AutoFeed+ 60X - Shredder GBC - Free user manual and instructions

USER MANUAL AutoFeed+ 60X GBC

Remove Jam Credit Card Shred

g

English

Safety

Please read and keep these important safety instructions.

The following symbol words is found on the product indication: you could be seriously hurt or killed if you open the machine. DO NOT OPEN.

For a full copy of the operating instructions, htns &rips and transclating guide, please visit www.gbc.com.

Warning: Do not march ratter, baware of sharp edges.

Warning: Moving parts hazard, keep hands away Iron rolls wills in operation.

The power box must be connected to a socket-couler with earthing connection.

• Please read all the safety information and the instructions; the manufacturer is not liable for cases of material damage or personal injury caused by incorrect handling as non-compliance with the safety instructions. In such cases, the warranty will be voided.
  Only use the unit for its intended purpose.
• Do NOT load the auto-feed chamber with unopened junk mail, magazines, bound documents etc.
  The unit must only be connected to a supply voltage corresponding to the electrical rating shown on the unit.
  Do NOT alter the attachment plug. The plug is con gued for the appropriate electrical supply.
• limit should be connected to a socket port near the equipment that is easily accessible. Ensure the cable is not likely to trip up a pass by.
  +Do not connect multiple adapines or use with an extension cable.
• Do not attempt to service or repair the unit yourself. Please return to supplier.
  If recycling, separate paper and credit card shreds.
• Do not use this unit if the cable or plug have been damaged, after it malfunctions, or after it has been damaged in any manner.
• Inpug your shredder before moving it or when it is nut in use for an extended period of time.
  Care should be taken when moving equipment to avoid any unlevelled surfaces.
  +1ock casers in place, if lock provided.
• Keep power card away from causes. Clusters can damage the power card. If power card insulation is damaged, disconnect the plug from the wall socket.
  The device is intended for use indoors. Never use outdoors.
  -Keep the device away from moisture.
  Be vigilant at all times, and always be careful what you are doing. Do not use electrical equipment if you are locking in concentration or awareness, or are under the influence of drugs, alcohol or medication. Even a moment of inadvertence can lead to serious injuries when using electrical equipment.
  Do not attempt to open, modify or repair the device. Do not drop, puncture, break or expose to high pressure.
  Alterations to the device and technical modi cations are not permitted.
• Check the device and cable (and if applicable, the adapter) for any damage before use. If there is any visible damage, a strong odour, or excessive overloading of components, unplug all the components immediately and step using the device.
  Shredler must be discovered from any sources of any said for an extended period of time.
  10
• Never bypass the safety interlock (strictly forbidden and dangerous, especially when unit is connected in a power source).
  Do not see on the shredder doh; this may damage the oon and will not be covered by you warrnly.
• Failure to follow these instructions could result in damage to injury and will invalidate your warranty.
• Although this childcare has been designed to comply with I.L.6788 - KN 62968 safety standards including the "prabeccessibility tests", do not operate the childcare near children's piers.

Warning Symbols

Warning symbols

Keep loose jewelry clean

Ties and loose clothing hazard

Keep long hair clean

This equipment is not intended for use by children.

No aresps, Do not use spray cleanes or lubricants.

Max shee capacity

No/1s

No heavy duty staples above 1 inch/26 mm

Warning: moving parts

Hopper Filling Symbols

图

Maximum sheet level

Warning: no heavy duty staples above 1 inch; 26 mm

Warrin: no more than 25 sheets stapled together

Warning: no bound documents

Warning no multiple folded sheets

Wrrnng hnnnnnne nnnnne

Warning: no paperclips above 1.25 inch; 32 mm

Warring, no unproposed mail.

Warning no magazines

Warning: no paper at card above 200gsm

Buttons & Indicators

Control Buttons	Auto-start and stand-by button (press one time)	All Models
	Manual reverse button (hold down)
	Manusf forward run button (hold down)
Status Indications	Ready indication
	Over heeding indication (Allow to cool)
	Overloaded / Jam indication (Reduce sheet / remove jam)
	Bin full indication (open door and empty the bin)
	Door open or shredder head removed indication (close door firmly or replace head on bin)
	Hopper locked indication (unlock by entering 4 digit combination)	300, 600, 760 models
Hopper Locking combination buttons	1 Hopper locking security combination button 1
	2 Hopper locking security combination button 2
	3 Hopper locking security combination button 3
	4 Hopper locking security combination button 4

