HCL-13 - Cleaning gun Vevor - Free user manual and instructions

Brand	Vevor
Model	HCL-13 (also HCL-15A)
Product Type	Dry Cleaning Gun
Operating Pressure	0.6 - 0.92 MPa
Operating Temperature	5 to 50 °C
Brush Material	PVC
Power Supply	Pneumatic (air compressor)
Required Air Flow	> 200 L/min
Required Air Tank Capacity	> 70 L
Required Compressor Power	> 2500 W
Compatible Cleaning Agents	Cleaning solutions and agents (no adhesive)
Cleaning After Use	Place the nozzle in clean water, pull the trigger for 1 to 3 seconds, then dry and store away from sunlight
Safety Instructions	Keep the gun clean with alcohol to prevent corrosion; use only genuine accessories
Repairability	Using non-genuine accessories or non-professional service voids the warranty; do not disassemble the device
Technical Support	www.vevor.com/support
Manual Languages	FR, DE, EN, IT, NL, PL, SV, etc.
Number of Pages	48

Frequently Asked Questions - HCL-13 Vevor

What cleaning agents can I use with this gun?

Use only cleaning solutions or cleaning agents. Do not use adhesive or other viscous substances.

What air pressure is needed?

The operating pressure is between 0.6 and 0.92 MPa. The compressor must have a flow rate >200 L/min, a tank capacity >70 L, and power >2500 W.

How to clean the gun after use?

Place the nozzle in clean water, close the water valve, press the trigger for 1 to 3 seconds for self-cleaning. Remove the nozzle, dry it, and store it in a ventilated place away from sunlight.

Can I use adhesive with this gun?

No, this gun is designed only for cleaning agents and cleaning solutions. Use of adhesive is prohibited.

What to do if the gun does not work properly?

Check that the compressor meets the requirements (flow rate, tank, power). If issues persist, contact Vevor technical support via www.vevor.com/support. Do not attempt to repair it yourself.

Which models are covered by this manual?

This manual is valid for models HCL-13 and HCL-15A of the Vevor brand.

Where to find technical support and warranty?

Technical support and the electronic warranty certificate are available on the website www.vevor.com/support.

What is the recommended operating temperature?

The operating temperature is between 5 °C and 50 °C.

How to install the gun on the compressor?

Use raw material tape wrapped at the connector to ensure sealing. Make sure the compressor is off when connecting.

Can I use non-genuine accessories?

No, only genuine accessories and professional service are recommended. Use of non-compliant accessories voids the warranty and may damage the device.

USER MANUAL HCL-13 Vevor

Technical Support and E-Warranty Certificate www.vevor.com/support

CLEANING GUN

MODEL: HCL-13 HCL-15A

We continue to be committed to provide you tools with competitive price. "Save Half", "Half Price" or any other similar expressions used by us only represents an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and does not necessarily mean to cover all categories of tools offered by us. You are kindly reminded to verify carefully when you are placing an order with us if you are actually Saving Half in comparison with the top major brands.

VEVOR®

TOUGH TOOLS, HALF PRICE

CLEANING GUN

MODEL: HCL-13 HCL-15A

HCL-15A HCL-13

NEED HELP? CONTACT US!

Have product questions? Need technical support? Please feel free to contact us:

Technical Support and E-Warranty Certificate www.vevor.com/support

This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product received. Please forgive us that we won't inform you again if there are technology or software updates on our product.

INSTRUCTIONS

1. Please read this instruction book carefully before you start using the machine. You will find many useful hints which will help you to keep machine always in its first-class condition.

Tips: With raw material tape wrapped to the connector when use

Warning!

Keep the gun clean from the liquor which is detained, otherwise, it will corrode inner side of the bottle.

Note: The model selection of the air compressor should meet the following parameters: the exhaust volume should be >200L/min, the gas storage tank should be >70L, and the power should be >2500W

It should be cleaned immediately after use

EFFICIENT DRY-CLEAN GUN
PRESSURE	0.6-0.92 Mpa
TEMPERATURE	5~50°C
BRUSH	PVC

Attention!

