VZ45CT - Sink SMEG - Free user manual and instructions

Find the device manual for free VZ45CT SMEG in PDF.

SMEG VZ45CT - Sink
📄 42 pages English EN Download 💬 AI Question 10 questions ⚙️ Specs
Notice SMEG VZ45CT - page 6
Pick your language and provide your email: we'll send you a specifically translated version.
BrandSmeg
ModelVZ45CT
Product typeKitchen sink
MaterialComposite (granite)
Dimensions (L x D x H)45 x 45 x 20 cm (estimate)
WeightApproximately 10 kg (estimate)
Available colorsLight and dark
Installation typeDrop-in or undermount
Number of bowls1
Integrated drainboardNot specified
Faucet holeYes (standard)
Stain resistanceYes, with anticalc treatment
Impact resistanceHandle with care
Heat resistanceAvoid hot pans
Daily cleaningClean with soft sponge and mild detergent
Stubborn stains (light color)Diluted bleach solution
Stubborn stains (dark color)Circular movements with sponge
DescalingSuitable descaling product
PrecautionsDo not cut directly, avoid impacts, do not pour boiling liquids without cold water
InstallationBy a professional, silicone not provided
Manual42 pages, available in multiple languages
WarrantyStandard warranty provided cleaning instructions are followed

Frequently Asked Questions - VZ45CT SMEG

How to install my Smeg VZ45CT sink?
Installation must be carried out by qualified personnel according to current standards. Silicone is not provided. Before assembly, clean the sink with ordinary detergent and a soft sponge.
What cleaning product to use for the sink?
Use an ordinary dishwashing detergent and a soft non-abrasive sponge. Rinse and dry with a microfiber cloth. Avoid alkaline detergents, ammonia, caustic soda or harsh liquids.
How to remove stubborn stains on a light-colored sink?
Prepare a solution of bleach and warm water (3/4 and 1/4). Leave to act for approximately 8 hours (preferably overnight), then rinse thoroughly and dry. Repeat 1 to 2 times if necessary.
How to remove stubborn stains on a dark-colored sink?
Use a soft non-abrasive sponge and ordinary dishwashing detergent, making small circular motions. Rinse with warm water and dry carefully. Repeat if necessary.
How to remove limescale stains?
Use a descaling and anti-corrosion product diluted in warm water. Apply evenly, leave for a few minutes, gently rub with a soft sponge, then rinse and dry.
What usage precautions to avoid damaging the sink?
Avoid cutting or chopping directly on the surface (use a cutting board). Do not place hot pans directly. Do not pour boiling liquids without running cold water and without at least 1 cm of water at the bottom. Avoid impacts that could cause micro-damage.
How to prevent limescale stains?
Carry out a descaling treatment at least once a week. Fill the bowl with warm water, add two tablespoons of liquid or powder laundry detergent or a tablet. Leave for 5 to 6 hours, rinse and dry thoroughly.
Can I use abrasive sponges or steel wool?
No, never use steel wool or abrasive sponges as they can scratch the surface and irreparably damage the sink.
What to do if water stays on the surface for a long time?
Dry every day the surface of the sink with a microfiber cloth to avoid prolonged water deposits that promote limescale formation.
Where to find the complete user manual?
The 42-page manual is available for free download in PDF format on our website. You can also request a translation into your language by providing your email.

User questions about VZ45CT SMEG

0 question about this device. Answer the ones you know or ask your own.

Ask a new question about this device

Your email remains private: it is only used to notify you if someone answers your question.

No questions yet. Be the first to ask one.

Download the instructions for your Sink in PDF format for free! Find your manual VZ45CT - SMEG and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. VZ45CT by SMEG.

USER MANUAL VZ45CT SMEG

SILICONE

Isometric diagram of a device with two stacked plates and directional arrows indicating movement or force (no text or symbols).

LAVELLO TOP

graph TD A["Step 1"] --> B["Central Structure"] C["Step 2"] --> B D["Step 3"] --> B E["Step 4"] --> B F["Step 5"] --> B G["Step 6"] --> B

TOP SILICONE LAVELLO

graph TD A["1"] --> B["2"] C["3"] --> D["4"] E["5"] --> F["6"] G["Bottom Left"] --> H["Bottom Right"] I["Bottom Right"] --> J["Bottom Left"]

Simple line drawing of a hand covering a cloth with motion lines (no text or symbols).

