NuBlend BB180S - Blender Waring Commercial - Free user manual and instructions

Product type	Professional blender
Brand	Waring Commercial
Model	NuBlend BB180S
Voltage	120 V AC, 50/60 Hz, single-phase
Motor type	Universal, lifetime lubrication
Jar material	Polycarbonate (1.3 L) or stainless steel (1 L)
Jar capacity	1.3 L (polycarbonate) / 1 L (stainless steel)
Cord length	1.85 m
Plug type	3-prong with grounding
Speeds	Slow (LO), Fast (HI), Pulse
Pulse function	Yes, press the switch down
Thermal protection	Automatic shut-off in case of overheating
Blade safety	Very sharp blades, handle with care
Use of hot liquids	Maximum 250 ml, remove the cover cap
Maintenance	Unplug before cleaning, jar and blade assembly are removable
Sealing gasket	Between the jar and the blade assembly
Warranty	2-year limited (parts and labor)
Certification	cETLus (120 V models)
Intended use	Food, non-abrasive liquids, semi-liquids
After-sales service	Waring Factory Service Center, Torrington, CT

Frequently Asked Questions - NuBlend BB180S Waring Commercial

How to start the NuBlend BB180S blender?

Place ingredients in the jar, close the lid, plug in the appliance, then place the jar on the base ensuring the switch is OFF. Then, move the switch to the desired speed (LO or HI) or press down for the Pulse function.

What to do if the blender stops suddenly?

This may be due to thermal protection. Stop and unplug the appliance, empty the jar, let it cool for about 5 minutes, then plug back in and continue. If the problem persists, contact an authorized service center.

Can I blend hot liquids?

Yes, but do not exceed 250 ml and remove the cover cap before starting. Start at low speed and do not lean over the appliance.

How to clean the blender?

Always unplug the appliance before cleaning. The jar and blade assembly are removable. Wash them in warm soapy water. Blades are very sharp, handle with care. Never immerse the motor base.

Are the blades removable?

Yes, the blade assembly unscrews from the jar. To reassemble, place the sealing gasket between the jar and the blades, then screw the base clockwise.

What is the warranty on this blender?

Waring offers a two-year limited warranty against defects in material and workmanship. The motor is warranted for two years. For any claims, contact the authorized service center.

Can I use a plug adapter?

The appliance has a three-prong grounded plug. A temporary adapter may be used in the USA if the metal tab is attached to the housing, but it is prohibited in Canada. Consult an electrician if in doubt.

What types of ingredients can I blend?

The appliance is designed for food products, non-abrasive liquids, and semi-liquids. Avoid biologically active materials without prior sterilization.

How to use the Pulse function?

Press the switch down to the PULSE position. The appliance runs at high speed as long as you hold the switch. Release to stop.

Where can I get spare parts?

Spare parts are available from the Waring Factory Service Center in Torrington, CT (tel. [phone]) or through an authorized repair center.

USER MANUAL NuBlend BB180S Waring Commercial

Two NuBlend-branded blender models shown side by side, one black and one silver, with control buttons visible (no text or symbols on the devices themselves)

BB180/BB190 BB180S/BB190S (not shown)

For your safety and continued enjoyment of this product, always read the instruction book carefully before using.

When using electrical appliances, basic safety precautions should always be followed including the following:

1. READ ALL INSTRUCTIONS

1. Always unplug from outlet prior to handling or cleaning.

2. To protect against electrical hazards, do not immerse the blender base in water or other liquid.

3. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
4. Children should be supervised to ensure that they do not play with the appliance.
5. Unplug from outlet when not in use, before putting on or taking off parts, and before cleaning.
6. Avoid contacting moving parts.
7. Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or is dropped or damaged in any manner. Return appliance to the nearest authorized service facility for examination, repair or electrical or mechanical adjustment.
8. The use of attachments including canning jars not recommended by the appliance manufacturer may cause hazards.
9. Do not use outdoors.
10. Do not let cord hang over edge of table or counter, or touch hot surfaces.
11. Keep hands and utensils out of container while blending, to prevent the possibility of severe personal injury and/or damage to the blender. A rubber scraper may be used, but must be used only when the blender is not running.
12. Blades are sharp. Handle carefully.
13. Your blender utilizes a removable jar base and blade assembly; to avoid injury, never place cutting assembly or cutting blades on base without container properly attached.

14. Always operate blender with cover in place.

15. When blending hot liquids, remove centerpiece of two-piece cover. See Hot Blending Instructions.

SAVE THESE INSTRUCTIONS

RESETTING THERMAL PROTECTION

• The Blender you have purchased is equipped with an Automatic Reset Switch to protect the motor from overheating.
• If your blender stops running under heavy use, turn the Power Switch "Off" and Unplug the Power Cord. Empty the blender container of all its contents and allow approximately 5 minutes for the motor to cool down.
• Plug the power Cord back into the outlet and continue blending.
• If your blender does not function properly following this procedure, discontinue use and contact a Certified Waring Customer Service Center.

