UPM 120 A1 - Polisher ULTIMATE SPEED - Free user manual and instructions
Find the device manual for free UPM 120 A1 ULTIMATE SPEED in PDF.
| Product Type | Polisher |
| Brand | Ultimate Speed |
| Model | UPM 120 A1 |
| Power Input | 120 W |
| Rated Voltage | 230-240 V~, 50 Hz |
| Idle Speed | 3500 min⁻¹ |
| Weight | ca. 2.3 kg |
| Protection Class | II |
| Protection Category | IP20 |
| Sound Pressure Level (LpA) | 61.7 dB(A); K=3 dB |
| Sound Power Level (LWA, measured) | 72.7 dB(A); K=3 dB |
| Sound Power Level (guaranteed) | 76 dB(A) |
| Vibration Emission (ah) | 17.543 m/s²; K=1.5 m/s² |
| Intended Use | Waxing, polishing, and dewaxing of vehicle varnish |
| Included Accessories | 2 towelling covers, 2 synthetic fur covers, instruction manual |
| Safety Class | II (double insulated) |
| Guarantee Period | 3 years |
| Service Contact (UK) | Tel: 0871 5000 720, Email: grizzly@lidl.co.uk |
| Service Contact (Ireland) | Tel: 1890 930 034, Email: grizzly@lidl.ie |
| Service Contact (Cyprus) | Tel: 8009 4409, Email: grizzly@lidl.com.cy |
| Spare Parts | Available at www.grizzly-service.eu |
Frequently Asked Questions - UPM 120 A1 ULTIMATE SPEED
User questions about UPM 120 A1 ULTIMATE SPEED
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Polisher in PDF format for free! Find your manual UPM 120 A1 - ULTIMATE SPEED and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. UPM 120 A1 by ULTIMATE SPEED.
USER MANUAL UPM 120 A1 ULTIMATE SPEED
ELECTRIC POLISHER UPM 120 A1
GB IE NI CY
ELECTROPOLISHER
Translation of the original instructions
DE AT CH
POLIERMASCHINE
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the device.
GR CY
Intended purpose......4
General description......4
Extent of the delivery ....4
Functional description......5
Overview....5
Technical specifications......5
Notes on safety......5
Symbols and icons 5
General Safety Directions
for Power Tools 6
Operation 8
Tighten cover on the polishing disc.....8
Switching on and off 8
Waxing/polishing paint surfaces .....8
Dewaxing/polishing paint surfaces ....9
Cleaning and maintenance......9
Cleaning....9
Storage....9
Waste disposal and environmental
protection 9
Replacement parts / Accessories 10
Guarantee 10
Repair Service....11
Service-Center....11
Importer 11
Translation of the original
EC declaration of conformity .....33
Introduction
Congratulations on the purchase of your new device. With it, you have chosen a high quality product.
During production, this equipment has been checked for quality and subjected to a final inspection. The functionality of your equipment is therefore guaranteed.
The operating instructions constitute part of this product. They contain important information on safety, use and disposal. Before using the product, familiarise yourself with all of the operating and safety instructions. Use the product only as described and for the applications specified. Keep this manual safely and in the event that the product is passed on, hand over all documents to the third party.
Intended purpose
The device is designed for waxing and polishing or dewaxing of vehicle varnish.
The device is intended to be used by do-it-yourselfers. It was not designed for heavy commercial use.
The tool is to be used by adults. Children over the age of 16 may not use the tool except under supervision.
The manufacturer is not liable for damages caused by an improper use or incorrect operation of this device.
General description
See the front fold-out page for illustrations.
Extent of the delivery
Carefully unpack the appliance and check that it is complete. Dispose of the packaging material correctly.
- Appliance
- 2 Towelling covers
- 2 Synthetic fur covers
- Instruction manual
Functional description
The device is designed for waxing and polishing or dewaxing of vehicle varnish. Rotating the polishing disc helps achieve a consistent mode of operation. The polishing bonnets can be exchange for different applications and detachable for cleaning.
