Livarno Lux HG04063 - Uncategorized

HG04063 - Uncategorized Livarno Lux - Free user manual and instructions

Find the device manual for free HG04063 Livarno Lux in PDF.

📄 2 pages English EN Download 💬 AI Question 10 questions ⚙️ Specs
Notice Livarno Lux HG04063 - page 1
Pick your language and provide your email: we'll send you a specifically translated version.
Product Type LED Torch
Brand Livarno Lux
Model HG04063
IP Rating IP65 (Water jet proof)
Light Source LED (non-replaceable)
Battery Type 3 x AA (1.5V)
Battery Life Approx. 3 hours
Number of Light Modes 5 (100% brightness, ECO-mode, SOS, Flashing, OFF)
Beam Focus Adjustable by sliding lamp head
Strap Included Yes
Weight 311 g
Material Plastic and metal
Intended Use Indoor and outdoor, private use
Not Suitable For Household room illumination
Cleaning Wipe with a soft, dry cloth; do not use liquids
Disposal Recycle according to local regulations for electronic devices and batteries
Warranty 3 years from date of purchase
Package Contents LED Torch, 3 x AA batteries, strap, user manual
Replacement Parts LED is not replaceable; entire product must be replaced if illuminant fails
Safety Warnings Do not stare into beam; keep batteries out of reach of children; do not recharge non-rechargeable batteries

Frequently Asked Questions - HG04063 Livarno Lux

How do I insert or replace the batteries?
Switch the torch off. Unscrew the end cap anticlockwise and remove it. Pull the battery cartridge out. Insert 3 x AA batteries with correct polarity (as shown on the cartridge). Slide the cartridge back in, replace the end cap, and screw it clockwise to tighten.
How do I switch between light modes?
Press the ON/OFF button repeatedly. Each press cycles through: 100% brightness, OFF, ECO-mode, OFF, SOS signal, OFF, Flashing mode, OFF. The sequence repeats after 8 presses.
What does IP65 mean?
IP65 means the torch is dust-tight and protected against water jets from any direction. It is not fully submersible but can withstand rain or splashing water.
Can I use rechargeable batteries?
Yes, you can use rechargeable batteries, but ensure they are of the same type and voltage. Do not mix rechargeable and non-rechargeable batteries, and never recharge non-rechargeable batteries.
How do I clean the torch?
Clean only the exterior with a soft, dry cloth. Do not use liquids or detergents, as they may damage the product. Avoid getting water inside the torch.
Is the torch waterproof?
The torch has an IP65 rating, meaning it is water jet proof but not submersible. It can withstand rain or splashes but should not be submerged in water.
How long does the battery last?
With fresh batteries, the torch provides approximately 3 hours of continuous light at full brightness. ECO mode may extend this time.
What is the warranty period?
The product comes with a 3-year warranty from the date of purchase against material and manufacturing defects. The original sales receipt is required as proof of purchase.
Can the LED be replaced?
No, the LED is not replaceable. If the illuminant fails at the end of its life, the entire product must be replaced. Do not attempt to open the lamp head.
Can I use this torch as a signal light for traffic?
No, the torch is not intended for use as a traffic signal or for securing accident scenes. The blinking mode may only be used as an additional signal, but legal provisions for accident scene security must still be followed.

User questions about HG04063 Livarno Lux

0 question about this device. Answer the ones you know or ask your own.

Ask a new question about this device

The email remains private: it is only used to notify you if someone responds to your question.

No questions yet. Be the first to ask one.

Download the instructions for your Uncategorized in PDF format for free! Find your manual HG04063 - Livarno Lux and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. HG04063 by Livarno Lux.

USER MANUAL HG04063 Livarno Lux

LED TORCH Operation and

[Non-Text]

TIESIOS FORMQS

LED KISENINIS ZIBINTAS

IAN 306051

PL LT

Technical diagram of a flashlight with labeled components and internal structure

LED Torch

- Introduction

We congratulate you on the purchase of your new product. You have chosen a high quality product. The instructions for use are part of the product. They contain important information concerning safety, use and disposal. Before using the product, please familiarise yourself with all of the safety information and instructions for use. Only use the product as described and for the specified applications. If you pass the product on to anyone else, please ensure that you also pass on all the documentation with it.

- Intended use

The product is intended for indoor and outdoor use. The product is only intended for private use and is not intended for commercial use or for use in other applications. The product withstand extreme physical conditions of vibration (1.0 m²/s² 200–2000 Hz).

■ Not suitable for household room illumination.

