DO91125 - Freezer DOMO - Free user manual and instructions

USER MANUAL DO91125 DOMO

Reverse Door Tool required: Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner. Ensure the unit is unplugged and empty. To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid so that it will not slip during the door reversing process. All parts removed must be saved to do the reinstallation of the door. Do not lay the unit flat as this may damage the coolant system. It' s better that 2 people handle the unit during assembly.

1. Remove two screws at rear side of top cover.

2. Remove top cover and thermostat knob, then place it aside.

3. Unscrew top hinge and then remove door and place it on a soft pad to

4. Unscrew bottom hinge. Then remove the adjustable feet from both

Reverse Door Tool required: Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner. Ensure the unit is unplugged and empty. To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid so that it will not slip during the door reversing process. All parts removed must be saved to do the reinstallation of the door. Do not lay the unit flat as this may damage the coolant system. It' s better that 2 people handle the unit during assembly.

1. Remove two screws at rear side of top cover.

2. Remove top cover and thermostat knob, then place it aside.

3. Unscrew top hinge and then remove door and place it on a soft pad to

4. Unscrew bottom hinge. Then remove the adjustable feet from both

deur op en plaats deze op een zacht oppervlak om krassen te vermijden. Reverse Door Tool required: Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner. Ensure the unit is unplugged and empty. To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid so that it will not slip during the door reversing process. All parts removed must be saved to do the reinstallation of the door. Do not lay the unit flat as this may damage the coolant system. It' s better that 2 people handle the unit during assembly.

1. Remove two screws at rear side of top cover.

2. Remove top cover and thermostat knob, then place it aside.

3. Unscrew top hinge and then remove door and place it on a soft pad to

4. Unscrew bottom hinge. Then remove the adjustable feet from both

Reverse Door Tool required: Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner. Ensure the unit is unplugged and empty. To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid so that it will not slip during the door reversing process. All parts removed must be saved to do the reinstallation of the door. Do not lay the unit flat as this may damage the coolant system. It' s better that 2 people handle the unit during assembly.

1. Remove two screws at rear side of top cover.

2. Remove top cover and thermostat knob, then place it aside.

3. Unscrew top hinge and then remove door and place it on a soft pad to

4. Unscrew bottom hinge. Then remove the adjustable feet from both

5. Unscrew and remove the bottom hinge pin, turn the bracket over and replace it.

6. Refit the bracket fitting the bottom hinge pin. Replace both adjustable

7. Place the door back on. Ensure the door is aligned horizontally and

vertically, so that the seals are closed on all sides before finally tightening the top hinge.

8. Put the top cover and fix it with 2 screws on the back.

5. Unscrew and remove the bottom hinge pin, turn the bracket over and replace it.

6. Refit the bracket fitting the bottom hinge pin. Replace both adjustable

7. Place the door back on. Ensure the door is aligned horizontally and

vertically, so that the seals are closed on all sides before finally tightening the top hinge.

8. Put the top cover and fix it with 2 screws on the back.

5. Unscrew and remove the bottom hinge pin, turn the bracket over and replace it.

6. Refit the bracket fitting the bottom hinge pin. Replace both adjustable

7. Place the door back on. Ensure the door is aligned horizontally and

vertically, so that the seals are closed on all sides before finally tightening the top hinge.

8. Put the top cover and fix it with 2 screws on the back.

5. Unscrew and remove the bottom hinge pin, turn the bracket over and replace it.

6. Refit the bracket fitting the bottom hinge pin. Replace both adjustable

7. Place the door back on. Ensure the door is aligned horizontally and

vertically, so that the seals are closed on all sides before finally tightening the top hinge.

8. Put the top cover and fix it with 2 screws on the back.

Temperature setting recommendation: 4°C is recommended. Under recommended setting, the best storage time of freezer is no more than 3 days. The best storage time may reduce under other settings.

Temperature setting recommendation: 4°C is recommended. Under recommended setting, the best storage time of freezer is no more than 3 days. The best storage time may reduce under other settings.

Reverse Door Tool required: Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner. Ensure the unit is unplugged and empty. To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid so that it will not slip during the door reversing process. All parts removed must be saved to do the reinstallation of the door. Do not lay the unit flat as this may damage the coolant system. It' s better that 2 people handle the unit during assembly.

1. Remove two screws at rear side of top cover.

2. Remove top cover and thermostat knob, then place it aside.

3. Unscrew top hinge and then remove door and place it on a soft pad to

4. Unscrew bottom hinge. Then remove the adjustable feet from both

2. Retirez le couvercle supérieur.

Reverse Door Tool required: Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner. Ensure the unit is unplugged and empty. To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid so that it will not slip during the door reversing process. All parts removed must be saved to do the reinstallation of the door. Do not lay the unit flat as this may damage the coolant system. It' s better that 2 people handle the unit during assembly.

1. Remove two screws at rear side of top cover.

2. Remove top cover and thermostat knob, then place it aside.

3. Unscrew top hinge and then remove door and place it on a soft pad to

4. Unscrew bottom hinge. Then remove the adjustable feet from both

placez-la sur une surface rembourrée pour éviter qu’elle ne se raye. Reverse Door Tool required: Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner. Ensure the unit is unplugged and empty. To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid so that it will not slip during the door reversing process. All parts removed must be saved to do the reinstallation of the door. Do not lay the unit flat as this may damage the coolant system. It' s better that 2 people handle the unit during assembly.

1. Remove two screws at rear side of top cover.

2. Remove top cover and thermostat knob, then place it aside.

3. Unscrew top hinge and then remove door and place it on a soft pad to

4. Unscrew bottom hinge. Then remove the adjustable feet from both

Reverse Door Tool required: Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner. Ensure the unit is unplugged and empty. To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid so that it will not slip during the door reversing process. All parts removed must be saved to do the reinstallation of the door. Do not lay the unit flat as this may damage the coolant system. It' s better that 2 people handle the unit during assembly.

