FZR 4210-B - Lawn mower Fieldmann - Free user manual and instructions

Product Type	Petrol Lawn Mower
Engine	RATO RV125-S, 4-stroke OHV, air-cooled
Engine Displacement	127 cm³
Rated Power	1.9 kW
Engine Speed	2900 rpm
Starting System	Pull Cord
Fuel Type	Unleaded petrol, min. 95 octane
Fuel Tank Capacity	1.0 L
Oil Capacity	0.5 L (SAE30 or 15W-40)
Cutting Width	420 mm
Cutting Height Range	25–75 mm (6 positions, central adjustment)
Grass Catcher Capacity	45 L
Wheel Size (Front/Rear)	150 mm / 200 mm
Chassis Material	Steel
Mowing Modes	Collection, Rear Discharge, Mulching
Noise Level	96 dB(A)
Weight	21.7 kg
Handle	Folding, height-adjustable
Safety Features	Start/brake lever, engine stop when released; spark plug disconnect for maintenance
Warranty	24 months

Frequently Asked Questions - FZR 4210-B Fieldmann

How do I assemble the handle and grass catcher?

Insert the lower handle into the mower holes and secure with screws and nuts. Attach the upper handle to the lower handle using quick couplers and wing nuts. For the grass catcher, hook the plastic clips onto the steel frame. Ensure cables are not pinched.

What oil and fuel should I use?

Use SAE30 or 15W-40 motor oil (approx. 600 ml). Fill to between MIN and MAX marks on dipstick. Use unleaded petrol with at least 95 octane. Do not use ethanol or methanol blends.

How do I start the lawn mower?

Press the fuel primer bulb 2-3 times if cold. Pull the start/brake lever toward the handle and hold. Pull the starter cord sharply. Engine usually starts after 3-4 pulls. Release the lever to stop.

How do I adjust the cutting height?

Use the central mowing height adjustment lever (item 10) to select one of 6 positions ranging from 25 to 75 mm. For most lawns, use the middle setting. Never cut more than 1/3 of grass length at once.

What should I do if the engine won't start?

Check fuel level, spark plug connection, air filter, and choke position. Ensure the spark plug gap is 0.7-0.8 mm. If still not starting, consult the troubleshooting section or contact service.

How often should I change the oil?

Change oil after first 5 hours of operation, then every 25 hours or every 6 months. Always check oil level before each use.

Can I use this mower on slopes?

Yes, but only on slopes with inclination up to 20°. Mow across the slope (perpendicular), never up and down. Use caution to prevent engine seizure.

What does the grass catcher full indicator look like?

The grass catcher has a plastic flap at the rear. When the catcher is empty or not full, the flap is raised. When it closes, the catcher is full and needs emptying.

How do I switch to mulching mode?

Remove the grass catcher. Hold the grass catcher cover open and insert the mulching plug into the discharge chute until it clicks. Ensure engine is off before attaching or removing the plug.

What safety precautions should I take before maintenance?

Always turn off the engine and disconnect the spark plug before any maintenance. Wait for the blade to stop rotating. Wear gloves when handling blades.

USER MANUAL FZR 4210-B Fieldmann

Abstract black and white spiral pattern with no text or symbols

FIELDMANN®

Home & Garden Performance

Black and silver PRDMAN lawn mower with visible blades and mounting bracket (no text or symbols)

FZR 4210 B

English 3-20

Čeština....21 - 38

Slovenština....39 - 56

Magyarul....57 - 74

Polski 75-98

Petrol Lawnmower USER'S MANUAL

Thank you for purchasing this rotary petrol lawnmower. Before you start using it, please, carefully read this user's manual and save it for possible future use.