2. NON-ROUTINE MAINTENANCE

Simple line drawing of a cooking pot with steam rising, crossed by a black X (no text or symbols).

SMEG VZ45CT - NON-ROUTINE MAINTENANCE - 2

Before fitting the sink, it is advisable to wash it using standard dish detergent and a soft sponge to remove any manufacturing residues.

Rinse the sink thoroughly and dry it using a microfibre cloth.

SMEG VZ45CT - NON-ROUTINE MAINTENANCE - 3

STANDARD INSTALLATION

Diagram illustrating a drill bit and screwdriver tool application, with a magnified view showing the process.

SILICONE

Isometric diagram of a device with two stacked plates and directional arrows indicating movement or force (no text or symbols).

SINK TOP

graph TD A["①"] --> B["Central Structure"] C["⑤"] --> B D["③"] --> B E["④"] --> B F["⑥"] --> B G["②"] --> B

SMEG VZ45CT - STANDARD INSTALLATION - 6

UNDERMOUNT INSTALLATION

TEMPLATE ① ②

15 mm Ø 11.5 mm

SILICONE

Diagram of a mechanical assembly with two stacked components and upward arrows indicating motion (no text or symbols)

TOP SILICONE SINK

graph TD A["1"] --> B["2"] C["3"] --> D["4"] E["5"] --> F["6"] G["Bottom Left"] --> H["Bottom Right"] I["Bottom Right"] --> J["Bottom Left"]

SMEG VZ45CT - UNDERMOUNT INSTALLATION - 7

The packaging materials (plastic bags, expanded polystyrene, etc.) must not be left within reach of children as they are a potential hazard.

SMEG VZ45CT - UNDERMOUNT INSTALLATION - 8

Installation and support should be undertaken by qualified individuals, in accordance with the applicable legal requirements.

The silicone is not included with the product. The sink shown in this guide is for illustrative purposes only.

SMEG VZ45CT - UNDERMOUNT INSTALLATION - 9

1. ROUTINE MAINTENANCE

Cleaning your Smeg product is quick and simple. Even though the non-porous surface prevents liquids penetrating into the material, it is preferable to remove them immediately using a soft, non-abrasive sponge and standard dish detergent. You should then rinse the surface and dry it carefully using a microfibre cloth.

Simple line drawing of a hand cleaning a surface with a cloth (no text or symbols)

2. NON-ROUTINE MAINTENANCE

Cleaning stubborn stains is not difficult: all you need to do is choose the right product and use it correctly.

SMEG VZ45CT - NON-ROUTINE MAINTENANCE - 1

For stubborn stains on LIGHT-COLOURED products, you can use a solution of bleach and warm water (3/4 to 1/4), leaving it to act for eight hours (we recommend that this cleaning be performed during the night). Afterwards, rinse thoroughly and dry the entire surface carefully using a microfibre cloth. If the stains remain, the operation can be repeated one or two more times.

SMEG VZ45CT - NON-ROUTINE MAINTENANCE - 2

For stubborn stains on DARK-COLOURED products, you can remove them directly with a soft, non-abrasive sponge and standard dish detergent, using small circular movements. When finished, rinse using warm water and carefully dry the entire surface using a microfibre cloth. If the stains remain, the operation can be repeated one or two more times.

SMEG VZ45CT - NON-ROUTINE MAINTENANCE - 3

To remove limescale stains, we recommend the use of a non-corrosive descaling product diluted with warm water. Distribute the solution uniformly over the entire surface of the product. Clean with a soft, non-abrasive sponge using small circular movements and leave the product to act for several minutes (follow the instructions and conditions for use on the product label). When finished, rinse using warm water and dry carefully using a microfibre cloth.

Failure to follow the cleaning and maintenance instructions stated in this manual may invalidate the standard warranty provided by the manufacturer.

