VP-4120 - Broom Concept - Free user manual and instructions

Product Type	2-in-1 Stick Vacuum Cleaner (Hand-held and Stick)
Model	VP-4120
Brand	Concept
Battery Voltage	DC 18.5 V
Charging Adapter Input	AC 100-240 V, 50/60 Hz
Charging Adapter Output	DC 24 V, 500 mA
Power Input	100 W
Suction Power	≥ 8 kPa
Noise Level	78 dB(A)
Charging Time	Approx. 6 hours
Operating Time	Approx. 25-40 minutes
Battery Cycle Life	Approx. 500 cycles
Protection Class	III
Filters	Coarse filter (Order No. 42390809), Fine filter (Order No. 42390810)
Accessories Included	Turbo brush, Upholstery nozzle, Slot nozzle, Charging base
Operation Modes	Stick vacuum, Hand-held vacuum (detachable)
Dust Receptacle	Cyclone type, removable and washable
Cleaning and Maintenance	Empty dust receptacle after each use; clean filters with soft brush; wash filters in lukewarm water if heavily soiled; do not use detergents; dry thoroughly before reuse
Safety Features	Automatic shut-off when not in use? Not specified; ensure filters are installed; do not vacuum liquids or hot objects; keep away from children
Warranty	24 months (6 months for accumulator)

Frequently Asked Questions - VP-4120 Concept

How long does it take to fully charge the Concept VP-4120 vacuum cleaner?

The first charge or after full discharge takes approximately 6 hours. Always charge the vacuum cleaner when the battery is fully discharged to maximize battery life.

What should I do if the suction power of my Concept VP-4120 decreases?

Reduced suction power is usually caused by a full dust receptacle or clogged filters. Empty the dust receptacle and clean or replace the filters. Also check the nozzle and turbo brush for blockages.

Can I use the Concept VP-4120 to vacuum liquids or wet surfaces?

No, the vacuum cleaner is designed for dry vacuuming only. Do not vacuum liquids, wet objects, or flammable fluids. Using it on wet surfaces may damage the device and cause electric shock.

How do I clean the filters of the Concept VP-4120?

Filters can be cleaned by gently shaking or using a soft brush. If heavily soiled, wash them in lukewarm water without detergents, then let them dry completely before reinstalling. Never use a hair dryer.

What is the operating time of the Concept VP-4120 on a full charge?

The operating time is approximately 25 to 40 minutes, depending on the power setting and surface type.

How can I detach the hand-held vacuum from the stick?

Press the release button on the stick part (see Fig. 4 in the manual) and pull the portable part upwards. You can then use it as a hand-held vacuum.

What accessories are included with the Concept VP-4120?

The package includes a turbo brush, upholstery nozzle, slot nozzle, and a charging base. A charging adapter is also provided.

How do I know when the battery is fully charged?

The charging indicator light on the vacuum cleaner turns green when the battery is fully charged. Unplug the charging adapter at that point to preserve battery life.

What is the warranty period for the Concept VP-4120?

The product comes with a 24-month warranty. The battery (accumulator) has a 6-month warranty as it is considered a consumable part.

Can I replace the battery myself?

Yes, the battery is replaceable. To remove it, unscrew the cover on the lower side of the portable part and disconnect the clamps or cut the lead-in cables. Only use a genuine replacement battery (Order No. 44291599).

USER MANUAL VP-4120 Concept

Black concept vacuum cleaner with extended arm and propeller (no visible text or symbols)

VP 4120

PODĚKOVÁNÍ

Close-up of a black handheld vacuum cleaner with an arrow pointing to the lid (no visible text or symbols)

ČISTĚNÍ A VÝMĚNA FILTRŮ

Close-up of a black handheld vacuum cleaner with an arrow pointing to the component (no visible text or symbols)

ČISTENIE A VÝMENA FILTROV

Close-up of a black handheld vacuum cleaner with a curved arrow indicating rotation (no visible text or symbols)

Rys. 1 Rys. 2

Close-up of a black mechanical device with a handle and base (no visible text or symbols)

Rys. 3

ŁADOWANIE AKUMULATORA

Close-up of a black handheld vacuum cleaner with an arrow pointing to the component (no visible text or symbols)

CZYSZCZENIE I WYMIANA FILTRÓW

Close-up of a black concept air purifier device with a curved arrow indicating rotation (no text or symbols visible)

1. ábra 2. ábra

Close-up of a black mechanical device with a curved handle and base (no visible text or symbols)

1. ábra

AZ AKKUMULÁTOR FELTÖLTÉSE

Two different types of hair purifiers, one with a left-side arrow and the other with an arrow, shown without any text or symbols.