TABLE OF CONTENTS

1. GENERAL SAFETY INSTRUCTIONS 4
   Important safety notice....4
   Packaging 4
   User's Manual....4
2. EXPLANATION OF INSTRUCTION LABELS ON THE MACHINE....5
3. DESCRIPTION OF THE LAWNMOWER....7
4. ASSEMBLY/PREPARATION....7
   Taking the lawnmower out of the cardboard packaging ....7
5. ASSEMBLING THE LAWNMOWER....8
6. BEFORE STARTING THE LAWNMOWER 9
   Adding oil....9
   Adding fuel....10
7. CONTROLLING AND OPERATING THE LAWNMOWER.... 10
   Starting the lawnmower 10
   Controlling travel....11
   Application range for the lawnmower....11
   Mowing with the grass catcher 11
   Mowing with rear discharge 11
   Mulching....12
   Setting the mowing height....12
   Replacing the mowing blades 12
   Changing the motor oil 13
8. SAFETY INSTRUCTIONS....13
   General safety instructions 13
   Instructions for use 14
9. MAINTENANCE....15
   Lawn care....15
   Maintenance 15
   Warranty does not cover....16
   Storage 16
10. TECHNICAL SPECIFICATIONS 17
11. REGULAR MAINTENANCE SCHEDULE.... 18
12. DETECTION AND TROUBLESHOOTING 19
13. DISPOSAL....20

1. GENERAL SAFETY INSTRUCTIONS

IMPORTANT SAFETY NOTICE

* Carefully unpack the product and take care not to throw away any part of the packaging before you find all the parts of the product.
Store the machine in a dry place out of reach of children.
Read all warnings and instructions. Not following warnings or instructions may lead to injury by electrical shock, a fire and/or serious injuries.

PACKAGING

The product is packed in a package that prevents damage during transport. This package is a resource and so can be handed over for recycling.

USER'S MANUAL

Before you start working with the machine, read the following safety and usage instructions.

Acquaint yourself with the operating elements and the correct use of the machine. Keep the user's manual in a safe place where it can be easily retrieved for future use. Save the original packaging, including the internal packing material, warranty card and proof of purchase receipt at least for the duration of the warranty.

If you need to ship this machine, pack it in the original cardboard box to ensure maximum protection during shipping or transport (e.g. when moving or when you need to send this product for repair).

Note: If you hand over the machine to somebody else, do so together with the user's manual. Following the instructions in the included user's manual is a prerequisite for the proper use of the machine.

The user's manual also contains operating, maintenance and repair instructions.

The manufacturer takes no responsibility for accidents or damages resulting from not following the instructions in this manual.

2. EXPLANATION OF INSTRUCTION LABELS ON THE MACHINE

Before putting into operation, please carefully read the user's manual.

Keep other persons away from the work area.

Attention, rotating blades! Protect yourself against the danger of injury to limbs.

Emission of toxic gasses. Do not use the petrol lawnmower in enclosed or unventilated areas.

Hot surfaces, risk of burns!

Before carrying out maintenance, turn off the engine and disconnect the spark plug.

Never add fuel while the engine is running.

Indicates that there is a risk of injury to persons, death or damage to the machine if instructions are not followed.

Use hearing protection. Use eye protection. Use breathing organ protection.

Always maintain a distance from moving parts.

Travel along the slope on contours, not up and down.

Conforms to all relevant European directives.

Petrol is extremely fl ammable and therefore allow the engine to cool down for 2 minutes before adding more fuel.

3. DESCRIPTION OF THE

1. Travel lever
2. Start / brake lever
3. Top part of the handle
4. Screws with wing nuts
5. Bottom part of the handle
6. Air filter cover
7. Fuel primer bulb – Primer
8. Front handle
9. Cap with oil dipstick
10. Mowing height adjustment lever
11. Grass catcher
12. Grass catcher cover

4. ASSEMBLY/PREPARAT

Before assembling and starting the petrol lawnmower, first carefully read the entire user's manual and the instructions contained in it.

IMPORTANT INFORMATION: The lawnmower is supplied WITHOUT FUEL AND OIL in the engine. Your new lawnmower was tested at the production plant meaning that a small amount of residual oil may be in the engine.

TAKING THE LAWNMOWER OUT OF THE CARDBOARD PACKAGING

Take the lawnmower out of the cardboard packaging and check that no loose parts are left in the packaging.

