P2001-1 - Baby products Vevor - Free user manual and instructions

Product Type	Baby Playpen
Brand	Vevor
Model	P2001-1
Recommended Age	6 to 24 months
Number of Panels	8
Maximum Height	890 mm (35 in)
Frame Material	Steel
Fabric Material	Polyester (estimated)
Fixation Type	Floor Suction Cups
Included Accessories	16 side tubes, 8 top tubes, 8 bottom tubes, 8 fabric sheets, 2 hanging hooks
Care and Cleaning	Clean suction cups with clear water; fabrics can be wiped with a damp cloth
Recommended Use	Indoor play and sleep
Closure Type	Zippers and locking switches
Safety	Avoid cords, do not add nets or covers, supervision required
Product Weight	Not specified (estimated 8-10 kg)
Dimensions of one panel	Approximately 60 cm x 60 cm (estimated)
Repairability	Spare parts available: tubes, connectors, suction cups
Instruction manual included	Yes, in French (95 pages)

Frequently Asked Questions - P2001-1 Vevor

How to assemble the Vevor P2001-1 baby playpen?

First assemble each panel: insert the top, bottom and side tubes into the connectors, then place the fabric sheet and close the zippers. Then connect the panels together starting with the top hinge, then insert the retractable post into the bottom connector. Make sure all switches are locked before use.

From what age is this playpen suitable?

The product is suitable for children aged 6 to 24 months. Stop using it when the child is able to climb or exceeds the height of 890 mm (35 inches).

How to clean the playpen's suction cups?

The suction cups can be cleaned with clear water to remove dust. Make sure the floor is clean before attaching them to ensure good adhesion.

Can I use the playpen with a water mattress?

No, never use a water mattress with this product. This could present a suffocation risk.

How to store the playpen when not in use?

Pull the switch upward to unlock it, then fold the panels. You can follow method A described in the manual: turn off all switches and activate them to fold.

What to do if a part is missing or damaged?

Contact Vevor customer service. Spare parts such as tubes, connectors and suction cups can be replaced individually.

Can I add or remove panels to change the shape of the playpen?

Yes, you can change the size or shape by adding or removing panels, according to the instructions in the manual.

Is it safe to leave my baby alone in the playpen?

No, constant supervision is required to ensure the child's safety, even inside the playpen.

How to avoid choking hazards with this product?

Do not place small objects inside the playpen. Do not hang strings or cords above the product. Make sure the zippers are properly closed.

Can the playpen be used outdoors?

The playpen is designed for indoor use. The suction cups require a clean, dry floor. Avoid exposing it to excessive moisture.

USER MANUAL P2001-1 Vevor

BABY PLAYPEN

MODEL: P2001-1

MODEL: P2001-1 50*50*27.36 inch / 1270*1270*695 mm

This is the original instruction. Please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product received. Please forgive us that we won't inform you again if there are technology or software updates on our product.

Warning - To reduce the risk of injury, user must read instructions manual carefully.

WARNING

1. Read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR FUTURE USE.
2. Failure to follow these warnings and the instructions could result in serious injury or death.
3. This product is suitable for children aged 6 months to 24 months.
4. The product, including side rails, must be fully erected prior to use.
5. Top support member must be installed prior to use. Failure to install result in child falling out of product.
6. Strings can cause strangulation! Never place items with a string around child's neck such as hood strings or pacifier cords. Never suspend strings over product or attach strings to toys.
7. Discontinue use of the product when child is able to climb out or the height of 35 in. (890 mm).
8. Child can become entrapped and die when improvised netting or covers are placed on top of product.
9. Never add such items to confine the child in the product.
10. When the child is able to pull to a standing position, remove bumper pads, large toys, and other objects that could serve as steps for climbing out.
11. Never place the product near a window where cords from blinds or curtains could strangle a child.
12. Always provide the supervision necessary for the continued safety of your child. When used for playing, never leave the child unattended.
13. To reduce the risk of SIDS, pediatricians recommend that healthy infants be placed on their backs to sleep, unless otherwise advised by your physician.
14. Never use plastic shipping bags or other plastic film as mattress covers, as they are not sold or intended for that purpose. They can cause suffocation.
15. Never use a water mattress with this product.
16. Before installation, please make sure to clean the floor thoroughly to ensure a tight connection between the suction cup and the floor. During installation, apply force firmly on the column with the suction cup to ensure a secure connection between the suction cup and the floor.
17. Maintenance instruction: If the suction cup becomes contaminated after repeated use, it can be cleaned with water. After cleaning, the suction of the suction cup can be enhanced.

INSTALLATION NOTE

1. Parts for Baby Playpen

Name	Side Tube	Upper Tube	Bottom Tube	Fabric sheet	Hanging hooks
Qty	1 X 16	1 X 8	1 X 8	1 X 8	1 X 2
Image

1.1. Details for Single Panel

Note: The switch of the upper tube and the connector of the lower tube must be placed on the same side (this means hinges should stick out on the same side), otherwise the panels cannot be connected with each other.

