the inner mattress in an oven at 100°C for 10 minutes.
When should I replace the charcoal filter?
For the washable Type 20 LONG LIFE filter, replace the inner mattress every 3 years or when damaged. For non-washable Type 15 filters, replace the cartridge at least every 4 months.
How do I reset the filter saturation indicator?
Switch on the hood, then press and hold button 1 (ON/OFF) for about 3 seconds. If both 'F' and 'C' flash, reset twice (once for each filter).
How do I activate the charcoal filter saturation indicator?
Turn off the hood, then simultaneously press buttons 2 and 3 for 3 seconds. The display will show 'F' and 'C' flashing for 2 seconds to confirm activation.
What is the Hob²Hood function?
The hood can wirelessly connect to a compatible cooktop to automatically adjust the suction speed. Refer to the cooktop manual for compatibility. After a power outage, wait 1 minute for reconnection.
What is the minimum installation height?
The minimum distance between the hob and the lowest part of the hood is 50 cm for electric cookers and 65 cm for gas or mixed cookers. Follow the gas hob installation manual if a greater distance is specified.
What does the temperature alarm do?
If the temperature near the display becomes too high, the hood automatically activates speed 3 and the display shows a flashing 't'. It returns to normal when the temperature drops. You can manually exit by pressing key 2.
Can I replace the LED lamp myself?
No, the LED lighting should only be replaced by qualified service personnel. Contact the technical service for replacement.
What safety measures should I observe?
Never use the hood without the grating installed, do not flambé under the hood, ensure adequate ventilation when used with gas appliances, and disconnect the power before maintenance. The hood is not intended for use by children without supervision.

User questions about QFT60510W Husqvarna-Electrolux

0 question about this device. Answer the ones you know or ask your own.

Ask a new question about this device

The email remains private: it is only used to notify you if someone responds to your question.

No questions yet. Be the first to ask one.

Download the instructions for your Range hood in PDF format for free! Find your manual QFT60510W - Husqvarna-Electrolux and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. QFT60510W by Husqvarna-Electrolux.

USER MANUAL QFT60510W Husqvarna-Electrolux

BÄSTA KUND FÖR PERFEKT RESULTAT

4.2 Kolfilter - Type 20 LONG LIFE - Aktivt kolfilter som kan rengöras

4.2 Type 20 LONG LIFE - Vaskbart aktivt kullfilter

Thank you for choosing this Husqvarna-Electrolux product. We have created it to give you impeccable performance for many years, with innovative technologies that help make life simpler – features you might not find on ordinary appliances. Please spend a few minutes reading to get the very best from it.

Visit our website to:

Husqvarna-Electrolux QFT60510W - Visit our website to: - 1

Get usage advice, brochures, trouble shooter, service information: www.husqvarna-electrolux.se

Husqvarna-Electrolux QFT60510W - Visit our website to: - 2

Register your product for better service: www.husqvarna-electrolux.se

Husqvarna-Electrolux QFT60510W - Visit our website to: - 3

Buy Accessories, Consumables and Original spare parts for your appliance: www.husqvarna-electrolux.se/shop

ENVIRONMENT CONCERNS

Recycle the materials with the symbol: Put the packaging in applicable containers to recycle it. Help protect the environment and human health and to recycle waste of

electrical and electronic appliances. Do not dispose appliances marked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office.

Husqvarna-Electrolux QFT60510W - ENVIRONMENT CONCERNS - 1

CUSTOMER CARE AND SERVICE

We recommend the use of original spare parts.

When contacting Service, ensure that you have the following data available.

The information can be found on the rating plate. Model, PNC, Serial Number.

Husqvarna-Electrolux QFT60510W - CUSTOMER CARE AND SERVICE - 1

Warning / Caution-Safety information.

Husqvarna-Electrolux QFT60510W - CUSTOMER CARE AND SERVICE - 2

General information and tips

Husqvarna-Electrolux QFT60510W - CUSTOMER CARE AND SERVICE - 3

Environmental information.

Subject to change without notice.

Husqvarna-Electrolux QFT60510W - CUSTOMER CARE AND SERVICE - 4

SAFETY INSTRUCTIONS

Caution! Closely follow the instructions set out in this manual. All responsibility, for any eventual inconveniences, damages or fires caused by not complying with the instructions in this manual, is declined. The extractor hood has been designed exclusively for domestic use.

Caution! Do not connect the appliance to the mains until the installation is fully complete. Before any cleaning or maintenance operation, disconnect hood from the mains by removing the plug or disconnecting the mains electrical supply.