1. Remove two screws at rear side of top cover.

2. Remove top cover and thermostat knob, then place it aside.

3. Unscrew top hinge and then remove door and place it on a soft pad to

4. Unscrew bottom hinge. Then remove the adjustable feet from both

5. Unscrew and remove the bottom hinge pin, turn the bracket over and replace it.

6. Refit the bracket fitting the bottom hinge pin. Replace both adjustable

7. Place the door back on. Ensure the door is aligned horizontally and

vertically, so that the seals are closed on all sides before finally tightening the top hinge.

8. Put the top cover and fix it with 2 screws on the back.

5. Unscrew and remove the bottom hinge pin, turn the bracket over and replace it.

6. Refit the bracket fitting the bottom hinge pin. Replace both adjustable

7. Place the door back on. Ensure the door is aligned horizontally and

vertically, so that the seals are closed on all sides before finally tightening the top hinge.

8. Put the top cover and fix it with 2 screws on the back.

5. Unscrew and remove the bottom hinge pin, turn the bracket over and replace it.

6. Refit the bracket fitting the bottom hinge pin. Replace both adjustable

7. Place the door back on. Ensure the door is aligned horizontally and

vertically, so that the seals are closed on all sides before finally tightening the top hinge.

8. Put the top cover and fix it with 2 screws on the back.

5. Unscrew and remove the bottom hinge pin, turn the bracket over and replace it.

6. Refit the bracket fitting the bottom hinge pin. Replace both adjustable

7. Place the door back on. Ensure the door is aligned horizontally and

vertically, so that the seals are closed on all sides before finally tightening the top hinge.

8. Put the top cover and fix it with 2 screws on the back.

Temperature setting recommendation: 4°C is recommended. Under recommended setting, the best storage time of freezer is no more than 3 days. The best storage time may reduce under other settings.

Temperature setting recommendation: 4°C is recommended. Under recommended setting, the best storage time of freezer is no more than 3 days. The best storage time may reduce under other settings.

Reverse Door Tool required: Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner. Ensure the unit is unplugged and empty. To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid so that it will not slip during the door reversing process. All parts removed must be saved to do the reinstallation of the door. Do not lay the unit flat as this may damage the coolant system. It' s better that 2 people handle the unit during assembly.

1. Remove two screws at rear side of top cover.

2. Remove top cover and thermostat knob, then place it aside.

3. Unscrew top hinge and then remove door and place it on a soft pad to

4. Unscrew bottom hinge. Then remove the adjustable feet from both

Reverse Door Tool required: Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner. Ensure the unit is unplugged and empty. To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid so that it will not slip during the door reversing process. All parts removed must be saved to do the reinstallation of the door. Do not lay the unit flat as this may damage the coolant system. It' s better that 2 people handle the unit during assembly.

1. Remove two screws at rear side of top cover.

2. Remove top cover and thermostat knob, then place it aside.

3. Unscrew top hinge and then remove door and place it on a soft pad to

4. Unscrew bottom hinge. Then remove the adjustable feet from both

hält. Heben Sie die Tür hoch und legen Sie diese zur Vermeidung von Kratzern auf inen weichen Untergrund. Reverse Door Tool required: Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner. Ensure the unit is unplugged and empty. To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid so that it will not slip during the door reversing process. All parts removed must be saved to do the reinstallation of the door. Do not lay the unit flat as this may damage the coolant system. It' s better that 2 people handle the unit during assembly.

1. Remove two screws at rear side of top cover.

2. Remove top cover and thermostat knob, then place it aside.

3. Unscrew top hinge and then remove door and place it on a soft pad to

4. Unscrew bottom hinge. Then remove the adjustable feet from both

Reverse Door Tool required: Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner. Ensure the unit is unplugged and empty. To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid so that it will not slip during the door reversing process. All parts removed must be saved to do the reinstallation of the door. Do not lay the unit flat as this may damage the coolant system. It' s better that 2 people handle the unit during assembly.

1. Remove two screws at rear side of top cover.

2. Remove top cover and thermostat knob, then place it aside.

3. Unscrew top hinge and then remove door and place it on a soft pad to

4. Unscrew bottom hinge. Then remove the adjustable feet from both

5. Unscrew and remove the bottom hinge pin, turn the bracket over and replace it.

6. Refit the bracket fitting the bottom hinge pin. Replace both adjustable

7. Place the door back on. Ensure the door is aligned horizontally and

vertically, so that the seals are closed on all sides before finally tightening the top hinge.

8. Put the top cover and fix it with 2 screws on the back.

5. Unscrew and remove the bottom hinge pin, turn the bracket over and replace it.

6. Refit the bracket fitting the bottom hinge pin. Replace both adjustable

7. Place the door back on. Ensure the door is aligned horizontally and

vertically, so that the seals are closed on all sides before finally tightening the top hinge.

8. Put the top cover and fix it with 2 screws on the back.

5. Unscrew and remove the bottom hinge pin, turn the bracket over and replace it.

6. Refit the bracket fitting the bottom hinge pin. Replace both adjustable

7. Place the door back on. Ensure the door is aligned horizontally and

vertically, so that the seals are closed on all sides before finally tightening the top hinge.

8. Put the top cover and fix it with 2 screws on the back.

5. Unscrew and remove the bottom hinge pin, turn the bracket over and replace it.

6. Refit the bracket fitting the bottom hinge pin. Replace both adjustable

7. Place the door back on. Ensure the door is aligned horizontally and

vertically, so that the seals are closed on all sides before finally tightening the top hinge.

8. Put the top cover and fix it with 2 screws on the back.

Temperature setting recommendation: 4°C is recommended. Under recommended setting, the best storage time of freezer is no more than 3 days. The best storage time may reduce under other settings.

Temperature setting recommendation: 4°C is recommended. Under recommended setting, the best storage time of freezer is no more than 3 days. The best storage time may reduce under other settings.