1.2. Installation Step for Single Panel

1). Connect the side tube to the bottom tube.

2). Insert the corresponding fabric cover into the side tube.

3). Match the suitable upper tube to the side tube.

4). Close both zippers around the tubes.

Note:

1. After installing single pieces, please carefully check whether the zipper is properly closed and the corresponding steel tubes are aligned.
2. For the sake of safety, please make sure that all single pieces are installed correctly according to the instructions before connecting them together.

2. Accessories description

Name	QTY	Image	Installation Image Panel
Panel	8

2.1. Details for Single Panel

1 Fixed switch 2 Button Connector Solid pole Retractable pole

Note:

1. The floor where the products are placed and the product suction cup need to be cleaned thoroughly before pressing.
2. The suction cup can be cleaned with clean water.

2.2. Installation Step for fence

Note: The pieces need to be connected based on the following procedure: connect the top hinge first, then insert the retractable pole into the bottom connector, push it upward, and connect together.

1). Connect two panels for one side.

2). Connect another 2 panels for the second side.

3). Repeat, connect the third side. 4). Connect the last side.

Note: You can change its dimension or shape by adding or removing some panels.

2.3. Wrong Installation Step

Do not install the reminder label side inside; all zippers should be put outside.

Caution:

1. After installation, please check and make sure all switches are locked in use.
2. For safety reasons, make sure that the baby playpen is installed according to the installation instructions.
3. To avoid danger of choking, do not place any small items which cause choking inside.
4. Before using, please check the playpen carefully. If there is any damage, please stop using.

STORAGE INSTRUCTIONS

Note: Before storing, please pull up the switch to make it unlocked. Method A

Step 1: Lift up the switch to make it unlocked. The switch is in active status.

Step 2: According to step 1, turn off all switches, make them active.

Method B

1

Pull up all switches, make them active (the same as step 1 in method A).

2

Using a screwdriver, pen, or other hard sticks, push from bottom to top to remove it from the connector.

3

Take them apart.

4

Continue to take the top apart.

5

Only remove one piece.

6

Make all pieces overlap.

Manufacturer: Shanghaimuxinmuyeyouxiangongsi

Address: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN.

Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australia

Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

UK

REP

YH CONSULTING LIMITED. C/O YH Consultin Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4A>

EC

REP

Affordable. Reliable. Home Improvement.

BABY PLAYARD

MODEL: P2001-1

MODEL: P2001-1 50*50*27.36 inches\1270*1270*695 mm

1). Connect the side tube to the bottom tube.

2). Insert the corresponding fabric cover into the side tube.

3). Match the suitable upper tube to the side tube.

4). Close both zippers around the tubes.

Note:

1). Connect two panels for one

62). Connect another 2 panels for the second side.

3). Repeat, connect the third side. 4). Connect the last side.

Do not install the reminder label side inside, all zippers should be put outside.

Caution:

Step 1: Lift up the switch to make it unlocked. The switch is in active status.

Method B

1

Pull up all switches, make them active (the same as step 1 in method A).

2

Using a screwdriver, pen or other hard sticks, push from bottom to top to remove it from the connector.

3

Take them apart.

4

Continue to take the top apart.

5

Only remove one piece.

6

Make all pieces overlap.

Address: Shuangchenglu 803nong11hao1602A-1609shi, Baoshan District, Shanghai 200000 CN.

Imported into Australia: SIHAO PTY LTD. 1 ROKEVA STREET, ASTV NSW 2122 Australia

Place, Rancho Cucamonga, CA 91730

UK

REP

YH CONSULTING LIMITED. C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4A>

EC

REP

Affordable. Reliable. Home Improvement.

BABY PLAYARD

MODEL: P2001-1

MODEL: P2001-1 50*50*27.36 inches\1270*1270*695 mm

1). Connect the side tube to the bottom tube.

2). Insert the corresponding fabric cover into the side tube.

3). Match the suitable upper tube to the side tube.

4). Close both zippers around the tubes.

Note:

1). Connect two panels for one side.

2). Connect another 2 panels for the second side.

3). Repeat, connect the third side. 4). Connect the last side.

Do not install the reminder label side inside, all zippers should be put outside.

Caution:

Step 1: Lift up the switch to unlock it. The switch is in active status.

Method B

1

Pull up all switches, make them active (the same as step 1 in method A).

2

Using a screwdriver, pen or other hard sticks, push from bottom to top to remove it from the connector.

3

Take them apart.

4

Continue to take the top apart.

5

Only remove one piece.

6

Make all pieces overlap.

Address: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, Shanghai 200.000 CN.

YH CONSULTING LIMITED. C/O YH Consultin Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4A>

EC

REP

Affordable. Reliable. Home Improvement.

BOX PER BAMBINI

MODELLO: P2001-1

MODELLO: P2001-1 50*50*27,36 pollici\1270*1270*695 mm

1). Connect the side tube the bottom tube.

