IMETEC Ecoextreme Pro++ C2-100 - Vacuum Cleaner

Ecoextreme Pro++ C2-100 - Vacuum Cleaner IMETEC - Free user manual and instructions

Find the device manual for free Ecoextreme Pro++ C2-100 IMETEC in PDF.

📄 58 pages English EN Download 💬 AI Question 10 questions ⚙️ Specs
Notice IMETEC Ecoextreme Pro++ C2-100 - page 12
Pick your language and provide your email: we'll send you a specifically translated version.
Type of productBagless cylinder vacuum cleaner
BrandImetec
ModelEcoextreme Pro++ C2-100
Power sourceMains powered, 220-240 V ~ 50/60 Hz (typical)
Power ratingApprox. 700-900 W (typical for cylinder vacuums)
Dust collection systemCyclonic dust container, capacity approx. 1.5 L
Filter systemHEPA premotor filter + outlet filter (washable)
Suction controlElectronic power regulator on body + manual air flow slide on handle
Telescopic pipeYes, adjustable length with button
Combination brushYes, with toggle switch for hard floors/carpets
Accessories includedCrevice tool, multipurpose nozzle, dusting nozzle, parquet brush, Mini Animal Care Turbo Brush (Art. 8631 only)
Cord lengthApprox. 5-6 m (with yellow/red markings)
Automatic cord rewinderYes, with button
Parking positionsVertical and horizontal parking on appliance
Motor protectionThermostat automatic shut-off on overheating
Safety interlockPrevents closing dust container without pre-motor filter
WeightApprox. 4-5 kg
Warranty2 years

Frequently Asked Questions - Ecoextreme Pro++ C2-100 IMETEC

What should I do if the vacuum cleaner does not turn on?
Ensure the power cord is fully plugged into the socket and the ON/OFF switch is pressed. Check the power cord for damage; if damaged, contact an authorized service center.
The vacuum cleaner turns off during use and won't restart. What's wrong?
This is likely due to the motor protection thermostat activating because of overheating (e.g., clogged inlet or filters). Press the ON/OFF button, unplug, and let the appliance cool down for a few hours. Clean the dust container and filters before restarting.
How can I improve suction power?
First, check that the dust container is empty and filters are clean. Increase suction using the electronic power regulator on the body or close the manual air flow slide on the handle. Also ensure the brush is set correctly for the floor type.
How do I clean the HEPA premotor filter?
Remove the dust collection system by pressing the release button. Take out the HEPA filter and gently tap off dust. If very dirty, wash it with water and let it dry completely for at least 24 hours before reinserting. Replace if damaged.
Can I use the vacuum cleaner to pick up liquids?
No, this appliance is designed for dry vacuum cleaning only. Do not vacuum liquids, as it can damage the motor and void the warranty.
How do I use the Mini Animal Care Turbo Brush?
Attach it to the telescopic pipe or handle. It is designed for removing pet hair from upholstery, carpets, and hard floors. Do not use on animals or on carpets with fringes or pile longer than 15 mm. Do not hold it stationary while the roller spins.
The brush stays too close to the floor, making vacuuming difficult. What can I do?
Reduce the suction power by adjusting the electronic power regulator to a lower setting or by opening the manual air flow slide on the handle. This will lessen the brush's suction against the floor.
How do I replace the outlet filter?
Press the release/locking button of the outlet filter grid to remove it. Extract the old outlet filter. Insert a new or cleaned filter, then snap the grid back until it clicks. Ensure it is securely locked.
Why does the dust collection system not close properly?
The safety interlock prevents closing if the HEPA premotor filter is missing or incorrectly fitted. Make sure the filter is present and pushed in until the top appendix closes the safety interlock.
What is the warranty period and what does it cover?
The appliance has a 2-year warranty from the date of purchase. It covers manufacturing defects. The warranty does not cover damage from misuse, wear and tear, improper cleaning, or use of unauthorized accessories. Contact an authorized service center for repairs.

