LZ792CT - Sink SMEG - Free user manual and instructions

Find the device manual for free LZ792CT SMEG in PDF.

SMEG LZ792CT - Sink
📄 42 pages English EN Download 💬 AI Question 10 questions ⚙️ Specs
Notice SMEG LZ792CT - page 6
Pick your language and provide your email: we'll send you a specifically translated version.
Product type Sink
Brand SMEG
Model LZ792CT
Material Non-porous composite (resin and quartz)
Installation type Flush mount or top mount
Number of basins 1
Available finishes Light and dark
Heat resistance Avoid direct contact with hot pans
Impact resistance Avoid accidental impacts
Routine maintenance Clean with a non-abrasive sponge and mild detergent
Descaling Weekly treatment with a suitable descaler
Stubborn stains (light surfaces) Bleach and warm water solution (3/4, 1/4), let stand for 8 hours
Stubborn stains (dark surfaces) Circular rubbing with a soft sponge and detergent
Precautions Do not cut directly on the sink, use a cutting board
Use of boiling liquids Turn on the cold water tap and keep 1 cm of water in the bottom
Warranty Manufacturer's standard warranty (subject to compliance with instructions)
Installation Carried out by a qualified professional, silicone not provided
Initial cleaning Wash with ordinary detergent and a soft sponge before installation
Included accessories None (silicone and cutting board not included)

Frequently Asked Questions - LZ792CT SMEG

How to clean the Smeg LZ792CT sink?
Use a non-abrasive sponge and a mild dish soap. Rinse with warm water and dry with a microfiber cloth. Avoid metal sponges and abrasive products.
What to do about limescale stains?
Apply an anti-corrosion descaler diluted in warm water. Leave for a few minutes, gently rub in a circular motion, rinse and dry. Repeat if necessary.
Can I cut food directly on the sink?
No, this can cause irreparable scratches. Always use a cutting board to protect the surface.
Can I pour boiling water into the sink?
Yes, but first turn on the cold water tap and make sure there is at least 1 cm of water in the bottom to avoid damaging the material.
How to install the Smeg LZ792CT sink?
Installation must be performed by a qualified professional according to current standards. Silicone is not provided. Clean the sink before installation with ordinary detergent.
What to do if stubborn stains persist on light surfaces?
Prepare a solution of bleach and warm water (3/4 + 1/4). Let stand for about 8 hours (preferably overnight), then rinse thoroughly and dry. Repeat 1-2 times if necessary.
How to maintain dark surfaces?
For stubborn stains, rub in circular motions with a soft sponge and mild detergent. Rinse with warm water and dry. Repeat if needed.
What cleaning products to avoid?
Avoid detergents containing alkaline substances or aggressive liquids (ammonia, caustic soda, drain cleaners). Do not use steel wool or abrasive sponges.
What is the warranty for the sink?
The manufacturer's standard warranty applies, provided that cleaning and care instructions are followed. Failure to do so may void it.
How to avoid scratches?
Never cut directly on the sink, use a cutting board. Avoid accidental impacts and do not place hot objects directly on the surface.

User questions about LZ792CT SMEG

0 question about this device. Answer the ones you know or ask your own.

Ask a new question about this device

Your email remains private: it is only used to notify you if someone answers your question.

No questions yet. Be the first to ask one.

Download the instructions for your Sink in PDF format for free! Find your manual LZ792CT - SMEG and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. LZ792CT by SMEG.

USER MANUAL LZ792CT SMEG

SILICONE

Isometric diagram of a device with two stacked plates and directional arrows indicating movement or force (no text or symbols).

LAVELLO TOP

graph TD A["Step 1"] --> B["Central Structure"] C["Step 2"] --> B D["Step 3"] --> B E["Step 4"] --> B F["Step 5"] --> B G["Step 6"] --> B

Diagram of a layered mechanical or electronic component with upward arrows indicating motion or force (no text or symbols).

TOP SILICONE LAVELLO

graph TD A["1"] --> B["2"] C["3"] --> D["4"] E["5"] --> F["6"] G["Bottom Left"] --> H["Bottom Right"] I["Bottom Right"] --> J["Bottom Left"]

Simple line drawing of a hand cleaning a surface with a cloth (no text or symbols).