WARRANTY Dear client , All of our products are always submitted to a strict quality control before they are sold to you. Should you nevertheless experience problems with your device, we sincerely regret this. In that case, we kindly request you to contact our customer service. Our sta will gladly assist you. [phone] [e-mail] Monday – Thursday: 8.30 – 12.00 and 13.00 – 17.00 Friday: 8.30 – 12.00 and 13.00 – 16.30 This appliance has a two year warranty period. During this period the manufacturer is responsible for any failures that are the direct result of construction failure. When these failures occur the appliance will be repaired or replaced if necessary. The warranty will not be valid when the damage to the appliance is caused by wrong use, not following the instructions or repairs executed by a third party. The guarantee is issued with the original till receipt. All parts, which are subject to wear, are excluded from the warranty. If your device breaks down within the 2-year warranty period, you can return the device together with your receipt to the shop where you purchased it. The guarantee on accessories and components that are liable to wear-and-tear is only 6 months. The guarantee and responsibility of the supplier and manufacturer lapse automatically in the following cases:

• If the instructions in this manual have not been followed.

• In case of incorrect connection, e.g. electrical voltage that is too high.

• In case of incorrect, rough or abnormal use.

• In case of insucient or incorrect maintenance.

• In case of repairs or alterations to the device by the consumer or non-authorised third parties.

• If the customer used parts or accessories that are not recommended or provided by the supplier / manufacturer. SAFETY INSTRUCTIONS When using electrical appliances, basic safety precautions should always be taken, including the following:

• Read all instructions carefully. Keep this manual for future reference.

• Make sure all packaging materials and promotional stickers have been removed before using the appliance for the rst time. Make sure children cannot play with the packaging materials.

• This appliance is intended to be used in household and similar applications such as:

• sta kitchen areas in shops, oces and other working environments;44 DO91125

• by clients in hotels, motels and other residential type environments;

• bed and breakfast type environments.

• Children should be supervised to ensure that they do not play with the appliance.

• This appliance can be used by children aged from 16 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.

• Children shall not play with the appliance.

• Cleaning and user maintenance shall not be made by children unless they are older than 16 or supervised.

• Keep the appliance and its cord out of reach of children younger than 16 years.

• All repairs should be carried out by the manufacturer or its aftersales service.

• Make sure that children do not touch the cord or appliance.

• Your appliance uses isobutane (R600a) as a refrigerant. Despite the fact that R600a is an environmentally friendly and natural gas, it is highly ammable. Therefore you should be careful during shipment and installation to prevent your appliance’s cooler elements from being damaged. In the event of a leak caused by damage to the cooler elements, move your refrigerator from open ames or heat sources and ventilate the room where the appliance is located for a few minutes.

I ELECTRICAL WARNINGS

• Attention: This appliance cannot be used with an external timer or a separate remote control.

• Before use, check carefully that the electric tension and frequency of the power net at your home match the indications on the rating label of the appliance.

• The appliance must be plugged into an appropriate outlet that is installed and grounded in accordance with local installation regulations.

• Never use the appliance when the cord or plug is damaged, after malfunction or when the appliance itself is damaged. In that case, take the appliance to the nearest qualied service center for check-up and repair.

• It is prohibited to alter or modify the device and its specications.

• When disposing of the appliance, remove the plug from the power socket, cut the power cord (as closely as possible to the appliance), and remove the door to prevent playing children getting an electrical shock or shutting themselves in the appliance.

• The lamp in the appliance is intended for use in this cooling device only. Do not use the lamp as a household light.

• Unplug the appliance when it is not in use, before assembling or disassembling any parts and before cleaning the appliance. Put all buttons and knobs into the ‘o’ position and unplug the appliance by grasping the plug. Never unplug by pulling the cord. I INSTALLATION

• Never place this appliance near a gas stove or electrical stove or in a place where it may come into contact with a warm appliance.

• Always use the appliance on a steady, dry and level surface.

• Keep the cord away from sharp edges and hot parts or other heat sources.

• Keep the ventilation openings free of obstructions.

• The appliance may not be used with an extension lead or a multiple socket.

• Avoid long exposure to direct sunlight.

• Make sure that you have access to the plug of the appliance.

• Make sure the plug and cord are not crushed or damaged by the back of the appliance. This can cause short circuits and, as a result, overheating and re.

• This is a heavy appliance. Be careful when moving it.

• This cooling unit is not intended for use as a built-in appliance.

• Do not place a power strip or other portable power supply behind the appliance.

• After installation, it is advisable to wait 24 hours before connecting the appliance to allow the oil to ow back in the compressor.46 DO91125

• Do not use the appliance outdoors.

• Only use the appliance for its intended use.

• Only use the appliance for domestic use. The manufacturer can not be held responsible for accidents that result from improper use of the appliance or not following the instructions described in this manual.

• Do not use any other electrical appliance inside the refrigerator, unless they are approved for this purpose by the manufacturer.

• Do not keep any explosive substances inside the appliance, like for instance aerosol cans with a ammable propellant.

• Do not use the appliance without a lamp.

• The use of accessories that are not recommended or sold by the manufacturer can cause re, electrical shock or injuries.

• Ensure the food in the appliance does not touch the back wall.

• Follow the instructions below to prevent contamination of food:

• Keeping the door open for long periods may cause the temperature in the compartments of the appliance to rise considerably.

• Clean the surfaces that could come into contact with food regularly.

• If the appliance is left empty for longer periods, it should be turned o, defrosted and cleaned. Allow it to dry and leave the door ajar to prevent mould from growing in the appliance.

I CLEANING AND MAINTENANCE

• Never immerse the appliance, the cord or the plug in water or any other liquid.

• Do not place warm or hot objects on top of the appliance.

• Do not clean the appliance with anything made of metal.

• Make sure that the refrigerant circuit does not get damaged, for instance during transportation or installation.

