IAN 78790 - Motorcycle helmet CRIVIT - Free user manual and instructions

Product Type	Flip-Up Motorcycle Helmet
Homologation	ECE-R 22.05
Certifications	TÜV Wearing Comfort, Toxproof
Outer Shell Material	High-quality ABS plastic (HCM Technology)
Visor	Anti-fog, anti-scratch coating; replacement visor type DS-MULTIX301
Sun Shield	Integrated, operated by slider with safety latch; for daytime use only
Ventilation	Top vent, front vent, breath deflector, air exhaust
Inner Lining	Removable, washable, with Coolmax inserts for moisture management
Cheek Pads	Two pairs included for individual size adjustment (thin pre-installed, thick separate)
Acoustic Damping	Yes, removable pads for noise reduction
Chin Piece	Flip-up, with pivoted release (9) and audible lock
Retention System	Snap-fastener chin strap with adjustable length
Winter Collar	Included, replaceable with standard collar
Sizes Available	S (55-56 cm), M (57-58 cm), L (59-60 cm), XL (61 cm)
Scope of Delivery	Helmet, additional cheek pads, replacement visor, acoustic damping, winter collar, helmet bag, instruction manual
Care Instructions	Hand wash lining at 30°C; clean shell with water and pH-balanced soap; visor with soap and water only
Warranty	3 years from date of purchase
Glasses Wearer Compatibility	Yes, with extra soft padding for comfort
Anti-Microbial Treatment	HeiQ Pure dynamiq for odor control and thermal regulation

Frequently Asked Questions - IAN 78790 CRIVIT

How do I select the correct helmet size?

Measure your head circumference with a flexible tape measure. Refer to the size table: S (55-56 cm), M (57-58 cm), L (59-60 cm), XL (61 cm). Try on different sizes; the helmet should fit snugly without moving when the chin strap is unfastened. The skin of your temples should move with the helmet.

How should I clean the visor?

Use only soap and water. Avoid solvents, petrol, or abrasive detergents. Wipe gently with a soft cloth and allow to air-dry. Never expose the visor to heat sources.

How do I replace the visor?

Slide the visor to the highest (fully opened) position. Pull the red visor-locking lever and remove the visor. To insert the new visor (type DS-MULTIX301), place it in the fully opened position, pull the lever, and snap it into place.

How do I use the sun shield?

The integrated sun shield (8) is operated using the slider (4) after pressing the safety latch. Use only during daylight and when the visor is closed. Never use at night or in low visibility.

Can I remove and wash the inner lining?

Yes, the inner lining (13) is removable. Remove the collar and cheek pads first, then undo the back press-studs and pull the clips from the front. Hand wash the lining below 30°C and air-dry at room temperature. Avoid heat.

Is this helmet suitable for glasses wearers?

Yes, the helmet features extra soft padding in the temple area to improve comfort for glasses wearers.

What safety certifications does the helmet have?

The helmet is ECE-R 22.05 homologated, TÜV-certified for wearing comfort, and carries the Toxproof mark for absence of harmful substances.

How should I store the helmet?

Store in a dry, well-ventilated place at room temperature. Avoid heat sources and direct sunlight. Do not hang the helmet on the motorcycle or expose it to exhaust pipes.

What is the warranty period?

The helmet comes with a 3-year warranty from the date of purchase covering material and workmanship defects. It does not cover normal wear or misuse. Retain your receipt.

Can I use a tinted visor at night?

No, never use smoked or tinted visors at night or in poor visibility. They reduce visibility and increase accident risk. Use only during the day.

USER MANUAL IAN 78790 CRIVIT

Exterior view of a silver and silver Iidl-Service helmet (no signage)

FLIP-UP HELMET

GB

Flip-Up Helmet

Instructions for use

DE AT CH

Klapphelm

Bedienungsanleitung

G

Before reading, fold out the illustration page and get to know all of the functions of your unit.