BIENDER

One Quart Capacity Specifications

• Ratings 120 VAC-50/60 Hz-single phase
- Motors Permanently lubricated series-wound universal type
- Container 44 oz. Polycarbonate or 32 oz. Stainless Steel
- Cord 6 foot 18 gauge three conductor grounding cord with strain relief
• cETLus 120 Volt models

gROUNDING INSTRUCTIONS

• For your protection, Waring® Commercial Blenders are equipped with a 3-conductor cord set.
• 120 volt units are supplied with a molded 3-prong grounding type plug and should be used in combination with a properly connected grounding-type outlet, as show in Figure A.

If a grounding type outlet is not available, an adapter, shown in Figure B, may be obtained to enable a 2-slot wall outlet to be used with a 3-prong plug.

Referring to Figure C, the adapter must be grounded by attaching its grounding lug under the screw of the outlet cover plate.

CAUTION: Before using an adapter, it must be determined that the outlet cover plate screw is properly grounded. If in doubt, consult a licensed electrician.

Never use an adapter unless you are sure it is properly grounded.

NOTE: Use of an adapter is not permitted in Canada.

A.

Circuit Grounding Conductor Connected Properly Grounding Prong

B.

C.

OPERATION

1. Put ingredients into container and cover it. Always add liquid ingredients first, unless otherwise specified in recipe. Do not fill above MAX line. Plug the blender cord into outlet.
2. With the toggle switch in OFF position, place container on blender. Be sure container is fully seated and that drive coupling is properly engaged.
3. This blender has 2 speed settings: HI and LO. Switch toggle to desired position. To crush ice, use HI speed setting.
4. This blender is equipped with a PULSE option. Hold toggle in down position to engage PULSE function. Unit will run on HI speed until the toggle switch is released.

Rubber Seal

1. When finished processing, set toggle switch to OFF position.

2. Allow motor to come to a complete stop before removing container from blender.

3. Note: Containers with removable bottoms have right-handed threads. When reassembling, be sure rubber seal is positioned between the container and the flange on the blade assembly.

IMPORTANT HOT BIENDING INSTRUCTIONS

To minimize the possibility of being scalded when blending hot materials, the following precautions and procedures must be observed.

1. Limit the amount of materials processed to 1/2 pint.
2. Completely remove the center portion of the two-piece container lid before starting motor. (This will allow venting of the

rapidly heated and expanding air present inside the container when blender is running.)

1. Always start blending at lowest speed setting, and then progress to desired speed.
2. Never stand directly over blender when it is being started or while it is running.

SERVICE

Refer to the list of Authorized Service Centers enclosed with your Waring® Commercial Blender for the name of the nearest Service Center, or write to:

Waring Factory Service Center P.O Box 3201

314 Ella T. Grasso Avenue

Torrington, CT 06790

[phone]

Ship blenders for repair to the above address or to an Authorized Service Center. Do not ship to a Waring Sales Office.

Note: If your application involves the processing of biologically active material, we request that any items returned for service be sterilized before being shipped. Such items must be clearly identified as having been sterilized, both by a tag on the item itself and by a statement in the accompanying correspondence. Waring will not accept delivery of any return unless it is so identified.

Replacement parts for your "Out of Warranty" repairs are obtainable at the above address.

llmITED Two YEAR wARRANTY

Waring warrants every new Waring Commercial Blender to be free from defects in material and workmanship for a period of two years from the date of purchase when used with foodstuffs, nonabrasive liquids (other than detergents) and nonabrasive semi-liquids, provided it has not been subject to loads in excess of the indicated rating. In addition, the motor in this appliance has a full two year warranty.

Under this warranty, the Waring Commercial Division will repair or replace any part which, upon our examination, is defective in materials or workmanship, provided the product is delivered prepaid to the Waring Service Center at: 314 Ella T. Grasso Ave. Torrington, CT 06790, or any Factory Approved Service Center.

This warranty does not: a) apply to any product which has become worn, defective, damaged or broken due to use or due to repairs or servicing by other than the Waring Service Center or a Factory Approved Service Center, or due to abuse, misuse, overloading or tampering; or b) cover incidental or consequential damages of any kind.

The two year warranty is applicable only to appliances used in the United States or Canada; this supersedes all other express product warranty or warranty statements. For Waring products sold outside of the U.S. and Canada, the warranty is the responsibility of the local importer or distributor. This warranty may vary according to local regulations.

warning: This warranty is void if appliance is used on Direct Current (D.C.)

VARING COMMERCIAL

14 Ella T. Grasso Ave.

Torrington, CT 06790

Any trademarks or service marks of third parties herein are the trademarks or service marks of their respective owners.

©2011 Waring Products

©2011 Waring Products

©2011 Waring Products

BB180/BB190 Series IB

11WC123322