301777 - Lighting Brandson - Free user manual and instructions

Product type	LED night light with motion detector
Brand	Brandson
Model	301777
Dimensions (L x H x D)	80 mm x 100 mm x 35.1 mm
Weight	Approx. 150 g (without batteries)
Power supply	3 AA 1.5 V batteries (not included)
Light source	2 SMD LED neutral white
Detection angle	120° horizontal, 90° vertical
Detection range	Up to 4 m
Operating modes	ON (permanent light), OFF (off), AUTO (automatic standby)
Illumination duration in AUTO mode	Approx. 35 seconds
Functions	Motion detection, twilight sensor, magnetic mount, wall mount
Mounting	Magnetic (on ferromagnetic surfaces) or wall-mounted (with included bracket)
Package contents	Night light, wall bracket, screws and wall plugs, adhesive tape, user manual
Care and cleaning	Clean with a soft, dry cloth; do not use abrasive cleaners
Safety	For indoor dry use; do not open or modify; avoid moisture and high temperatures
Spare parts and repairability	No spare parts available; repair by manufacturer only
General information	Compliant with WEEE directive 2012/19/EU; registration DE 67896761

Frequently Asked Questions - 301777 Brandson

How to install the batteries?

Open the battery compartment at the back of the device, insert 3 AA batteries following polarity (+/-), then close the cover carefully.

Why doesn't the light turn on in AUTO mode?

Check that the switch is set to AUTO. Make sure the batteries are in good condition and properly inserted. The twilight sensor prevents activation in bright light; place the device in a sufficiently dark location.

What is the detection range of the motion detector?

The detector covers an angle of 120° horizontal and 90° vertical, with a maximum range of about 4 meters.

How long does the light stay on after detection?

In AUTO mode, the light stays on for about 35 seconds after the last detected motion.

Can I use the night light outdoors?

No, the device is designed for indoor dry use only. It must not be exposed to moisture, rain, or snow.

How to mount the night light on the wall?

Attach the wall bracket using the provided screws and wall plugs or adhesive tape. Then hang the night light by the eyelet on the back onto the bracket.

The light stays on permanently, what should I do?

Check the switch position: if it is set to ON, switch it to AUTO or OFF. If the problem persists, replace the batteries.

Can I use rechargeable batteries?

Yes, AA rechargeable batteries of 1.2 V can be used, but the lighting duration may be reduced. Make sure they are fully charged.

How to clean the device?

Use a soft, dry cloth. Do not use chemical or abrasive cleaners. Ensure no moisture enters the device.

What to do in case of malfunction?

Refer to the 'Troubleshooting' chapter of the user manual. If the problem persists, contact customer service. Never attempt to open the device yourself.

USER MANUAL 301777 Brandson

ENG: Current drivers, user manuals and other relevant documents for this product can be found on our homepage.

Thank you for choosing a product from the Brandon range. Please read the following user manual carefully to have an enjoyable experience with your purchased product.

1. Scope of supply

• LED night light
• Mounting screws + brackets
• Adhesive pad
• Wall bracket
• User manual

2. Technical data

Power supply 3x AA 1.5V	batteries
Dimensions 80 mm x 100	mm x 35,1 mm
Coverage	• 120 ° horizontal, 90 ° vertical• 4m range
Light fittings • 2x SMD LED (neutral white)
Features • 3 modes (ON / OFF / Auto)• Magnetic bracket• Wall bracket• Movement detection• Twilight sensor

3. Initial use

Take the device out of the package and remove all the packaging material. Open the battery compartment at the back of the device and insert three AA batteries. Make sure the polarity of the contacts is correct. Then close the battery compartment properly again.

A switch is located at the back of the device. The table below explains the operation of this switch.

AUTO During darkness, the light turns on automatically as soon as any movement is detected. The light stays on for about 35 seconds.

OFF The device is turned off.

ON The device is permanently switched on. The light stays on continuously.

4. Installation

The night light can be permanently installed by using the wall bracket or the two magnets at the back which can be attached to all ferromagnetic materials as to be found on refrigerators, magnetic boards.

If you want to use the wall bracket, you have to install it on a wall at the desired position. To do this, simply use the provided mounting screws + wall plugs or the adhesive pad. Ensure that there are no power cables or water pipes at the place of installation, which could be damaged.

After installing the wall bracket, you can mount the night light on the bracket. For this purpose, a hanger is provided at the back of the night light, using which you can mount the device easily on the wall bracket.

The wall bracket is designed such that the night light can be removed at any time, for example, to change the batteries. Or if you want to use the device as a mobile light.

5. Troubleshooting

Error Corrective action
Light is not turning on	Set the switch to "AUTO" or "ON" positionInsert or replace the batteriesInstallation location is too bright
Light stays on continuously	Set the switch to "AUTO" or "OFF" position
Unwanted switching Check	the batteries and replace if necessary

6. Safety instructions and liability disclaimer

Never try to open the device to carry out repairs or conversions. Avoid contact with mains voltages. Do not short-circuit the product. The device is not certified for use in the open air; only use it in dry conditions. Protect it from high humidity, water and snow. Keep it away from high temperatures. Do not subject the device to sudden changes in temperature or heavy vibration as this might damage electronic components. Examine the device for damage before using it. The unit should not be used if it has received an impact or has been damaged in any other way. Please observe national regulations and restrictions. Do not use the device for purposes other than those described in the instructions. This product is not a toy. Keep it out of the reach of children or mentally impaired persons. Any repair or alteration to the device not carried out by the original supplier, will invalidate the warranty or guarantee. The product may only be used by persons who have read and understood these instructions. The device specifications may change without any separate prior notice to this effect.

7. Disposal instructions

Electrical and electronic devices may only be disposed of in accordance with the European WEEE Directive and not with household rubbish. Components must be disposed of or recycled separately as dangerous, toxic elements can inflict sustained damage on the environment if they are disposed of incorrectly. As a consumer, you are bound by the Electrical and Electronic Devices Act (ElektroG) to

return electrical and electronic goods free of charge at the end of their useful life to the manufacturer, the place of purchase or to specially set up, public collection points. The details in each case are governed by national law. The symbol on the product, the operating instructions and/or the packaging refers to these regulations. By separating materials in this way, recycling and disposing of old devices, you are making an important contribution towards protecting our environment. For information on authorised collection points in your area, please contact your local city or municipal administration.

WEEE guideline: 2012/19/EU WEEE register number: DE 67896761

WD Plus GmbH, herewith declares that this product 301777 conforms to the principle requirements and other relevant stipulations. The complete Declaration of Conformity can be obtained from: WD Plus GmbH, Wohlenbergstraße 16, 30179 Hanover

MO-FR 9:30am - 18pm CET

brandson-equipment.de