• Do not use mechanical appliances or other means to speed up the defrosting process, unless approved by the manufacturer.47 DO91125 www.domo-elektro.be

• WARNING! Never place this appliance on or in the neighbourhood of a gas or electric re or in a place where it could come into contact with a heat source. There are ammable materials located on the back of the appliance.

• Pay attention to the symbol ‘Fire risk – ammable materials’ located on the back of the appliance.

• Remove the exterior and interior packing, wipe the outside thoroughly with a soft dry cloth and the inside with a wet, lukewarm cloth. Dry the appliance o well.

• Let air circulate freely around the cabinet.

• Make sure there is sucient space to open the door.

• This cooling unit is not intended for use as a built-in appliance.

• Select a place with a strong, level oor.

• Avoid direct sunlight and heat. Direct sunlight may aect the acrylic coating. Heat sources nearby will cause higher electricity consumption.

• Avoid very moist places. Too much moisture in the air will cause frost to form very quickly on the evaporator, and your refrigerator.

• Before connecting your refrigerator to the power supply, check that the voltage stated on the rating label of your appliance corresponds to the voltage in your home. A dierent voltage could damage the appliance.

• After installation, leave the fridge for 24 hours before turning it on. This way the refrigerant can settle.

• Allow the appliance to run empty for 8 hours so the compartment can cool to the appropriate temperature.

• One can level the appliance using the adjustable legs. The adjustable legs can be adjusted by screwing them in or out of the appliance. Lift Lower

• The climate class indicates the minimum and maximum ambient temperature for the proper operation of an appliance. You can nd the climate class on the type plate on the back of the appliance.

• SN: Subnormal: ambient temperature between 10°C and 32°C

• N: Normal: ambient temperature between 16°C and 32°C

• ST: Subtropical: ambient temperature between 16°C and 38°C

• T: Tropical: ambient temperature between 16°C and 43°C DOOR CONVERSION If you need to hinge your door on the opposite side, it is recommended that you call your local authorised service agent to make this conversion or ask a technician. Before you reverse the door, you should ensure the appliance is unplugged and empty. After reversing the door, leave the appliance alone for 8 hours before switching it on. This allows the coolant to set.

1. Remove the screws on the back of the top cover.

Reverse Door Tool required: Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner. Ensure the unit is unplugged and empty. To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid so that it will not slip during the door reversing process. All parts removed must be saved to do the reinstallation of the door. Do not lay the unit flat as this may damage the coolant system. It' s better that 2 people handle the unit during assembly.

1. Remove two screws at rear side of top cover.

2. Remove top cover and thermostat knob, then place it aside.

3. Unscrew top hinge and then remove door and place it on a soft pad to

4. Unscrew bottom hinge. Then remove the adjustable feet from both

2. Remove the top cover.

Reverse Door Tool required: Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner. Ensure the unit is unplugged and empty. To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid so that it will not slip during the door reversing process. All parts removed must be saved to do the reinstallation of the door. Do not lay the unit flat as this may damage the coolant system. It' s better that 2 people handle the unit during assembly.

1. Remove two screws at rear side of top cover.

2. Remove top cover and thermostat knob, then place it aside.

3. Unscrew top hinge and then remove door and place it on a soft pad to

4. Unscrew bottom hinge. Then remove the adjustable feet from both

3. Remove the three screws and then remove the top hinge that holds the door in place. Lift the door

and place it on a padded surface to prevent it from being scratched. Reverse Door Tool required: Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner. Ensure the unit is unplugged and empty. To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid so that it will not slip during the door reversing process. All parts removed must be saved to do the reinstallation of the door. Do not lay the unit flat as this may damage the coolant system. It' s better that 2 people handle the unit during assembly.

1. Remove two screws at rear side of top cover.

2. Remove top cover and thermostat knob, then place it aside.

3. Unscrew top hinge and then remove door and place it on a soft pad to

4. Unscrew bottom hinge. Then remove the adjustable feet from both

4. Remove the bottom screw, hinge bracket and adjustable feet from the bottom of the appliance.

Reverse Door Tool required: Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner. Ensure the unit is unplugged and empty. To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid so that it will not slip during the door reversing process. All parts removed must be saved to do the reinstallation of the door. Do not lay the unit flat as this may damage the coolant system. It' s better that 2 people handle the unit during assembly.

1. Remove two screws at rear side of top cover.

2. Remove top cover and thermostat knob, then place it aside.

3. Unscrew top hinge and then remove door and place it on a soft pad to

4. Unscrew bottom hinge. Then remove the adjustable feet from both

5. Take the hinge pin out of the hinge bracket. Turn the bracket around and tighten the pin again.

5. Unscrew and remove the bottom hinge pin, turn the bracket over and replace it.

6. Refit the bracket fitting the bottom hinge pin. Replace both adjustable

7. Place the door back on. Ensure the door is aligned horizontally and

vertically, so that the seals are closed on all sides before finally tightening the top hinge.

8. Put the top cover and fix it with 2 screws on the back.

6. Attach the screws and hinge bracket to the opposite side of the bottom. Put the adjustable feet

5. Unscrew and remove the bottom hinge pin, turn the bracket over and replace it.

6. Refit the bracket fitting the bottom hinge pin. Replace both adjustable

7. Place the door back on. Ensure the door is aligned horizontally and

vertically, so that the seals are closed on all sides before finally tightening the top hinge.

8. Put the top cover and fix it with 2 screws on the back.

7. Carefully set the door back into place. Ensure the door is aligned horizontally and vertically so that

the seals are closed on all sides before nally tightening the top hinge. Insert the hinge back and screw it to the top of the appliance.

5. Unscrew and remove the bottom hinge pin, turn the bracket over and replace it.

6. Refit the bracket fitting the bottom hinge pin. Replace both adjustable

7. Place the door back on. Ensure the door is aligned horizontally and

vertically, so that the seals are closed on all sides before finally tightening the top hinge.