LIETOŠANA

PUTEKLSÜCÉJA SALIKŠANA

PIEZIME:

Close-up of a black handheld vacuum cleaner with a curved arrow indicating rotation (no visible text or symbols)

Zim. 1 Zim. 2

Close-up of a black mechanical device with a conical top and base (no visible text or symbols)

Zim. 3

AKUMULATORA UZLĀDĒŠANA

The image is too blurry to recognize any text content.

KOPŠANA

Two different types of hair purifiers, one with a black outline and arrow pointing to the left, and another with an arrow pointing to the right (no text or symbols visible)

FILTRU TİRİŞANA UN NOMAINA

Putekjsücêja filtrus var notirit, mehâniski kratot un tirot tos ar mikstu suku. Loti plesämotus filtrus var ani nomazgât siltä üdeni, tirot ar mikstu suku. Nelietojiet mazgâšanas lidzeklus.

Thank you for purchasing a Concept product. We hope you will be satisfied with our product throughout its service life.

Please study the entire Operating Manual carefully before you start using the product. Keep the manual in a safe place for future reference. Make sure that any persons handling the vacuum cleaner are also familiar with this Operating Manual.

Technical parameters
Accumulator voltage DC 18,5 V
Charging adapter voltage	input: AC 100–240V – 50/60Hz output: DC 24 V, 500 mA
Power input 100 W
Noise level 78 dB (A)
Suction power ≥ 8 kPa
Time until fully charged approx.	6 hours
Time of operation approx. 25–40 min

Reinforced insulation. Protection class III.

IMPORTANT SAFETY PRECAUTIONS

• Use the unit only as described in this operating manual.
• Make sure the mains voltage corresponds to the values on the rating plate of the charging adapter.
• Do not leave the unit unattended when switched on.
• When disconnecting the charging adapter from the wall outlet, never pull the power cord. Grasp the plug and disconnect it by pulling.
• Do not allow children or unskilled people to handle the unit. Use the unit out of the reach of these individuals.

• Take extra care when using the unit near children.

- Don't let anyone use the unit as a toy.

- Use only accessories recommended by the manufacturer.

- Never use a charging adapter with a damaged power cord or plug. Contact an authorized service center immediately to have the defective components repaired or replaced.

- Keep the product away from heat sources such as radiators, ovens, etc. Do not expose the product to direct sunlight or moisture.

- Do not touch the unit with wet or damp hands.

- Do not insert any objects into the openings. Do not use the vacuum cleaner if any openings are obstructed.

- Extra care should be taken while vacuuming on stairs.

- If the suction inlet of the unit is obstructed, turn the unit off and remove the blockage before resuming operation.

- Tum the product off and disconnect the charging adapter from the mains outlet before installing accessories, performing maintenance, or in the case of any failure.

- The unit is suitable for domestic use only. It is not designed for commercial operation.

- Do not vacuum any burning objects such as cigarettes, matches, or hot ash.

EN

concept

concept

EN

• Do not use the unit in wet rooms. Do not vacuum wet objects, liquids, or flammable fluids such as gasoline. Do not use the vacuum cleaner in areas where such substances may be present.
• Never use the vacuum cleaner without filters. Before each use, make sure that the filters of the vacuum cleaner are installed properly.
• Do not immerse the power cord, charging adapter, or appliance into water or any other liquid.
• Check the appliance as well as the power cord of the charging adapter for damage regularly. Do not switch on a damaged unit.
• Turn the unit off and let it cool down before maintenance and after use.
• Prior to vacuuming, it is necessary to remove large or sharp objects which could damage a filter of the vacuum cleaner from the surface to be cleaned.
• Do not use the unit if the filters are fouled.
• Do not discard the accumulator of the unit into the fire or expose it to temperatures above 40 °C.
• Do not touch the driven moving parts while the unit is in operation.
• Do not repair the appliance yourself. Contact an authorized service center.
• This appliance may be used by children 8 years of age and older and by persons with physical or mental impairments or by inexperienced persons if they are properly supervised or have been informed about how to use of the product in a safe manner and understand the potential dangers. Children must not play with the appliance. This appliance may be cleaned by children 8 years of age and older if they are properly supervised. Keep this appliance and the power cord out of reach of children younger than 8 years of age.

Failure to follow the manufacturer's instructions may lead to refusal of warranty repair.

