TaskVac CH53010 - Vacuum Cleaner HOOVER - Free user manual and instructions

USER MANUAL TaskVac CH53010 HOOVER

Line drawing of a vacuum cleaner with handle and base (no text or symbols)

iMPoRtant: Read CaReFully BeFoRe asseMBIY and use.

Questions or concerns? For assistance, please call Customer Service at

1-800-321-1134 Mon-Fri 8am-7pm EST.

tHis ProduCt is intended FoR CoMMeRCial use only.

Please enter the complete model and Serial Number in the spaces provided.

MODEL

SERIAL NUMBER

Hint: Attach your sales receipt to this owner's manual. Verification of date of purchase may be required for warranty service of your HOOVER® product.

COMMERCIAL Technomic Floor Care Technology Limited 1-332-044-8200 (UK and Canada) boever.com VACUUM CLEANER/ ASPIRATEUR/ASPIRADORA MODEL/MODELE/MODELO XXXXXXXX 120 x. 60Hz. 12.9 A SERIES/SERIE/SERIE XX XX.X PLANT, JI MFG. CODE XXXX JI SERIAL NO./NUMERO DE SERIE/NUMERO SER. XXXXXXXXXXXXXX Distributed by HODDER, Inc. Glomwillow OH 44139 Made in Mexico/Fritiquet au Mesquen/Racho as México seRial nuMBeR (Label located on back of vacuum)

Contents

Important Safety Instructions....3

Vacuum Assembly 5

Carton Contents ....5

Attach Handle 5

Attach Dirt Cup ....5

Position Tools ....5

How To Use ....6

Vacuum Description ....6

On-Off Switch 6

Cord Storage 6

Carpet Height Adjustment ....6

Tools 7

Select Proper Tool 7

Removing Hose ....7

Attach Wand And Tools 7

Stair Cleaning ....7

How To Clean Tools ....7

Maintenance 8

Dirt Cup 8

Filters....9

Brushroll ....11

Hose....11

Belt....11

Troubleshooting ....13

Service....13

Warranty 14

If you need assistance:

Visit our website at hoover.com. Follow the authorized dealer locator link to find the Hoover® authorized dealer nearest you or call 1-800-944-9200 for an automated referral of Hoover® authorized dealer locations (U.S. only) or to speak with a customer service representative; Mon- Fri 8am- 7pm EST.

IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS

When using an electrical appliance, basic precautions should always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE.

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:

• Fully assemble before operating.
- Operate vacuum only at voltage specified on data label on back of cleaner.
- Do not leave appliance when plugged in. Unplug from outlet when not in use and before cleaning or servicing.
- Do not use outdoors or on wet surfaces.
- Do not allow to be used as a toy. Not intended for use by children age 12 and under. Close supervision is necessary when used near children. To avoid injury or damage, keep children away from product, and do not allow children to place fingers or other objects into any openings.
- Use only as described in this manual. Use only manufacturer's recommended attachments and products.
- Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, take it to a service center prior to continuing use.
- Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not place product on cord. Do not run appliance over cord. Keep cord away from heated surfaces.
- Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
- Do not handle plug or appliance with wet hands.
- Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air flow.
- Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts. Brushroll continues to rotate when in the upright position.
- Use extra care when cleaning on stairs. To avoid personal injury or damage, and to prevent the cleaner from falling, always place cleaner at bottom of stairs on floor. Do not place cleaner on stairs or furniture, as it may result in injury or damage.
- Do not use to pick up flammable or combustible liquids, such as gasoline, or fine wood sandings, or use in areas where they may be present.
- Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
- Do not use without Dirt Cup and/or Filters in place.
- WARNING: This product contains chemicals known to the State of California to cause cancer, birth defects or reproductive harm. WASH HANDS AFTER HANDLING.