(2)

• Description of parts

1 lamp

Lamp

2 Torch

3 Batter

4 Battery cartridge

- Technical data

p. II

Bulb:

Batteries:

5 End cap

5 End cap 6 ON (OP

ON/OF

7 Strap

广力云

[Non-Text]

[Non-Text]

  1. 1.20

The LED canne

ect current], A.

GB

Light on time:

Degree of pr

5

approx. 3 hr

: IP65 (Water jet proof)

Livarno Lux HG04063 - - Introduction - 1

- Scope of delivery

LIFD Torch

FLED TOUCH

9 Batteries

广力云智慧零售收银系统

-

A

PLEASE KEEP THE INSTRUCTIONS IN A SAFE PLACE IF PASSING THIS

PLEASE KEEP THE INSTRUCTIONS IN A SAFE PLACE IF PASSING THIS PRODUCT ON TO A THIRD PARTY ALSO INCLUDE ALL DOCUMENTS.

PRODUCT

-

1

1

represents a danger of suffocation. Children frequently underestimate the

dangers

product

■ This product can be used by children aged from 8 years and above and

periods

persons with reduced physical, sensory or mental capabilities of lack of

experience and knowledge if they have been given supervision or instruction

concerning use of the product in a safe way and understand the hazards

involved. Children shall not play with the product. Cleaning and user main-

tenance shall not be made by children without supervision.

⚠️ CAUTION! RISK OF INJURY! Please do not use this product if you find

that it is damaged in any way

■ Do not stare into the beam

■ Check whether all of the parts are correctly fitted. If the product is not

- Anschl. Thalmer, all of the pans are currently missed completely assembled there is a degree of injury:

- correctly assembled there is a da

■ The MMHMAN is not replaceable.

■ If the illuminant fails at the end of its life, the entire product must be replaced.

The signal lamp should not be used to secure an accident scene. The blink

feature may only be used as an additional signal. The accident scene must

be secured according to the legal provisions at all times.

Note: Do not use this item for marking hazardous areas offside from road

traffic (as a signal light).

^

Safety instructions for batteries /

rechargeable batteries

A WARNING! DANGER TO LIFE! Keep batteries / rechargeable batteries

WARNING: BANOLK TO LIFE. Keep batteries/ rechargeable batteries out of reach of children. If accidentally supplied seek immediate medical

out of reach of children. If accidentally swallowed seek immediate medical

GNE

CAUTION! DANGER OF EXPLOSION! Never recharge

m = 311

non-rechargeable batteries. Do not short-circuit batteries / recharge-

able batteries and / or open them. Overheating, fire or bursting

able balances and / of open items. Overhealing, fire or bursing

can be the result.

■ Never throw batteries / rechargeable batteries into fire or water.

■ Do not exert mechanical loads to batteries / rechargeable batteries.

Risk of batteries / rechargeable batteries leakage

■ Avoid extreme environmental conditions and temperatures, which could

affect batteries / rechargeable batteries, e.g. radiators / direct sunlight.

■ If batteries/rechargeable batteries have leaked, avoid contact with skin,

eyes and mucous membranes with the chemicals! Flush immediately the

affected areas with fresh water and seek medical attention!

rechargeable batteries can cause bums on contact with the skin.

Wear suitable protective gloves at all times if such an event occurs

In the event of a battery leak, immediately remove it from the product to

in the case of a facility is being immediately, therefore it from this procedure to prevent damage.

- Only use the can

■ Only use the same type of batteries/ rechargeable batteries. DO non mix used and new batteries / rechargeable batteries

Used and new batteries / rechargeable batteries.

■ Remove the batteries/ rechargeable batteries if the product will not be used

for a longer period.

Risk of damage of the product

■ Only use the specified type of battery / rechargeable battery!

- When inserting ensure the correct polarity! This is shown on the end of the

battery cartridge 4.

- Clean the contacts on the battery and in the battery cartridge 4 before

inverting

- Remove exhausted batteries / rechargeable batteries from the product

■ REMOVA

immedia

● Bringing into use

- Inserting / replacing the batteries

Note: Switch the product off before you insert or remove the batteries 3.

□ Screw off the end cap 5 anticlockwise and take it off the torch 2.

□ Pull the battery cartridge 4 out of the battery compartment.

- Insert the (new) batteries into the battery cartridge. 4 and insert the

□ Insert the (NEW) batteries into the battery carriage 4 and insert the cartridge back into the battery compartment

Note: Make sure you fit the batteries the right way round (polarity) [see Fig 1]

Note: Malls are you in the batteries the high way found [paramy] [000-15]. The polarity is displayed in the battery electrode.

