UCC15NPRII - Ice machine GE - Free user manual and instructions

USER MANUAL UCC15NPRII GE

Write the model and serial numbers here: Model # _________________ Serial # _________________ Find these numbers on a label on the top inner case liner of the unit toward the front. GE is a trademark of the General Electric Company. Manufactured under trademark license.

AND INSTALLATION INSTRUCTIONS ICE MACHINE 49-1000640 Rev. 0 12-21 GEA UCC15NP

• TROUBLESHOOTING TIPS p. 23
• LIMITED WARRANTY p. 26
• ACCESSORIES p. 27
• CONSUMER SUPPORT 49-1000640 Rev. 0 THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME. Whether you grew up with GE Appliances, or this is your first, we’re happy to have you in the family. We take pride in the craftsmanship, innovation and design that goes into every GE Appliances product, and we think you will too. Among other things, registration of your appliance ensures that we can deliver important product information and warranty details when you need them. Register your GE appliance now online. Helpful websites and phone numbers are available in the Consumer Support section of this Owner’s Manual. You may also mail in the pre-printed registration card included in the packing material.49-1000640 Rev. 0 3 SAFETY INFORMATION p. 282

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE INSTALLATION WARNING EXPLOSION HAZARD Keep flammable materials and vapors, such as gasoline, away from appliance. Failure to do so can result in fire, explosion, or death. WARNING To reduce the risk of fire, explosion, electric shock, or injury when using your ice machine, follow these basic safety precautions:Ŷ 7KLV,FHPDFKLQHPXVWEHSURSHUO\LQVWDOOHGDQGORFDWHGLQDFFRUGDQFHZLWKWKH,QVWDOODWLRQ,QVWUXFWLRQVEHIRUHLWLVXVHGŶ 8QSOXJWKH,FHPDFKLQHEHIRUHPDNLQJUHSDLUVreplacing a light bulb, or cleaning. NOTE:3RZHUWRWKH,FHPDFKLQHFDQQRWEHdisconnected by any setting on the control panel. NOTE: Repairs must be performed by a qualified Service Professional.Ŷ 5HSODFHDOOSDUWVDQGSDQHOVEHIRUHRSHUDWLQJŶ 'RQRWXVHDQH[WHQVLRQFRUGŶ 'RQRWVWRUHRUXVHJDVROLQHRURWKHUIODPPDEOHvapors and liquids in the vicinity of this or any other appliance.Ŷ 'RQRWVWRUHH[SORVLYHVXEVWDQFHVVXFKDVDHURVROcans with a flammable propellant in this appliance.Ŷ 7RSUHYHQWVXIIRFDWLRQDQGHQWUDSPHQWKD]DUGVWRFKLOGUHQUHPRYHWKH,FHPDFKLQHGRRUIURPDQ\,FHmachine before disposing of it or discontinuing its use. Ŷ 7RDYRLGVHULRXVLQMXU\RUGHDWKFKLOGUHQVKRXOGQRWstand on, or play in or with the appliance.Ŷ &KLOGUHQDQGSHUVRQVZLWKUHGXFHGSK\VLFDOVHQVRU\or mental capabilities or lack of experience and knowledge can use this appliance only if they are supervised or have been given instructions on safe XVHDQGXQGHUVWDQGWKHKD]DUGVLQYROYHGŶ 7KLVDSSOLDQFHLVLQWHQGHGWREHXVHGLQKRXVHKROGand similar applications such as: staff kitchen areas in shops, offices and other working environments; farm houses; by clients in hotels, motels, bed & breakfast and other residential environments; catering and similar non-retail applications.Ŷ &RQQHFWWRSRWDEOHZDWHUVXSSO\RQO\$FROGZDWHUsupply is required for automatic icemaker operation. The water pressure must be between 30 and 120 psi (207-827 kilopascals).Ŷ 'RQRWDSSO\KDUVKFOHDQHUVWRWKH,FHPDFKLQHCertain cleaners will damage plastic which may cause parts such as the door or door handles to detach unexpectedly. See the Care and Cleaning section for detailed instructions. CAUTION