5. ASSEMBLING THE LAWNMOWER

IMPORTANT INFORMATION: Carefully unfold the lawnmower handle, being careful not to pinch or damage the lawnmower's control cables.

1. ASSEMBLING THE HANDLE

1. Insert the bottom part of the handle (Fig. 2a) into the respective holes on the lawnmower (see arrow) and secure in place with screw and nut.
2. Attach the top part of the handle (Fig. 1 – point 3) to the bottom part of the handle (Fig.1 – point 5) using the included screws with the quick coupler and wing nuts (Fig.2b).

Close-up of a black tool with a white handle attachment, labeled Fig. 2b (no text or symbols on the tool itself)

2. ASSEMBLING THE GRASS CATCHER

Secure the plastic hooks at the end of the textile part of the grass catcher into the steel frame (fi g. 4).

Two black plastic containers with a curved arrow indicating a change or motion, labeled 'Fig. 4' (no text on the containers themselves)

IMPORTANT NOTICE: The grass catcher is equipped with a full indicator. It is a plastic flap at the rear of the grass catcher. When the grass catcher is not full, the flap is raised. When it closes, it is necessary to tip out the grass catcher.

6. BEFORE STARTING THE LAWNMOWER

ADDING OIL

The lawnmower is supplied without motor oil. Before first start up, add motor oil SAE30 or 15W-40 (approx 600 ml) according to the following instructions.

1. When pouring in the oil, place the lawnmower on a level surface.
2. Pull the cap with the oil dipstick out of the oil refi ll hole (Fig. 5).
3. After adding oil, put the dipstick back into the hole and tighten it.
4. The oil level must be between the upper (MAX) and lower (MIN) limit (Fig. 5).

Caution! DO NOT OVERFILL the oil tank, otherwise a large amount of smoke will come out of the exhaust when the lawnmower is started up.
IMPORTANT INFORMATION: Check the oil level before every use of the lawnmower. Add oil if necessary. Add oil up to the MAX level mark on the oil dipstick.
IMPORTANT INFORMATION: Replace the oil after the first 5 hours of operation and subsequently after every 25 hours of operation.

ADDING FUEL

The suitable type of fuel for this engine is NATURAL 95

After unscrewing the fuel tank cap, add the fuel, pouring it in all the way up to the collar of the fuel tank but do not overfi ll it.

Always add fresh, clean and approved lead-free petrol with an octane rating of at least 95.

Caution! In the event that you spill any oil or fuel on the lawnmower when refilling, wipe it away immediately. Do not store or add fuel or handle it in any way in the vicinity of an open fi re.

Caution! Fuels mixed with alcohol or fuels with ethanol or methane additives may bind moisture to themselves, which may result in separation during storage and the formation of acids. Subsequently during storage the acid vapours may damage the fuel system of the lawnmower engine. These fuels must not be used in the lawnmower.

IMPORTANT INFORMATION: When not using the lawnmower for longer than 30 days, drain the fuel tank, start the engine and let it run until the fuel lines and the carburettor are empty (the engine will stop on its own). This will prevent future engine problems. Before using it again, add fresh fuel into the fuel tank.

7. CONTROLLING AND OPERATING THE LAWNMOWER

STARTING THE LAWNMOWER

1. If the engine is not warmed up, press the fuel primer bulb 2-3 times (Fig. 6 – point 1).
   If the engine is already warm, it is not necessary to use the fuel primer bulb.
2. Pull the start/brake lever towards the handle and hold it there (Fig. 6 – point 2), then pull on the pull cord (Fig. 6 – point 3). The engine should start up after 3-4 pulls.
3. The engine is turned off by releasing the start/brake lever.

Fig. 6

Illustration of a person performing a rope knotting technique (no text or symbols)

Illustration of a hand holding a tool with an arrow indicating motion, no text or symbols present

Caution! A small amount of smoke may be emitted when the engine is started up for the first time as the protective layers in the engine are burnt off. This is completely normal and does not constitute a problem.

CONTROLLING TRAVEL

The travel is controlled using the travel lever (Fig. 7 – point 1). When the lever is pulled to the handle, the lawnmower will start moving.