DE AT CH

GB Instructions for use 5

Medical illustration showing a cross-sectional view of a skull with an arrow indicating direction (no text or labels)

GB Instructions for use

Parts Overview 6

Scope of Delivery 6

Important Information 6

Instructions for Use

Safety Advice 6-7

Product Characteristics....7-8

Use and Installation Instructions

Inner Lining 9

Chin-Wind Deflector....9

Snap-Fastener System 9

Sun Shield....9

Cheek Pads 9

Acoustic Damping 9

Front Vent 9

Top Vent 9

Winter Collar 10

Visor Replacement 10

Selecting the correct helmet size.... 10

Maintenance and Care....10 - 11

Storage 11

Disposal Instructions 11

3 Years Warranty 11

Congratulations!

With your purchase you have decided on a high-quality product. Get to know the product before you start to use it. Carefully read the following operating instructions. Use the product only as described and only for the given areas of application. Keep these instructions safe. When passing the product on to a third party, always make sure that the documentation is included.

Parts Overview

1 Top vent
2 Air exhaust
3 Visor mechanism
4 Slider for sun shield with safety latch
5 Front vent
6 Breath deflector
7 Visor
8 Sun shield
9 Pivoted release
10 Chin-wind deflector
11 Acoustic damping
12 Cheek pads
13 Inner Lining
14 Standard collar
15 Winter collar
16 Chin straps with snap fastener

Scope of Delivery

The scope of delivery for your helmet consists of the following:

• Additional pair of cheek pads for individual size adjustment
- Replacement visor
- Acoustic damping
- Winter collar
- Helmet bag
- Instruction manual

Important Information

Our helmets are manufactured in accordance with the latest technology and are specifically designed for motorcycling. Whether the owner deems them to be suitable for any other use, is up to him. Wearing a helmet does not exclude the possibility of injury should an accident occur.

To guarantee adequate protection this helmet must be well fitting and securely fastened. Every helmet that is exposed to a hard blow must be replaced.

We guarantee that this item is free of production and material defects. The guarantee does not apply to normal wear and tear and in case of improper use.

Instructions for Use

Safety Advice

- Warning!

The helmet is equipped with a hinged sun visor, which may only be used in conjunction with a closed visor.

• To open the chin piece, press the release (9) and lift the chin piece up (see Fig. A).
• To close the chin part, pull the chin section down until it audibly locks into place.
• The retention system must always be carefully set and locked.

- Always ensure that there is no airflow restriction inside the helmet.

- Ensure that your visor is clean and scratch-free at all times. Never use smoked visors at night or when visibility is poor. Exchange damaged visors for a genuine replacement immediately. Your safety is at risk.

You are able to obtain replacement visors from the stipulated service address for a period of 5 years from the purchase date.

Visor type: DS-MULTIX301

• Never make any changes to any part of your helmet. Do not make any alterations to the outer shell, do not insert screws.

• The helmet may not be painted or have stickers or labels.

• The helmet is designed to absorb the energy of a blow or a collision by destroying some of its components. In case of a further blow it wouldn't protect you any longer. After an accident, the helmet must be replaced even though it doesn't show external damages.

• Refrain from transporting your helmet by hanging it onto any part of your motorcycle. Keep it away from exhaust pipes and other sources of heat.
• Never use solvents, petrol or other detergents when cleaning the shell and interior of your helmet. Only use water and pH balanced soap. The padding can be cleaned using soap and a small brush. The visor should be cleaned with soap and water only, leave it to air-dry. Do not expose the visor to any source of heat!
• Only use genuine spare parts for your helmet.
• Only use the sun shield and tinted visor in daylight! Never use in twilight or at night.

Product Characteristics

ECE-R 22.05 Homologation

This helmet is in compliance with ECE-R 22.05 standards and is homologised accordingly. The ECE-R 22.05 standard consists of uniform conditions for the approval of protective

helmets and its visors for drivers and passengers of motorcycles and mopeds. The basic principles for these tests are the so called ECE-Regulations of the Economic Commission for Europe.

Significant Tests of the ECE-Regulation 22.05

• Shock absorbance
  • Dynamic test of wear features
• Field of vision test
• Design strength
  • Sustainability test (Strip-off test)
• Chin straps and lock test
  • Shear test for outside edges
• Visor test (mechanical and visual characteristics)
• Chin bar, chin part damping test

- Friction performance test of the outer shell

TÜV certified wearing comfort

The TÜV Rhineland evaluates performance and comfort of helmets by means of test subjects. Only helmets that meet these stringent requirements are awarded the desired logo.

