87 - Sewing machine BERNINA - Free user manual and instructions
Find the device manual for free 87 BERNINA in PDF.
User questions about 87 BERNINA
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Sewing machine in PDF format for free! Find your manual 87 - BERNINA and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. 87 by BERNINA.
USER MANUAL 87 BERNINA
Binder attachment # 87 - # 88
Bandeinfasser # 87 - # 88 | Ourleur simple # 87 - # 88
made to create
BERNINA
You can find further information and the Binder attachment video at www.bernina.com
Language
| Binder attachment # 87 | # 88 en | 4 | |
| Bandeinfasser # 87 | # 88 de | 10 | |
| Ourleur simple # 87 | # 88 fr | 16 | |
| Bandapparaat # 87 | # 88 nl | 22 | |
| Bordatore # 87 | # 88 it | 28 | |
| Ribeteador deCNTas # 87 | # 88 es | 34 | |
| Bandkantare # 87 | # 88 sv | 40 | |
| Kantebängsapparat # 87 | # 88 | da | 46 |
| Båndfeste # 87 | # 88 no | 52 | |
| Esisaumattujen nauhojen nauhareunustaja # 87 | # 88 | fi | 58 |
| Устroyстvo дnia OKаNTовки # 87 | # 88 | ru | 64 |
| Вавлидаурашten# 87、又は# 88 | jp | 70 |
Supplies
1 Binder attachment
1 Black securing screw
1 User instructions
#87
for folded binding of 13 mm/20 mm/25 mm width.
Additionally required
- Presser foot # 951# 95C
Presser foot for office
88
for unfolded binding of 28mm / 32mm/ 38 mm width.
Application
Quick and easy binding of edges with unfolded or pre-folded bias-binding.
For your safety
Before using the accessory please read the instruction manual of the sewing machine and the accessory carefully!
en
Assembly
Use securing screw (1) to fit the binder attachment in such way that the plate sits virtually flush with the stitch plate. This applies for activa, aurora, artista and BERNINA 830 models.
Butt guiding aid (2) against presser foot. Then tighten the screws (4, 5).
Loosen screw (3) on pivot arm and move binder to presser foot as close as possible from the side, then retighten screw (3) provisionally.
Preparation
Move screws (6, 7) to front holes (if not placed there already). Set binder guide parallel with presser foot and, at the same time, binding-exiting channel flush with the stitch plate. Tighten the two screws.
Check binder-/presser-foot position. The binder must be set in such way that the clearance between presser foot and binder guide is just wide enough for them not to interfere with each other.Tighten screw (3).
Sewing machine settings
Presser foot: Presser foot for binder attachment # 95/95C
Stitch: Straight-stitch/zigzag
Stitch width: 0 / 0 - 4mm
Stitch length: 2-3mm
Feed-dog: Sewing position
en
Mode of operation
Insert folded bias-binding into binder, pushing it through the opening with a pointed but soft item (e.g. a toothpick) if required.
Place fabric edge under presser foot, positioning it into the binding so that binding wraps around edge nicely. Set needle position to allow for edge-stitching of the binding.
Baste or neaten quilted or multi-layered fabrics before binding.
Variant
Use zigzag stitch to attach the binding. Set needle position so that one swing of the needle catches the binding and the other the fabric.
TIPP
Use a wider needle distance in curves. Reset needle position accordingly.
en
de
Lieferumfang
Transportor: oppe for sying
Bruk
TpaHcnpTeP: B NOLOXKeHN IJIa WITbI
Yn
PruHUsn pa a som
BCTaBbTe CIOXeHHyI JeHTy B yCTpOiCTBO, IPOdBnHyB ee B 3a3Op YEM-HN6yDb TOHkIM (HaNPmep, 3y6ouchKoJ).
PomeCTNe KpaT KaHn NOJ NaNky TaK, YTO6bI yCTpoiCTBO MOrNo ee XopoSO OKaHTOBaTb.
ПОLOЖЕНUEИГьIДОЛЖHO NO3BOJIArTB BbINOJIHHTb OKaHTOBKy.
KBNIT NIN MHOROCIOHHyTO KaHb LyuUe CMeTaTb NO KpaIO nepeD OKaHTOBKoI.
BapnaHT:
Дя OKaHTOBKMOXHO NcNoJIb3OBAtB CTPOUky 3nΓ-3aI.
YctaHOBIne NIOXKeHne INIbI TaK, YTO6bl IeBbI npOKoN INIbI nonaDAn BTKaHb, a npaBbIM B KaHT.
Cobem
UnpHa cTpoKn DOJXHa 6bITb DOCTaTOUHO UnpOKo, ecn Kpa3akpyIeH. PpH HeO6xOUMOCTN, NOMEHTe NOJoxHe Hrbl.
Copyright by BERNINA International AG 2013
09 034303.51.00
