GL347 - Boiler BUFFALO - Free user manual and instructions

USER MANUAL GL347 BUFFALO

• Position on a flat, stable surface.

• A service agent/qualified technician should carry out installation and any repairs if required. Do not remove any components on this product.

• Consult Local and National Standards to comply with the following:

• Health and Safety at Work Legislation

• IEE Wiring Regulations

• Building Regulations

• Ensure the location for the appliance can support its weight when full.

• DO NOT immerse the appliance in water.

• DO NOT leave the machine unattended during operation.

• DO NOT operate this appliance when less than one third full.

• DO NOT touch the outer surfaces of the appliance. They become hot during use.

• Suitable for indoor use only.

• Always switch off and disconnect the power supply to the appliance when not in use.

• Keep all packaging away from children. Dispose of the packaging in accordance to the regulations of local authorities.

• If the power cord is damaged, it must be replaced by an BUFFALO agent or a recommended qualified technician in order to avoid a hazard.

• Please ensure that the tap is screwed fully on before use. Product Description

• GL349 - 40 litre Stainless Steel Water Boiler Introduction Please take a few moments to carefully read through this manual. Correct maintenance and operation of this machine will provide the best possible performance from your BUFFALO product. Pack Contents The following is included:

• BUFFALO Water Boiler

• Instruction manual BUFFALO prides itself on quality and service, ensuring that at the time of packaging the contents are supplied fully functional and free of damage. Should you find any damage as a result of transit, please contact your BUFFALO dealer immediately.3

1. Remove the appliance from the

packaging. Make sure that all protective plastic film and plastic coatings are thoroughly removed from all surfaces.

2. Ensure the Temperature Control knob is

set to ‘0’ and tthe power switch is ‘Off’.

3. Remove the lid and fill the appliance to

at least half of its capacity.

5. Connect to the mains power supply and

the required temperature. The Heat Indicator illuminates and the appliance heats the water.

7. When the water has reached the set temperature the Heat Indicator light turns Off.

Note: Before using for the first time, clean the interior of the appliance and all parts in warm soapy water, then rinse thoroughly.

WARNING: Reduce the set temperature if the the water begins to boil. DO NOT allow

the water to boil constantly. Note: Once the water temperature drops 5-10ºC then the appliance will reheat the water.

WARNING: If the Temperature Control Knob is set to or close to ‘100’ then the appliance

will constantly heat the water until the power switch is turned Off or the temperature is reduced. Lid Handle Tap Temperature Control knobOn/Off switchPower Indicator light4

Approximate Temperature Guide: Thermal Cut-Out Reset This appliance is fitted with a Thermal Cut-Out safety feature. Should the temperature exceed safe levels the appliance will automatically cut power. The Safety Cut-out switch is located on the underside of the appliance. To reset the appliance:

1. Empty the appliance and allow to cool.

2. Press the reset button until it clicks.

3. The appliance is now reset and can be used as normal.

2. Pull the tap towards you to begin pouring.

3. Raise the tap handle to close the tap.

Emptying the Appliance Drain the appliance by using the tap to empty. Cleaning, Care & Maintenance

• Always turn off and disconnect the appliance from the power supply before cleaning.

• Use soapy water and a damp cloth to clean the exterior of the appliance.

• Dry thoroughly after cleaning. Thermostat Setting Approximate Temperature Off 1 39°C 2 50°C 3 62°C 4 76°C 5 90°C HIGH 100°C

WARNING: Ensure the appliance has cooled down and is empty before resetting the

switch, as it may need to be tipped slightly to gain access to the switch.5

Telephone Helpline: 0845 146 2887 (United Kingdom) Descaling In hard water areas lime scale can build up within the appliance after prolonged use. To descale the appliance:

1. Pour a solution of descaler and water into the appliance.

2. Brush the interior gently with a soft bristled brush.

3. Discard the solution collected in the jug.

4. Fill the appliance with clean water and turn back On to flush out the system.

Flush out the system thoroughly to remove any descaler residue.

5. The appliance is now ready for use.

Note: Use a suitable descaler and always follow the instructions on the container. BUFFALO recommend that this appliance is descaled every 3 months or more frequently in hard water areas. Fault Probable Cause Action The unit is not working The unit is not switched on Check the unit is plugged in correctly and switched on Plug and lead are damaged Call BUFFALO agent or qualified technician Fuse in the plug has blown Replace the plug fuse Power supply Check power supply Internal wiring fault Call BUFFALO agent or qualified technician Thermal fuse has activated Reset Thermal fuse (see page 3) Power light comes on but water does not reach temperature Thermostat fault Call BUFFALO agent or qualified technician The tap is leaking The tap has become loose Tighten the tap handle6

Technical Specifications Electrical Wiring This appliance is supplied with a 3 pin, moulded, BS1363 plug and lead, with a 13 amp fuse as standard. The plug is to be connected to a suitable mains socket. This appliance is wired as follows:

• Live wire (coloured brown) to terminal marked L

• Neutral wire (coloured blue) to terminal marked N

• Earth wire (coloured green/yellow) to terminal marked E This appliance must be earthed, using a dedicated earthing circuit. If in doubt consult a qualified electrician. Electrical isolation points must be kept clear of any obstructions. In the event of any emergency disconnection being required they must be readily accessible. Compliance The WEEE logo on this product or its documentation indicates that the product must not be disposed of as household waste. To help prevent possible harm to human health and/or the environment, the product must be disposed of in an approved and environmentally safe recycling process. For further information on how to dispose of this product correctly, contact the product supplier, or the local authority responsible for waste disposal in your area. BUFFALO parts have undergone strict product testing in order to comply with regulatory standards and specifications set by international, independent, and federal authorities. BUFFALO products have been approved to carry the following symbol: All rights reserved. No part of these instructions may be produced or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of BUFFALO. Every effort is made to ensure all details are correct at the time of going to press, however, BUFFALO reserve the right to change specifications without notice. Model Voltage Power Current Capacity Weight (full) Approx. Heating Time (Max. Temp. when full) Dimensions h x w d mm GL346 230V 50Hz 2600W 11.3A 10 litres 16.8kgs 22 minutes 470x313x326 GL347 230V 50Hz 2600W 11.3A 20 litres 29.2kgs 45 minutes 535x369x380 GL348 230V 50Hz 2600W 11.3A 30 litres 40.4kgs 60 minutes 519x433x440 GL349 230V 50Hz 2600W 11.3A 40 litres 48.2kgs 89 minutes 630x433x4407