MS-125 - Vacuum Cleaner Mestic - Free user manual and instructions

USER MANUAL MS-125 Mestic

1. Do not vacuum water, liquids, ash, hot objects, cigarettes, coal, or other objects not intended.

2. Do not vacuum highly ammable substances, or use the product near highly ammable substances (liquids or vapours).

3. Do not vacuum toxic material (such as bleach, ammonia, drain cleaner, ect.).

4. Do not vacuum toners (from printers or copiers), there is a risk of re and explosion.

5. Do not vacuum cement, plaster or other nely dusty materials. This can clog the lter.

6. Do not use if any of the lters are missing from the unit.

7. Do not use or store near appliances that generate a lot of heat or in places with high temperatures.

8. When vacuuming, do not run the vacuum cleaner mouth over the power cord.

9. Do not use if the device is blocked anywhere. First switch off the device and remove the blockage before resuming work.

10. Do not use if lters are clogged. In this case, the lters must be cleaned before continuing.

11. Do not use when the device makes strange noises, is broken, smells strange, smoke comes out, shows other damage and does not work properly. In this case, consult the nearest authorized service point in your area and have the product checked there. 12. Do not misuse the power cord, which means that it should not be used to pull the device towards you. When pulling out the plug, it is also important to do this as close to the socket as possible and not to pull on the cord.

13. Do not use to pick up large or sharp objects such as, glass, screws, shards ect.

14. Do not leave the appliance unattended when it is connected to the mains socket.

15. Do not use if the device has been damaged, has been left outdoors, or has been exposed to water or other humid conditions. 16. Be careful with the power cord. Do not pull too hard or let sharp objects pass over it. Be careful with sharp corners.

17. Do not use if you have wet or dirty hands, it may affect the operation in a dangerous way.

18. Do not put objects other than absorbable dirt into the openings of the vacuum cleaner as this can cause irreparable damage.

19. Do not use if an opening is clogged.

20. Do not use if the appliance power cord has visible damage. In this case, have the device checked by an authorized dealer or contact the importer.

21. Do not attempt to make any adjustments to the device.

22. Important: empty the dust container in time to prevent blockage.

23. Important: keep hair, clothes, body parts away from the openings of the vacuum cleaner. This can lead to dangerous situations.

24. Important: always switch off the device with the on/off switch before plugging in or out of the socket.

25. Important: always remove the plug from the socket when the appliance is not in use, the lters must be cleaned or other maintenance is necessary.

26. Important: use indoors only.

27. Important: use the device only as described in the manual.

28. Important: keep the power cord away from hot surfaces, such as radiators, etc.

29. Important: keep all suction openings free of blockage.

30. Important: pay extra attention when using the vacuum cleaner on stairs.

31. Important: make sure the work area is well lit.

32. Important: store the device in a cool, dry place after use.

33. Important: make sure that packaging materials, accessories and other loose parts are not in the vicinity of children or babies.

34. Important: use the appliance only on the mains voltage stated on the label on the appliance.

35. Important: if the device is used by third parties, please provide them with these instructions.

36. Important: this device is only suitable for the user’s purposes as described in this manual.

ENGLISHCharacteristics:

1. Button to release bin

4. Air intake opening

9. Telescopic vacuum cleaner tube

Important: The above specications and components are always subject to change. Usage: Read and keep these instructions carefully. To move the vacuum cleaner from one room to the next, carry it by the handle. Never carry the appliance by the connecting cable. Montage methode: Before you start installing the device, check that all necessary parts from the list above are present. Make sure that the connecting cable is not connected to the mains socket. Installing the vacuum cleaner tube

1. Mount the telescopic tube on the vacuum cleaner opening.

2. Now connect the oor brush to the other end of the telescopic tube.

Connecting the accessories

1. To t one of the attachments, it is necessary to remove the telescopic tube rst.

2. After this, the attachment can be mounted.

Usage The power cord

1. Unroll the cord and insert the plug into the socket.

2. Press the on/off switch to start the engine.

3. Remove the plug from the socket after use.

9Emptying the dust container Empty the hopper as often as possible. An overlled container can cause blockage.

WARNING: The plug must be disconnected from the mains before the container can be emptied.

Emptying the container - method 1 Stand with the vacuum cleaner over a waste bin and press the button to open the container. The cover at the bottom of the container will now open. Emptying the container - method 2 Remove the container completely from the vacuum cleaner by pressing the container release button. You can now remove the entire container from the device. Now empty the container by standing over a waste bin and open the ap at the bottom of the container by pressing the empty button. Cleaning the lters

WARNING: If the lters are clogged or the suction power is greatly reduced, clean the lters to prevent further damage.

Never use the device without lters, this will cause irreparable damage.

1. Remove the container from the device.

2. Rotate the top of the container counterclockwise to remove it.

3. The lter can now be removed.

ENGLISHTo safely clean the lters, the lter can be shaken above a waste bin. In case of stubborn dirt, the lter can be cleaned under the tap. Before replacing the lters, they must be completely dry. Do not under any circumstances use a hard brush, this can irreparably damage the lters. Replacing the lters 1. Place the lter housing back into the container by aligning the triangle mark (on the top) and the line marking on the side of the container. 2. Now put the lters back in place and close with the cover. Align it in the same way as the lter housing until it clicks into place.

3. Now reassemble the motor housing and the collector by clicking them together.

4. Now put the exhaust lter back in place and click the grill cover back on.

Important while cleaning

1. The lters should be cleaned regularly to ensure the best performance of the device and to avoid overheating.

2. Cleaning is best done after you have emptied the container.

3. Never operate the appliance when the lters are still wet or when no lters are installed.

4. Wash the lters in medium hot water with a mild, non-aggressive detergent. Then rinse them with cold water and let them dry completely.

5. Clean the lter housing with medium hot water and let it dry completely.

6. Using wet lters can create dangerous situations and cause irreparable damage to you and the device.

7. Do not dry the lters with a hair dryer.

8. Do not clean any parts of the vacuum cleaner or lters with fuel or other highly ammable products.

9. Only clean the vacuum cleaner itself on the outside, using only a damp cloth and a mild detergent.

10. After cleaning, dry off the moisture from the vacuum cleaner, parts and accessories with a dry cloth.

11. Do not put accessories or parts in a dishwasher.