To stop, release the lever. This lawnmower has one constant speed.

Illustration of two hands holding a cable with a clip, showing a motion sequence (no text or symbols)

APPLICATION RANGE FOR THE LAWNMOWER

Mowing with collection of grass clippings in a grass catcher

Mowing with rear discharge of grass clippings

Mulching - mowing with loose placement of grass clippings on the lawn

Caution! Do not use the mower on slopes with an inclination of more than 20^ , otherwise motor seizure might occur!

MOWING WITH THE GRASS CATCHER

When the grass catcher is installed, grass clippings are discharged into the grass catcher.

Caution! In case of poor mown grass catching, increase the mowing height and check if the lawn is wet.

MOWING WITH REAR DISCHARGE

Without the grass catcher installed, the grass catcher cover serves as a deflector that directs the movement of the grass clippings towards the ground. A row of grass clippings is thereby formed behind the lawnmower.

MULCHING

Caution! Attach and remove the mulching plug only with the engine turned off.
Caution! Use only original mulching accessories when mulching.

1. Remove the grass catcher and hold the plastic grass catcher cover with your hand (Fig. 9 – point 1).
2. Install the mulching plug into the discharge chute (Fig. 9 – point 2) and make sure that the plug is seated firmly.
   IMPORTANT INFORMATION: Do not mulch tall grass all at once, this will prevent overloading the lawnmower mechanism and the engine.

Fig. 9

SETTING THE MOWING HEIGHT

The mowing height is set centrally using the central mowing height adjustment lever (Fig. 1 – point 10). You can select in the range of 25 to – 75 mm. The middle mowing height is the most suitable for the majority of lawns. Lawn damage may result when the lowest height is set.

Caution! For maximum effectiveness, please always trim the grass by 1/3 of its length only.

Mow the overgrown grass gradually and after each mowing, lower the height by one step.

To keep quality lawn, do not use the lowest mowing height setting.

REPLACING THE MOWING BLADES

Caution! For this task, we recommend that you contact an authorised service centre.

If you wish to replace the mowing blade, remove the bolt (Fig. 10). Perform the installation according to the provided picture. Tighten the screw. The tightening torque is 40 Nm . When replacing the blade, replace the fastening bolt also.

Technical line drawing of a mechanical bracket assembly with mounting holes and a bolted base (no text or symbols)

CHANGING THE MOTOR OIL

Caution! For this task, we recommend that you contact an authorised service centre.

The drain plug is located under the engine (Fig. 11 – point 1). Place a suitable container for catching the used oil under the engine and remove the plug. Tilt the lawnmower so that all the oil can drain from the oil tank.

Fig. 11

Technical line drawing of a mechanical assembly with labeled components (no readable text or symbols)

After draining the oil, put the plug back into the hole, making sure that the plug is securely in its place and wipe away any drops of spilled oil.

Add type SAE30 or 15W-40 oil into the oil tank.

When the oil dipstick is inserted into the hole and screwed in, the oil level should be between the Min and Max marks (Fig. 11). Do not overfill the oil tank.

Start the engine and allow it to run for a short time. Stop the engine, wait 1 minute and remeasure the oil level in the oil tank. Add oil to the required level if necessary.

8. SAFETY INSTRUCTIONS

GENERAL SAFETY INSTRUCTIONS

This product is used exclusively for mowing grass. Do not use it for any other purposes than those intended. Otherwise there is a risk of damaging it or an injury.
* Never allow children or persons who are not acquainted with the contents of this user's manual to work with the machine.
The person operating the lawnmower is responsible for the safety of persons in the work area.

Never operate the lawnmower in the near vicinity of other people, children or freely roaming animals.

Before starting mowing, check the terrain where the lawnmower will be used and remove stones, wires, sticks, splinters, bones and other foreign objects, which could become caught in it or deflected or cause injuries.

INSTRUCTIONS FOR USE

All nuts, pins and bolts must be properly tightened so that the machine is in a safe and operational condition.
Never use the lawnmower without the grass catcher or protective cover.
* Never use the lawnmower with loose mowing blades. Always check in advance that all respective bolts are securely tightened. Blunt blades must be sharpened evenly.