PRODUCT DESCRIPTION

1 Stick part holder
2 Stick part
3 Stick part switch
4 Portable part with a motor
5 Dust receptacle with cyclone unit
6 Charging indicator
7 Portable part switch
8 Turbo brush
9 Coarse filter
10 Fine filter

Accessories

A Charging adapter
B Nozzle for upholstery
C Slot nozzle
D Charging base
A Charging adapter
B Nozzle for upholstery
C Slot nozzle
D Charging base

OPERATING INSTRUCTIONS

ASSEMBLING THE VACUUM CLEANER

NOTE:

Always disconnect the plug of the charging adapter from the mains outlet prior to mounting or removing accessories!

1. Inserting the portable part of the vacuum cleaner Insert the nozzle of the portable part into the stick part of the vacuum cleaner and push the portable part holder until you hear a clicking sound – which indicates that the correct position has been reached (Fig. 1). To release the portable part, press releasing button on the stick part of the vacuum cleaner.

2. Erecting the holder of the vacuum cleaner stick part Tilt out the holder of the vacuum cleaner stick part until you hear a clicking sound – which indicates that the correct position has been reached (Fig. 2). To fold press the releasing button on the holder of the vacuum cleaner stick part.

3. Mounting the turbo brush Put the turbo brush on the lower end of the vacuum cleaner stick part until you hear a clicking sound – which indicates that the correct position has been reached (Fig. 3). To dismount the turbo brush press the releasing button on the lower end of the vacuum cleaner stick part.

Close-up of a black CO2EPC vacuum cleaner with a curved arrow indicating rotation (no text or symbols visible)

Fig. 1 Fig. 2

Close-up of a black mechanical device with a pointed tip and textured grip (no visible text or symbols)

Close-up of a black industrial vacuum cleaner with a conical top and base (no visible text or symbols)

Fig. 3

CHARGING THE ACCUMULATOR

Prior to the first use or if the accumulator of the vacuum cleaner is fully discharged, let the vacuum cleaner charge for approximately 6 hours.

Connect the power cord and plug the charging adapter into the wall outlet. If you want to keep the service life of the accumulator as long as possible, charge it only after it has been discharged completely.

The service life of the accumulator is approximately 500 charging cycles.

Note: To keep the longest possible service life of the accumulator, always charge it when fully discharged, and, when fully charged (the charging indicator light is green), disconnect the charging adaptor (A) from the mains.

VP 41

EN

concept

concept

EN

USING THE VACUUM CLEANER

NOTE: Prior to using the vacuum cleaner, please make sure that the filters have been installed properly.

STICK VACUUM CLEANER

1. Switch on the vacuum cleaner using the switch on the stick part holder.
2. After use, switch off the vacuum cleaner with the switch on the stick part holder.

HAND-HELD VACUUM CLEANER

1. Press the latches on the stick part (see Fig. 4) to detach the portable part of the vacuum cleaner.
2. Switch the vacuum cleaner on using the switch on the portable part holder.
3. After use, release the switch on the portable part holder to switch the vacuum cleaner off.

CHECKING THE DUST RECEPTACLE LEVEL

If the suction power of the vacuum cleaner drops or the dust receptacle is full, empty it and clean the filters of the vacuum cleaner.

MAINTENANCE

As a preventative measure, we recommend emptying the dust receptacle and cleaning the filters of the vacuum cleaner after each use.

EMPTYING THE DUST RECEPTACLE

1. Disconnect the charging adapter from the power mains.
2. Detach the portable part of the vacuum cleaner from the stick part.
3. Hold the portable part of the vacuum cleaner with the dust receptacle down.
4. Press and hold the dust receptacle latch and turn the dust receptacle slightly to release it (Fig. 5).
5. Remove both filters and empty the dust receptacle of the vacuum cleaner.
6. Reverse the steps to fit both filters and mount the dust receptacle back on the portable part of the vacuum cleaner.

Fig. 4 Fig. 5

Close-up of a black handheld vacuum cleaner with an arrow pointing to the component (no visible text or symbols)

CLEANING AND REPLACING THE FILTERS

The filters of the vacuum cleaner can be cleaned by mechanical shaking and cleaning with a soft brush. Heavily fouled filters can be washed after this step and cleaned with a soft brush in lukewarm water. Do not use detergents.

It is important to let the wet parts dry thoroughly. Wet filters might be damaged if used for vacuuming!

Do not use a hair dryer for drying!

40

VP 4120

Note: Wet cleaning can cause more wear and tear of the filters, and a correspondingly shorter service life.