8. Put the top cover and fix it with 2 screws on the back.

8. Put the top cover back and x it in place with the screws.

5. Unscrew and remove the bottom hinge pin, turn the bracket over and replace it.

6. Refit the bracket fitting the bottom hinge pin. Replace both adjustable

7. Place the door back on. Ensure the door is aligned horizontally and

vertically, so that the seals are closed on all sides before finally tightening the top hinge.

8. Put the top cover and fix it with 2 screws on the back.

9. Remove the rubber seal from the door, turn it over, and then put it back on.51

DO91125www.domo-elektro.be

USE TEMPERATURE CONTROLThe fridge is controlled with a temperature control knob located inside the appliance.Adjust the control knob as desired to suit your individual preference. The higher the number, the colder the temperature. Position 4 is the recommended position for normal use.

• In the 0 position the appliance does not operate (the cooling system is switched o), but power supply is not interrupted.
• The running time and temperature are aected by where the fridge is located, how often the door is opened and the temperature of the room the fridge is located in.STORAGE GUIDEFor the best storage, set up your refrigerating appliance as follows:Refrigerator compartment Type of foodDoor rack · Food with natural preservatives such as jams, juices, drinks, spices, etc. · Do not store food with a limited shelf life hereCrisper drawer · Fruits, herbs, and vegetables · Do not refrigerate bananas, onions, potatoes, or garlicMiddle shelf Dairy and eggsTop shelf Food that does not need to be cooked, such as ready-made meals, leftovers, spreads, etc.MOVING THE SHELVES AND DOOR RACK · Empty the fridge before moving the shelves or the door racks. · To move a shelf, raise it and pull it towards you. · To move a door rack, grip it rmly with 2 hands. Raise the door rack and pull it towards you.LIGHTINGBeware: Unplug the appliance from the power supply before replacing the light bulb.1. Remove the bulb cover.2. Unscrew the old bulb and then screw a new 10 W (E14 base) bulb.3. Replace the bulb cover.

Temperature setting recommendation: 4°C is recommended. Under recommended setting, the best storage time of freezer is no more than 3 days. The best storage time may reduce under other settings.

Temperature setting recommendation: 4°C is recommended. Under recommended setting, the best storage time of freezer is no more than 3 days. The best storage time may reduce under other settings.

MOVING YOUR APPLIANCE

If the appliance is turned o for any reason, wait for 10 minutes before turning it back on. This will allow the refrigeration system pressures to equalise before restarting.

• Turn o the appliance and unplug it from the mains socket. Remove all food. Also remove all mobile parts (shelves, accessories, etc.) or x them into the fridge to avoid any shock.

• Relocate and install. If the appliance has been left on its side for any length of time, leave it standing upright for at least 10 minutes before turning on.

STORING FOOD IN THE FRIDGE

The fridge helps to extend the storage times of fresh perishable foods. Fresh food care for best results:

• Store foods that are very fresh and of good quality.

• Ensure that food is well wrapped or covered before it is stored. This will prevent food from dehydrating, deteriorating in colour or losing taste and will help maintain freshness. It will also prevent odour transfer.

• Make sure that strong smelling foods are wrapped or covered and stored away from foods such as butter, milk and cream which can be tainted by strong odours.

• Cool hot foods down before placing them in the fridge. VACATION TIME For short vacation periods, leave the control knobs at their usual settings. During longer absences:

• Disconnect from electrical outlet.

• Clean the refrigerator thoroughly, including defrost pan.

• Leave the door open to avoid possible formations of condensate, mould or odours. POWER FAILURE Most power failures are corrected within an hour or two and will not aect your refrigerator temperatures. However, you should minimize the number of door openings while the power is o. During power failures of longer duration, take steps to protect your food by putting dry ice on top of packages. SOME IMPORTANT RULES FOR THE CORRECT USE OF THE REFRIGERATOR

• Never place hot foods in the refrigerator.

• Beverages should be stored in sealed containers.

• Foods to be stored for a long time should be wrapped in cellophane or polyethylene foil, or kept in glass containers.

• Never place spoiled foods in the cabinet.

• Caution: please keep the products away from re or similar glowing substances before you dispose of the refrigerator.

• Caution: Not for outer camping use (e.g. in a tent).

• Caution: For indoor use only.

• Caution: The appliance can not be used in public transportation.53 DO91125 www.domo-elektro.be

• Keep all accessories, such as shelves, door racks, and drawers, in the appliance to minimise energy consumption.

• Please read the storage instructions on the food packaging. Always check the storage date.

• An empty fridge consumes more energy. After all, when the door is opened, warm air enters the space and needs to be cooled. More air enters when there are fewer products, meaning that more energy needs to be consumed to cool that air. So ll your fridge properly or choose a model sized for your needs.

CLEANING AND MAINTENANCE

• Do not use abrasive cleaning agents or solvents.

• Turn the appliance o. Disconnect the mains plug from the mains socket.

• Take out the food and store in a cool location.

• Clean the appliance with a soft cloth, warm water and detergent.

• Wipe the door seal with clear water only and then wipe dry thoroughly.

• After cleaning, put the plug in the socket and set the desired temperature.

• Put the food back into the appliance.

DEFROSTING THE REFRIGERATOR

The refrigerator defrosts fully automatically. While the cooling is running, beads of condensation or hoarfrost form at the back of the refrigerator. This is normal. It is not necessary to wipe o the condensation or frost. The rear panel defrosts automatically. The condensation runs into the condensation channel and is conveyed to the compressor from where it evaporates. Note: Keep the condensation channel and drainage hole clean, so that the condensation can run out.

DEFROSTING THE FREEZER

A layer of frost in the freezer will impair refrigeration of the frozen food and increases power consumption. Remove the layer of frost regularly. Do not scrape o frost or ice with a knife or pointed object. Doing this may damage the refrigerant tubes.

