HG09501 - Uncategorized PARKSIDE - Free user manual and instructions

Product Type	Hands-free LED Magnifier with Helping Hands
Model	HG09501
Brand	Parkside
Magnification	2.5x / 5x (rotating lens)
Lighting	2 x LED (non-replaceable, 0.06 W each)
Power Supply	3 x LR1130 batteries (1.5 V each, included)
Operating Voltage	4.5 V DC
Dimensions (with base plate)	Approx. 20 x 11.9 x 16 cm (W x H x D)
Base Material	Plastic with metal clamps and holder
Clamps	2 alligator clips on adjustable arms
Additional Tools	Soldering iron holder, repair device (adjustable ball joint)
Intended Use	Magnifying objects, aiding soldering/crafts with shadow-free LED light
Indoor Use Only	Yes
Not for Commercial Use	Yes
Warnings	Do not look into direct light; keep away from children; fire risk from concentrated light
Battery Safety	Keep batteries away from children; dispose properly; do not recharge non-rechargeable
Cleaning	Use dry, lint-free cloth; avoid abrasives; do not immerse in water
Replacement Parts	Batteries (LR1130); other parts not intended for user replacement
Compliance	CE marked
Package Contents	1 precision LED magnifying glass, 3 x LR1130 batteries, 1 operating instructions

Frequently Asked Questions - HG09501 PARKSIDE

How do I change the batteries in my Parkside HG09501 Helping Hand LED Magnifier?

Use a suitable screwdriver (not included) to remove the battery compartment cover. Replace with 3 x LR1130 1.5V batteries, ensuring correct polarity as shown inside. Reattach the cover and tighten.

What should I do if the LED lights do not turn on?

First, check if the batteries are installed correctly and have sufficient charge. Replace flat batteries with new LR1130 cells. Also ensure the on/off switch is set to ON.

Can I use this magnifier for soldering?

Yes, it is designed for precision work including soldering. The soldering iron holder and alligator clips help hold parts. However, do not leave a hot soldering iron unattended in the holder.

How should I clean the lens and the product?

Use a dry, lint-free cloth to gently clean the lens. For the body, a slightly moistened cloth can be used. Do not use abrasive or corrosive cleaners, and never immerse the product in water.

Is the magnifying glass suitable for direct sunlight?

No, never look through the magnifier at the sun or other strong light sources as it can cause severe eye injury. Also, direct sunlight focused by the lens can create a fire hazard.

How can I adjust the magnifier and clamps?

The magnifying glass and clamps have ball joints and retaining screws. Loosen the screws, position the components as desired, then tighten the screws. Height can be adjusted by sliding the fixing clamps on the support rod.

What type of batteries does the Parkside HG09501 use?

It requires 3 x LR1130 (alkaline) batteries, 1.5V each. These are button cell batteries often used in small electronics.

Can I use the product with rechargeable batteries?

The manual recommends only specified non-rechargeable batteries. Using rechargeable batteries may affect performance and safety. Do not attempt to recharge non-rechargeable batteries.

Is the LED bulb replaceable?

No, the LED bulbs are non-replaceable. If they fail, the entire magnifying glass unit may need replacement. Ensure batteries are fresh before concluding LED failure.

How can I attach the base plate?

Use the included screws to fasten the base plate to the base as shown in Figure E of the manual. A suitable screwdriver (not included) is required.

USER MANUAL HG09501 PARKSIDE

Black-and-white photo of a precision optical bench with a magnifying glass and spring, no visible text or symbols.

