604-194 - Compressor Hamron - Free user manual and instructions

Type	Compressor (tyre inflator)
Power	300 W
Voltage	12 V DC
Working current	30 A
Maximum pressure	10.3 bar / 150 PSI
Cylinder diameter	2 × 30 mm
Recommended ON/OFF cycle	10 minutes on / 10 minutes off
Number of nozzles	5
Sound pressure level	72 dB(A), K=3 dB
Sound power level	92 dB(A), K=3 dB
Hose type	PVC air hose and rubber air hose
Power cord	12 V with battery clamps (red +, black -)
Gauge	Analogue pressure gauge
Carry case	Included (carrying handle on case)
Accessories	Ball needles (2), Presta valve, nozzle for air mattress, screw valve, quick connector
Safety equipment required	Safety goggles, hearing protection
Intended use	Car tyres, bicycle tyres, ATV tyres, sport equipment, air mattresses, beach toys
Cooling requirement	After 10 min continuous use, allow 10 min cool down
Storage	Store in carry case after use

Frequently Asked Questions - 604-194 Hamron

What is the maximum pressure of the Hamron 604-194 compressor?

The maximum pressure is 10.3 bar / 150 PSI.

How do I connect the compressor to a car battery?

Attach the red positive (+) clamp to the battery's plus terminal, then the black negative (-) clamp to the battery's negative terminal.

Can I run the compressor while the car engine is on?

Yes, for best performance and more efficient power supply, use with the car engine running. Ensure good ventilation and do not operate in confined spaces like a garage due to risk of suffocation.

How long can I operate the compressor continuously?

The recommended maximum continuous operation is 10 minutes, after which you must allow the compressor to cool for at least 10 minutes.

What types of objects can I inflate with this compressor?

It is designed for car tyres, bicycle tyres, ATV tyres, sport equipment, air mattresses, beach toys, and other inflatable objects.

What accessories are included with the compressor?

The package includes 5 nozzles: ball needles (2), Presta valve, nozzle for air mattress, and a screw valve connector with quick coupling.

How do I attach and detach the air hose?

To attach, pull back the sleeve of the quick connector, insert it into the valve, and push the sleeve forward until you hear a click. To detach, pull the sleeve back and remove.

What power source does the compressor require?

It requires a 12 V DC power source, typically a car battery. A fully charged battery is recommended for maximum performance.

Can I use the compressor in wet conditions?

No, do not use the compressor in moist or wet areas to avoid electric shock or damage.

How should I maintain and store the compressor?

Keep the compressor clean and store it in the carry case after use. Ensure all connectors are stored properly. Do not lift by the hose or cord.

USER MANUAL 604-194 Hamron

Black and yellow HAMRON air lift with coiled yellow hose and red clamp (no text or symbols visible)

SE Bruksanvisning för kompressor
NO Bruksanvisning for kompressor
PL Instrukcja obstugi kompresora
EN User instructions for compressor

SE - Bruksanvisning i original

NO - Bruksanvisning i original

EN - Operating instructions in original

Date of production: 2014-08-13

© Jula AB

SVENSKA....4

SÄKERHETSANVISNINGAR....4

TEKNISKA DATA....5

BESKRIVNING ....5

HANDHAVANDE 6

Fylla på luft 6

NORSK 9

SIKKERHETSANVISNINGER 9

TEKNISKE DATA 10

BESKRIVELSE....10

BRUK....11

Fyll på luft 11

POLSKI 14

ZASADY BEZPIECZEŃSTWA 14

DANE TECHNICZNE 15

OPIS 15

OBSŁUGA 16

SAFETY INSTRUCTIONS....19

TECHNICAL DATA 19

DESCRIPTION 20

OPERATION....20

Filling with air 21

SÄKERHETSANVISNINGAR

A. Bärväska

Symbol of a trash bin with diagonal lines crossing it, no text or labels present

Värna om miljön!

J. Strømbryter On/Off (På/Av)

BRUK

FYLL PÅ LUFT

MERK

Pure electrical circuit lines without any symbols

DBAJ O ŚRODOWISKO!

Read instructions before use.

Please retain for future reference.

WARNING!

• The safety instructions in this instruction manual do not cover all possible situations that can occur when the compressor is in operation. Always use common sense and pay attention to all warnings and safety information in the instruction manual.
• Make sure that you have read and understood all instructions. Failure to follow the following instructions could lead to an electric shock, fire and/or serious personal injury.
• Make sure that the work area is clean and properly lit. Cluttered surfaces and areas with poor lighting will increase the risk of personal injury or damage to property.
• This compressor is designed to fill car tyres, bicycle tyres, ATV tyres, sport equipment, air mattresses, beach toys and other inflatable objects with air. Do not use the air compressor for any other purpose as this may result in personal injury.
• This compressor should only be connected to 12 VDC. Do not attempt to connect the air compressor to any other power source or voltage. Do not change the cables or reconfigure the tyre inflator as this may result on personal injury.
• Do not operate the compressor in explosive environments, e.g. in the vicinity of flammable liquids or gases or dust. Power tools emit sparks, which can ignite the dust or vapours.
• Keep bystanders, children and visitors at a distance while operating the compressor.
• The compressor is not a toy. Keep children away from it.
• Use caution! After 10 minutes of continuous use, allow the compressor to cool for 10 minutes.
• Turn the power off when the compressor is not being used.
• Do not lift the compressor using the air hose or electrical cord as this may damage the product.
  • Always keep an eye on the compressor while it is in operation.
• Do not over inflate. Follow the manufacturer's instructions for the object being inflated.
• Do not use the compressor in moist or wet areas.
• Only use accessories that accompany the compressor.
• Wear safety goggles. Also wear a face or dust mask if the compressor is used in a moist environment.
  • Always use hearing protection.