SMEG VZ45CT - NON-ROUTINE MAINTENANCE - 4

To ensure that there is no change to the characteristics of the product, we recommend that users observe the following precautions:

- dry the surface of the product every day to avoid prolonged exposure to water that could lead to the build-up of limescale or stubborn stains

- do not use detergents that contain alkaline substances and aggressive liquids (such as ammonia, caustic soda or drain cleaners)

- do not remove traces of dirt using steel scourers or abrasive sponges that could damage the surface

- do not cut or chop directly on the surface of the product because this could cause irreparable scratches (always use chopping boards)

- avoid accidental knocks that could cause irreparable micro-damage

- do not place hot cookware, pans or coffee makers directly on the sink surface: stains from discolouration and/or damage could form in areas where hot items are placed

- avoid pouring boiling liquids directly into the sink without first turning on the cold tap and filling the sink with at least 1 cm of water, as this could damage the product

• to prevent the build-up of limescale, it is recommended that a descaling treatment be completed at least once a week. This is recommended in particular for dark-coloured sinks. Fill the tub with warm water and add two spoonfuls of liquid or powder dishwasher detergent or a dishwasher tab. Leave the solution for 5/6 hours. Rinse thoroughly and dry carefully.

Simple line drawing of a crossed-out kitchen counter with no text or symbols

Simple line drawing of a cooking pot with steam rising, crossed by a black X (no text or symbols)

SMEG VZ45CT - NON-ROUTINE MAINTENANCE - 7

Do not put pans or coffee makers that have just been taken off the heat (which sometimes reach 500°C) directly into sink.

Diagram illustrating a drill bit and screwdriver tool application, with Chinese labels for each step.

SILICONE

Isometric diagram of a device with two stacked plates and directional arrows indicating movement or force (no text or symbols)

SINK TOP

graph TD A["1"] --> B["Central Structure"] C["2"] --> B D["3"] --> B E["4"] --> B F["5"] --> B G["6"] --> B

SMEG VZ45CT - NON-ROUTINE MAINTENANCE - 13

Installation under the countertop

1 2 PATTERN

15 mm Ø 11.5 mm

SILICONE

Diagram of a layered mechanical or electronic component with upward arrows indicating motion or force, no text or symbols present.

TOP SILICONE SINK

graph TD A["1"] --> B["2"] C["3"] --> D["4"] E["5"] --> F["6"] G["Bottom Left"] --> H["Bottom Right"] I["Bottom Right"] --> J["Bottom Left"]

Simple line drawing of a hand cleaning a surface with a cloth (no text or symbols)

Simple line drawing of a cooking pot with steam rising, crossed by a diagonal line (no text or symbols)

Diagram illustrating a drill bit and screwdriver tool application, with a magnified view showing the process.

SILICONE

Isometric diagram of a device with two stacked plates and directional arrows indicating movement or force (no text or symbols)

SINK WORKTOP

graph TD A["1"] --> B["Object"] C["2"] --> B D["3"] --> B E["4"] --> B F["5"] --> B G["6"] --> B

Under-counter installationSMEG VZ45CT - Installation under the countertop - 14

TEMPLATE ① ②

15 mm Ø 11.5 mm

SILICONE

Diagram of a mechanical assembly with two stacked components and upward arrows indicating motion (no text or symbols)

WORKTOP SILICONE SINK

graph TD A["①"] --> B["②"] C["③"] --> D["④"] E["⑤"] --> F["⑥"] G["⑦"] --> H["⑧"]

Simple line drawing of a hand cleaning a surface with a cloth (no text or symbols)

Simple line drawing of a cooking pot with steam rising, crossed by a black X (no text or symbols)

Diagram illustrating a drill bit and screwdriver tool application, with Chinese labels for each step.

SILICONE

Isometric diagram of a device with two stacked plates and directional arrows indicating movement or force (no text or symbols)

SINK COUNTERTOP

graph TD A["①"] --> B["⑤"] B --> C["③"] C --> D["④"] D --> E["⑥"] E --> F["②"] F --> G["⑤"]

Diagram of a mechanical assembly with two stacked components and upward arrows indicating motion (no text or symbols)

COUNTERTOP SILICONE SINK

graph TD A["1"] --> B["2"] C["3"] --> D["4"] E["5"] --> F["6"] G["Bottom Left"] --> H["Bottom Right"] I["Bottom Right"] --> J["Bottom Left"]

Simple line drawing of a hand cleaning a surface with a cloth (no text or symbols)

Simple line drawing of a cooking pot with a crossed-out X symbol (no text or labels)

Diagram illustrating a drill bit and screwdriver tool application, with a magnified view showing the process.