HELPING HAND LED MAGNIFIER

GB

HELPING HAND LED MAGNIFIER

Operation and safety notes

HU

FINOMMECHANIKAI MÜSZERÉSZKÉSZLET LEDNAGYÍTÓVAL

LED LUPA NA JEMNOU MECHANIKU

SÚPRAVA NA JEMNÚ MECHANIKU S LED LUPOU

Pokyny pre obsluhu a bezpečnostné pokyny

DE AT CH

FEINMECHANIKER-SET MITLED-LUPE

GB Operation and safety notes Page 5

Intended use......Page 6

Description of parts......Page 7

Technical data......Page 8

Includes......Page 9

Safety Page 9

General safety information......Page 9

Safety instructions for batteries/ rechargeable batteries......Page 11

Before initial use ...... Page 12

Inserting the batteries......Page 13

Attaching the repair device....Page 13

Mounting the magnifying glass......Page 13

Placement of the base......Page 14

Mount the base plate ......Page 14

Use Page 14

Using the product......Page 14

Changing the batteries ...... Page 15

Troubleshooting Page 16

Cleaning and maintenance ......Page 16

Disposal Page 17

Service Page 18

List of pictograms used
	Direct current/voltage
	CE mark indicates conformity with relevant EU directives applicable for this product.
	Safety informationInstructions for use

Helping Hand LED Magnifier

- Introduction

We congratulate you on the purchase of your new product. You have chosen a high quality product. The instructions for use are part of the product. They

contain important information concerning safety, use and disposal. Before using the product, please familiarise yourself with all of the safety information and instructions for use. Only use the product as described and for the specified applications. If you pass the product on to anyone else, please ensure that you also pass on all the documentation with it.

- Intended use

The product is designed for 2.5- / 5-fold magnification of objects. The integrated LEDs only serve for better contrast and shadow-free visualization of the object to be enlarged.

In addition, the product has 2 fixing clamps and a soldering iron holder. Other uses or changes to the product are considered to be contrary to the Intended use and may harbour risks of injury and damage. The manufacturer does not accept any liability for injury or damage resulting from use of this product contrary to its Intended use. The product is intended for indoor use only. The product is not intended for commercial use or for use in other application.

Not suitable for ordinary lighting in household room illumination.

• Description of parts

1 Precision engineer's LED magnifying glass
2 Lens (magnification 2.5 / 5 times)
3 Battery compartment cover
4 Battery compartment
5 Ball joint
6 Retaining screw (lens ball joint)
7 Magnifying glass fixing clamp
8 Retaining screw (magnifying glass height adjustment)
9 On/off switch
10 Supporting rod (height adjustment)
11 Fixing clamp (repair device)
12 Retaining screw (repair device height adjustment)
13 Soldering iron holder
14 Base
15 Repair device

16 Retaining screw (repair device ball joint)
17 Retaining screw (repair device)
18 Alligator clips
19 Retaining screws (alligator clips)
20 LED lamps (Fig. B)
21 Batteries (inside battery compartment) (Fig. C)
22 Supporting rod (holding Alligator clips)
23 Locking screws (tightening Alligator clips)
24 Insulating tape
25 Base plate
26 Screw (for fixing the base plate)

- Technical data

Operating voltage: 4.5 volts =

Batteries: 3 x 1.5 V, type LR1130

Max. power rating: 2 x 0.06 W

Bulbs: 2 x LED (not replaceable)

Magnification /

magnifying glass: 2.5 / 5 times

Dimensions (with

base plate 25): approx. 20 x 11.9 x 16 cm (W x H x D)

Chromaticity

coordinate: X < 0.27 or X > 0.530; Y < -2.3172 X

$$ + 2. 3 6 5 3 X - 0. 2 1 9 9 \text {or} Y > - 2. 3 1 7 2 X ^ {2} $$

$$ + 2. 3 6 5 3 \times - 0. 1 5 9 5 $$

- Includes

Immediately after unpacking please check the package contents for completeness and if all parts and the product are in good condition. Do not under any circumstances use the product if the delivery is incomplete.

1 Precision LED magnifying glass
3 Batteries, 1.5 V=, LR1130
1 Operating Instructions

Safety

- General safety information

KEEP ALL THE SAFETY ADVICE AND INSTRUCTIONS IN A SAFE PLACE FOR FUTURE REFERENCE!

DANGORFDEATH

AND ACCIDENTS FOR TODDLERS AND

CHILDREN! Never leave children unsupervised

with the packaging material. The packaging material represents a danger of suffocation. Children frequently underestimate the dangers. Always keep children away from the packaging material. This is not a toy.

This product can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge

if they have been given supervision or instruction concerning use of the product in a safe way and understand the hazards involved. Children shall not play with the product. Cleaning and user maintenance shall not be made by children without supervision.

CAUTION! RISK OF INJURY! Please do not use this product if you find that it is damaged in any way.

Check whether all of the parts are correctly fitted. If the product is not correctly assembled there is a danger of injury.

- Keep the product away from humidity.

CAUTION! RISK OF EYE INJURIES! Never look through the product into the sun or other sources of light. Severe eye injuries may be the result.

CAUTION! DANGER OF FIRE!

Never expose the product to direct sun-light or other sources of light. Never leave the product unattended. Otherwise there is a danger of fire resulting from concentrated rays of light and concentrated heat.

The product must be stored in a dark environment.
Do not subject the product to any extreme temperatures or severe mechanical stress. Otherwise this may result in deformation of the product.
Make sure that the lens does not come into contact with sharp or pointed objects. Otherwise this may result in damage to the product.
Do not leave the soldering gun (separate device) unattended whilst on. The soldering iron holder 13 is only suitable for holding the soldering iron for a limited time.

Safety instructions for batteries / rechargeable batteries

■ DANGER TO LIFE! Keep batteries/rechargeable batteries out of reach of children. If accidentally swallowed seek immediate medical attention.
■ Swallowing may lead to burns, perforation of soft tissue, and death. Severe burns can occur within 2 hours of ingestion.
DANGER OF EXPLOSION! Never recharge

non-rechargeable batteries. Do not short-circuit batteries/rechargeable batteries and/or open them. Overheating, fire or bursting can be the result.

■ Never throw batteries / rechargeable batteries into fire or water.
Do not exert mechanical loads to batteries / rechargeable batteries.

Risk of leakage of batteries / rechargeable batteries

Avoid extreme environmental conditions and temperatures, which could affect batteries / rechargeable batteries, e.g. radiators / direct sunlight.
If batteries / rechargeable batteries have leaked, avoid contact with skin, eyes and mucous membranes with the chemicals! Flush immediately the affected areas with fresh water and seek medical attention!

WEAR PROTECTIVE GLOVES! Leaked or

damaged batteries/rechargeable batteries can cause burns on contact with the skin.

Wear suitable protective gloves at all times if such an event occurs.

In the event of a leakage of batteries / rechargeable batteries, immediately remove them from the product to prevent damage.
Only use the same type of batteries / rechargeable batteries. Do not mix used and new batteries / rechargeable batteries.
■ Remove batteries / rechargeable batteries if the product will not be used for a longer period.

Risk of damage of the product

Only use the specified type of battery / rechargeable battery!
Insert batteries / rechargeable batteries according to polarity marks (+) and (-) on the battery / rechargeable battery and the product.
■ Use a dry lint-free cloth or cotton swab to clean the contacts on the battery / rechargeable battery and in the battery compartment before inserting!
■ Remove exhausted batteries / rechargeable batteries from the product immediately.

- Before initial use

Note: Remove all packaging materials from the product.

- Inserting the batteries (Figure C)

Note: The batteries 21 are already inserted when delivered.

□ Remove the insulating tape 24.

- Attaching the repair device

☐ Insert the ball joint of the repair device 15 into the corresponding recess of the fixing clamp 11.

☐ Fix the repair device 15 in place by tightening the fastening screw 16 clockwise.

☐ Tightening the retaining screws 17 in clockwise direction for holding the supporting rod 22 properly.

☐ Turn the locking screws 23 tightly for fixing the Alligator clips 18 properly.

☐ Push the fixing clamp 11 onto the mounting rod 10, set the desired height and tighten the fastening screw 12 clockwise.

- Mounting the magnifying glass

☐ Insert the ball joint 5 into the corresponding recess and tighten the fastening screw 6 for the ball joint 5 clockwise (Fig. A).

☐ Push the fixing clamp 7 on to the mounting rod 10 and set the desired height. Tighten the fastening screw 8 by turning it clockwise.

- Placement of the base (Figure D)

☐ The soldering iron holder could be installed on either right or left side on base 14 with screwdriver (not included) as an option for left or right-handed user.