7RUHGXFHWKHULVNRILQMXU\ZKHQXVLQJ\RXU,FHPDFKLQHIROORZWKHVHEDVLFVDIHW\

precautions.Ŷ .HHSILQJHUVRXWRIWKH³SLQFKSRLQW´DUHDVclearances between the doors and between the doors and cabinet are necessarily small. Be careful closing doors when children are in the area.Ŷ 'RQRWWRXFKWKHFROGVXUIDFHVLQWKHLFHcompartment.Ŷ $YRLGFRQWDFWZLWKPRYLQJSDUWVRIWKHLFHPDNHU4 49-1000640 Rev. 0 Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For personal safety, this appliance must be properly grounded.The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard SURQJJURXQGLQJZDOORXWOHWWRPLQLPL]HWKHSRVVLELOLW\RIHOHFWULFVKRFNKD]DUGIURPWKLVDSSOLDQFHHave the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.Where a standard 2-prong wall outlet is encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet. The ice maker should always be plugged into its own YROW+]DPSFLUFXLW7KLVSURYLGHVWKHEHVWperformance and also prevents overloading house ZLULQJFLUFXLWVZKLFKFRXOGFDXVHDILUHKD]DUGIURPoverheated wires. Never unplug your ice maker by pulling on the power cord. Always grip plug firmly and pull straight out from the outlet.Repair or replace immediately all power cords that KDYHEHFRPHIUD\HGRURWKHUZLVHGDPDJHG'RQRWuse a cord that shows cracks or abrasion damage along its length or at either end.When moving the ice maker, be careful not to roll over or damage the power cord. CONNECTING ELECTRICITY WARNING ELECTRICAL SHOCK HAZARDPlug into a grounded 3-prong outlet'RQRWUHPRYHWKHJURXQGSURQJ'RQRWXVHDQDGDSWHUFailure to follow these instructions can result in death, fire, or electrical shock. SAFETY INFORMATION

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE READ AND SAVE THESE INSTRUCTIONS49-1000640 Rev. 0 5 WARNING SUFFOCATION AND CHILD ENTRAPMENT HAZARDRemove the door from the appliance prior to disposal. Failure to do so can result in child entrapment which can lead to death or brain damage.IMPORTANT: Child entrapment and suffocation are not problems of the past. Junked or abandoned appliances DUHVWLOOGDQJHURXVHYHQLIWKH\ZLOOVLWIRU³MXVWDIHZGD\V´,I\RXDUHJHWWLQJULGRI\RXUROGDSSOLDQFHplease follow the instructions below to help prevent accidents.Before You Throw Away Your Old Appliance:Ŷ Take off the doors.Ŷ Leave the internal components in place so that children may not easily climb inside.

PROPER DISPOSAL OF YOUR OLD APPLIANCE

READ AND SAVE THESE INSTRUCTIONS

instruction labels inside your ice machine or the Tech Sheet that is fastened behind the kickplate.

Ŷ5HPRYHWDSHDQGDQ\ODEHOVIURP\RXULFHPDNHU

before using (except the model and serial number label). To remove any remaining tape or glue, rub the area briskly with your thumb. Tape or glue residue can also be easily removed by rubbing a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry. Ŷ'RQRWXVHVKDUSLQVWUXPHQWVUXEELQJDOFRKRO flammable fluids or abrasive cleaners to remove tape or glue. These products can damage the surface of

\RXULFHPDNHU)RUPRUHLQIRUPDWLRQVHH,PSRUWDQW

6DIHW\,QVWUXFWLRQV Door Alarm An alert will sound when the door has been left open for

PLQXWHV7KHDOHUWVWRSVZKHQGRRULVFORVHG6QRR]H

the alert by pressing any button.