TECHNICAL DATA

Voltage 12 VDC

Working current 30 A

Power 300 W

Maximum pressure 10.3 bar/150 PSI

Cylinder diameter 2 x 30 mm

Recommended ON/OFF cycle life 10/10 minutes

Number of nozzles 5 (x)

Sound pressure level, LpA 72 dB(A), K=3 dB

Guaranteed sound power level, LwA 92 dB(A), K=3 dB

DESCRIPTION

A. Carry case

F. PVC air hose

B. Analogue pressure gauge

G. Screw valve

C. Carrying handle

H. Ball needles (2), Presta valve, nozzle for air mattress

D. Rubber air hose

I. 12 V power cord with battery clamps

E. Quick connector

J. On/Off switch (On/Off)

OpERATION

FILLING WITH AIR

Note!

• A fully charged 12 V car battery is recommended for the compressor to achieve maximum performance. If the car battery is weak, the compressor will not achieve maximum effect.
• For the best results and a more efficient power supply, the compressor should be used with the car engine running. Please make sure this is done outdoors or in an open and well ventilated area, not in a confined space such as a garage as this can lead to life-threatening personal injuries and risk of suffocation. Always make sure there is good ventilation.
• Do not over inflate.

Car and bicycle tyres

1. Remove the direct drive compressor from its carry case.
2. Connect the PVC air hose to the compressor by moving the sleeve of the quick connector backwards and inserting it into the valve located at the end or the rubber air hose Push the sleeve in and move the quick coupling back until a click sound is heard; this means that the PVC air hose is correctly attached.
3. Connect the clamps of the 12 V power cable to the car battery by first attaching the red positive (+) clamp to the battery's plus terminal. Then attach the black negative (-) clamp to the battery's negative terminal.
4. Connect the screw valve connector to the tyre valve by turning clockwise until the attachment is securely in place.
5. Put the switch in the "On" position to start the compressor. Fill with the desired amount of air by checking the meter's PSI value. Place the switch in the "OFF" position when the desired air pressure is achieved.
6. Remove the air hose from the tyre valve by turning the screw valve connector anti-clockwise.
7. Remove the 12 V power cable clamps from the battery terminals.
8. Remove the PNC air hose from the compressor by moving the quick connector sleeve backwards and by removing it from the valve on the end of the rubber air hose.
9. Put the compressor back in the carry case. Store the compressor connectors in the carry case.

Balls, air mattresses, rubber boats etc.

1. Remove the direct drive compressor from its carry case.
2. Connect the PVC air hose to the compressor by moving the sleeve of the quick connector backwards and inserting it into the valve located at the end or the rubber air hose Push the sleeve in and move the quick coupling back until a click sound is heard; this means that the PVC air hose is correctly attached.
3. Connect the clamps of the 12 V power cable to the car battery by first attaching the red positive (+) clamp to the battery's plus terminal. Then attach the black negative (-) clamp to the battery's negative terminal.
4. Select an appropriate air filling accessory and screw it onto the end of the screw valve.
5. Insert the air filling accessory into the object being filled with air.
6. Put the switch in the "On" position to start the compressor. Fill with air until the desired pressure has been achieved and then place the switch in the "Off" position.
7. Remove the air filling accessory from the screw valve.
8. Remove the 12 V power cable from the car battery terminals.
9. Remove the PNC air hose from the compressor by moving the quick connector sleeve backwards and by removing it from the valve on the end of the rubber air hose.
10. Put the compressor back in the carry case. Store the compressor connectors in the carry case.

Jula reserves the right to make changes. In the event of problems, please contact our service department. www.jula.com

Symbol of a trash bin crossed with no text or labels, representing waste sorting or disposal (no text present)

Care for the environment!

Must not be discarded with household waste!

This product contains electrical or electronic components that should be recycled.

Leave the product for recycling at the designated station e.g. the clocal authority's recycling station.

CE

EC DECLARATION OF CONFORMITY EG FÖRSÄKRAN OM ÖVERENSSTÄMMELSE EF SAMSVARSERKLÆRING DEKLARACJA ZGODNOŚCI WE

Jula AB, Box 363, SE-532 24 SKARA, SWEDEN

RoHS Directive 2011/65/EU

These products were CE marked in year -14

Name and address of the person authorised to compile the technical file:

Viktoria Klaar Box 363, SE-532 37 Skara, Sweden

Skara 2014-08-04

Tobias Hammer PRODUCT MANAGER