Always wear work gloves during the maintenance, installation and lighting operations. The appliance is not intended for use by children or persons with impaired physical, sensorial or mental faculties, or if lacking in experience or knowledge, unless they are under supervision or have been trained in the use of the appliance by a person responsible for their safety. This appliance is designed to be operated by adults, children should be monitored to ensure that they do not play with the appliance. This appliance is designed to be operated by adults. Children should not be allowed to tamper with the controls or play with the appliance. Never use the hood without effectively mounted grating! The hood must NEVER be used as a support surface unless specifically indicated. The premises where the appliance is stalled must be sufficiently ventilated, when the kitchen hood is used together with other gas combustion devices or other fuels. The ducting system for this appliance must not be connected to any existing ventilation system which is being used for any other purpose such as discharging exhaust fumes from appliances burning gas or other fuels. The flaming of foods beneath the hood itself is severely prohibited. The use of exposed flames is detrimental to the filters and may cause a fire risk, and must therefore be avoided in all circumstances. Any frying must be done with care in order to make sure that the oil does not overheat and ignite.

Caution! Accessible parts of the hood may become hot when used with cooking appliance.

With regards to the technical and safety measures to be adopted for fume discharging it is important to closely follow the regulations provided by the local authorities. The hood must be regularly cleaned on both the inside and outside (AT LEAST ONCE A MONTH).

This must be completed in accordance with the maintenance instructions provided in this manual). Failure to follow the instructions provided in this user guide regarding the cleaning of the hood and filters will lead to the risk of fires. Do not use or leave the hood without the lamp correctly mounted due to the possible risk of electric shocks. We will not accept any responsibility for any faults, damage or fires caused to the appliance as a result of the non-observance of the instructions included in this manual.

Warning! Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards.

2. USE

The hood serves to aspirate the fumes and vapors resulting from cooking.

The attached installation manual indicates the version to be used depending on the model you have, the suction version with

external evacuation of filtering with

internal recirculation

3. INSTALLATION

The mains power supply must correspond to the rating indicated on the plate situated inside the hood. If provided with a plug connect the hood to a socket in compliance with current regulations and positioned in an accessible area, after installation. If it not fitted with a plug (direct mains connection) or if the plug is not located in an accessible area, after installation, apply a double pole switch in accordance with standards which assures the complete disconnection of the mains under conditions relating to over-current category III in accordance with installation instructions.

⚠ Warning! Before re-connecting the hood circuit to the mains supply and checking the efficient function, always check that the mains cable is correctly assembled.

The minimum distance between the supporting surface for the cooking equipment on the hob and the lowest part of the range hood must be not less than 50cm from electric cookers and 65cm from gas or mixed cookers. If the instructions for installation for the gas hob specify a greater distance, this must be adhered to.

3.1 Hob 2 Hood

The hood is equipped with a function for wireless connection with the cooktop for automatic adjustment of the most suitable speed. Refer to the instruction manual of the cooktop to verify the presence and compatibility of this function.

In the case of first connection to the mains or abrupt disconnection from power supply (blackout), wait 1 minute to allow the hood to restore the connection with the cooktop.

4. MAINTENANCE

Husqvarna-Electrolux QFT60510W - MAINTENANCE - 1

ATTENTION! Before performing any maintenance operation, isolate the hood from the electrical supply by switching off at the connector and removing the connector fuse.

Or if the appliance has been connected through a plug and socket, then the plug must be removed from the socket. The cooker hood should be cleaned regularly (at least with the same frequency with which you carry out maintenance of the fat filters) internally and externally. Clean using the cloth dampened with neutral liquid detergent. Do not use abrasive products. DO NOT USE ALCOHOL!

Husqvarna-Electrolux QFT60510W - MAINTENANCE - 2

Warning! Failure to carry out the basic cleaning recommendations of the cooker hood and replacement of the filters may cause fire risks. Therefore, we recommend observing these instructions.

The manufacturer declines all responsibility for any damage to the motor or any fire damage linked to inappropriate maintenance or failure to observe the above safety recommendations.

4.1 Grease filter - The grease filter must be cleaned once a month using non aggressive detergents, either by hand or in the dishwasher, which must be set to a low temperature and a short cycle. When washed in a dishwasher, the grease filter may discolour slightly, but this does not affect its filtering capacity.