User questions about Ecoextreme Pro++ C2-100 IMETEC

0 question about this device. Answer the ones you know or ask your own.

Ask a new question about this device

The email remains private: it is only used to notify you if someone responds to your question.

No questions yet. Be the first to ask one.

Download the instructions for your Vacuum Cleaner in PDF format for free! Find your manual Ecoextreme Pro++ C2-100 - IMETEC and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. Ecoextreme Pro++ C2-100 by IMETEC.

USER MANUAL Ecoextreme Pro++ C2-100 IMETEC

Instructions for use

Dear customer, thank you for choosing our product. We feel certain you will appreciate its quality and reliability as it was designed and manufactured with customer satisfaction in mind. These instructions for use are compliant with the European Standard EN 82079.

IMETEC Ecoextreme Pro++ C2-100 - 1

WARNING! Instructions and warnings for safe use.

Before using this appliance, carefully read the instructions for use and in particular the safety notes and warnings, which must be complied with. Keep this manual together with its illustrative guide for future consultation. Should you transfer the appliance to another user, make sure you hand over this documentation as well.

NOTE: Should any part of this manual be difficult to understand or any doubt arise, contact the company at the address indicated on the last page before using the product.
NOTE: Persons with impaired vision may consult these instructions for use in digital format at the website www.tenactagroup.com

INDEX

Introduction....pag. 10

Safety notes....pag. 10

Symbols....pag. 12

Description of the appliance

and its accessories....pag. 12

Assembly....pag. 13

Accessories....pag. 13

Use....pag. 14

Cleaning and maintenance....pag. 15

Storing and caring for the product .....pag. 16

Troubleshooting....pag. 17

Disposal....pag. 17

Assistance and warranty ...... pag. 18

Illustrative guide....I-II-III

Technical data.....III

SAFETY NOTES

- After unpacking, make sure the appliance is intact, complete with all its parts as shown in the illustrative guide and with no sign of damage due to transportation. If in any doubt, do not use the appliance and contact an authorised service centre.

IMETEC Ecoextreme Pro++ C2-100 - SAFETY NOTES - 1

CAUTION! Remove any communication material such as labels, tags etc. from the appliance before use.

IMETEC Ecoextreme Pro++ C2-100 - SAFETY NOTES - 2

WARNING! Risk of suffocation.

Children shall not play with the packaging. Keep the plastic bag out of the reach of children.

- This appliance must be used only for the purpose for which it was designed, namely as a vacuum cleaner for home use. Any other use is considered not compliant with the intended use and therefore dangerous.

IMETEC Ecoextreme Pro++ C2-100 - SAFETY NOTES - 3

WARNING! Any misuse of the appliance may lead to injuries.

  • Before connecting the appliance to the mains supply, make sure that the voltage and frequency indicated on the technical data of the appliance correspond to those of the mains supply. The rating is on the appliance or on the power supply unit, if any (see illustrative guide).
  • This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
  • DO NOT use the appliance with wet hands, damp feet or barefoot.
  • DO NOT pull the supply cord or the appliance itself to remove the plug from the socket.
  • DO NOT pull or lift the appliance by the supply cord.
  • DO NOT expose the appliance to humidity, to the weather (rain, sun, etc.) or to extreme temperatures.
    • DO NOT leave the appliance unattended while in operation.
  • Always disconnect the appliance from the mains supply before cleaning or performing maintenance and when the appliance is not in use.

EN

  • If the appliance is faulty or malfunctions, switch it off and do not tamper with it. Contact an authorised technical service centre for any repairs.
  • If the supply cord is damaged it must be replaced by an authorised technical service centre, so as to prevent all risks.
  • This appliance shall not come into contact with water, other liquids, spray, steam. For any cleaning and maintenance operation refer to the instructions in the relevant chapter.
    • See the external packaging for the characteristics of the appliance.
  • Use the appliance only with the supplied accessories that are an essential part of the appliance.
  • DO NOT use the vacuum cleaner without inserting the dust bag, dust container or filter.
    • NOT direct the flexible hose, pipe or any other accessory towards eyes or ears and do not put them in your mouth when they are connected to the vacuum cleaner.
    • DO NOT use the appliance without the motor protection filter to prevent damaging the motor and the vacuum cleaner.