2). Insert the corresponding fabric cover into the side tube.

3). Match the suitable upper tube to the side tube.

4). Close both zippers around the tubes.

Note:

1). Connect two panels for one side.

2). Connect another 2 panels for the second side.

3). Repeat, connect the third side. 4). Connect the last side.

Do not install the reminder label side inside, all zippers should be put outside.

Attention:

Step 1: Lift up the switch to unlock it. The switch is in active status.

Method B

YH CONSULTING LIMITED. C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4A>

EC

REP

Affordable. Reliable. Home Improvement.

BABY PLAYARD

MODEL: P2001-1

MODEL: P2001-1 50*50*27.36 inches\1270*1270*695 mm

1). Connect the side tube to the bottom tube.

2). Insert the corresponding fabric cover into the side tube.

3). Match the suitable upper tube to the side tube.

4). Close both zippers around the tubes.

Note:

1). Connect two panels for one side.

2). Connect another 2 panels for the second side.

3). Repeat, connect the third side. 4). Connect the last side.

Do not install the reminder label side inside, all zippers should be put outside.

Caution:

Step 1: Lift up the switch to make it unlocked. The switch is in active status.

Method B

1

Pull up all switches, make them active (the same as step 1 in method A).

2

Using a screwdriver, pen or other hard sticks, push from bottom to top to remove it from the connector.

3

Take them apart.

4

Continue to take the top apart.

5

Only remove one piece.

6

Make all pieces overlap.

YH CONSULTING LIMITED. C/O YH Consultin Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4A>

EC

REP

Affordable. Reliable. Home Improvement.

KOJEC DLA NIEMOWLĄT

MODEL: P2001-1

MODEL:P2001-1 50*50*27,36 cal\1270*1270*695 mm

1). Connect the side tube to the bottom tube.

2). Insert the corresponding fabric cover into the side tube.

3). Match the suitable upper tube to the side tube.

4). Close both zippers around the tubes.

1). Connect two panels for one side.

2). Connect another 2 panels for the second side.

3). Repeat, connect the third side. 4). Connect the last side.

Do not install the reminder label side inside, all zippers should be put outside.

Step 1: Lift up the switch to make it unlocked. The switch is in active status.

Method B

1

Pull up all switches, make them active (the same as step 1 in method A).

2

Using a screwdriver, pen, or other hard stick, push from bottom to top to remove it from the connector.

3

Take them apart.

4

Continue to take the top apart.

5

Only remove one piece.

6

Make all pieces overlap.

Address: Shuangchenglu 803nong11hao1602A-1609shi, Baoshan District, Shanghai 200000 CN.

Imported into AUS: SIHAO PTY LTD. 1 ROKEVA

STREETEASTWOOD

NSW 2122 Australia

YH CONSULTING LIMITED. C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4A>

EC

REP

Affordable. Reliable. Home Improvement.

BABY BOX

MODEL: P2001-1

MODEL: P2001-1 50*50*27,36 inch\1270*1270*695 mm

There is a reminder label on the fabric, please face upward during installation

1). Connect the side tube the bottom tube.

2). Insert the corresponding fabric cover into the side tu

3). Match the suitable upper tube to the side tube.

4). Close both zippers around the tubes.

Note:

1). Connect two panels for one

2).Connect another 2 panels for the second side.

3). Repeat, connect the third sid

4).Connect the last side

Do not install the reminder label side inside, all zippers should be put outside.

Caution:

Step 1: Lift up the switch to unlock it. The switch is now in active status.

Method B

1

Pull up all switches to make them active (same as step 1 in method A).

2

Using a screwdriver, pen, or other hard sticks, push from bottom to top to remove it from the connector.

3

Take them apart.

4

Continue to take the top apart.

EC

REP

MODEL: P2001-1

MODEL: P2001-1 50*50*27.36 in \ 1270*1270*695 mm

There is a reminder label on the fabric, please face upward during installation.

1). Connect the side tube to the bottom tube.

2). Insert the corresponding fabric cover into the side tube.

3). Match the suitable upper tube to the side tube.

4). Close both zippers around the tubes.

Note:

1). Connect two panels for one side.

2). Connect another 2 panels for the second side.

3). Repeat, connect the third side.

4). Connect the last side.

Do not install the reminder label side inside, all zippers should be put outside.

Caution:

Step 1: Lift up the switch to make it unlocked. The switch is in active status.

Method B

1

Pull up all switches, make them active (the same as step 1 in method A).

2

Using a screwdriver, pen or other hard sticks, push from bottom to top to remove it from the connector.

3

Take them apart.

4

Continue to take the top apart.

Manufacturer: Shanghaimuxinmuyeyouxiangongsi

Address: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, Shanghai 200 000, People's Republic of China.

Imported to Australia: SIHAO PTY LTD. 1 ROKEVA STREET EASTWOOD

NSW 2122 Australia

Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, California 91730

UK

REP

YH CONSULTING LIMITED. C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4A>

EC

REP