Line drawing of a hand holding a small object (no text or symbols)

4.2 Charcoal filter - Type 20 LONG LIFE - Washable activated charcoal fi Iter

The charcoal filter can be washed once every two months using hot water and a suitable detergent, or in a dishwasher at 65° C (if the dishwasher is used, select the full cycle function and leave dishes out).

Eliminate excess water without damaging the filter, then remove the mattress located inside the plastic frame and put it in the oven for 10 minutes at 100° C to dry completely. Replace the mattress every 3 years and when the cloth is damaged.

Type 15 - NON-washable activated charcoal filter

The saturation of the charcoal filter occurs after more or less prolonged use, depending on the type of cooking and the regularity of cleaning of the grease filter. In any case it is necessary to replace the cartridge at least every four mounths. The charcoal filter may NOT be washed or regenerated.

(1*) (2*) (3**)

5. CONTROLS

The hood is fitted with a control panel with aspiration speed selection control and a light switch to control cooking area lights. Use the high suction speed in cases of concentrated kitchen vapours. It is recommended that the cooker hood suction is switched on for 5 minutes prior to cooking and to leave in operation during cooking and for another 15 minutes approximately after terminating cooking.

The control switches are located on the unit's front panel:

12 ① - + 8 * dB

1 Suction speed (power) ON/OFF/decrease key

2 Suction speed (power) 1 - 2 - 3 -4 increase key. . Suction speeds (powers) 3 and 4 have a limited duration, respectively 10 and 5 minutes, after which suction speed (power) 2 is activated.

Note: The LED on the display flashes indicating speed timing.

3 Lighting ON/OFF key

4 "Breeze" function key (Environment ventilation)

The hood switches on at low suction speed (power) for about one hour and then switches off.

5 Display

Filter saturation indicator

At regular intervals, the hood warns when the filters must be serviced.

Grease filter saturation indicator

The set speed and the letter "F" alternate on the display.

Carbon filter saturation indicator

The set speed and the letter "C" alternate on the display.

Reset of saturation indicator

In order to reset the saturation indicator, switch on the hood then press and hold button 1 for about 3 seconds.

Perform filter maintenance as

recommended in this manual.

In the event that both indicators of filter saturation “F” and “C” start flashing, proceed with the reset twice.

The saturation indicator of the charcoal filter is not normally active and if the hood is used in the recirculation mode, it must be activated manually the first time.

Activation of the charcoal filter saturation indicator:

Turn off the hood and simultaneously press buttons 2 and 3 for 3 seconds.

The letters “F” and “C” will flash on the display for 2 seconds, to indicate successful activation of the saturation indicator of the charcoal filter.

Deactivation of the charcoal filter saturation indicator:

Turn off the hood and simultaneously press the buttons 2 and 3 for 3 seconds. Only letter "F" will flash on the display for 2 seconds, to indicate successful deactivation of the saturation indicator of the charcoal filter.

Temperature Alarm

The hood is equipped with a temperature sensor which activates the motor at speed 3 in case the temperature in the display zone is too high.

The alarm condition is indicated by the display with the letter "t" flashing.

This condition remains as such until the temperature falls below the alarm threshold.

This mode can be quit by pressing key "2".

Every 30" the sensor checks the ambient temperature of the display zone.

5.1 Hob 2 Hood

The hood is equipped with a function for wireless connection with the cooktop for automatic adjustment of the most suitable speed. Refer to the instruction manual of the cooktop to verify the presence and compatibility of this function.

In the case of first connection to the mains or abrupt disconnection from power supply (blackout), wait 1 minute to allow the hood to restore the connection with the cooktop.

6. LIGHTING

The hood is equipped with a lighting system based on LED technology.

The LEDs guarantee an optimum lighting, a duration up to 10 times as long as the traditional lamps and allow to save 90% electrical energy.

Husqvarna-Electrolux QFT60510W - LIGHTING - 1

Caution! Do not look directly into the LED light.

For replacement, contact the technical service.

www.husqvarna-electrolux.se/shop

Husqvarna-Electrolux QFT60510W - LIGHTING - 2

Husqvarna-Electrolux QFT60510W - LIGHTING - 3

Husqvarna-Electrolux QFT60510W - LIGHTING - 4

Husqvarna-Electrolux QFT60510W - LIGHTING - 5

Husqvarna-Electrolux QFT60510W - LIGHTING - 6

CE

Manual assistant
Powered by Anthropic
Waiting for your message
Product information

Brand : Husqvarna-Electrolux

Model : QFT60510W

Category : Range hood