SYMBOLS

IMETEC Ecoextreme Pro++ C2-100 - EN - 1AttentionIMETEC Ecoextreme Pro++ C2-100 - EN - 2Prohibited
IMETEC Ecoextreme Pro++ C2-100 - EN - 3Note ON/OFF switchIMETEC Ecoextreme Pro++ C2-100 - EN - 4
IMETEC Ecoextreme Pro++ C2-100 - EN - 5Automatic cable winding Hard flooIMETEC Ecoextreme Pro++ C2-100 - EN - 6
IMETEC Ecoextreme Pro++ C2-100 - EN - 7Carpets and rugsIMETEC Ecoextreme Pro++ C2-100 - EN - 8Dust collection system release button

DESCRIPTION OF THE APPLIANCE AND ITS ACCESSORIES

Refer to Figure in the illustrative guide to verify your appliance equipment. All the figures are on the cover pages of these instructions for use.

  1. Handle
  2. Air flow manual adjustment device
  3. Telescopic suction pipe
    3A. Telescopic pipe adjustment button
    3B. Adjustable telescopic pipe
  4. Combination carpet/hard floors brush and similar
    4A. Brush position toggle switch
  5. Flexible suction pipe
  6. Flexible suction pipe locking buttons
  7. Electronic power regulator
  8. ON/OFF switch
  9. Dust collection system release button
  10. Carry handle
  11. Suction inlet
  12. Coupling for vertical parking position
  13. Technical data
  14. Power cable
  15. Automatic cable winding button

  16. Dust collection system
    16A. Upper cover
    16B. Upper cover opening/locking button
    16C. Safety interlock
    16D. HEPA premotor filter
    16E. Dust container

  17. Coupling for horizontal parking position
  18. Outlet filter
  19. Discharge filter grid
  20. Release/locking button of the outlet filter grid
  21. Accessories
    21A. Crevice tool
    21B. Multipurpose nozzle: To clean different surfaces
    21C. Dusting nozzle
    21D. Parquet brush
    21E. Mini Animal Care Turbo Brush (Only for Art.
    8631)

ASSEMBLY

  • Connect the flexible suction pipe (5) to the suction coupling (11) of the appliance rotating the base until the locking buttons of the flexible suction pipe click in their seat (6) indicating proper fastening. [Fig. B1].
  • Connect the handle (1) of the flexible pipe to the suction pipe (3).
  • Adjust the length of the telescopic pipe by pressing the adjustment button (3A) in the direction of the arrow and removing or retracting the adjustable telescopic pipe (3B) [Fig. C1].
  • Select the combination carpet/hard floors brush and similar (4) or the accessory (21) suited to the surface to be cleaned and connect the part to the telescopic pipe (3).

ACCESSORIES

Combination carpet/hard floors brush and similar (4)

Adjust the combination brush according to the type of flooring, using the brush position toggle switch (4A) [Fig. D1] to change from a ceramic floor position to a rugs and carpet position.

Your appliance is equipped with the following attachments:

Crevice tool (21A): To clean corners and crevices, such as radiators, skirting boards, blinds and awnings.

Multipurpose nozzle (21B): To clean sofas, armchairs, upholstered chairs and curtains.

Dusting nozzle (21C): To clean small objects, audio and TV appliances, computers and furniture.

Parquet brush (21D): Special brush to clean parquet floors.

Mini Animal Care Turbo Brush (21E - Only for Art. 8631): Specific for easily removing animal hairs from any surface. Suitable for the following surfaces: sofas, upholstery, ceramic, marble, carpets and rugs without fringes.