Aspects such as aerodynamics, acoustics, ventilation, comfort and fit are rated.

Toxproof

The Toxproof-sign of the Technical Inspection Authority (TÜV) Rhineland identifies products

that have been tested for toxic substances where no health hazards can be expected according to the perception of today.

Inside Padding with Coolmax® Inserts

Coolmax ^® by INVISTA is a high-performance fabric fibre

that supports its wearers during sport activities. Based on the patented DuPont-fibre technology, Coolmax ^® transports moisture from the body to the fabric surface where it dries quicker than with any other fabric.

The specially developed fibres of INVISTA that are used for Coolmax ^® -fabrics transport the moisture away from the body to the surface of the fabric where it has the opportunity to evaporate quickly. At the same time, the uniquely formed fibres offer maximum breathing activity, even in wet conditions. In addition, the breathing activity improves the heat regulating effect.

Cheeks, forehead and neck pads of this article are equipped with Coolmax ^® .

HeiQ® Pure dynamiq

PURE Textile freshness

Experience the feeling of lasting freshness through the power of silver, keeping you odour-free all day lang.

ADAPTIVE Thermal control

Feel good all over. The textile will cool you down when you're hot, and keep you dry longer in cold weather. Cools and minimises perspiration.

Anti-Fog

The visor and the sun shade feature an anti-fog coating.

The anti-fog coating is the result of a special surface treatment that is used for motorcy-

cle visors among other things. This special coating prevents that the visor fogs up quickly with breathable air. For these products this increases user safety.

Anti-Scratch

To reduce the risk of scratching, the built-in visor and the replacement visor feature a special coating. This coating prevents rapid scratching of the external part of the visor.

Breath deflector and visor ventilation

The breath deflector (6) decreases fogging of the visor due to exhaled air. Additionally, the air circulation in the visor area is improved.

Construction for those who wear glasses

The helmet is also suitable for those who wear glasses. An extra soft padding improves the wearing comfort for those who wear glasses.

HCM Technology

High Density Copolymer Matrix: High quality ABS

plastic is formed under extreme heat and pressure to make a robust and impact-resistant outer shell.

Use and Installation Instructions

Inner Lining

The inner lining (13) can be completely removed and cleaned separately (see care instructions).

To remove the inner lining, firstly remove the helmet collar and the cheek pads. Then undo the back press-studs of the inner lining and pull the clips of the inner lining from the front side of the helmet (see Fig. C).

Chin-Wind Deflector

The chin-wind deflector (10) is secured to the pivoted piece by means of snaps.

This can be removed and re-attached as required (see Fig. E).

Snap-Fastener System

The snap-fastener enables an individual and quick vernier adjustment of the chin strap.

Press the snap-fastener together until the helmet is sitting comfortably but firm (see Fig. D).

By means of the snap at the end of the chinstrap, the excess chinstrap can be attached to additionally secure it.

Sun Shield

The integrated sun shield (8) will enable you to quickly and easily react to changed light conditions with the aid of the patent mechanism.

To pull out and retract the sun shield, press the safety latch to operate the slider (4) (see Fig. B).

Note:

• Please take care that the edge of the sun shield does not block your field of vision.
• The sun shield may only be used when the visor is closed and may only be used during the day.

Cheek Pads

You will receive two different pairs of cheek pads (12) for individual size adjustment.

The thinner cheek-pads are already pre-mounted as standard. The thicker cheek pad is enclosed with the helmet separately.

If the helmet is too loose and therefore is not sitting firmly on your head, you can replace the thin cheek pad with the thicker ones.

The cheek pads are affixed via three press-studs respectively in the helmet. You can easily remove the pads (see Fig. F). The thicker cheek pads can now also be affixed in the helmet with three press-studs. You need to be able to hear that each press-stud locks-in.

Acoustic Damping

The acoustic damping (11) is for noise reduction, in particular when driving at high speeds.

Press the acoustic damping into the cavity of the cheek pads (see Fig. G). The acoustic side pad equipped with Velcro faces towards the helmet shell.