Operation

1. Unpack the product.
2. Connect the shroud to a power outlet with voltage corresponding to the electrical rating shown on the unit
3. Ensure the ON/OFF button on the back of the machine is in the ON position, which will illuminate the blue standby symbol
4. To load the shredder, simply lift the loading door handle to open the loading door and insert documents. You can open the door further to 90 degrees for easier access if required. Load up to MAX sheets at a time into the feed chamber. Do not fill above the MAX sieve, this could damage the shredder.
5. The shredder will start the shredding cycle automatically ONLY after closing the loading door. If there is still paper in the AutoFeed chamber after first attempt, open and re-close the paper loading door a second time.
   Attention: If required you can now lock the loading door by entering a 4-digit code (see Locking the Paper Loading Door section).
6. If you only have a few sheets to shred, you can use the manual feed slot, provided the auto feed chamber is empty.
7. Insert paper to be shredded into the feed area. The shredder will detect the paper and start automatically.
8. If the shredder is left in auto mode for more than 2 minutes without being used, the shredder will automatically turn back to sleep mode in order to save power.
9. The shredder will automatically 'wake up' from sleep mode when paper is inserted into the third mouth or you open the locking door. There is no need to press the Auto button

Auto Feed Technology

The AutoFeed- shredders have been designed to automatically shred up to 750 sheets from the auto-feed chamber and up to 20 sheets through the manual feed slot. The auto-feed mechanism has been designed to handle paper fastened with staples and paper clips and to only pull a few sheets of paper into the cutting mechanism to minimize the risk of paper jams. See specifications tables for the capacity details on your model.

Locking the Paper Loading Door

For additional security the paper loading door can be locked during the shredding of confidential material. To lock shredder:
1. Place documents in tray. Close paper loading door.
2. Press any 4 digits: REMEMBER YOUR CODE! Shredder unlocks automatically when:
4dialloge isre-entered.
Shredding is complete.
- Shredder is Inactive for 30 minutes (but documents remain in tray)

Bin Full

The shredder will not function when the bin is full and the bin 'full symbol' is illuminated.

You should empty the bin.
- Pull open the bin slowly to empty.
- Push the empty bin back into place and press the auto button to resume shredding.

Over Heating

If the AutoFeed- shredder is used continuously without pausing, it may overheat and the cool down indicator will flash red. Please allow the shredder to cool down. When the shredder is ready to be used the thermometer symbol will no longer illuminate, if the shredder needs to cool down while shredding, no action is needed. The shredder will automatically restart shredding paper once it has cooled down after periods of continuous use. All you need to do is ensure paper is loaded into the chamber and the bin is empty when the machine is cooling down.

Serviceable Machines

(for 600 sheet and above)

We recommend these machines are served every 6 to 12 months by a GBC service engineer - see www.gbc.com/support for enquiries about maintenance contracts.

AutoFeed+ Shredding Capability

CAN shred the following:

Stapled paper, 1 inch / 25 mm within the corner

26/8 and 24/8 or smaller slapes - 3D0 sheets

Small sized paper. 50gam paper

• Paperclipped paper, 1 inch / 25 mm within the corner
  Canable of shedding small medium carcasses
  max wire thickness - .035 inches / 9 mm
  65-100gsm paper

Letter-8.5x11
-1/2 Sheet -5.5" x 8.5"
-Tabold-11x17

CAN shred (through the manual feed slot):

Thick paper or card

<200g/m

Glossy paper or a sheet

covered with print on both

sides.

Multiple folded sheets

11" X 17" sheets folded

in half.

CANNOT shred the following:

Heavy duty staples. Large clips. Check the length

Check the staple leg of the patroch is not longer

length is not greater than 1.254 mm.

thn.23 innes/6 m.

Bulldog clips

Bound documents

Plastic sheets

laminated documents,

plastic holders.

Magazines or other

documents bound by

multiple stapes or clips.

Adhesive labels

No serceols

No Liquid Oil

No CDs & DVDs

Lubrication of the Shredder Maintenance

GBC recommends using an oil sheet after the bin has been

enrolled three times and every three on employing this .Longest the all short into line meal supply food diet and BOLI is ,

the autofield chamber . Using an oil sheet in the auto feed

chamber will contaminate the feed rollers preventing the

auto-feed mechanism shedding. Follow the maintenance instructions if the millers become compacted.

ns on the auto-feed mechanism may become dirty

over time , presse wipe clean with a dry coth to maintainproduct performance .

The auto-star infrared sensor, located in the paper feed

y

find into the machine . Switch the stepper pad off at the turn

of the machine and carefully clean the sensor using a

cotton-sn

Limited Warranty

Cutter warranties vary by model. Limited 2 year warranty on the shredder unit.

ACCO Brands USA LLC, Four Corporate Drive, Lake Zurich IL 60047-3997 (in Canada. ACCO Brands Canada Inc., 5 Precidia Court, Brampton,

ON L8S 87, and in Mexico, ACO Mexicare, S.A. de C.V. Ax Cineo Inmobiliar Norte Parque Inmobiliar Limita 52000, Mexico Edo Co Maxco (1)

in workmanship and material under normal use and reviews for a period of 2 years after purchase and all other parts are free from defects in

worship and material under normal use and service for a period of 2 years after purchase.