CAUTION: TO REDUCE THE RISK OF DAMAGE:

• Avoid picking up hard, sharp objects with this product, as they may cause damage.
• Store appropriately indoors in a dry place. Do not expose machine to freezing temperatures.
• Brushroll continues to turn while product is turned on and handle is in upright position. To avoid damage to carpet, rugs, furniture and flooring, avoid tipping cleaner or setting it on furniture, fringed area rugs, or carpeted stairs during tool use. Always put the cleaner in “Suction Only Mode” (Available on select models only) during tool use.
• Do not use sharp objects to clean out hose as they can cause damage.

GROUNDING INSTRUCTIONS

This appliance must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor (C) and grounding plug (A). The plug must be inserted into an appropriate outlet (B) that is properly installed and grounded in accordance with all local codes and ordinances.

WARNING: Improper connection of the equipment-grounding conductor can result in the risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the appliance - if it will not fit the outlet, have a proper outlet installed by a qualified electrician. This appliance is for use on a nominal 120-volt circuit and has a grounding plug that looks like the plug (A) illustrated in Fig. 1. A temporary adapter (D) may be used to connect this plug to a 2-pole receptacle (E) if a properly grounded outlet is not available (Fig. 2). The temporary adapter should be used only until a properly grounded outlet (B) can be installed by a qualified electrician (Fig. 1). The green colored rigid ear, lug, or the like (F) extending from the adapter must be connected to a permanent ground (G) such as a properly grounded outlet box cover (Fig. 2). Whenever the adapter is used, it must be held in place by a metal screw. NOTE: In Canada, the use of a temporary adapter is not permitted by the Canadian Electrical Code.

1 A C B

2 D F D G E

1. VaCuuM asseMBIY

CaRton Contents

A. Handle*
B. Vacuum Base
C. Crevice Tool
D. Dusting/Upholstery Tool*
E. Wand
F. Screw (for assembly)
G. Dirt Cup

*Varies per model

Remove all parts from carton and identify each item shown.

Make sure all parts are located before disposing of packing materials.

1.1

B

Line drawing of a mechanical device with a cylindrical body and base (no text or symbols)

D

C

E

F

G

attaCH Handle

(varies per model)

Note: Remove the screw located in the vacuum base and set aside until instruction 1.3

1.2 Insert handle section into vacuum base. Push down firmly.
1.3 Using a Phillips screwdriver, fasten (1) screw behind handle into vacuum base.

1.2

Diagram showing a hand holding a tool with an arrow pointing to a mechanical component (no text or symbols present)

1.3

Line drawing of a hand holding a tool near a mechanical component (no text or symbols)

attaCH diRt CuP

1.4 Place bottom of dirt cup into vacuum body first. Pivot cup into vacuum. Dirt cup is secure when you hear a click.

1.4

Line drawing of a hand using a vacuum cleaner to handle the air (no text or symbols present)

Position tools

1.5 Place Crevice Tool into Wand and slide into tool storage area on left back side (B) of vacuum and place Upholstery Tool on right back side (C) of vacuum as shown.

1.5

B C

2. How to use

VaCuuM desCRiPtion

1. Handle*
2. ON/OFF Switch
3. Dirt Cup Release Button
4. Carry Handle
5. Dirt Cup
6. Stair Cleaning Handle
7. Furniture Guard

8. Filter made with HEPA media Access

9. Rinsable Filter Access

10. System Check Indicator

11. Crevice Tool

12. Wand

13. Hose

14. Handle Release Pedal

15. Hose Tube

16. Hose Release Button

17. Dusting Brush

18. Height Adjustment

*Varies per model

on-oFF switCH

2.2 Plug cord into electrical outlet.

To turn vacuum ON, push ON/OFF switch once.

To turn vacuum OFF, push switch again.

Technical line drawing of a mechanical clamp or bracket assembly (no text or symbols)

CoRd stoRaGe

2.3 Wrap cord on cord hooks for convenient storage.

Attach the plug end to the cord.