Front Vent

The front vent (5) can be opened and closed by means of a slider (see Fig. H).

Top Vent

The top vent (1) can be opened and closed by means of a slider (see Fig. 1).

Winter Collar

To reduce the wind inlet at the bottom of the helmet during periods with very cold temperatures, the pre-installed standard collar (14) can be replaced with the supplied winter collar (15).

Removing the standard collar

Pull the one-piece standard collar out of the helmet (see Fig. J).

Inserting the Winter Collar

First attach the plastic clip in the centre at the back part of the helmet in the groove between the outer shell and the padding.

Once the plastic clip is completely locked, press the complete winter collar again firmly onto the padding of the helmet (see Fig. K).

Visor Replacement

If the pre-mounted visor (7) is damaged or severely scratched, you can exchange it with the replacement visor.

Removal of the Visor

• Slide the visor into the highest position (fully opened) (see Fig. L).
• Pull the red visor-locking lever and remove the visor (see Fig. M).

Inserting the Visor

• Place the replacement helmet on the hold-down device and observe the correct positioning in the process (fully opened) (see Fig. L).
• Pull the red visor-locking lever and place the visor appropriately (see Fig. N).
• Allow the replacement visor to snap in and close the visor.

Selecting the correct helmet size

• Choose your helmet by measuring the circumference of your head with a flexible tape measure. Always try on a couple of different sizes before buying a close fitting helmet. When wearing the helmet, the skin of your temples should ideally move with it.
• Make sure that the helmet does not move around when the retention system is open.
• The retention system must be set securely. The

chinstrap must sit comfortably under the chin as far back towards the neck as possible. Fasten it as tight as possible. The right degree of tension is reached once you find it difficult to insert your finger between the chinstrap and neck, yet finding it easy to breath and swallow. Make sure that the helmet sits securely once the retention system is on. Make sure that the helmet does not restrict your movements, e.g. when turning your head to look behind you.

- Make sure the helmet carries a sticker certifying homologation.

Size table
Size Head circumference
S 55 - 56 cm
M 57 - 58 cm
L 59 - 60 cm
XL 61 cm

Maintenance and Care

Regular maintenance and care contributes to safety and maintaining the helmet.

Cleaning of the Helmet

• Never use solvents, petrol or other detergents when cleaning the shell and interior of your helmet.
• Only use water and pH balanced soap.

Visor care and cleaning

• After using the helmet, lightly wipe off any grime (e.g. dead insects, dirt, sand, dust etc) from the visor with a soft cloth and then fully wipe it clean using a dry soft cloth.
• When the visor gets wet (e.g. rainwater) it should always be wiped with a soft cloth.

- When cleaning the visor, never use any petroleum-based solvents or detergents containing abrasives.

Cleaning of the Cheek Pads, Acoustic Pads and Inside Pads

• Hand wash below 30 °C.
• Allow to dry at room temperature.
• Avoid sources of heat.
• When not in use, store in a dry, well ventilated place.

Storage

When not in use, store the helmet in a dry and well ventilated place at room temperature. Avoid sources of heat. Do not needlessly expose the item to heat, e.g. in the car in hot outside temperatures.

Disposal Instructions

Dispose of the product and all its components through a licensed disposal company or your municipal disposal facilities. Please observe the current regulations. If in doubt, consult your disposal facility about an environmentally friendly disposal.

3 Years Warranty

The product was produced with great care and under constant supervision. You receive a three-year warranty for this product from the date of purchase. Please retain your receipt.

The warranty applies only to material and workmanship and does not apply to misuse or improper handling. Your statutory rights, especially the warranty rights, are not affected by this warranty.

With regard to complaints, please contact the following service hotline or contact us by e-mail. Our service employees will advise as to the subsequent procedure as quickly as possible. We will be personally available to discuss the situation with you.

Any repairs under the warranty, statutory guarantees or through goodwill do not extend the warranty period. This also applies to replaced and repaired parts.

Repairs after the warranty are subject to a charge.

Size S IAN: 78787

Size M IAN: 78788

Size L IAN: 78789

Size XL IAN: 78790

GB Service Great Britain

Tel.: [phone] (£ 0.10/Min.)

E-Mail: [e-mail]