1. Remove the frozen food and place temporarily in a cool location.

2. Disconnect the appliance from the mains socket.

3. To accelerate the defrosting process, place a pan of hot water on a stand in the freezer.

4. Wipe up condensation with a cloth or sponge.

5. Wipe dry the freezer compartment.

6. Plug in the appliance and adjust the temperature control knob as desired.

7. Put the frozen food back in the freezer.54

TROUBLE SHOOTING Frequently, a problem is minor and a service call may not be necessary, use this trouble shooting guide for a possible solution. Does not work

• Check connection of power cord to power source.

• Check that the temperature controller is not in the 0 position.

• Use proper voltage. Cools too frequently

• The temperature setting is too cool.

• Close door securely.

• Be sure that food is cool before inserting.

• Do not keep door open for too long and minimize door openings.

• Do not place unit close to heat sources or direct sunlight. Internal temperature not cold enough

• Check connection of power cord to power source.

• Check setting and adjust as needed.

• Close door securely.

• Be sure that food is cool before inserting.

• Do not keep door open for too long and minimize door openings.

• Allow room for air to circulate around unit.

• Do not place unit close to heat sources or direct sunlight. Unusual sounds

• The appliance is not level. Readjust the adjusting feet and level the unit.

• The unit is touching a wall or another object. Gently move the appliance. There is water on the oor.

• The condensation duct is blocked. See the chapter on cleaning.

• Too much condensation has formed in the fridge, causing the reservoir to overow. Too much condensation is caused by a heat dierence. Is the door closed properly? Have you put hot food in the fridge? Does the seal still close properly? The door does not close properly.

• The door seal is deformed. Heat it gently using a hairdryer. The rubber seal will become exible and the magnetic strip in the rubber will automatically pull towards the appliance. After cooling, the rubber stays in that position.55 DO91125 www.domo-elektro.be

ENVIRONMENTAL GUIDELINES This symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it must be brought to the applicable collection point for recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city oce, your household waste disposal service or the shop where you purchased the product. The packaging is recyclable. Please treat the packaging ecologically.56 DO91125

Reverse Door Tool required: Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner. Ensure the unit is unplugged and empty. To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid so that it will not slip during the door reversing process. All parts removed must be saved to do the reinstallation of the door. Do not lay the unit flat as this may damage the coolant system. It' s better that 2 people handle the unit during assembly.

1. Remove two screws at rear side of top cover.

2. Remove top cover and thermostat knob, then place it aside.

3. Unscrew top hinge and then remove door and place it on a soft pad to

4. Unscrew bottom hinge. Then remove the adjustable feet from both

2. Retire la tapa superior.

Reverse Door Tool required: Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner. Ensure the unit is unplugged and empty. To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid so that it will not slip during the door reversing process. All parts removed must be saved to do the reinstallation of the door. Do not lay the unit flat as this may damage the coolant system. It' s better that 2 people handle the unit during assembly.

1. Remove two screws at rear side of top cover.

2. Remove top cover and thermostat knob, then place it aside.

3. Unscrew top hinge and then remove door and place it on a soft pad to

4. Unscrew bottom hinge. Then remove the adjustable feet from both

Levante la puerta y colóquela sobre una supercie suave para evitar arañazos. Reverse Door Tool required: Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner. Ensure the unit is unplugged and empty. To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid so that it will not slip during the door reversing process. All parts removed must be saved to do the reinstallation of the door. Do not lay the unit flat as this may damage the coolant system. It' s better that 2 people handle the unit during assembly.

1. Remove two screws at rear side of top cover.

2. Remove top cover and thermostat knob, then place it aside.

3. Unscrew top hinge and then remove door and place it on a soft pad to

4. Unscrew bottom hinge. Then remove the adjustable feet from both

aparato. Reverse Door Tool required: Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner. Ensure the unit is unplugged and empty. To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid so that it will not slip during the door reversing process. All parts removed must be saved to do the reinstallation of the door. Do not lay the unit flat as this may damage the coolant system. It' s better that 2 people handle the unit during assembly.

1. Remove two screws at rear side of top cover.

2. Remove top cover and thermostat knob, then place it aside.

3. Unscrew top hinge and then remove door and place it on a soft pad to

4. Unscrew bottom hinge. Then remove the adjustable feet from both

5. Unscrew and remove the bottom hinge pin, turn the bracket over and replace it.

6. Refit the bracket fitting the bottom hinge pin. Replace both adjustable

7. Place the door back on. Ensure the door is aligned horizontally and

vertically, so that the seals are closed on all sides before finally tightening the top hinge.

8. Put the top cover and fix it with 2 screws on the back.

5. Unscrew and remove the bottom hinge pin, turn the bracket over and replace it.

6. Refit the bracket fitting the bottom hinge pin. Replace both adjustable

7. Place the door back on. Ensure the door is aligned horizontally and

vertically, so that the seals are closed on all sides before finally tightening the top hinge.

8. Put the top cover and fix it with 2 screws on the back.

5. Unscrew and remove the bottom hinge pin, turn the bracket over and replace it.

6. Refit the bracket fitting the bottom hinge pin. Replace both adjustable

7. Place the door back on. Ensure the door is aligned horizontally and

vertically, so that the seals are closed on all sides before finally tightening the top hinge.

8. Put the top cover and fix it with 2 screws on the back.

5. Unscrew and remove the bottom hinge pin, turn the bracket over and replace it.

6. Refit the bracket fitting the bottom hinge pin. Replace both adjustable

7. Place the door back on. Ensure the door is aligned horizontally and

vertically, so that the seals are closed on all sides before finally tightening the top hinge.

8. Put the top cover and fix it with 2 screws on the back.

Temperature setting recommendation: 4°C is recommended. Under recommended setting, the best storage time of freezer is no more than 3 days. The best storage time may reduce under other settings.