Damaged blades must be replaced.

When working with the lawnmower, wear long pants and solid footwear.
Never start the lawnmower in enclosed or poorly ventilated areas where fumes could accumulate. Emissions from the engine contain carbon monoxide, which is life threatening.
Work only during suffi cient light conditions (in daylight or suffi cient artifi cial lighting).
Do not use the lawnmower when it is raining or if the grass is wet.
Proceed especially carefully when mowing in elevated terrain (on a slope). Always mow perpendicular to the slope, parallel to the contour, and not directly up/down.
Under no condition leave the lawnmower running without supervision; if you leave the lawnmower, turn off the engine.
* Never lift the rear part of the lawnmower when starting it and always keep your limbs away from the cutting deck or the rear grass ejection chute while the engine is running.
* Never modify the engine's speed setting.
On lawnmowers with travel, release the travel lever before starting the engine.
* Never transport the lawnmower while its engine is running.
Stop the engine and disconnect the spark plug in the following cases:

• when performing any task whatsoever under the mowing deck or in the rear grass ejection chute.
• when performing maintenance, repairs or inspecting the machine.
• before carrying, lifting or transporting the lawnmower.
• when you leave the lawnmower without supervision or you are getting ready to adjust the mowing height.
• before removing and emptying the grass catcher.
• when an impact with a foreign object occurs, stop the engine and carefully inspect to ensure that there is no damage. In the event of damage, take the lawnmower to a specialised service centre for repairs.

ATTENTION: The mowing blade continues to rotate for several seconds after the engine is turned off.

• if the lawnmower is vibrating abnormally (immediately identify and remedy the cause of the vibration).
• For the purpose of ensuring safe operation, regularly check that the pins, bolts and nuts on the lawnmower are securely tightened.

ATTENTION: FUEL IS A VERY FLAMMABLE LIQUID.

* Store fuel in a suitable container.
Only add fuel in an open and well ventilated location. When handling fuel, do not smoke or use a mobile phone.
Only add fuel when the engine is turned off. Never open the fuel tank or add fuel if the engine is hot or if it is running.
If fuel is spilled, do not start the engine. Take the lawnmower away from the location where the fuel was spilled and take care to avoid possible ignition. Continue with work only after the spilled fuel has evaporated and the fuel fumes have dissipated;

After adding fuel, securely tighten the fuel tank cap and the cap on the fuel canister.

ATTENTION: Before carrying out maintenance or repairs, stop the engine and disconnect the spark plug.

9. MAINTENANCE

LAWN CARE

* Various forms of care are required depending on the type of grass area.
Therefore, always read the instructions included on seed packages with respect to the mowing height for the growing conditions in the given locality.
It is necessary to always keep in mind that the larger part of grass consists of a stem and one or more leaves. When the leaves are cut off completely, the lawn is damaged and the renewal of growth will be much more difficult.
The following instructions generally apply:

– excessively low mowing causes disruption to the roots and subsequently "spotty" appearance;
– in summer, mowing must be higher to prevent the soil from drying out;
- mowing wet grass may result in a lower efficiency of the blade due to grass catching on the blade and grass being ripped out of the ground;
- in the event of exceptionally tall grass it is appropriate to perform the first mow at the maximum permitted mowing height of the machine and then mow again only after two or three days.

The lawn will have a better appearance when it is mowed regularly over its entire area at the same height with alternating mowing directions.

MAINTENANCE

Caution! Always tilt the mower towards the handle side only (rear of the mower).

* All nuts, pins and bolts must be properly tightened so that the machine is in a safe and operational condition. Regular maintenance is the basic prerequisite for ensuring safety of the user, maintain the lawnmower's operating condition and high performance.
* Never store a machine with petrol in the fuel tank inside a building where the fumes could come within range of an open fire, sparks or sources of high temperature
Before storing in any enclosed area, allow the engine to cool down.
To reduce the risk of a fire, ensure that the lawnmower and in particular the engine, exhaust muffler, battery and also the location of spare fuel storage are free of grass, leaves or excessive amounts of lubricant.
* Regularly inspect the condition of the defl ector and the grass catcher; replace if damaged.
Drain the fuel in a well ventilated area when the engine has cooled down.
When removing or installing the mowing blade, use thick work gloves.
It is necessary to check the balance of the mowing blade every time that it is sharpened.