ACCO Brands' obligation under this warranty is limited to replacement or repair, at ACCO Brands' option, of any warranted part found defective by

ACCO Brand s h t a

Pc

(1) if the product has been damaged

(ii) if the product has been altered by anyone other than ACCO Brands or ACCO Brands' authorized agents.

For warranty execution, please call:

1-800-541-0094 in the USA

1-600-263-1063 nCangee

01-55-1500-5700/5778 in Mexico

Orgo to www.gbcoom to register your product.

TO THE EXTENT ALLOWED BY APPLICABLE LAW, THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESSED WARRANTYES.

REPRESENTATIONS OR PROMISES INCONSISTENT WITH OR IN ADDITION TO THIS WARRANTY ARE UNAUTHORIZED AND SHALL NOT

BE BINDING ON ADO BRANDS TO THE EXPERT PENTIMED BY APPLICABLE LAWS, ANY IMplied WARDANIS (IF APPLICABLE) ARE LIMITED IN PURCHASE TO THE PURCHASE OF THE INSURANCE SERVICES STATES AND INPURACTIONS DEPUTY AS WELL INTENDED

ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU TO THE EXTENT PERMITTED.

BYAPPLICABLELAW,INNOEVENTSHALLACCOBRANDSBE LIABLEFORANYSPPECIAL,INCIDENTAL,PUNITIVE,EXEMPLARY

CONSEQUENTIAL OR SIMILAR DAMAGES, WHETHER OR NOT FORSEEABLE, SOME STATES AND JURISDICTIONS DO NOT ALLOW

THE EXCLUSION OR LIMITATION OF SPECIAL, INCIDENTIAL, PUNITIVE, EXELMARY, CONSEQUENTIAL, OR SIMILAR DAWGAS, SO THE AGREE EXCLUSION OR LIMITATION (NOT APPLICATE TO YOU)

FOR CONSUMERS WHO HAVE THE BENEFIT OF CONSUMER PROTECTION LAWS OR REGULATIONS IN THEIR JURISDICTION OF

PURCHASE OR,IF DIFFERENT,IN THEIR JURISDICTION OF RESIDENCE,THE BENEFITS CONFERRED BY THIS WARRANTY ARE IN

ADDITION TO ALL HIGHS AND REMEDIES CONVEYED BY SUCH CONSUMER PROTECTION LAWS AND REGULATIONS.

To the extent permitted by law, this warranty is not transerse end will automatically terminate if the original product purchaser sets or otherwise disposes of the product.

This warranty gives you specific legal rights. Other rights, which vary from jurisdiction to jurisdiction, may exist. In addition some jurisdictions do

not allow (i) the exclusion of certain warranties, iii) limitations on how long an implied warranty lasts and/or (ii) the exclusion or limitation of certain types of costs and/or damages, so the above limitations may not apply.

FCC CLASS B NOTICE

Note: This equipment has been tested and found to comply with the limits for a Class 8 digital device, pursuant to part 15 of the FOC Rules. These

m

communications. However, there is no guarantee that interference will not occur in a particular installation. If the equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to if this

equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. The use

Respect or relocate the receiving antenna.

Increase the separation between the equipment and receiver

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consultheaderor an expeneroe

CANADA CLASS B NOTICE

This Class B digital apparatus complee with Canadian ICES-003

MODIFICATIONS

Any modifications made to this device may yield the authority granted to the user by the FCG and/or by Industry Canada to operate this equipment.

ACCO is a registered trademark of ACOO Brands.

Copyright © 2021 AOOSBrents. All rights reserved.

*ACCO Brands North America accepts no liability for product performance or safety when other laws or brands of lubricants are used on any

part(s) of this machine.

Specifications

DéCHIQUETEUSES AUTOFEED+
	Niveau de coupe	Capacité de feuillesAlimentation auto	Capacité de feuillesAlimentation manuelle	Taille du bacGallons / Litres
AutoFeed+ 60X	P4 60 6 5,3 / 20
AutoFeed+ 100X	P4 100 8 9 / 34
AutoFeed+ 100M	P5 100 6 9 / 34
AutoFeed+ 150X	P4 150 8 11,6 / 44
AutoFeed+ 150M	P5 150 6 11,6 / 44
AutoFeed+ 230X	P4 230 10 15,9 / 60
AutoFeed+ 230M	P5 230 8 15,9 / 60
AutoFeed+ 300X	P4 300 10 15,9 / 60
AutoFeed+ 300M	P5 300 8 15,9 / 60
AutoFeed+ 600X	P4 600 15 29 / 110
AutoFeed+ 600M	P5 600 10 29 / 110
AutoFeed+ 750X	P4 750 20 37 / 140
AutoFeed+ 750M	P5 750 15 37 / 140

Fonctionnement

En marche

Advertisement: pieces mobiles

Papier brianl c reune
Imprima nona tume

imprirereceiver

Eliquetties adhesives.

Pas d'erogols

Pas d'rule liquide

Pas cd CD et DVD