Temperature setting recommendation: 4°C is recommended. Under recommended setting, the best storage time of freezer is no more than 3 days. The best storage time may reduce under other settings.

Reverse Door Tool required: Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner. Ensure the unit is unplugged and empty. To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid so that it will not slip during the door reversing process. All parts removed must be saved to do the reinstallation of the door. Do not lay the unit flat as this may damage the coolant system. It' s better that 2 people handle the unit during assembly.

1. Remove two screws at rear side of top cover.

2. Remove top cover and thermostat knob, then place it aside.

3. Unscrew top hinge and then remove door and place it on a soft pad to

4. Unscrew bottom hinge. Then remove the adjustable feet from both

Reverse Door Tool required: Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner. Ensure the unit is unplugged and empty. To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid so that it will not slip during the door reversing process. All parts removed must be saved to do the reinstallation of the door. Do not lay the unit flat as this may damage the coolant system. It' s better that 2 people handle the unit during assembly.

1. Remove two screws at rear side of top cover.

2. Remove top cover and thermostat knob, then place it aside.

3. Unscrew top hinge and then remove door and place it on a soft pad to

4. Unscrew bottom hinge. Then remove the adjustable feet from both

su una supercie morbida per evitare graature Reverse Door Tool required: Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner. Ensure the unit is unplugged and empty. To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid so that it will not slip during the door reversing process. All parts removed must be saved to do the reinstallation of the door. Do not lay the unit flat as this may damage the coolant system. It' s better that 2 people handle the unit during assembly.

1. Remove two screws at rear side of top cover.

2. Remove top cover and thermostat knob, then place it aside.

3. Unscrew top hinge and then remove door and place it on a soft pad to

4. Unscrew bottom hinge. Then remove the adjustable feet from both

Reverse Door Tool required: Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner. Ensure the unit is unplugged and empty. To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid so that it will not slip during the door reversing process. All parts removed must be saved to do the reinstallation of the door. Do not lay the unit flat as this may damage the coolant system. It' s better that 2 people handle the unit during assembly.

1. Remove two screws at rear side of top cover.

2. Remove top cover and thermostat knob, then place it aside.

3. Unscrew top hinge and then remove door and place it on a soft pad to

4. Unscrew bottom hinge. Then remove the adjustable feet from both

5. Unscrew and remove the bottom hinge pin, turn the bracket over and replace it.

6. Refit the bracket fitting the bottom hinge pin. Replace both adjustable

7. Place the door back on. Ensure the door is aligned horizontally and

vertically, so that the seals are closed on all sides before finally tightening the top hinge.

8. Put the top cover and fix it with 2 screws on the back.

5. Unscrew and remove the bottom hinge pin, turn the bracket over and replace it.

6. Refit the bracket fitting the bottom hinge pin. Replace both adjustable

7. Place the door back on. Ensure the door is aligned horizontally and

vertically, so that the seals are closed on all sides before finally tightening the top hinge.

8. Put the top cover and fix it with 2 screws on the back.

5. Unscrew and remove the bottom hinge pin, turn the bracket over and replace it.

6. Refit the bracket fitting the bottom hinge pin. Replace both adjustable

7. Place the door back on. Ensure the door is aligned horizontally and

vertically, so that the seals are closed on all sides before finally tightening the top hinge.

8. Put the top cover and fix it with 2 screws on the back.

5. Unscrew and remove the bottom hinge pin, turn the bracket over and replace it.

6. Refit the bracket fitting the bottom hinge pin. Replace both adjustable

7. Place the door back on. Ensure the door is aligned horizontally and

vertically, so that the seals are closed on all sides before finally tightening the top hinge.

8. Put the top cover and fix it with 2 screws on the back.

Temperature setting recommendation: 4°C is recommended. Under recommended setting, the best storage time of freezer is no more than 3 days. The best storage time may reduce under other settings.

Temperature setting recommendation: 4°C is recommended. Under recommended setting, the best storage time of freezer is no more than 3 days. The best storage time may reduce under other settings.

Reverse Door Tool required: Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner. Ensure the unit is unplugged and empty. To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid so that it will not slip during the door reversing process. All parts removed must be saved to do the reinstallation of the door. Do not lay the unit flat as this may damage the coolant system. It' s better that 2 people handle the unit during assembly.

1. Remove two screws at rear side of top cover.

2. Remove top cover and thermostat knob, then place it aside.

3. Unscrew top hinge and then remove door and place it on a soft pad to

4. Unscrew bottom hinge. Then remove the adjustable feet from both

Reverse Door Tool required: Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner. Ensure the unit is unplugged and empty. To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid so that it will not slip during the door reversing process. All parts removed must be saved to do the reinstallation of the door. Do not lay the unit flat as this may damage the coolant system. It' s better that 2 people handle the unit during assembly.

1. Remove two screws at rear side of top cover.

2. Remove top cover and thermostat knob, then place it aside.

3. Unscrew top hinge and then remove door and place it on a soft pad to

4. Unscrew bottom hinge. Then remove the adjustable feet from both

tak aby se nepoškrábaly. Reverse Door Tool required: Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner. Ensure the unit is unplugged and empty. To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid so that it will not slip during the door reversing process. All parts removed must be saved to do the reinstallation of the door. Do not lay the unit flat as this may damage the coolant system. It' s better that 2 people handle the unit during assembly.

1. Remove two screws at rear side of top cover.

2. Remove top cover and thermostat knob, then place it aside.

3. Unscrew top hinge and then remove door and place it on a soft pad to

4. Unscrew bottom hinge. Then remove the adjustable feet from both

Reverse Door Tool required: Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner. Ensure the unit is unplugged and empty. To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid so that it will not slip during the door reversing process. All parts removed must be saved to do the reinstallation of the door. Do not lay the unit flat as this may damage the coolant system. It' s better that 2 people handle the unit during assembly.