ATTENTION: Before carrying out maintenance or repairs, stop the engine and disconnect the spark plug.

* Regularly inspect the lawnmower and ensure that all grass deposits are removed from the underside of the chassis.

* Regularly lubricate the axle of the chassis and the bearings using a suitable lubricant.
* Regularly inspect the condition of the blades because they have a signifi cant effect on the performance of the lawnmower. Blades should always be sharp and balanced.
In regular intervals, check that all nuts and bolts are tightened. Nuts and bolts that are worn out or incorrectly tightened may cause serious damage to the engine or the frame.
If the blade strongly impacts an obstacle, stop the lawnmower and take it to an authorised service centre.
BLADE: the blade is made from pressed steel. To achieve the best possible mowing results, regularly sharpen the blades, approximately after every 25 hours of operation. Check that the blade is always correctly balanced. To do this, insert a steel axle (with a diameter of 2-3 mm) into the middle hole. If it is correctly levelled, the axis will remain in the horizontal position.
If the blade does not remain in the horizontal position, replace it.
When removing the blade, screw out the bolt, check the load bearing part of the blade. If the parts are worn out or damaged, replace them.

ATTENTION: Always use only original spare parts. Poor quality spare parts may cause serious damage to the lawnmower and create a safety hazard.

SERVICE

In the event that after purchasing the product you find any kind of defect, contact the service department. When using the product, follow the instructions contained in the included user's manual.
A complaint will not be accepted if you modified the product or if you did not follow the instructions in the user's manual.

WARRANTY DOES NOT COVER

* Normal wear and tear of operating parts of the machine as a result of its use
Servicing tasks related to standard maintenance of the machine (e.g. cleaning, lubrication, tuning, etc.). Defects caused by external effects (e.g. climatic conditions, dustiness, inappropriate use, etc.)
* Mechanical damage resulting from the machine being dropped, impact, etc.
Damages resulting from unprofessional handling, overloading, use of incorrect parts, inappropriate tools, etc.
On returned products that were not properly protected against mechanical damage during transport, the risk of potential damage is borne exclusively by the owner.

STORAGE

If you will not be using the machine for an extended period of time, store it according to the following instructions. This will extend the lifetime of the machine.
* Fully drain fuel from the fuel tank and the carburettor.
Screw out the spark plug and pour a small amount of motor oil into the socket. Gently pull the pull cord 2 to 3 times.
Use a clean cloth to clean the exterior surfaces. Store the machine in a clean dry location.

10. TECHNICAL SPECIFICATIONS

Engine RATO RV125-S
Engine type OHV, air cooled, 4-stroke
Rated power 1.9 kW
Engine rpm 2900 rpm
Displacement 127 cm	3
Starting Pull cord
Fuel tank volume 1.0 litres
Recommended fuel Petrol - lead-free, at least 95 octane
Oil tank volume 0.5 l
Recommended oil	SAE30, 15W-40
Mowing height adjustment	Central, 6 positions
Adjustable mowing height range	25-75 mm
Mowing coverage	420 mm
Wheel size	Front 150 mm, rear 200 mm
Grass catcher capacity	45 l
Chassis	steel
Declared noise level	96 dB (A)
Weight	21.7 kg

Amendments to text and technical parameters are reserved.

Changes in the text, design and technical specifications may be made without prior notice and we reserve the right to make such changes.