SILICONE

Isometric diagram of a device with two stacked plates and directional arrows indicating movement or force (no text or symbols)

DISHWASHER COUNTERTOP

graph TD A["1"] --> B["Object"] C["5"] --> B D["3"] --> B E["4"] --> B F["6"] --> B G["2"] --> B

Diagram of a mechanical assembly with two stacked components and upward arrows indicating motion (no text or symbols)

COUNTERTOP SILICONE DISHWASHER

graph TD A["1"] --> B["2"] C["3"] --> D["4"] E["5"] --> F["6"] G["Bottom Left"] --> H["Top Right"] I["Bottom Right"] --> J["Bottom Left"]

Simple line drawing of a hand cleaning a surface with a cloth (no text or symbols)

Simple line drawing of a crossed-out kitchen counter with steam rising (no text or symbols)

Diagram illustrating a drill bit and screwdriver tool application, showing correct and incorrect states of the process.

SILICONE

Isometric diagram of a device with two stacked plates and directional arrows indicating movement or force (no text or symbols)

Diagram of a mechanical assembly with two stacked components and upward arrows indicating motion (no text or symbols)

Hand wiping a surface with a cloth (no text or symbols)

2. Non-scheduled maintenance

Simple line drawing of a kitchen with a crossed-out black X symbol (no text or labels)

Diagram illustrating a drill bit and screwdriver tool, showing correct and incorrect states of the process.

SILICONE

Isometric diagram of a device with two stacked plates and directional arrows indicating movement or force (no text or symbols)

SINK COUNTERTOP

graph TD A["1"] --> B["Central Object"] C["5"] --> B D["3"] --> B E["4"] --> B F["6"] --> B G["2"] --> B

Installation under the countertopSMEG VZ45CT - Non-scheduled maintenance - 7

TEMPLATE ① ②

15 mm Ø 11.5 mm

SILICONE

Diagram of a mechanical assembly with two stacked components and upward arrows indicating motion (no text or symbols)

BLAT SILICONE SINK

graph TD A["1"] --> B["2"] C["3"] --> D["4"] E["5"] --> F["6"] G["Bottom Left"] --> H["Bottom Right"] I["Bottom Right"] --> J["Bottom Left"]

Simple line drawing of a hand cleaning a surface with a cloth (no text or symbols)

2. ROUTINE MAINTENANCE

Simple line drawing of a cooking pot with steam rising, crossed by a black X (no text or symbols)

Diagram illustrating a drill bit and screwdriver tool application, showing correct/incorrect states of the process.

SILICONE

Isometric diagram of a device with two stacked plates and directional arrows indicating movement or force (no text or symbols)

Diagram of a mechanical assembly with two stacked components and upward arrows indicating motion (no text or symbols)

SALT SHAKER SILICONE KITCHEN SINK

graph TD A["1"] --> B["2"] C["3"] --> D["4"] E["5"] --> F["6"] G["Bottom Left"] --> H["Bottom Right"] I["Bottom Right"] --> J["Bottom Left"]

Simple line drawing of a hand cleaning a surface with a cloth (no text or symbols)

Simple line drawing of a kitchen with a crossed-out black X symbol (no text or labels)

Diagram illustrating a drill bit and screwdriver tool application process with labeled components.

Silicone

Isometric diagram of a device with two stacked plates and directional arrows indicating movement or force (no text or symbols).

Diagram of a layered mechanical or electronic component with upward arrows indicating motion or force, no text or symbols present.

Two hand icons with different textures, one covering a cloth and the other covering a surface (no text or symbols).

Simple line drawing of a crossed-out kitchen counter with no text or symbols.

Simple line drawing of a cooking pot with crossed-out black lines (no text or symbols).

SMEG VZ45CT - ROUTINE MAINTENANCE - 17

Manual assistant
Powered by Anthropic
Waiting for your message
Product information

Brand : SMEG

Model : VZ45CT

Category : Sink