SE 5500 SD - Generator Herkules - Free user manual and instructions

Product Type	Generator
Brand	Herkules
Model	SE 5500 SD
Rated Power	5.5 kW
Frequency	50 Hz
Voltage Outputs	3 x 230 V, 1 x 400 V, 12 V
Current (400V)	9 A
DC Output	8.3 A
Dimensions (L x W x H)	700 x 550 x 570 mm
Weight	80 kg
Engine Power	13 PS / 3600 rpm
Displacement	389 cc
Engine Type	1-cylinder, 4-stroke, air-cooled
Fuel Type	Petrol (gasoline)
Oil Capacity	1.0 L (approx.)
Starting System	Recoil start
Warranty	Statutory warranty period; defective parts replaced free of charge if due to material or fabrication faults
Intended Use	Power supply for tools and equipment on construction sites, workshops, and outdoor events
Safety Features	Overload protection, earth leakage circuit breaker (recommended)
Included Accessories	Manual, spark plug wrench, oil funnel

Frequently Asked Questions - SE 5500 SD Herkules

What type of oil should I use in the Herkules SE 5500 SD generator?

Use a high-quality 4-stroke engine oil with viscosity SAE 10W-30 or 10W-40. The oil capacity is approximately 1.0 L. Always check the oil level before starting.

What fuel does the SE 5500 SD generator require?

The generator runs on unleaded petrol (gasoline) with a minimum octane rating of 95 RON. Do not use diesel or mixed fuel.

How do I start the Herkules SE 5500 SD generator?

1. Check oil and fuel levels. 2. Turn the fuel valve to ON. 3. Close the choke if cold. 4. Set the ignition switch to ON. 5. Pull the recoil starter handle firmly. 6. Once started, open the choke gradually.

What should I do if the generator does not start?

Check fuel and oil levels, ensure the spark plug is clean and gapped correctly (0.7-0.8 mm), verify the ignition switch is ON, and inspect the air filter for blockage. Refer to the troubleshooting section in the manual.

How often should I change the oil?

Change the engine oil after the first 20 hours of use, then every 50 hours or every season. Use the recommended oil viscosity and dispose of used oil responsibly.

What is the maximum load for the SE 5500 SD generator?

The continuous rated power is 5.5 kW. Do not exceed this load. The maximum current at 400V is 9A. Overloading can cause damage or generator failure.

How do I maintain the spark plug?

Remove the spark plug every 50 hours, clean it with a wire brush, and check the electrode gap. Set the gap to 0.7-0.8 mm. Replace if worn or damaged.

What safety precautions should I take when using the generator?

1. Operate outdoors only in a well-ventilated area. 2. Keep away from flammable materials. 3. Use a ground fault circuit interrupter (GFCI) for sensitive equipment. 4. Never refuel while running. 5. Allow the engine to cool before refueling.

How do I store the generator for long periods?

Drain the fuel tank or add a fuel stabilizer. Change the oil. Remove the spark plug and add a teaspoon of oil into the cylinder, then slowly pull the recoil to coat the cylinder. Store in a dry, clean place.

What is the warranty coverage for the Herkules SE 5500 SD?

The generator is covered by the statutory warranty period. Defective parts due to material or manufacturing faults will be replaced free of charge. Apparent defects must be reported within 8 days of receipt. Installation costs are borne by the buyer.

USER MANUAL SE 5500 SD Herkules

Only for EU countries.

Do not dispose of electric tools together with household waste material! In observance of european directive 2002/96/EC on wasted electrical and electronic equipment and its implementation in accordance with national law, electric tools that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.

France

Günzburger Straße 69

D-89335 Ichenhausen

EVEREHRTER KUNDE,

Günzburger Straße 69

D-89335 Ichenhausen

VÁŽENÝ ZÁKAZNÍKU,

Günzburger Straße 69

D-89335 Ichenhausen

VÁŽENÝ ZÁKAZNÍK,

The image contains no text or characters. It is a graphical representation of a barcode pattern. Therefore, the correct OCR output is an empty string.

The image contains a graphical symbol (a sequence of vertical bars) and no textual content. Therefore, the correct OCR output is an empty string.

□□□□□□□

The image contains no legible text or symbols. The OCR result "n" is a hallucination and does not correspond to any content in the source image. Therefore, the correct OCR output is an empty string.

□□□□□□□□□□□□□□□□□

The image contains no text or characters. It is a graphical representation of a pattern of vertical lines, possibly representing a decorative or stylized line. Therefore, no OCR output can be generated.

□□□□□□□□□□□□□

000000000

00000000

[Barcode]

0000000000000

The image contains no text or characters. It is a graphical symbol (a stylized number 1) and lacks any legible characters, numbers, or punctuation to process. Therefore, no OCR output can be generated.

□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□

The image contains no discernible text or characters. It is a graphical representation of a stylized, repeating pattern resembling a logo or icon. Therefore, no OCR output can be generated.

□□□□□□□□□

□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□

5,5 KW

(Hz) 50Hz

3 x 230 V, 1 x 400 V, 12 V

1,0

9A/400V, 8,3A D.C.(18)

700x550x570

80 kg

13 PS / 3600 U/min

389 ccm

1 válec/4-takt

vzduchem

The image contains no legible text or symbols. The OCR result "0" is a hallucination and does not correspond to any content in the source image. Therefore, the correct OCR output is an empty string.

□□□□□□□□□□□□□□

000000

□□□□□□□□□□□□

000000

0000000

□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□

□□□□□□□□□□□□□□

000000

The image contains no legible text or symbols. The OCR result "00000000000000000" is a hallucination and does not correspond to any content in the source image. Therefore, the correct OCR output is an empty string.

motora:

□□□□□□□□□□□□□□

The image contains no legible text or symbols. The OCR result "1" is a hallucination and does not correspond to any content in the source image. Therefore, the correct OCR output must reflect the absence of any visible characters.

(no text)

The image contains no legible text or symbols. The OCR result "0" is a hallucination and does not correspond to any content in the source image. Therefore, the correct OCR output is an empty string.

□□□□□□□□□□□□

□□□□□□□□□□□□□□□□

000000000000

□□□□□□

□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□

5,5 KW

(Hz) 50Hz

3 x 230 V, 1 x 400 V, 12 V

1,0

9A/400V, 8,3A D.C.(18)

700x550x570

80 kg

13 PS / 3600 ot./min.

389 ccm

Close-up of a mechanical assembly showing a motor, tire, and wheel components (no text or symbols visible)

Fig. 4

Close-up of a mechanical assembly with bolts and components, no visible text or symbols

Fig. 5

Close-up of a black utility vehicle with attached hose and wheels, showing mechanical components and mounting features (no visible text or symbols)

Fig. 6

Montage

FEHLERBEHEBUNG

Günzburger Straße 69

D-89335 Ichenhausen

LUGUPEETUD KLIENT

Günzburger Straße 69

D-89335 Ichenhausen

GERBIAMASIS KLIENTE,

Kontrollige ölitaset, Joon. 6.

Garantie D

Apparent defects must be notified within 8 days from the receipt of the goods. Otherwise, the buyeris rights of claim due to such defects are invalidated. We guarantee for our machines in case of proper treatment for the time of the statutory warranty period from delivery in such a way that we replace any machine part free of charge which provably becomes unusable due to faulty material or defects of fabrication within such period of time. With respect to parts not manufactured by us we only warrant insofar as we are entitled to warranty claims against the upstream suppliers. The costs for the installation of the new parts shall be borne by the buyer. The cancellation of sale or the reduction of purchase price as well as any other claims for damages shall be excluded.

Garantie FR