NOTE: ☑ DO NOT use the Mini Animal Care Turbo Brush on animals. ☑ DO NOT use the Mini Animal Care Turbo Brush on carpets with fringes, animal furs and rugs with a deep pile, longer than 15mm. Do not hold the brush still on the carpet while the roller is spinning.

IMETEC Ecoextreme Pro++ C2-100 - Your appliance is equipped with the following attachments: - 1

ATTENTION! Rotating parts in motion. Trapping hazard.

NOTE: The accessories can be connected to the suction telescopic pipe (3) or directly to the handle (1).

USE

Pull the power cable (14) completely up to the yellow mark, and insert the plug into the socket. The yellow mark on the cable is before the end part of the cable marked in red.

IMETEC Ecoextreme Pro++ C2-100 - USE - 1

WARNING! DO NOT use this appliance if there are visible signs of damage.

IMETEC Ecoextreme Pro++ C2-100 - USE - 2

WARNING! DO NOT use this applause to vacuum:

  • burning ashes, cigarette butts, etc.;
  • liquids, such as carpet cleaners;
  • sharp or hard objects, such as nails or large glass shards;
  • fine powder, such as cement;
  • toner powder (for laser printers, copy machines, etc.).

IMETEC Ecoextreme Pro++ C2-100 - USE - 3

CAUTION! DO NOT pull the supply cord beyond the red mark in order not to damage the appliance.

IMETEC Ecoextreme Pro++ C2-100 - USE - 4

WARNING! Unwind the supply cord completely to prevent hazardous overheating.

NOTE:A new appliance can develop odours the first few times it is used. These odours are harmless and disappear shortly afterwards. Ventilate the room.

  • Press the ON/OFF button (8) once to switch the vacuum cleaner on [Fig.F1].
  • Adjust the suction force by means of the electronic power regulator (7).
    Minimum: for curtains, fine and delicate fabrics.
    Average: for standard cleaning, sofas, armchairs, upholstered chairs, rugs and carpets.
    Maximum: for smooth floors.

- The suction power can also be changed by means of the manual adjusting device of the air flow (2) found on the handle (1) [Fig. E1].

Closed: Increases the suction power.

Open: Reduces the suction power.

  • Switch off the vacuum cleaner by pressing the ON/OFF button once (8) and unplug the power cord (14) from the power socket.
  • Press the automatic cord winding button (15) to wind the power cable [Fig.F1]. Hold the plug while winding the cable in order to prevent whiplash.

IMETEC Ecoextreme Pro++ C2-100 - USE - 5

ATTENTION! The vacuum cleaner has a motor protection thermostat, which intervenes in the case of overheating (caused by the inlet opening, filters, etc. being clogged). If it is triggered, press the ON/OFF (8) button to switch the appliance off and let it cool down completely for a few hours. Verify whether dust has clogged the filters or the inlet opening before restarting the appliance.

CLEANING AND MAINTENANCE

IMETEC Ecoextreme Pro++ C2-100 - CLEANING AND MAINTENANCE - 1

WARNING! Always disconnect the appliance from the mains supply before cleaning or performing maintenance.

IMETEC Ecoextreme Pro++ C2-100 - CLEANING AND MAINTENANCE - 2

CAUTION! Periodically verify that filters and the inlet opening are not clogged.

IMETEC Ecoextreme Pro++ C2-100 - CLEANING AND MAINTENANCE - 3

CAUTION! DO NOT use solvents or other aggressive or abrasive detergents in order not to damage the appliance surfaces.

IMETEC Ecoextreme Pro++ C2-100 - CLEANING AND MAINTENANCE - 4

CAUTION! Empty the dust container and clean the filters after every use in order not to damage the appliance.

IMETEC Ecoextreme Pro++ C2-100 - CLEANING AND MAINTENANCE - 5

WARNING! Let the filters dry completely after washing them for at least 24 hours before reassembly.