The polarity is displayed in the battery carriage [4]. But the and can [5] back in place to the back [6] and view it clockwise to

- For the end cap ③ back in place to the torch ② and screw if clockwise is

tighten it.

- Start of operation

☐ To change the lighting mode, press the ON / OFF button △ as listed in

the following table:

1.2.1 1

ON/OFF button
100% brightnessx 1
OFFx 2
ECO-modex 3
OFFx 4
SOS signalx 5
OFFx 6
Flashing modelx 7
OFFx 8

□ Focus the beam by sliding the lamp head □ upward or downward.

□ You can secure the product by using the strap 7.

- Cleaning and care

= Under no circumstances should you use liquids or detergents, as these will

■ Under the circumstances should you use liquids or detergents, as most damage the product.

□ The product should only be cleaned on the outside with a soft cloth.

- Disposal

The packaging is made entirely of recyclable materials, which you may dispose

of at local recycling facilities.

B

Observe the marking of the packaging materials for waste separation, which are marked with abbreviations (a) and numbers (b) with following meaning: 1–7: plastics / 20–22: paper and fibreboard / 80–98: composite materials.

©

The product and packaging materials are recyclable, dispose of it separately for better waste treatment. The Triman logo is valid in France only.

[Non-Text]

Contact your local refuse disposal authority for more details of how to dispose of your worn-out product.

X

To help protect the environment, please dispose of the product properly when it has reached the end of its useful life and not in the household waste. Information on collection points and their opening hours can be obtained from your local authority.

Faulty or used batteries / rechargeable batteries must be recycled in accordance

with Directive 2006/66/EC and its amendments. Please return the batteries /

rechargeable batteries and / or the product to the available collection points.

B

Environmental damage through incorrect disposal

of the batteries / rechargeable batteries!

Batteries / rechargeable batteries may not be disposed of with the usual domestic

waste. They

treatment ru

follows: Cd = cadmium, Hg = mercury, Pb = lead. That is why you should dispose of used batteries / rechargeable batteries at a local collection point.

- Warranty

The product has been manufactured to strict quality guidelines and meticulously examined before delivery. In the event of product defects you have legal rights against the retailer of this product. Your legal rights are not limited in any way by our warranty detailed below.

The warranty for this product is 3 years from the date of purchase. Should this

product show any fault in materials or manufacture within 3 years from the date

of purchase, we will repair or replace it - at our choice - free of charge to you.

The warranty period begins on the date of purchase. Please keep the original

sales receipt in a safe location. This document is required as your proof of pur-

chase. This warranty becomes void if the product has been damaged, or used

or maintaine

The warranty applies to defects in material or manufacture. This warranty does

not cover product parts subject to normal wear, thus possibly considered consu-

mables (e.g. batteries) or for damage to fragile parts, e.g. switches, rechargeable

batteries or glass parts.

C6 IP65

c c n 05

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

m = 311

GB

-

[Non-Text]

m = 311

The Ground Truth image displays a single, solid horizontal line. According to Rule 2 (UNDERSCORE & LINE RULES), this is a stylistic or background line, not a placeholder underscore. Therefore, the OCR result must ignore it and output nothing or only meaningful text. The provided OCR content is "____", which consists of four underscores. This is an incorrect interpretation of the line as a placeholder, violating the rule that stylistic lines must be ignored. The OCR has hallucinated placeholder underscores where none should exist in the GT. Hence, the OCR result is inconsistent with the Ground Truth.

[Non-Text]

1

-

1.2

-

-

m = 311

The Ground Truth image displays a single, solid horizontal line. According to Rule 2 (UNDERSCORE & LINE RULES), this is a stylistic or background line, not a placeholder underscore. Therefore, the OCR result must ignore it and output nothing or only meaningful text. The provided OCR content is "____", which consists of four underscores. This is an incorrect interpretation of the line as a placeholder, violating the rule that stylistic lines must be ignored. The OCR has hallucinated underscores where none should exist based on the GT's visual context. Hence, the OCR result is inconsistent with the Ground Truth.

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

-

The Ground Truth image displays a single, solid horizontal line. According to Rule 2 (UNDERSCORE & LINE RULES), this is a stylistic or background line, not a placeholder underscore. Therefore, the OCR result must ignore it and output nothing or only meaningful text. The provided OCR content is "____", which consists of four underscores. This is an incorrect interpretation of the line as a placeholder, violating the rule that stylistic lines must be ignored. The OCR has hallucinated underscores where none should exist based on the GT's visual context. Hence, the OCR result is inconsistent with the Ground Truth.

Manual assistant
Powered by Anthropic
Waiting for your message
Product information

Brand : Livarno Lux

Model : HG04063

Category : Uncategorized