• The filters should be cleaned or replaced whenever they are visibly fouled, or when the suction power decreases. The filters should be checked after each use of the vacuum cleaner.
• Never use the vacuum cleaner without properly installed filters to avoid damage to the appliance.
• Suitable filter types are available at your local retailer, or they can be ordered from the manufacturer.

CLEANING AND MAINTENANCE

The vacuum cleaner and its accessories can be cleaned with a damp cloth.

Do not immerse the power cord, charging adapter, or appliance into water or any other liquid.

Do not use aggressive substances for cleaning, such as solvents or abrasives!

TROUBLESHOOTING

Problem Cause Solution
Motor does not run. Accumulator is discharged. Charge the accumulator.
Reduced suction power.	Dust receptacle full or clogged.	Empty and clean the dust receptacle.
	Obstructed filter. Clean or replace the filter.
	Clogged nozzle or turbo brush of the vacuum cleaner.	Check and clear the air passage on the suction and discharge sides.
Although the accumulator is fully charged, the operating time is shorter than 2 minutes.	The accumulator service life is over.	The accumulator needs to be replaced.
Vacuum cleaner heats up.	Slight heating of the vacuum cleaner is normal and cannot be considered a failure.

ACCESSORIES

The following accessories can be purchased with the unit:

Fine filter Ord. No. 42390810 Price: See price list

Coarse filter Ord. No. 42390809 Price: See price list

Accumulator Ord. No. 44291599 Price: See price list

SERVICE

Any larger maintenance or repairs requiring intervention into the internal parts of the product shall only be performed by an authorized service

VP 4120

41

EN

concept

concept

DE

ENVIRONMENTAL PROTECTION

• Recycle packaging materials and old appliances rather than throwing them away.
• The appliance box may be disposed of at a sorted waste collection point.
• Deliver polyethylene (PE) plastic bags to a waste collection facility for recycling.

Recycling the product at the end of its service life

A symbol on the product or its packaging indicates that this product should not be disposed of as household waste. It must be taken to a collection point authorised for recycling electric and electronic equipment. By making sure this product is disposed of properly, you will help prevent negative effects on the environment and human health that would otherwise result from inappropriate disposal of this product. You can learn more about recycling this product from your local authorities, a household waste disposal service, or in the store where you purchased this product.

Disposal of accumulators and battery cells

If an appliance contains an accumulator or a battery cell, these components contain substances that may damage the environment when decomposing. Prior to the appliance disposal or the accumulator or battery cell replacement, it is necessary to remove the original component and take it to a suitable designated collection yard.

WARNING!

An accumulator or battery cell:

- Never throw into a fire!

- Never disassemble it!

- Never short-circuit its terminals!

Should an accumulator or battery cell leakage occur, the leaked solution is of an alkaline character. If your skin gets stained, rinse it immediately with soap and water and seek medical treatment.

To remove the accumulator, screw-off the cover on the lower side of the portable part. Disconnect the accumulator by separating the clamps or cutting the lead-in cables of the accumulator.

This product meets all the basic EU regulation requirements that relate to it.

Changes to the text, design and technical specifications may occur without prior notice and we reserve the right to make these changes.

42VP 4120

DANKSAGUNG

Close-up of a black handheld vacuum cleaner with a curved arrow indicating rotation (no visible text or symbols)

Abb. 1 Abb. 2

Close-up of a black mechanical device with a conical top and base (no visible text or symbols)

Abb. 3

BATTERIELADUNG

Two black handheld vacuum cleaner units, one with a left arrow and label Abb. 4 Abb. 5, the other with an arrow pointing to a single component (no text on device itself)

The manufacturer (or importer) is responsible for ensuring the product complies with the requirements of applicable legal regulations as well as those of the relevant technical standards. Moreover, they are responsible for ensuring the product has the properties the manufacturer described in documents related to the goods or those reasonably expected by the customer with regard to the nature of the goods or based on advertising produced by the manufacturer, and further they are responsible for ensuring the product is fit for the purpose proposed by the manufacturer or that a product of the same type is normally used for.

The quality warranty term is 24 months from product takeover by the customer.

In terms of these warranty conditions, a defective accumulator is an accumulator that is electronically malfunctioning (i.e. it does not communicate with the basic unit, its charging or discharging circuits are faulty, etc.) or has an internal short-circuit.

Defects or changes of parameters resulting from normal use and/or wear (e.g. natural decrease in capacity) are not, in any event, considered to be defects in terms of warranty.

The warranty for the accumulators is granted for 6 months. In terms of these warranty conditions, an accumulator has the nature of consumables. For details, see "Consumables".