Overview
1 Handle
2 ON / OFF switch
3 Polishing disc
4 2 Synthetic fur covers
5 2 Towelling covers
6 Mains cable
Technical specifications
Polishing machine.....UPM 120 A1
Rated input voltage (U). 230-240 V\~, 50 Hz
Power input (P).... 120 W
Idling speed ( n_0 )....3500 min ^-1
Safety class ....
Protection category.... IP 20
Weight ...... ca. 2.3 kg
Sound pressure
level (L pA )......61.7 dB(A); K pA = 3 dB
Sound power level ( L_WA )
measured.....72.7 dB(A); K_WA = 3 dB
guaranteed 76 dB(A)
Vibration ( q_n ) ...17.543 m/s ^2 ; K= 1.5 m/s ^2
Levels of noise and vibration were determined according to the norms and regulations in the declaration of conformity.
The vibration emission value has been measured according to a standardised testing method and may be used for comparison with another electric tool.
The indicated vibration emission value may also be used for an introductory assessment of the exposure.
Warning: The vibration emission value whilst actually using the electrical tool may vary from the given values independently of the type and way in which the electric tool is used. Safety measures for the protection of the operator are to be determined that are based on an estimate of the actual exposure under the real operating conditions (for this, all parts of the operating cycle are to be taken into account, for example, times in which the electric tool is turned off, and those during which it is turned on but running without a load).
Notes on safety
Caution! When using power tools, observe the following basic safety measures for the prevention of electric shocks and the risk of injury and fire. Please read all these instructions before using this electric tool and please keep the safety instructions.
Symbols and icons
Symbols on the device:
Warning!
Read the manual!
Remove the plug from the mains. Immediately if the cable is damaged or cut.
Do not expose the unit to rain.
Wear eye protection
Wear breathing protection
Wear ear protection
GBIE NICY
Safety class II
Electrical machines do not belong with domestic waste
Symbols used in the instructions:
Hazard symbols with information on prevention of personal injury and property damage.
Precaution symbol (explanation of precaution instead of exclamation mark) with information on prevention of harm / damage.
Notice symbol with information on how to handle the device properly.
General Safety Directions for Power Tools
WARNING! READ ALL SAFETY DIRECTIONS AND INSTRUC-
TIONS. Omissions in the compliance with safety directions and instructions can cause electrical shock, fire and/or severe injuries.
Retain all safety directions and instructions for future use.
The term „power tool“ in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
Work area safety :
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of fl ammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
Electrical safety :
CAUTION! The following states how to avoid accidents and injuries due to electric shock:
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock
b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces
the risk of electric shock. Use a circuit breaker with a current limit of 30 mA or less.
- If the supply cord of this power tool is damaged, it must be replaced by a specially prepared cord available through the service organization.
Personal safety:
CAUTION! The following states how to avoid accidents and injuries:
a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention white operating power tools may result in serious personal injury.
b) Wear personal protective equipment and always wear safety goggles. Wearing personal protective equipment such as anti-slip safety shoes, safety helmet, respiratory protection or hearing protection can reduce the risk of injury.
c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your fi nger on the switch or energising power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.
- Warning! Touching or inhaling harmful or toxic dusts that may arise from grinding paint containing lead or certain metals represents a danger to you and people who are close by. Keep persons nearby away from the hazard area. Eyes should be protected from the foreign matter, which can be caused to fly during the various applications. Dust or breathing masks should fly later the dust that is created during operation. Wear hearing protection in addition. If you are exposed to loud noise for a long time, you may suffer hearing loss. Wear protective gloves in addition where appropriate.
Power tool use and care :
- Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
- Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
- Disconnect the plug from the power source and/or the battery pack from the power tool before ma-
king any adjust -ments, changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of starting the power tool accidentally.
- Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
- Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool's operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
- Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
- Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
Service:
- Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
Operation
Caution! Risk of injury!
ways remove the mains plug before working on the tool.