'LVDEOHWKHGRRUDODUPE\SUHVVLQJ³3RZHU´&OHDQDQG

³)LOWHU5HVHW´EXWWRQVDWWKHVDPHWLPH

Sabbath Mode The Sabbath Mode was designed for use on the Jewish Sabbath and Holidays. The icemaker will not make ice

GXULQJWKH6DEEDWKPRGH,I6DEEDWKPRGHLVHQWHUHG

while making ice, icemaker will complete current cycle EHIRUHWXUQLQJRIIOHVVWKDQPLQXWHV,FHPDNLQJ

ZLOOVWDUWDJDLQDWWKHHQGRIWKH6DEEDWKPRGH,IWKH

icemaker is equipped with a drain pump, it will continue to work as normal. The icemaker will exit Sabbath mode automatically after 96 hours. ON/OFF - To activate the Sabbath Mode, Press and KROG³3RZHU´DQG³)LOWHU5HVHW´IRUVHFRQGV7RH[LW 6DEEDWK0RGH3UHVVDQG+ROG³3RZHU´DQG³)LOWHU 5HVHW´IRUVHFRQGV7KH0DNLQJ,FH7LPHWR&OHDQ

will flash until the current icemaking cycle is complete prior to turning off. The icemaker will also drain

2. CLEAN - Press and hold for 3 seconds to start the cleaning process. (See Care and Cleaning)

3. FILTER RESET - Press after changing filter to reset filter timer. (See XWFE Water Filter)

4. WiFi - Press and hold Clean and Filter buttons at the same time. WiFi symbol will start blinking. (See Wifi section)

6 months indicating it is time to clean the machine. (See Care and Cleaning)

7. Replace Filter ,QGLFDWRUZLOOLOOXPLQDWHZKHQLWLVWLPHWRRUGHUDILOWHU,QGLFDWRUZLOOIODVKZKHQLWLVWLPHWRUHSODFH

the filter. (See XWFE Water Filter) Packaging USING THE ICE MACHINE: Packaging/ Controls

Controls49-1000640 Rev. 0 7 Regulatory Information FCC/IC Compliance Statement: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received,

including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will QRWRFFXULQDSDUWLFXODULQVWDOODWLRQ,IWKLVHTXLSPHQW does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna. ,QFUHDVHWKHVHSDUDWLRQEHWZHHQWKHHTXLSPHQWDQG receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/television technician for help. Labelling: Changes or modifications to this unit not expressly approved by the manufacturer could void the user’s authority to operate the equipment. Appliance Communication WiFi (for customers in the United States, its territories, and Canada)

'RZQORDGWKH6PDUW+4DSS

• Available for iPhone from the Apple Store or from link at GEAppliances.com.

• Available for Android from Google Play or from link at GEAppliances.com. Select Create Account on app.

• Enter information, and select Register. An e-mail will be generated.

• When you receive the e-mail, select Verify Account.

6LJQLQZLWK\RXUFUHGHQWLDOVDQGVHOHFW$XWKRUL]HWR

allow the app to communicate with your icemaker. Set up the app.

• Press the at the top of the screen.

• The info button will show a picture of the touch display on the appliance. Select OK.

• Select Next. Press WiFi Connect on the control. Press and hold Clean and Filter buttons at the same time The WiFi symbol will start flashing on the display.

• Select Next in the app.

'RRUDWWKHERWWRPRIWKH,FH0DNHU

• Enter the password into the app. &RQQHFWWRWKH,FHPDNHU¶V:L)L0RGXOHLQWKHSKRQH¶V

Filter Access cover below the ice storage bin.

• Connect to the home WiFi network and type in the home WiFi password. ,IDOOFKHFNPDUNVDSSHDUDQGWKHXVHUJHWVDVFUHHQ that says the device is connected, the device has been successfully connected.

possible reasons why connection failed and the option to retry. Controls USING THE ICE MACHINE: Packaging/ Controls8 49-1000640 Rev. 0 Starting the ice machine ,FHVFRRS Light Water filter Kick Plate

&RQQHFWHG$SSOLDQFH,QIRUPDWLRQ/DEHO

Control panel Water filter access door Initial Start Up

1. Turn on the water supply.

2. Switch on the electrical power.

4. Water will begin to flow into the unit. When the

reservoir is full, water will start to drain from the machine. After a few minutes the compressor, water pump and fan motor will begin to operate as the first ice making cycle begins.