11. REGULAR MAINTENANCE SCHEDULE

Always carry out the regular maintenance schedule at a monthly or hourly interval – whichever comes first		Before each use	After 5 hours of operation for new machines	Every 6 months or after 25 hours of operation	Every year
Cleaning the machine, tightening the connecting screws		X
Engine oil	Level check X
	Replacement		X		X
Air fi Iter	Inspection X
	Cleaning			X
	Replacement				X
Spark plug	Inspecting & Cleaning X
	Replacement				X
Checking the mowing mechanism	Inspection X(*)
Idling Checking & Adjusting X(*)
Valve movement Checking & Adjusting X(*)
Combustion chamber Cleaning					X(*)
Fuel lines	Inspecting & Cleaning				X(*)
General preventative inspection					X(*)

*entrust this maintenance to an authorized service centre

Caution! If the mower is used in arduous or dusty conditions, change the oil and clean the air filter at more frequent intervals.

1. DETECTION AND TROUBLESHOOTING

Problem Probable	cause Procedures
Unable to start the engine	Choke valve damper in wrong position Move	the choke lever to the correct position
	The fuel tank is empty Fill the fuel tank with fuel
	The air fi lter is dirty Clean the air fi lter
	Loose spark plug Tighten the spark plug to 25-30 Nm
	The ignition cable is loose or disconnected from the spark plug	Install the ignition cable to the spark plug
	Incorrect gap between spark plug electrodes	Install a new spark plug with the correct gap between the electrodes
	Faulty ignition module Contact the repair shop
The engine is diffi cult to start or loses power	Dirt, water or old fuel in the tank	Drain the fuel and clean the tank. Fill the tank with fresh clean fuel
	Clogged air vent in fuel tank cap Clean or rep	ace the fuel fi lter cap
	The air fi lter is dirty Clean the air fi lter
	Dirt, water or old fuel in the tank	Drain the fuel and clean the tank. Fill the tank with fresh clean fuel
	Clogged air vent in fuel tank cap Clean or rep	ace the fuel fi lter cap
	The air fi lter is dirty Clean the air fi lter
The engine runs irregularly	Faulty spark plug	Install a new spark plug with the correct gap between the electrodes
	Incorrect gap between the electrodes	Set the gap between the electrodes to 0.7 - 0.8 mm
	The air fi lter is dirty Clean the air fi lter
The engine is idling poorly	The air fi lter is dirty Clean the air fi lter
	The air gaps in the engine cover are clogged	Remove debris from the gaps
	The cooling fi ns and air passages below the engine fan are clogged	Remove debris from cooling fi ns and air passages
The engine stops at high speed	The gap between the spark plugs is too small	Set a gap of 0.7 to 0.8 mm
The motor is overheating	Limited airfl ow	Remove any debris from the gaps on the engine cover, fan cover, and air passages
	Unsuitable spark plug	Install a new spark plug with the correct gap between the electrodes
The mower vibrates violently	The cutting unit is loose Tighten the mower blade
	The cutting unit is not balanced	The mower blade must be balanced
	Bent crankshaft	Contact the repair shop

13. DISPOSAL

INSTRUCTIONS AND INFORMATION REGARDING THE DISPOSAL OF USED PACKAGING MATERIALS

Dispose of used packaging material at a site designated for waste in your municipality.

The machine and its accessories are manufactured from various materials, e.g. metal and plastic.

Take damaged parts to a recycling centre. Inquire at the relevant government department.

This product meets all the basic requirements of EU directives that apply to it.

Changes in the text, design and technical specifications may be made without prior notice and we reserve the right to make these changes.

Translation of the original user's manual.

Close-up of a black tool with a white handle attachment, labeled 'Obr. 2b' (no other text or symbols visible)

2. SESTAVENI KOŠE

Two black plastic containers with a curved arrow indicating rotation, shown from different angles (no text or symbols)

Illustration of hands performing a rope knotting technique (no text or symbols)

Illustration of a hand holding a tool with an arrow indicating motion, no text or symbols present

NASTAVENÍ VÝŠKY SEČENÍ

Technical line drawing of a mechanical component with no visible text or symbols

VÝMĚNA MOTOROVÉHO OLEJE

Technical line drawing of a mechanical assembly with labeled components (no readable text or symbols)

Udržujte ostatné osoby mimo pracovnej oblasti.