The mains cable is to run over the user's shoulder during the use of the polishing machine to avoid contact with the polished surface. This is to prevent scratches from the mains cable.
Tighten cover on the polishing disc
- Align the polishing disc (3) upwards.
- Using both hands, grab hold of a towelling cover (5) or a synthetic fur cover (4) and expand the elastic band outwards.
- Put the cover (4/5) on a part of the polishing disc (3) over the edge of the polishing disc. Pull the cover around the edge.
- Fit the cover (4/5) in centrally and tightly around the polishing disc (3).
Switching on and off
Make sure that the power supply voltage matches the voltage rating indicated on the device's type plate.
Connect the machine to the power supply.
- To switch on, tilt the on/off switch (2) to position „I“, the device turns on.
- To switch off, tilt the on/off switch (2) to position „0“, the device turns off.
- Firmly hold the device with both hands on the handle (1).
Waxing/polishing paint surfaces
- Use the towelling cover (5) to apply polish.
-
Apply the wax or polish on a slightly smaller area than the area you would like to polish.
-
Work with the polish in a crosswise movement or circular motions. Exert only moderate pressure on the surface.
- Please refer to the information from the polish manufacturer.
Do not allow the polish to dry out. There is a risk or surface damage. Therefore, do not work in direct sunlight or on a heated surface.
Dewaxing/polishing paint surfaces
- Use the synthetic fur cover (4) for dewaxing purposes.
- Work in a crosswise movement or circular motions. Exert only moderate pressure on the surface.
- Please refer to the information from the polish manufacturer.
Cleaning and maintenance
Pull the mains plug before any adjustments, maintenance or repair.
Have any work on the device that is not described in this instruction guide performed by a professional. Only use original parts. Allow the device to cool off before any maintenance or cleaning is undertaken. There is a risk of burning!
Always check the device before using it for obvious defi ciencies such as loose, worn or damaged parts, correct the positioning of screws or other parts. Examine the grinding disc in particular. Exchange the damaged parts.
Cleaning
Do not use any cleaning agent or solvent. Chemical substances can etch the plastic parts of the device. Never clean the device under running water.
- Thoroughly clean the device after every use.
- Clean the ventilation openings and the surface of the device with a soft brush or cloth.
- Hand wash to thoroughly clean the covers after each use. Only use a mild soap sud.
Storage
- Store the appliance in a dry place well out of reach of children.
Waste disposal and environmental protection
Be environmentally friendly. Return the tool, accessories and packaging to a recycling centre when you have finished with them.
Electrical machines do not belong with domestic waste.
- Hand over the device at an utilization location. The plastic and metal parts employed can be separated out and thus recycled use can be implemented. Ask our Service-Center for details.
- Defective units returned to us will be disposed of for free.
Replacement parts / Accessories
Spare parts and accessories can be obtained at www.grizzly-service.eu
If you do not have internet access, please contact the Service Centre via telephone (see "Service-Center" page 11). Please have the order number mentioned below ready.
Towelling covers 91103970
Synthetic fur covers 91103971
Polishing disc....91103974
Guarantee
Dear Customer,
This equipment is provided with a 3-year guarantee from the date of purchase. In case of defects, you have statutory rights against the seller of the product. These statutory rights are not restricted by our guarantee presented below.
Terms of Guarantee
The term of the guarantee begins on the date of purchase. Please retain the original receipt. This document is required as proof of purchase.
If a material or manufacturing defect occurs within three years of the date of purchase of this product, we will repair or replace – at our choice – the product for you free of charge. This guarantee requires the defective equipment and proof of purchase to be presented within the three-year period with a brief written description of what constitutes the defect and when it occurred.
If the defect is covered by our guarantee, you will receive either the repaired product or a new product. No new guarantee period begins on repair or replacement of the product.