Diagram of a vacuum cleaner with motion arrows indicating airflow or vibration (no text or symbols)

CaRPet HeiGHt adJustMent

2.4 HI BASE RUSH DOWN AND TURN A

2.4 To adjust height setting, PUSH DOWN and TURN knob (A) to desired height setting.

For maximum cleaning performance, the following carpet height settings are recommended:

• Lowest setting: for all types of carpet bare floors.
• Higher settings: for very deep pile car where easier pushing effort is desired, while maintaining good cleaning performance.

- IMPORTANT -

If the vacuum is difficult to push, push down and turn knob to the next higher setting.

3. tools

Tools allow for cleaning surfaces above the floor and for reaching hard to clean areas.

The vacuum is ready for tool use when handle is in upright position.

• IMPORTANT •

Brushroll continues to turn while product is turned on and handle is in upright position unless vacuum is in "Suction Only Mode" (available on select models only). To avoid damage to carpet, rugs, furniture and flooring, avoid tipping cleaner or setting it on furniture, fringed area rugs, or carpeted stairs during tool use.

seleCt PRoPeR tool

(Tools may vary per model)

3.1 A B C

A. Dusting Brush may be used on table tops, books, lighting fixtures, and blinds. (Tool varies per model)
B. Wand is used to give extra length to your hose. Use it with any of the above tools.
C. Crevice Tool may be used in tight spaces, corners and along edges in such places as dresser drawers, upholstered furniture, stairs and baseboards.

ReMoVinG Hose

Line drawing of a person using a vacuum cleaner (no text or symbols)

To remove hose for tool use, press the hose release button and pull hose end out.

To lock back into place, push hose into hose tube until you hear a click.

attaCH wand and tools

3.3

To attach tool or wand to hose, push firmly into place.

staiR CleaninG

3.4 Lift vacuum by Stair Cleaning Handle and position on stairs. Clean forward to back. Never leave the vacuum standing on stairs when not cleaning.

CAUTION

Use extra care when cleaning on stairs. To avoid personal injury or damage, and to prevent the cleaner from falling, always place cleaner at bottom of stairs on floor. Do not place cleaner on stairs or furniture, as it may result in injury or damage.

Line drawing of a person using a tool on stairs, no text or symbols present

How to Clean tools

To clean Hose=1, wipe with a damp cloth. DO NOT submerge in water.

Other cleaning tools may be washed in warm water with a detergent. Rinse and air dry 24 hours before using.

4. MAINTENANCE

Familiarize yourself with these home maintenance tasks as proper use and care of your vacuum will ensure continued cleaning effectiveness.

4.1 The System Check Indicator located at (A), alerts you to possible system performance issues.

If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, take it to a service center prior to continuing use

4.1 A

PROBLEM POSSIBLE CAUSE POSSIBLE SOLUTION
If System Check Indicator is red:	1. Rinsable filter and/or filter made with HEPA media is dirty.	1. Clean rinsable filter and/or filter made w HEPA media - reference pg. 9
	2. Dirt cup is full and/or clogged.	2. Empty dirt cup - reference pg. 9
	3. Brushroll and/or hose is clogged.	3. Check hose for clogging - reference pg 11. Check brushroll for clogging - reference pg. 11.

Any other servicing should be done by an authorized service representative.

▲ NOTICE ▲

A Thermal Protector has been designed into your cleaner to protect it from overheating. When the thermal protector activates the cleaner will stop running.

If this happens proceed as follows:

1. Turn cleaner OFF and unplug it from the electrical outlet.
2. Empty dirt cup.
3. Inspect and remove blockage along the dirt path. This blockage may occur at the: nozzle inlet, hose connector, hose, dirt cup inlet, cyclonic filter, Rinsable filter, and HEPA filter.
4. When cleaner is unplugged and motor cools for 30 minutes, the thermal protector will deactivate and cleaning may continue.

If the thermal protector continues to activate after following the above steps, your cleaner needs servicing.