1. Return to maintenance if you have any abnormal and damage when use
2. We won't service if you don't use original accessories and Professional consumables.
3. We won't service if you use it in a wrong way or do not pass our tech guidance, dismantled and installed the part of the apparatus at will.

Attention!

Keep the gun clean from the liquor which is detained, otherwise, it will corrode inner side of the bottle.

Cleaning: put the nozzle into clean water, close the liquor valve, pull the trigger and then it will wash automatically, get the nozzle out, dry it, and maintain it without direct sunlight.

All you need to do is put the nozzle into water and pull the trigger for a few seconds.

Note: 1. Only applicable to cleaning agents and cleaning solutions, cannot use glue etc.

NoteTips of notes please check before you use it
warning!	Warning that means if you don't follow this, it may Cause accident Endanger life safety
Attention!	Attention that means you need Specification Operation,or it damage the machine and your body.

Manufacturer: Shanghai muxin muye youxian gongsi

Address: Shuang Cheng Lu, 803 Nong, 11 Hao, 1602A-1609 Shi, Baoshan Qu, Shanghai 200000, CN.

Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREET, EASTWOOD NSW 2122, Australia

Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

UK

REP

YH CONSULTING LIMITED. C/O YH Consulting Limited, Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX

EC

REP

Technical Support and E-Warranty Certificate

www.vevor.com/support

VEVOR®

TOUGH TOOLS, HALF PRICE

HCL-15A

HCL-13

NEED HELP? CONTACT US!

YH CONSULTING LIMITED. C/O YH Consulting Limited, Bureau 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX

REPRÉSENTANT

DE LA CE

E-CrossStu GmbH

Mainzer Landstr. 69,

MODEL: HCL-13 HCL-15A

MODEL: HCL-13 HCL-15A

HCL-15A

HCL-13

YH CONSULTING LIMITED. C/O YH Consulting Limited

Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX

E-CrossStu GmbH

Representative in the EC

Mainzer Landstr.69,

60329 Frankfurt am Main.

VEVOR®

TOUGH TOOLS, HALF PRICE

www.vevor.com/support

VEVOR®

TOUGH TOOLS, HALF PRICE

MODEL: HCL-13 HCL-15A

MODEL: HCL-13 HCL-15A

HCL-15A

HCL-13

Imported into AUS: SIHAO PTY LTD. 1 ROKEVA STREET, EASTWOOD NSW 2122 Australia

Imported into USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

YH CONSULTING LIMITED. C/O YH Consulting Limited, Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX

electronics www.vevor.com/support

VEVOR®

TOUGH TOOLS, HALF PRICE

MODEL: HCL-13 HCL-15A

MODEL: HCL-13 HCL-15A

HCL-15A

HCL-13

Road, Staines-upon-Thames, Surrey, TW18 4AX

REPRESENTANTE CE

E-CrossStu GmbH

Mainzer Landstr.69,

MODEL: HCL-13 HCL-15A

MODEL: HCL-13 HCL-15A

HCL-15A

HCL-13

NEED HELP? CONTACT US!

YH CONSULTING LIMITED. C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-

Thames, Surrey, TW18 4AX

E-CrossStu GmbH

Mainzer Landstr.69,

60329 Frankfurt am Main.

Przedstaw ciel UE

VEVOR®

TOUGH TOOLS, HALF PRICE

MODEL: HCL-13 HCL-15A

MODEL: HCL-13 HCL-15A

HCL-15A

HCL-13

NEED HELP? CONTACT US!

YH CONSULTING LIMITED. C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX

warranty certificate www.vevor.com/support

VEVOR®

TOUGH TOOLS, HALF PRICE

MODEL: HCL-13 HCL-15A

MODEL: HCL-13 HCL-15A

HCL-15A

HCL-13

NEED HELP? CONTACT US!

YH CONSULTING LIMITED. C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX

www.vevor.com/support