2. NON-ROUTINE MAINTENANCE

Simple line drawing of a cooking pot with a crossed-out X symbol (no text or labels).

SMEG LZ792CT - NON-ROUTINE MAINTENANCE - 2

Before fitting the sink, it is advisable to wash it using standard dish detergent and a soft sponge to remove any manufacturing residues.

Rinse the sink thoroughly and dry it using a microfibre cloth.

SMEG LZ792CT - NON-ROUTINE MAINTENANCE - 3

STANDARD INSTALLATION

Diagram illustrating a drill bit and screwdriver tool application, showing correct and incorrect states of the process.

SILICONE

Isometric diagram of a device with two stacked plates and directional arrows indicating movement or force (no text or symbols).

SINK TOP

graph TD A["1"] --> B["Central Fold"] C["2"] --> B D["3"] --> B E["4"] --> B F["5"] --> B G["6"] --> B

SMEG LZ792CT - STANDARD INSTALLATION - 6

UNDERMOUNT INSTALLATION

TEMPLATE ① ②

15 mm Ø 11.5 mm

SILICONE

Diagram of a mechanical assembly with two stacked components and upward arrows indicating motion (no text or symbols)

TOP SILICONE SINK

graph TD A["1"] --> B["2"] C["3"] --> D["4"] E["5"] --> F["6"] G["Bottom Left"] --> H["Bottom Right"] I["Bottom Right"] --> J["Bottom Left"]

SMEG LZ792CT - UNDERMOUNT INSTALLATION - 7

The packaging materials (plastic bags, expanded polystyrene, etc.) must not be left within reach of children as they are a potential hazard.

SMEG LZ792CT - UNDERMOUNT INSTALLATION - 8

Installation and support should be undertaken by qualified individuals, in accordance with the applicable legal requirements.

The silicone is not included with the product. The sink shown in this guide is for illustrative purposes only.

SMEG LZ792CT - UNDERMOUNT INSTALLATION - 9

1. ROUTINE MAINTENANCE

Cleaning your Smeg product is quick and simple. Even though the non-porous surface prevents liquids penetrating into the material, it is preferable to remove them immediately using a soft, non-abrasive sponge and standard dish detergent. You should then rinse the surface and dry it carefully using a microfibre cloth.

Simple line drawing of a hand wiping a surface with motion lines (no text or symbols)

2. NON-ROUTINE MAINTENANCE

Cleaning stubborn stains is not difficult: all you need to do is choose the right product and use it correctly.

SMEG LZ792CT - NON-ROUTINE MAINTENANCE - 1

For stubborn stains on LIGHT-COLOURED products, you can use a solution of bleach and warm water (3/4 to 1/4), leaving it to act for eight hours (we recommend that this cleaning be performed during the night). Afterwards, rinse thoroughly and dry the entire surface carefully using a microfibre cloth. If the stains remain, the operation can be repeated one or two more times.

SMEG LZ792CT - NON-ROUTINE MAINTENANCE - 2

For stubborn stains on DARK-COLOURED products, you can remove them directly with a soft, non-abrasive sponge and standard dish detergent, using small circular movements. When finished, rinse using warm water and carefully dry the entire surface using a microfibre cloth. If the stains remain, the operation can be repeated one or two more times.

SMEG LZ792CT - NON-ROUTINE MAINTENANCE - 3

To remove limescale stains, we recommend the use of a non-corrosive descaling product diluted with warm water. Distribute the solution uniformly over the entire surface of the product. Clean with a soft, non-abrasive sponge using small circular movements and leave the product to act for several minutes (follow the instructions and conditions for use on the product label). When finished, rinse using warm water and dry carefully using a microfibre cloth.

Failure to follow the cleaning and maintenance instructions stated in this manual may invalidate the standard warranty provided by the manufacturer.