Guarantee Period and Statutory Claims for Defects
The guarantee period is not extended by the guarantee service. This also applies for replaced or repaired parts. Any damages and defects already present at the time of purchase must be reported immediately after unpacking. Repairs arising after expiry of the guarantee period are chargeable.
Guarantee Cover
The equipment has been carefully produced in accordance with strict quality guidelines and conscientiously checked prior to delivery.
The guarantee applies for all material and manufacturing defects. This guarantee does not extend to cover product parts that are subject to normal wear and may therefore be considered as wearing parts (e.g. polishing disc, towelling covers or synthetic fur covers) or to cover damage to breakable parts (e.g. switches).
This guarantee shall be invalid if the product has been damaged, used incorrectly or not maintained. Precise adherence to all of the instructions specified in the operating manual is required for proper use of the product. Intended uses and actions against which the operating manual advises or
warns must be categorically avoided.
The product is designed only for private and not commercial use. The guarantee will be invalidated in case of misuse or improper handling, use of force, or interventions not undertaken by our authorised service branch.
Processing in Case of Guarantee
To ensure efficient handling of your query, please follow the directions below:
- Please have the receipt and item number (IAN 278948) ready as proof of purchase for all enquiries.
- Please find the item number on the rating plate.
- Should functional errors or other defects occur, please initially contact the service department specified below by telephone or by e-mail. You will then receive further information on the processing of your complaint.
- After consultation with our customer service, a product recorded as defective can be sent postage paid to the service address communicated to you, with the proof of purchase (receipt) and specification of what constitutes the defect and when it occurred. In order to avoid acceptance problems and additional costs, please be sure to use only the address communicated to you. Ensure that the consignment is not sent carriage forward or by bulky goods, express or other special freight. Please send the equipment inc. all accessories supplied at the time of purchase and ensure adequate, safe transport packaging.
Repair Service
For a charge, repairs not covered by the guarantee can be carried out by our service branch, which will be happy to issue a cost estimate for you. We can handle only equipment that has been sent with adequate packaging and postage.
Attention: Please send your equipment to our service branch in clean condition and with an indication of the defect.
Equipment sent carriage forward or by bulky goods, express or other special freight will not be accepted.
We will dispose of your defective devices free of charge when you send them to us.
Service-Center
GB Service Great Britain
Tel.: 0871 5000 720
(£ 0.10/Min.)
E-Mail: grizzly@lidl.co.uk
IAN 278948
IE Service Ireland Service Northern Ireland
Tel: 1890 930 034
(0,08 EUR/Min., (peak))
(0,06 EUR/Min., (off peak))
E-Mail: grizzly@lidl.ie
IAN 278948
CY Service Cyprus Tel: 8009 4409
E-Mail: grizzly@lidl.com.cy
IAN 278948
Importer
Please note that the following address is not a service address. Please initially contact the service centre specified above.
Service-Center....31
Importeur 31
  | Translation of the original EC declaration of conformity | |
| We hereby confi rm that the Polishing machine design series UPM 120 A1 Serial number 201701000001 - 201701048900 conforms with the following applicable relevant version of the EU guidelines: | ||
| 2006/42/EC • 2014/30/EU • 2011/65/EU* | ||
| In order to guarantee consistency, the following harmonised standards as well as national standards and stipulations have been applied: | ||
| EN 60745-1:2009/A11:2010 EN 60745-2-4:2009/A11:2011 EN 55014-1:2006/A2:2011 • EN 55014-2:2015 EN 61000-3-2:2014 • EN 61000-3-3:2013 | ||
| This declaration of conformity is issued under the sole responsibility of the manufacturer: | ||
 | Grizzly Tools GmbH & Co. KG Stockstädter Straße 20 63762 Großostheim Germany 27.01.2017 |  Volker Lappas Documentation Representative |
Translation of the original EC declaration of conformity
* The object of the declaration described above satisfies the provisions of Directive 2011/65/EU of the European Parliament and the Council of 8 June 2011 on limiting the use of certain harmful substances in electrical and electronic appliances.