Consumables

For consumables (batteries, etc.) we guarantee the maintenance of technical parameters for 6 months, unless the product has been damaged as a result of improper use or its service life has expired.

The warranty does not apply to wear and tear caused by regular use. The customer shall not be entitled to any warranty claims if, prior to taking the product over, they knew the product contained a defect or if the defect is attributable to the customer.

Product data

Model:
Production number:
Date of purchase: Seal and signature of vendor:

The warranty specifically does not apply:

• if the product installation, operation and service conditions stipulated in the product operating manual have not been adhered to,
• to malfunctions caused due to mechanical, heat or chemical damage, short circuit, over voltage or incorrect installation,
• to malfunctions caused by an inexpert third-party intervention,
  • to malfunctions caused by natural disaster,
  • to malfunctions caused by insufficient or inappropriate maintenance in violation of the operating manual, including malfunctions caused by water and other sediments,
• to changes in colour of the heating surface or to scratching of the surface caused as a result of using the products in an unusual manner,
• to appearance and functional changes caused by exposure to sunlight, thermal radiation of water and other sediments,
• if the service life of certain product parts expires, e.g. for accumulators, bulbs, etc.

The warranty does not apply to any products and services provided along with the product (gifts, promotional articles, etc.).

Filing a complaint

A complaint against a product defect must be filed as soon as identified, yet no later than before the end of the warranty term.

The customer must file a product complaint with the dealer from which they have purchased the product, or with any authorised service centre, a list of which is included in the product package, or available at www.my-concept.com.

While fi ling a product complaint, the product must be duly cleaned and securely packed so as to prevent any damage during its transport to an authorised service centre, where relevant, unless the product is delivered in person.

The customer must submit proof of having concluded a purchase contract for the product by producing the receipt.

While fi ling their complaint, the customer must indicate the noted defect and identify the preferred complaint application method.

Complaints processing

As long as the noted defect may be removed, the user has the right to have the defect duly removed free of charge on a timely basis.

Where such a procedure is not reasonable with regard to the nature of the defect, the user may require to be supplied a new defect-free product (replacement), or, where the defect applies to a part of the product only, replacement of the part concerned. However, if replacement of the product or any part thereof is not proportionate with regard to the nature of the defect, especially if the defect can be removed without undue delay, the customer has the right to have the defect removed free of charge.

If the noted defect is not removable, or if the customer becomes entitled to replacement of the product or a part thereof, yet the replacement is not possible, for example due to the product having been sold out, the customer has the right to return the product (withdrawal from the contract).

The customer shall have the right to a new product (replacement) or to replacement of a part of the product even if the defect can be removed, provided they cannot properly use the product due to repeated occurrence of the defect or due to a high number of such defects. In such a case, the customer also has the right to return the product (by withdrawing from the contract).

If the product is not returned (the customer does not withdraw from the contract), or if the customer does not apply the right to a new defect-free product (replacement), to replacement of a part thereof or to repair of the product, they may request a reasonable discount. The customer also has a right to a reasonable discount if a new defect-free product cannot be supplied to them, or if a product part cannot be replaced or the product repaired unless the situation is remedied within a reasonable time limit, or if remedying the situation would create major discomfort on the part of the customer.

The seller, authorised service centre or a staff member authorised by them must decide about each complaint immediately or within three business days in complicated cases. This term does not include a reasonable period of time, depending on the type of product concerned, required for the defect to be assessed by an expert. A complaint, including defect removal, must be dealt with without any undue delay, yet no later than within 30 calendar days of the complaint fi ling date, unless the seller and the customer agree on a later deadline.

On returning the product (withdrawing from the contract) the customer must return any accessories and documents supplied along with the product.

The customer does not have the right to keep the defective parts and components of the product replaced as part of a repair of the product.

This shall be without prejudice to any other rights the customer may have in relation to the purchase of the product.

Remark: Complaints against products damaged in transport are governed by the carrier's complaints procedure.

Manufacturer

Jindřich Valenta - ELKO Valenta

Vysokomýtská 1800, 565 01 Choceň

Czech Republic

tel.: [phone]

fax [phone]

Company ID No. 13216660

email: [e-mail]

www: www.my-concept.com

concept

Jindřich Valenta – Concept Czech Republic

Vysokomýtská 1800, 565 01 Choceň

Tel. [phone], Fax: [phone]

www.my-concept.cz

SK

ELKO Valenta – Slovakia, s.r.o.

Hurbanova 1563/23, 911 01 Trenčín

Tel.: [phone], Fax: [phone]

www.my-concept.sk

PL

Elko Valenta Polska Sp. Z. o. o.