DIRT CUP

When to Empty

4.2 To maintain optimal performance, empty the dirt cup before the dirt cup reaches the max line (A). Place the vacuum in the upright position before removing the dirt cup.

4.2 A

CAUTION

To reduce the risk of injury from moving parts - Unplug vacuum before servicing. Do not use vacuum without dirt cup or filters in place.

Very fine materials, such as face powder or cornstarch, may seal the filter and cause a reduction in performance. When using the vacuum for this type of dust, empty the cup and clean the filters often.

DIRT CUP

How to Empty

4.3 Press dirt cup release button (A) and pivot cup out.

4.4 Hold dirt cup over trash receptacle, push dirt cup door release lever (B) to open dirt cup door (C).

Close dirt cup door (C). Press firmly to secure at front (D).

4.5 Place bottom of dirt cup into vacuum body first. Pivot dirt cup into vacuum body and press firmly until it locks into place.

4.3 A

4.4 B C D

Line drawing of a hand using a vacuum cleaner to handle a component, labeled with number 4.5 (no text or symbols on the diagram itself)

FILTERS: When to Clean

To maintain optimal performance, filters should be cleaned at least every two months under normal use.

Rinsable Filter: How to Clean

Remove dirt cup as described in Fig. 4.3.

4.6 Pull up on dirt cup latch (A) to open.

4.7 Pull on the filter to remove Rinsable Filter.

Hold filter under running water for two minutes to remove dirt and debris. Squeeze filter twice while underwater. Remove from water and squeeze a final time to remove excess water.

- IMPORTANT -

Allow filter to dry completely before replacing. Dry filter on edge so air circulates on both sides of filter. This may take up to 24 hours.

Replace filter, tab side out.

Close lid securely by pushing at (B) until it clicks as shown in Fig. 4.6.

Replace dirt cup as described in Fig 4.5.

CAUTION

To reduce the risk of injury from moving parts - Unplug vacuum before servicing. Do not use vacuum without dirt cup or filters in place.

4.6 B A

Line drawing of a hand placing a container into a container with a lid, labeled '4.7' (no text or symbols on the diagram itself)

What to Buy: Rinsable Filter

When used and maintained properly, your Rinsable Filter should not need replacement within the warranty period. If desired, additional filter is available at Hoover.com or call 1-800-944-9200. Ask for Hoover® Part No.303173001.

Filter Made With HEPA Media: How to Clean

4.8 With fingers in slots, pull filter frame (A) straight out. Hold filter over a trash receptacle and tap out dirt and debris.

Slide back into position on vacuum.

CAUTION

To reduce the risk of injury from moving parts - Unplug vacuum before servicing. Do not use vacuum without dirt cup or filters in place.

- IMPORTANT -

DO NOT RINSE OR WASH THE FILTER MADE WITH HEPA MEDIA.

What to Buy: Filter Made With HEPA Media

When used and maintained properly, your Filter should not need replacement within the warranty period. If desired, additional filter is available at Hoover.com or call 1-800-944-9200. Ask for Hoover® Part No. 303172001.

4.8 A

Cyclonic Filter Assembly: How to Clean

CAUTION

To reduce the risk of injury from moving parts - Unplug vacuum before servicing.

Do not use vacuum without dirt cup or filters in place.

Remove dirt cup as described in Fig. 4.3.

4.9 Twist filter assembly (A) counterclockwise. Remove assembly from dirt cup.
4.10 Dirt and debris can be cleaned from the filter assembly with the Dusting/ Upholstery Tool.
4.11 Place the filter assembly on the dirt cup, aligning (3) tabs (A) on filter with (3) slots on dirt cup (B) and twist it clockwise to secure into position.
4.12 The Hoover ^® emblem and center lines on the dirt cup should align on the front of the dirt cup (C) if assembled correctly.

4.9 A

4.11 A B

Line drawing of a hand holding a mechanical component, no text or symbols present

4.12 C

Replace dirt cup as described in Fig. 4.5.