Close-up of a black tool with a white handle attachment, labeled 'Obr. 2b' (no other text or symbols visible)

2. ZOSTAVENIE KOŠA

Two black plastic containers with a curved arrow indicating rotation, shown from different angles (no text or symbols)

Illustration of a person performing a rope knotting technique with a black arrow indicating rotation (no text or symbols)

Illustration of a hand holding a tool with an arrow indicating motion, no text or symbols present

Obr. 9

NASTAVENIE VÝŠKY KOSENIA

Technical line drawing of a mechanical component with no visible text or symbols

VÝMENA MOTOROVÉHO OLEJA

Technical line drawing of a mechanical assembly with labeled components (no readable text or symbols)

Close-up of a black tool with a white handle attachment, labeled '2b. ábra' (no other text or symbols)

Two black plastic containers with a curved arrow indicating a change or transformation, labeled '4. ábra' (no other text or symbols)

Illustration of hands performing a rope knotting technique (no text or symbols)

Illustration of a hand holding a tool with an arrow indicating motion, no text or symbols present

Technical line drawing of a mechanical assembly with labeled components (no readable text or symbols)

Close-up of a black tool with a white handle attachment, labeled 'Rys. 2b' (no other text or symbols visible)

2. ZAKŁADANIE KOSZA

Two black plastic containers with a curved arrow indicating rotation, no text or symbols present

Illustration of a person performing a rope knotting technique (no text or symbols present)

Illustration of a hand holding a tool with an arrow indicating motion, no text or symbols present

USTAWIENIA WYSOKOŚCI KOSZENIA

Technical line drawing of a mechanical component with no visible text or symbols

WYMIANA OLEJU SILNIKOWEGO

Technical line drawing of a mechanical assembly with labeled components (no readable text or symbols)

1. WYKRYWANIE I USUWANIE PROBLEMÓW

Home & Garden Performance

Model /Modell /Modelis:

Conditions of guarantee

This product is warranted for the period of 24 months from the date of purchase to the end-user. Warranty is limited to the following conditions. Warranty is referred only to the customer goods using for common domestic use. The claim for service can be applied either at dealer's shop where the product was bought, or at below mentioned authorized service shops. The end-user is obligated to set up a claim immediately when the defects appeared but only till the end of warranty period. The end-user is obligated to cooperate to certify the claiming defects. Only completed and clean (according to hygienic standards) product will be accepted. In case of eligible warranty claim the warranty period will be prolonged by the period from the date of claim application till the date of taking overthe product by end-user, or the date the end-user is obligated to take it over. To obtain the service under this warranty, end-user is obligated to certify his claim with duly completed following documents: receipt, certificate of warranty, certificate of installation... This warranty is void especially if apply as follows: ■ Defects which were put on sale. ■ Wear-out or damage caused by common use. ■ The product was damaged by unprofessional or wrong installation, used in contrary to the applicable instruction manual, used in contrary to legal enactment and common process of use or used for another purpose which has been designed for. ■ The product was damaged by uncared-for or insufficient maintenance. ■ The product was damaged by dirt, accident of force majeure (natural disaster, fire, flood, ...). ■ Defects on functionality caused by low duality of signal, electromagnetic field interference etc. ■ The product was mechanically damaged (e.g. broken button, fall...). ■ Damage caused by use of unsuitable media, fillings, expendable supplies (batteries) or by unsuitable working conditions (e.g. high temperatures, high humidity, quakes,...). ■ Repair, modification or other failure action to the product by unauthorized person ■ End-user did not prove enough his right to claim (time and place of purchase). ■ Data on presented documents differs from data on products. ■ Cases when the claiming product can not be identified according to the presented documents (e.g. the serial number or the warranty seal has been damaged).

[e-mail]

www.fastcr.cz

Fast Plus, a. s.

Na Pántoch 18

SK 831 06 Bratislava

Slovenská republika

Tel.: [phone]

Fax: [phone]

[e-mail]

www.fastplus.sk

Jótállási jegy

Black and white photo of a Flöhmann lawn mower (no visible text or symbols)