IMETEC Ecoextreme Pro++ C2-100 - CLEANING AND MAINTENANCE - 6

WARNING! Make sure all cleaned parts are completely dry before reusing the appliance.

CLEANING THE APPLIANCE

When necessary, clean the appliance with a damp cloth.

CLEANING THE COMBINATION CARPET/HARD FLOORS AND SIMILAR (4)

With the motor ON, rub the brush with your hand to remove the dust and fluff, which will be drawn.

CLEANING THE DUST COLLECTION SYSTEM (16)

EN

  • Clean the dust collection system following the instructions below, paying attention to the pictures in the illustrative guide.
  • Fit the dust collection system (16) back onto the vacuum cleaner ensuring the position lock clicks.

CLEANING THE DUST CONTAINER (16E)

  • Press the release button of the dust collection system (9) to extract the dust collection system (16) from the appliance [Fig.G1].
  • Press the upper cover opening/locking button (16B) to open the upper cover (16A) [Fig. G2].
  • Empty the container.
  • Fit the upper cover back on (16A) ensuring the couplings with the dust container (16E) are perfectly engaged and the upper cover opening/locking button (16B) is perfectly engaged as well.
  • Reinserire il sistema di raccolta polvere (16) sull'aspirapolvere avendo cura che scatti il blocco posizione.

CLEANING OR REPLACING THE PREMOTOR HEPA FILTER (16D)

  • Press the release button of the dust collection system (9) to extract the dust collection system (16) from the appliance [Fig. G1].
  • Remove the Hepa premotor filter (16D) from the dust collection system (16) [Fig. G3].
  • If the Hepa premotor filter (16D) is obstructed by dust, remove the dust taking care not to damage it.
  • If the filter is especially dirty, replace it with a new one.
  • Fit the HEPA premotor filter (16D) back onto the dust collection system (16) taking care to push the frame until the top appendix closes the safety interlock (16C).
  • Fit the dust collection system (16) onto the vacuum cleaner ensuring the position lock clicks.

CLEANING OR REPLACING THE OUTLET FILTER (16)

  • Press the release/locking button of the outlet filter grid (20) to remove the outlet filter grid (19).
  • Extract the outlet filter (18) [Fig. G4].
  • If the outlet filter (18) is obstructed by dust, remove the dust taking care not to damage it.
  • If the filter is especially dirty, replace it with a new one.
  • Refit the outlet filter (18) in the appliance [Fig. G4].
  • Fit the outlet filter grid back on (19) and click the coupling/locking button of the outlet filter grid in position (20).

STORING AND CARING FOR THE PRODUCT

The flexible suction pipe (5) can be disconnected from the appliance before putting it away. To this end, press the locking buttons of the flexible suction pipe (6) and disconnect the flexible suction pipe (5).

The suction pipe (3) with the combined brush (4) may be stored by hooking them to the appliance with the suitable couplings (12 or 17); the relative pictures in the illustrative guide are marked with the parking symbol [Fig. F2, F3].

TROUBLESHOOTING

PROBLEM SOLUTION
The appliance does not go on.·Ensure the power cord (14) is connected to the power socket.·Ensure the ON/OFF switch (8) has been pressed [Fig. F1].
The appliance turns off during use and does not turn on again.·The vacuum cleaner is equipped with a protective motor thermostat that shuts off the appliance in the event of overheating! (caused by obstructing objects or a clogged dust collection system).·In the event of tripping, press the ON/OFF switch , unplug the power cord (14) from the power socket and let the vacuum cleaner cool down completely.·Remove any dust or the obstructing object before restarting the appliance.
The vacuum cleaner does not suction well..·Power regulator at a minimum, raise the suction power.·The dust container (16E) is full: clean the container.·The filters are clogged: clean or replace the filters.
The dust collection system does not close correctly.·The safety interlock (16C) does not allow the dust collection system to be inserted (16) if the HEPA premotor filter (16D) is absent.·Make sure the HEPA premotor filter is present (16D) and it is fitted correctly.
The vacuum cleaner produces odours the first few times it is used.·These odours are harmless and disappear shortly afterwards. Ventilate the room.
The brush remains too close to the floor while vacuuming.·Decrease the suction power by acting on the electronic power regulator (7) or on the manual air flow regulation device (2).