BRUSHROLL: How to Clean

CAUTION

To reduce the risk of injury from moving parts - Unplug vacuum before servicing.

4.13 Turn vacuum over so bottom side is facing up. Rotate red upper latch (A) counterclockwise.
4.14 Slide red lower latch (B) to the unlock position.
4.15 Pivot out bottom plate and remove any debris and/or hair from brushroll.
4.16 Reposition bottom plate, aligning the three tabs along front edge of nozzle guard with the three slots in nozzle. Rotate back into position. Slide red lower latch to Lock position, and rotate red upper latch clockwise.

4.13 A

4.14 B

Line drawing of a mechanical device with a hand operating it, no text or symbols present

4.16

HOSE: How to Clean

CAUTION

To reduce the risk of injury from moving parts - Unplug vacuum before servicing.

4.17 To remove hose for tool use, press the hose release button (A) and pull hose end out.

Clear away debris or obstructions from hose. Do not use sharp objects to clean out hose as they can cause damage. To lock back into place, push hose into hose tube until you hear a click.

4.17 g. A

BELT

CAUTION

To reduce the risk of injury from moving parts - Unplug vacuum before servicing.

The belt is located under the bottom plate of the vacuum and should be checked from time to time to be sure it is in good condition.

When To Replace

Replace belt if it is stretched, cut or broken. To check the belt, refer to Fig. 4.18 - 4.20.

How To Replace

4.18 Turn vacuum over so bottom side is facing up. Rotate red upper latch (A) counter clockwise.
4.19 Slide red lower latch (B) to the unlock position. 4.20 Lift off bottom plate.
4.21 Remove used belt from brushroll (C) then from motor shaft (metal rod) (D) and discard.

4.18 A

4.19 B

Technical line drawing of a mechanical device with a hand operating it (no text or symbols)

4.21 D C

BELT (continued)

What to Buy: Belt

Use only genuine HOOVER® belts with your vacuum.

When purchasing a new belt, ask for Stretch Belt - HOOVER® part No. 562932001 or AH20080.

4.22 With lettering on outside of belt, slide new belt over motor shaft (metal rod) (E).

Push other end of belt through belt guide (F) and then slip around area of brushroll without bristles (G).

With belt in place, pull and slide brushroll into nozzle making sure that the brushroll end caps are in the correct orientation.

4.29 Reposition bottom plate, aligning the three tabs along front edge of nozzle guard with the three slots in nozzle. Rotate back into position. Slide red lower latch to Lock position, and rotate red upper latch clockwise to secure bottom plate.

*Models without "Suction Only Mode" do not have the metal pulley

4.22 E F G

4.23

- IMPORTANT -

Rotate brushroll manually to make sure belt is not twisted.

5. tRouBlesHootinG

If a minor problem occurs, it usually can be solved quite easily when the cause is found by using the checklist below.

Any other servicing should be done by an authorized service representative.

If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, take it to a service center prior to continuing use.

▲ WARNING ▲

To reduce risk of personal injury - Unplug vacuum before servicing.