1. Remove two screws at rear side of top cover.

2. Remove top cover and thermostat knob, then place it aside.

3. Unscrew top hinge and then remove door and place it on a soft pad to

4. Unscrew bottom hinge. Then remove the adjustable feet from both

5. Unscrew and remove the bottom hinge pin, turn the bracket over and replace it.

6. Refit the bracket fitting the bottom hinge pin. Replace both adjustable

7. Place the door back on. Ensure the door is aligned horizontally and

vertically, so that the seals are closed on all sides before finally tightening the top hinge.

8. Put the top cover and fix it with 2 screws on the back.

5. Unscrew and remove the bottom hinge pin, turn the bracket over and replace it.

6. Refit the bracket fitting the bottom hinge pin. Replace both adjustable

7. Place the door back on. Ensure the door is aligned horizontally and

vertically, so that the seals are closed on all sides before finally tightening the top hinge.

8. Put the top cover and fix it with 2 screws on the back.

5. Unscrew and remove the bottom hinge pin, turn the bracket over and replace it.

6. Refit the bracket fitting the bottom hinge pin. Replace both adjustable

7. Place the door back on. Ensure the door is aligned horizontally and

vertically, so that the seals are closed on all sides before finally tightening the top hinge.

8. Put the top cover and fix it with 2 screws on the back.

5. Unscrew and remove the bottom hinge pin, turn the bracket over and replace it.

6. Refit the bracket fitting the bottom hinge pin. Replace both adjustable

7. Place the door back on. Ensure the door is aligned horizontally and

vertically, so that the seals are closed on all sides before finally tightening the top hinge.

8. Put the top cover and fix it with 2 screws on the back.

MANIPULSCE S PŘÍSTROJEM

Temperature setting recommendation: 4°C is recommended. Under recommended setting, the best storage time of freezer is no more than 3 days. The best storage time may reduce under other settings.

Temperature setting recommendation: 4°C is recommended. Under recommended setting, the best storage time of freezer is no more than 3 days. The best storage time may reduce under other settings.

Reverse Door Tool required: Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner. Ensure the unit is unplugged and empty. To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid so that it will not slip during the door reversing process. All parts removed must be saved to do the reinstallation of the door. Do not lay the unit flat as this may damage the coolant system. It' s better that 2 people handle the unit during assembly.

1. Remove two screws at rear side of top cover.

2. Remove top cover and thermostat knob, then place it aside.

3. Unscrew top hinge and then remove door and place it on a soft pad to

4. Unscrew bottom hinge. Then remove the adjustable feet from both

2. Odstráňte horný kryt.

Reverse Door Tool required: Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner. Ensure the unit is unplugged and empty. To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid so that it will not slip during the door reversing process. All parts removed must be saved to do the reinstallation of the door. Do not lay the unit flat as this may damage the coolant system. It' s better that 2 people handle the unit during assembly.

1. Remove two screws at rear side of top cover.

2. Remove top cover and thermostat knob, then place it aside.

3. Unscrew top hinge and then remove door and place it on a soft pad to

4. Unscrew bottom hinge. Then remove the adjustable feet from both

tak aby sa predišlo poškriabaniu. Reverse Door Tool required: Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner. Ensure the unit is unplugged and empty. To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid so that it will not slip during the door reversing process. All parts removed must be saved to do the reinstallation of the door. Do not lay the unit flat as this may damage the coolant system. It' s better that 2 people handle the unit during assembly.

1. Remove two screws at rear side of top cover.

2. Remove top cover and thermostat knob, then place it aside.

3. Unscrew top hinge and then remove door and place it on a soft pad to

4. Unscrew bottom hinge. Then remove the adjustable feet from both

spotrebiča. Reverse Door Tool required: Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner. Ensure the unit is unplugged and empty. To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid so that it will not slip during the door reversing process. All parts removed must be saved to do the reinstallation of the door. Do not lay the unit flat as this may damage the coolant system. It' s better that 2 people handle the unit during assembly.

1. Remove two screws at rear side of top cover.

2. Remove top cover and thermostat knob, then place it aside.

3. Unscrew top hinge and then remove door and place it on a soft pad to

4. Unscrew bottom hinge. Then remove the adjustable feet from both

5. Unscrew and remove the bottom hinge pin, turn the bracket over and replace it.

6. Refit the bracket fitting the bottom hinge pin. Replace both adjustable

7. Place the door back on. Ensure the door is aligned horizontally and

vertically, so that the seals are closed on all sides before finally tightening the top hinge.

8. Put the top cover and fix it with 2 screws on the back.

5. Unscrew and remove the bottom hinge pin, turn the bracket over and replace it.

6. Refit the bracket fitting the bottom hinge pin. Replace both adjustable

7. Place the door back on. Ensure the door is aligned horizontally and

vertically, so that the seals are closed on all sides before finally tightening the top hinge.

8. Put the top cover and fix it with 2 screws on the back.

5. Unscrew and remove the bottom hinge pin, turn the bracket over and replace it.

6. Refit the bracket fitting the bottom hinge pin. Replace both adjustable

7. Place the door back on. Ensure the door is aligned horizontally and

vertically, so that the seals are closed on all sides before finally tightening the top hinge.

8. Put the top cover and fix it with 2 screws on the back.

5. Unscrew and remove the bottom hinge pin, turn the bracket over and replace it.

6. Refit the bracket fitting the bottom hinge pin. Replace both adjustable

7. Place the door back on. Ensure the door is aligned horizontally and

vertically, so that the seals are closed on all sides before finally tightening the top hinge.

8. Put the top cover and fix it with 2 screws on the back.

Temperature setting recommendation: 4°C is recommended. Under recommended setting, the best storage time of freezer is no more than 3 days. The best storage time may reduce under other settings.

Temperature setting recommendation: 4°C is recommended. Under recommended setting, the best storage time of freezer is no more than 3 days. The best storage time may reduce under other settings.

OHĽAD NA ŽIVOTNÉ PROSTREDIE