CD406 - Food Processor BUFFALO - Free user manual and instructions

USER MANUAL CD406 BUFFALO

Model . Modéle . Modell . Modello . Modelo . Malli CD406UK Safety Tips Position on a flat, stable surface. A service agent/qualified technician should carry out installation and any repairs if required. Do not remove any components on this product. Consult Local and National Standards to comply with the following: o Health and Safety at Work Legislation o BS EN Codes of Practice o Fire Precautions o IEE Wiring Regulations o Building Regulations DO NOT immerse the appliance in water. Do not use the appliance for anything other than its intended use. Always switch off and disconnect the power supply to the appliance when not in use. Not suitable for outdoor use. Keep all packaging away from children. Dispose of the packaging in accordance to the regulations of local authorities. If the power cord is damaged, it must be replaced by a BUFFALO agent or a recommended qualified technician in order to avoid a hazard. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance Do not let cord hang over edge of table or counter, or touch hot surfaces Keep hands and utensils out of the jug while motor is running to prevent severe personal injury and / or damage to the blender Blade is sharp – handle carefully Never try to remove blade while jug is sitting on the blender base Do not operate with loose or damaged blades Do not place jug on to base with On/Off switch in the On position Always operate with lid in place Do Not blend Hot Liquids. Do not leave blender unattended while in use Introduction Please take a few moments to carefully read through this manual. Correct maintenance and operation of this machine will provide the best possible performance from your BUFFALO product.Telephone Helpline: 0845 146 2887 (United Kingdom) Pack Contents The following is included: BUFFALO Blender Blender Jug and lid Safety pusher BUFFALO prides itself on quality and service, ensuring that at the time of packaging the contents are supplied fully functional and free of damage. Should you find any damage as a result of transit, please contact your BUFFALO dealer immediately. Location of Controls

Controls 1 – On / OFF switch. Up for On, down for Off. 2 – Variable Speed Dial. Allows continual adjustment of speed from low (10,000rpm) to high (22,000rpm) 3 – High/Low Pulse Switch Down to pulse at high speed (22,000rpm).UK Operation Plug in Blender and turn on Power Switch (located on side of machine). The machine is now ready for use. To blend using variable speed function –

1. Place ingredients into blender

2. Secure lid (Note. Always operate with lid secured)

3. Locate jug on to body of blender

4. Select speed using variable speed dial (low 10,000rpm, high 22,000rpm)

1. Place ingredients into Blender

2. Secure lid (Note. Always operate with lid secured)

3. Locate jug on to body of Blender

4. Turn on blender using Pulse switch (Up to Pulse at high speed (22,000rpm), down to Pulse at low speed

(10,000rpm) Note – When blending dry ingredients best results will be obtained by cutting ingredients’ in to small pieces and adding to the blender when motor is running using the hole in the lid. Cleaning, Care & Maintenance

Always disconnect from power supply before cleaning

Always allow to cool before cleaning.

Use warm, soapy water and a damp cloth to clean the appliance.

Dry thoroughly after cleaning.

A BUFFALO dealer or qualified technician should carry out repairs if required. WARNING: Do not allow any water to spill into the body of the appliance when cleaning.Telephone Helpline: 0845 146 2887 (United Kingdom) Troubleshooting Fault Probable Cause Action The unit is not working The Unit is not switched on Check the unit is plugged in correctly and switched on Plug and lead are damaged Call BUFFALO agent or qualified technician Fuse in the plug has blown Replace the plug fuse Power supply Check Power Supply Internal wiring fault Call BUFFALO agent or qualified technician Unit has overheated Allow to cool. When cool press reset switch located on base Jug incorrectly located on body of appliance Relocate Jug NOTE: Jug / Blades are not covered by manufacturers warranty

Electrical Wiring This appliance is supplied with a 3 pin, moulded, BS1363 plug and lead, with a 13 amp fuse as standard. The plug is to be connected to a suitable mains socket. This appliance is wired as follows:

• Live wire (coloured brown) to terminal marked L

• Neutral wire (coloured blue) to terminal marked N

• Earth wire (coloured green/yellow) to terminal marked E This appliance must be earthed, using a dedicated earthing circuit. If in doubt consult a qualified electrician. Electrical isolation points must be kept clear of any obstructions. In the event of any emergency disconnection being required they must be readily accessible.UK Compliance The WEEE logo on this product or its documentation indicates that the product must not be disposed of as household waste. To help prevent possible harm to human health and/or the environment, the product must be disposed of in an approved and environmentally safe recycling process. For further information on how to dispose of this product correctly, contact the product supplier, or the local authority responsible for waste disposal in your area. BUFFALO parts have undergone strict product testing in order to comply with regulatory standards and specifications set by international, independent, and federal authorities. BUFFALO products have been approved to carry the following symbol: