PIPI-411 - Paint gun Truper - Free user manual and instructions
Find the device manual for free PIPI-411 Truper in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Paint Spray Gun |
| Brand | Truper |
| Model | PIPI-411 |
| Application | Automotive, woodworking, DIY projects |
| Power Source | Pneumatic (requires air compressor) |
| Recommended Air Pressure | 40-60 psi (2.8-4.1 bar) |
| Air Consumption | 8-12 cfm at 50 psi |
| Fluid Nozzle Sizes | 1.4 mm, 1.8 mm, 2.0 mm (interchangeable) |
| Paint Cup Capacity | 600 ml (20 oz) gravity-feed |
| Pattern Control | Adjustable round, vertical, horizontal, and fan width |
| Fluid Flow Control | Stepless adjustment screw |
| Weight | 1.1 kg (2.4 lbs) |
| Dimensions (L x W x H) | 180 x 120 x 250 mm (7.1 x 4.7 x 9.8 in) |
| Construction Material | Aluminum body, brass nozzle, stainless steel needle |
| Compatible Paints | Latex, acrylic, enamel, lacquer, primer |
| Cleaning | Disassemble and clean with solvent after each use |
| Safety Features | Air inlet filter, trigger lock, pressure relief valve |
| Spare Parts Available | Nozzle sets, needles, air caps, gaskets |
| Repairability | User-serviceable; replacement parts sold separately |
| Warranty | 1 year limited warranty |
Frequently Asked Questions - PIPI-411 Truper
What is the recommended air pressure for the Truper PIPI-411 paint gun?
The recommended air pressure range is 40-60 psi (2.8-4.1 bar). Using lower pressure may cause poor atomization, while higher pressure can create overspray.
How do I clean the paint gun after use?
Disassemble the gun by removing the nozzle, needle, and air cap. Rinse all parts with paint thinner or water depending on paint type. Use a soft brush to remove dried residue. Reassemble after drying.
What type of paint can I use with the PIPI-411?
You can use latex, acrylic, enamel, lacquer, and primer. Always thin paint to the manufacturer's recommended viscosity for spray application.
Why is my paint gun spitting or splattering?
Spitting is usually caused by clogged nozzle, low air pressure, or thick paint. Clean the nozzle, increase pressure, or thin the paint accordingly.
How do I adjust the spray pattern?
Use the pattern control valve located on the air cap. Rotate to select round, vertical, horizontal, or fan patterns. Adjust fluid flow with the screw on the trigger side for desired width.
What is the capacity of the paint cup?
The gravity-feed cup holds 600 ml (20 oz) of paint.
Can I use the PIPI-411 with a small air compressor?
Yes, but your compressor must deliver at least 8 cfm at 50 psi. A small hobby compressor may not sustain continuous operation. Check the compressor's duty cycle.
How do I replace the nozzle or needle?
Unscrew the retaining ring to remove the old nozzle. Pull out the needle from the rear. Insert new parts in reverse order. Ensure proper alignment before tightening.
Is the Truper PIPI-411 suitable for painting cars?
Yes, it is suitable for automotive painting with thinned enamel or urethane paints. Use a 1.4 mm nozzle for base coats and 1.8 mm for primers.
What maintenance does the gun require?
Clean after every use, lubricate moving parts with light oil, and inspect seals for wear. Replace gaskets if air leakage occurs. Store in a dry, dust-free place.
User questions about PIPI-411 Truper
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Paint gun in PDF format for free! Find your manual PIPI-411 - Truper and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. PIPI-411 by Truper.