PRoBleM Possible Cause Possible solution
Vacuum won't run	1. Power cord not firmly plugged into outlet. 1. Plug unit in firmly.2. Blown fuse or tripped breaker. 2. Check fuse or breaker in home. Replace fuse/reset breaker in home.3. Thermal Protector activated. 3. Unplug and allow vacuum to cool for 30min.(This willl reset the thermal protector)
System Check Indicator has turned red or Vacuum won't pick up or Low suction	1.Rinsable Filter and/ or Filter made with HEPA media is dirty.2. Dirt cup full and/ or clogged. 2. Empty dirt cup - Pg. 9.3. Broken or worn belt. 3. Replace belt - Pg.12.4. Brushroll and/ or Hose clogged. 4. Check Hose - Pg. 11. Check Brushroll - Pg.11.5. Carpet height setting is incorrect. 5. Set Carpet Height Adjustment to appropriate setting for carpet being cleaned - Pg.7.	1. Clean Rinsable Filter and or Filter made with HEPA media - Pg. 9 and 10.
Dust escaping from vacuum	1. Dirt cup full. 1. Empty dirt cup - Pg. 9.2. Dirt cup not installed correctly. 2. Review Dirt Cup removal & replacement - Pg. 9.3. Hose not installed correctly.4. Rinsable and/ or Filter made with HEPA media not installed completely.	3. Review Hose installation - Pg. 7.4. Review Filter Removal and Cleaning - Pg. 9 and 10.
Vacuum is difficult to push or won't move forward	1. Carpet height setting is incorrect.	1. Set Carpet Height Adjustment knob to appropriate setting for carpet being cleaned - Pg. 7.
Smoky/burning smell detected	1. Belt broken or stretched.2. Brushroll is clogged. 2. Clear/ remove debris from brushroll - Pg. 11.	1. Replace brushroll belt - Pg. 13.

6. seRViCe

To obtain approved Hoover® service and genuine Hoover® parts, locate the nearest Authorized Hoover® Warranty Service Dealer (Depot) by:

• Checking the Yellow Pages under "Vacuum Cleaners" or "Household".
• Visit our website at hoover.com (U.S. Customers) or hoover.ca (Canadian customers).
  Follow the service center link to find the service outlet nearest you.
• For an automated referral of authorized service outlet locations call 1-800-944-9200.

Do not send your vacuum to Hoovet, Inc., Company in Glenwillow for service. This will only result in delay.

If you need further assistance:

To speak with a customer service representative call 1-800-944-9200; Mon-Fri 8am-7pm EST. Always identify your vacuum by the complete model number when requesting information or ordering parts. (The model number appears on the bottom of the vacuum.)

limited one YeaR CoMMeRCial ProduCt waRRantY

WHAT THIS WARRANTY COVERS

When used and maintained in normal Commercial use and in accordance with the Owner's Manual, your HOOVER® product is warranted against original defects in material and workmanship for a full one year from date of purchase (the "Warranty Period"). During the Warranty Period, as described in this Warranty, Hoover will provide labor and parts, at no cost to you, to correct any such defect in products purchased in the United States, U.S. Military Exchanges and Canada.

HOW TO MAKE A WARRANTY CLAIM

If this product is not as warranted, take or send the product to a Hoover Authorized Warranty Service Dealer along with proof of purchase. For an automated referral to authorized service outlets, phone: [phone] OR visit Hoover online at www.hoover.com (U.S. Customers) or www.hoover.ca (Canadian Customers). For additional assistance or information concerning this Warranty or the availability of warranty service outlets, phone [phone], Mon-Fri 8am-7pm EST. In Canada, call 1-800-263-6376, Mon-Fri 8am-7pm EST.

WHAT THIS WARRANTY DOES NOT COVER

Certain parts for your Hoover Commercial product require replacement in the ordinary course of use due to normal wear. These items include belts, agitator roll sleeves, agitator bearings, brushes, bags, filters and bulbs. These parts are not covered by this Warranty.

This Warranty also does not cover: improper maintenance of the product, damage due to misuse, acts of God, nature, vandalism or other acts beyond the control of Hoover, owner's acts or omissions, use outside the country in which the product was initially purchased, resale of the product by the original owner, defects or damages caused by repair or alteration by anyone other than an Authorized Hoover Warranty Service Dealer. Hoover, Inc. reserves the right to inspect any alleged defective product and make final decisions on any warranty claim.

This warranty does not cover pick up, delivery, transportation or house calls. However, if you mail your product to a Hoover Authorized Warranty Service Dealer for warranty service, cost of shipping will be paid one way.