The soldering iron holder should be adjusted the correct position to rear side of the base 14 as shown in Figure D in order to prevent restriction on use of the precision engineer's LED magnifying glass 1, fixing clamp 11 and alligator clips 18.

- Mount the base plate (Figure E)

Screw the base plate to the base 14 using the screws 26 provided, as shown in Figure E. Use a suitable screw-driver (not included).

Use

• Using the product

Turn the retaining screws on the alligator clips 18 in a clockwise direction. Clamp the item to be repaired with the alligator clips 18 in the repair device 15.

Note: Pay attention to a balanced weight distribution for better stability of the product.

☐ Move the On / Off switch 9 into position "ON" to switch on the LEDs 20.
Note: The LED bulbs 20 are non-replaceable.
Point the precision engineer's LED magnifying glass with the LED lamps 20 at the clamped work piece.
☐ Release the alligator clips in order to remove the work piece.
☐ Move the On / Off switch 9 into position "OFF" to switch off the LEDs 20.

- Changing the batteries

☐ Remove the battery compartment cover 3 from the battery compartment 4 by using a suitable screwdriver (not included).
□ Remove the old batteries.
Place the new batteries 21 of type 1.5 V=±R1130 into the battery compartment 4.

Note: Ensure the correct polarity. This is shown in the battery compartment 4.

☐ Place the battery compartment cover 3 back on the battery compartment 4.
☐ Use a suitable screwdriver (not included) to screw on the battery compartment cover 3.

- Troubleshooting

● = Problem

● = Cause

O = Solution

● The LED lamps 20 do not light up.

The batteries 21 are flat.

○ Replace the used batteries 21 with new ones (see: "Changing the batteries").

The batteries 21 have been inserted incorrectly.

Check the correct polarity of the batteries [21] (see: "Inserting the batteries").

● Cleaning and maintenance

CAUTION! Clean the precision engineer's LED magnifying glass 1 very carefully in order to avoid scratches.

Do not use corrosive or abrasive cleaners under any circumstances.

Use a cleaning cloth for cleaning the product. Moisten it a little if necessary.

☐ Use a dry, fluff-free cloth for cleaning the lens.

□ Never immerse the product in water or other liquids under any circumstances.

If you are not using the product, store it in such a way that the precision engineer's LED magnifying glass 1 is not scratched. Wrap the product in a soft cloth.

●Disposal

The packaging is made entirely of recyclable materials, which you may dispose of at local recycling facilities.

Observe the marking of the packaging materials for waste separation, which are marked with abbreviations (a) and numbers (b) with following meaning: 1–7: plastics / 20–22: paper and fibreboard / 80–98: composite materials.

The product and packaging materials are recyclable, dispose of it separately for better waste treatment. The Triman logo is valid in France only.

Contact your local refuse disposal authority for more details of how to dispose of your worn-out product.

To help protect the environment, please dispose of the product properly when it has reached the end of its useful life and not in the household waste. Information on collection points and their opening hours can be obtained from your local authority.

Faulty or used batteries / rechargeable batteries must be recycled in accordance with Directive 2006/66/EC and its amendments. Please return the batteries / rechargeable batteries and / or the product to the available collection points.

Environmental damage through incorrect disposal of the batteries / rechargeable batteries!

Batteries / rechargeable batteries may not be disposed of with the usual domestic waste. They may contain toxic heavy metals and are subject to hazardous waste treatment rules and regulations. The chemical symbols for heavy metals are as follows: Cd = cadmium, Hg = mercury, Pb = lead. That is why you should dispose of used batteries / rechargeable batteries at a local collection point.

Service

Service Great Britain

Tel.: [phone]

E-Mail: [e-mail]

Az alkalmazott

Symbolic illustration of a sun shining over a microscope, enclosed in a circle with a diagonal line crossing through (no text or labels)

NOSTE OCHRANNÉ RUKAVICE! Vyte-

Symbol of two gloves inside a black circle (no text or numbers)

● = Problem
= Ursache
O = Lösung