SMEG LZ792CT - NON-ROUTINE MAINTENANCE - 4

To ensure that there is no change to the characteristics of the product, we recommend that users observe the following precautions:

- dry the surface of the product every day to avoid prolonged exposure to water that could lead to the build-up of limescale or stubborn stains

- do not use detergents that contain alkaline substances and aggressive liquids (such as ammonia, caustic soda or drain cleaners)

- do not remove traces of dirt using steel scourers or abrasive sponges that could damage the surface

- do not cut or chop directly on the surface of the product because this could cause irreparable scratches (always use chopping boards)

- avoid accidental knocks that could cause irreparable micro-damage

- do not place hot cookware, pans or coffee makers directly on the sink surface: stains from discolouration and/or damage could form in areas where hot items are placed

- avoid pouring boiling liquids directly into the sink without first turning on the cold tap and filling the sink with at least 1 cm of water, as this could damage the product

• to prevent the build-up of limescale, it is recommended that a descaling treatment be completed at least once a week. This is recommended in particular for dark-coloured sinks. Fill the tub with warm water and add two spoonfuls of liquid or powder dishwasher detergent or a dishwasher tab. Leave the solution for 5/6 hours. Rinse thoroughly and dry carefully.

Simple line drawing of a crossed-out kitchen counter with no text or symbols

Simple line drawing of a cooking pot with crossed-out kitchen panes (no text or symbols)

SMEG LZ792CT - NON-ROUTINE MAINTENANCE - 7

Do not put pans or coffee makers that have just been taken off the heat (which sometimes reach 500°C) directly into sink.

Diagram illustrating a drill bit and screwdriver tool application, with a magnified view showing the process.

SILICONE

Isometric diagram of a device with two stacked plates and directional arrows indicating movement or force (no text or symbols)

SINK TOP

graph TD A["1"] --> B["Central Structure"] C["2"] --> B D["3"] --> B E["4"] --> B F["5"] --> B G["6"] --> B

SMEG LZ792CT - NON-ROUTINE MAINTENANCE - 13

INSTALLATION SOUS LE PLAN SUPÉRIEUR

1 2 PATTERN

15 mm Ø 11.5 mm

SILICONE

Diagram of a layered mechanical or electronic component with upward arrows indicating motion or force, no text or symbols present.

TOP SILICONE SINK

graph TD A["1"] --> B["2"] C["3"] --> D["4"] E["5"] --> F["6"] G["Bottom Left"] --> H["Bottom Right"] I["Bottom Right"] --> J["Bottom Left"]

Simple line drawing of a hand wiping a surface with motion lines (no text or symbols)

Simple line drawing of a cooking pot with steam rising, crossed by a diagonal line (no text or symbols)

Diagram illustrating a drill bit and screwdriver tool application, with a magnified view showing the process.

SILICONE

Isometric diagram of a device with two stacked plates and directional arrows indicating movement or force (no text or symbols)

SINK WORKTOP

graph TD A["1"] --> B["Object"] C["5"] --> B D["3"] --> B E["4"] --> B F["6"] --> B G["2"] --> B

UNTERBAU-INSTALLATIONSMEG LZ792CT - INSTALLATION SOUS LE PLAN SUPÉRIEUR - 14

TEMPLATE ① ②

15 mm Ø 11.5 mm

SILICONE

Diagram of a mechanical assembly with three stacked components and upward arrows indicating motion (no text or symbols)

WORKTOP SILICONE SINK

graph TD A["①"] --> B["②"] C["③"] --> D["④"] E["⑤"] --> F["⑥"] G["⑦"] --> H["⑧"]

Simple line drawing of a hand cleaning a surface with a cloth (no text or symbols)

Simple line drawing of a cooking pot with crossed-out black X marks (no text or symbols)

Diagram illustrating a drill bit and screwdriver tool application, with a magnified view showing the process.

SILICONE

Isometric diagram of a device with two stacked plates and directional arrows indicating movement or force (no text or symbols)

SINK COUNTERTOP

graph TD A["1"] --> B["Central Object"] C["2"] --> B D["3"] --> B E["4"] --> B F["5"] --> B G["6"] --> B

Diagram of a mechanical assembly with two stacked components and upward arrows indicating motion (no text or symbols)

COUNTERTOP SILICONE SINK

graph TD A["1"] --> B["2"] C["3"] --> D["4"] E["5"] --> F["6"] G["Bottom Left"] --> H["Bottom Right"] I["Bottom Right"] --> J["Bottom Left"]

Simple line drawing of a hand wiping a surface with motion lines (no text or symbols)

Simple line drawing of a cooking pot with a crossed-out X symbol (no text or labels)

Diagram illustrating a drill bit and screwdriver tool application, showing correct and incorrect states of the process.