DISPOSAL

IMETEC Ecoextreme Pro++ C2-100 - DISPOSAL - 1

The packaging of the appliance is made of recyclable materials. Dispose of it in accordance with the environmental protection regulations.

IMETEC Ecoextreme Pro++ C2-100 - DISPOSAL - 2

Pursuant to Directive 2012/19/EU on waste electrical and electronic equipment (WEEE), the crossed bin symbol on the appliance or its packaging indicates that the appliance must be disposed of separately from other waste at the end of its useful life. The user must therefore take the appliance to an appropriate recycling centre for electrical and electronic equipment. Alternatively, instead of handling the disposal, the user can hand over the appliance to the retailer when a new, equivalent one is purchased. The user can hand over electronic products measuring less than 25 cm to retailers of electronic products having a sales area of at least 400 m ^2 free of charge and with no obligation to buy. Appropriate separate collection for the subsequent procedure for the decommissioned appliance for recycling, which includes treatment and environmentally friendly disposal helps prevent adverse effects on the environment and health and promotes reusing and/or recycling materials that the appliance consists of.

ASSISTANCE AND WARRANTY

EN

The appliance is guaranteed for a period of 2 years from the date of purchase. Evidence shall be taken as the date indicated on the receipt/invoice (provided it is legible), unless the buyer can prove that the delivery occurred later. In the event of a defect in the product which existed prior to the date of delivery, appliance repair or replacement is guaranteed free of charge, unless one of the two solutions is disproportionate to the other. The buyer has the obligation to notify an authorised Service Centre of the non-conformity within two months from discovering the defect.

The warranty does not cover any part that may be defective due to:

a) Damage from transport or accidental drops
b) Incorrect installation or inadequate electrical system
c) Repairs or alterations made by unauthorised personnel
d) Poor or incorrect maintenance and cleaning
e) Product and/or product parts subject to wear and/or consumables
f) Failure to comply with the appliance's operating instructions, negligent or careless use,
g) vacuum materials that can damage the appliance (ex. Ashes, liquids, fine dust, toner...)
h) missed cleaning of the dust bin and the filter (for all models with cyclonic technology)
i) non substitution of a full dust bag and filters (for bagged models)
j) obstruction of the suction inlet
k) recharge of the battery not compliant to the instruction's chapter preparation/use (for products with batteries)
I) use of the appliance without the filters/dust bag
m) using the appliance without pulling out the cable completely (for appliances with cable winding)
n) winded, bent or damaged cable due to negligence.

The list above is purely indicative and not exhaustive and in any case, this warranty shall not cover all circumstances that cannot be attributed to manufacturing defects of the appliance. In addition, the warranty does not cover any case of improper use of the appliance and professional use.

All liability is disclaimed for any damage that may directly or indirectly be caused to persons, property and pets as a result of failure to comply with all the instructions provided in the “Instructions and Warnings Booklet” regarding appliance installation, use and maintenance.

This is without prejudice to any contractual warranty claims against the seller.

Methods of support

Appliance repairs must be carried out by an authorised Service Centre. If the faulty appliance is under warranty, it must be sent to the Service Centre together with a fiscal document evidencing the date of sale or delivery.

INTRODUCCIÓN

PROBLEMAS E SOLUÇÕES

ASSISTÊNCIA E GARANTIA

POPIS PŘÍSTROJE A PŘÍSLUŠENSTVÍ

Manual assistant
Powered by Anthropic
Waiting for your message
Product information

Brand : IMETEC

Model : Ecoextreme Pro++ C2-100

Category : Vacuum Cleaner