OTHER IMPORTANT TERMS

This Warranty is not transferable and may not be assigned. This Warranty shall be governed and construed under the laws of the state of Ohio. The Warranty Period will not be extended by any replacement or repair performed under this Warranty.

THIS WARRANTY IS THE EXCLUSIVE WARRANTY AND REMEDY PROVIDED BY HOOVER. ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE, ARE DISCLAIMED. IN NO EVENT WILL HOOVER BELIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND OR NATURE TO OWNER OR ANY PARTY CLAIMING THROUGH OWNER, WHETHER BASED IN CONTRACT, NEGLIGENCE, TORT OR STRICT PRODUCTS LIABILITY OR ARISING FROM ANY CAUSE WHATSOEVER. Some states do not allow the exclusion of consequential damages, so the above exclusion may not apply to you. This warranty gives you specific rights; you may also have others that vary from state to state.

Line drawing of a vacuum cleaner with handle and base (no text or symbols)

iMPoRtante: lea atentaMente antes de ensaMBlaR Y usaR.

2 D F E G

Line drawing of a mechanical device with a cylindrical top and base (no text or symbols)

D

C

E

F

G

ColoCaCión del ManGo

Diagram showing a hand holding a tool with an arrow indicating downward motion, next to a small mechanical component (no text or symbols)

1.3

Line drawing of a hand holding a tool near a curved mechanical part (no text or symbols)

Line drawing of a hand using a vacuum cleaner to clean or store items (no text or symbols visible)

Technical line drawing of a mechanical clamp or bracket assembly (no text or symbols)

GuaRdaR el CoRdón

Diagram of a mechanical device with motion arrows indicating rotational motion (no text or symbols)

aJuste de la altuRa PaRa alFoMBRas

Line drawing of a vacuum cleaner's seat and legs (no text or symbols)

Line drawing of a person using a tool to lift a small object, with no visible text or symbols

Technical line drawing of a mechanical component with no visible text or symbols

Line drawing of a hand using a vacuum cleaner to handle a cylindrical component (no text or symbols)

Line drawing of a hand pressing down on a cylindrical object (no text or symbols)

Line drawing of a hand holding a mechanical component, no text or symbols present

Line drawing of a mechanical device with a hand operating it, no text or symbols present

4.14 B

4.16

Line drawing of a mechanical device with a hand operating it, no visible text or symbols

4.19 B

4.21 D C

CORREA (continuado)

Qué comprar: Correa plana

4.22 E F G

4.23

Line drawing of a vacuum cleaner with handle and base (no text or symbols)

Vide-poussière ....8

Filtres 9

Rouleaubrosse ....11

Tuyau ....11

Courroie ....11

Dépannage ....13

Service....13

Garantie....14

2 D F E G

Diagram showing a hand holding a tool with an arrow pointing to a small mechanical component (no text or symbols present)

1.3

Line drawing of a hand holding a tool next to a curved mechanical component (no text or symbols)

Line drawing of a person using a vacuum cleaner (no text or symbols present)

installeR les aCCessoiRes

Technical line drawing of a mechanical assembly with no visible text or symbols

entRetien du CoRdon

Diagram of a mechanical device with motion arrows indicating rotational motion (no text or symbols)

For maximum cleaning performance, the following carpet height settings are recommended:

Line drawing of a vacuum cleaner's leg and foot assembly (no text or symbols)

Line drawing of a hand using a pliers to cut or install a piece of wood, no text or symbols present

Line drawing of a person using a vacuum cleaner on a lift (no text or symbols)

Line drawing of a hand placing a container into a cylindrical container (no text or symbols)

Quoi acheter : Filtre lavable

Line drawing of a hand holding a mechanical component, no text or symbols present

Technical line drawing of a mechanical device with labeled component 'C' (no text or symbols beyond label)

Line drawing of a mechanical device with a hand operating it, no text or symbols present

Diagram of a mechanical device with internal components and directional arrows, no visible text or symbols

4.22 E F G

4.23

- IMPORTANT -