SILICONE

Isometric diagram of a device with two stacked plates and directional arrows indicating movement or force (no text or symbols)

DISHWASHER COVER

graph TD A["1"] --> B["Object"] C["5"] --> B D["3"] --> B E["4"] --> B F["6"] --> B G["2"] --> B

Diagram of a layered mechanical or electronic component with upward arrows indicating motion or force, no text or symbols present.

COVER SILICONE DISHWASHER

graph TD A["1"] --> B["2"] C["3"] --> D["4"] E["5"] --> F["6"] G["Bottom Left"] --> H["Bottom Right"] I["Bottom Right"] --> J["Bottom Left"]

Simple line drawing of a hand cleaning a surface with a cloth (no text or symbols)

Simple line drawing of a crossed-out kitchen counter with steam rising (no text or symbols)

Diagram illustrating a drill bit and screwdriver tool application, showing correct and incorrect states of the process.

SILICONE

Isometric diagram of a device with two stacked plates and directional arrows indicating movement or force (no text or symbols)

Diagram of a mechanical assembly with two stacked components and upward arrows indicating motion (no text or symbols)

Hand wiping a surface with a cloth (no text or symbols)

2. НЕПЛАНОВЫЙ УХОД

Simple line drawing of a kitchen with a crossed-out black X symbol (no text or labels)

Diagram illustrating a drill bit and screwdriver tool application, showing correct and incorrect states of the process.

SILICONE

Isometric diagram of a device with two stacked plates and directional arrows indicating movement or force (no text or symbols)

SINK COUNTERTOP

graph TD A["①"] --> B["Central Structure"] C["⑤"] --> B D["③"] --> B E["④"] --> B F["⑥"] --> B G["②"] --> B

MONTAŻ POD BLATEMSMEG LZ792CT - НЕПЛАНОВЫЙ УХОД - 7

TEMPLATE ① ②

15 mm Ø 11.5 mm

SILICONE

Diagram of a layered mechanical or electronic component with upward arrows indicating motion or force, no text or symbols present.

BLADE SILICONE DRAIN

graph TD A["①"] --> B["②"] C["③"] --> D["④"] E["⑤"] --> F["⑥"] G["⑦"] --> H["⑧"]

Simple line drawing of a hand cleaning a surface with a cloth (no text or symbols)

2. IMMEDIATE MAINTENANCE

Simple line drawing of a cooking pot with crossed-out kitchen panes (no text or symbols)

Diagram illustrating a drill bit and screwdriver tool application, showing correct/incorrect states of the process.

SILICONE

Isometric diagram of a device with two stacked plates and directional arrows indicating movement or force (no text or symbols)

Diagram of a layered mechanical or electronic component with upward arrows indicating motion or force, no text or symbols present.

SALTCELLAR SILICONE KITCHEN SINK

graph TD A["1"] --> B["2"] C["3"] --> D["4"] E["5"] --> F["6"] G["Bottom Left"] --> H["Bottom Right"] I["Bottom Right"] --> J["Bottom Left"]

Simple line drawing of a hand cleaning a surface with a cloth (no text or symbols)

Simple line drawing of a kitchen with a crossed-out black X symbol (no text or labels)

Diagram illustrating a drill bit and screwdriver tool application process with labeled parts.

Silicone

Isometric diagram of a device with two stacked plates and directional arrows indicating movement or force (no text or symbols).

Diagram of a layered mechanical or electronic component with upward arrows indicating motion or force, no text or symbols present.

Two hand icons with different textures, one covering a cloth and the other covering a surface (no text or symbols).

Simple line drawing of a crossed-out kitchen counter with no text or symbols.

Simple line drawing of a cooking pot with crossed-out black lines (no text or symbols).

SMEG LZ792CT - IMMEDIATE MAINTENANCE - 17

Manual assistant
Powered by Anthropic
Waiting for your message
Product information

Brand : SMEG

Model : LZ792CT

Category : Sink