,QDSSUR[LPDWHO\PLQXWHVLFHZLOOIDOOLQWRWKHLFH

storage bin. The machine makes 24 cubes at a time. ,WLVQRUPDOIRUWKHILUVWEDWFKHVRILFHWRPHOWDVWKH ELQFRROV,WZLOOWDNHKRXUVRIFRQWLQXRXVUXQ time to fill the ice bin. When the ice bin is full, the ice

PDFKLQHZLOOVKXWRII,WZLOODXWRPDWLFDOO\UHVWDUWZKHQ

the ice level falls, either from use or normal meltage. 'LVFDUGWKHILUVWELQIXOORILFH Features USING THE ICE MACHINE: Features/ Starting the ice machine This machine takes in room temperature air at the lower right front and forces warm air out the lower left front. Restricting the airflow or operating the machine in a hot or cold environment will adversely affect the ability of the ice machine to make ice. When the door is opened, the control panel, ice making area and ice storage bin are visible. The scoop is located in a holder on the inside of the door. This is a gravity drain model that must have a building drain connection below the level of the drain tube at the back of the cabinet. A pump can be installed, which can force drain water up a maximum of 8 feet, allowing it to be located where a gravity drain isn't available. See Accessories on page 27 for more information on the drain pump. Warm Air Out $LU,QWDNH49-1000640 Rev. 0 9

GROUNDING THE ICE MACHINE

WARNING Electrical Shock Hazard. Failure to follow these instructions can result in death, fire, or electrical shock.The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard SURQJJURXQGLQJZDOORXWOHWWRPLQLPL]HWKHSRVVLELOLW\RIHOHFWULFVKRFNKD]DUGIURPWKLVDSSOLDQFHHave the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.Where a standard 2-prong wall outlet is encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet. '212781'(5$1<&,5&8067$1&(6&87255(029(7+(7+,5'*5281'3521*)5207+(32:(5&25''212786($1$'$37(53/8*72&211(&77+($33/,$1&(72$3521*287/(7'212786($1(;7(16,21&25':,7+7+,6$33/,$1&(Questions? Call 800.GE.CARES (800.432.2737) or visit our Website at: GEAppliances.com In Canada, call 1.800.561.3344 or visit our Website at: GEAppliances.ca

Read these instructions completely and carefully.

• IMPORTANT — Observe all governing codes and ordinances. Save these instructions for local inspector’s use.
• Note to Installer – Be sure to leave these instructions with the Consumer.• Note to Consumer – Keep these instructions for future reference.• Skill level – ,QVWDOODWLRQRIWKLVDSSOLDQFHUHTXLUHVbasic mechanical skills.
• Completion time – ,QVWDOODWLRQFDQYDU\ :DWHU/LQH,QVWDOODWLRQminutes• Proper installation is the responsibility of the installer. • Product failure due to improper installation is not covered under the Warranty.

ICE MACHINE LOCATION AND

PREPARATION This ice machine is designed to be used indoors, in a controlled environment.,WLVPDGHXSRIWZRPDMRUV\VWHPVWKHLFHPDNLQJsystem and the ice storage system. The ice making system makes ice when the ice level becomes low and stops when it is full.The ice storage system is an insulated chest ZLWKDGUDLQDWWKHERWWRPIRUPHOWLQJLFH,WLVQRWrefrigerated, insuring that the bin contains fresh ice.IMPORTANT: Never keep anything in the ice storage bin that is not ice. Objects like wine or beer bottles are not only unsanitary, but the labels can slip off and plug up the drain.IMPORTANT: Never allow the machine to operate without regular cleaning. The machine will last longer if it is kept clean. Regular cleaning should happen twice per year. Some water conditions will dictate even more frequent cleaning of the ice making section, and some carpets or pets will dictate more frequent cleaning of the condenser.SpecificationsThe ice machine will operate adequately within the limits, but functions best in temperatures between 60°F and 80°F.• Minimum air temperature: 55°F (12.8°C)• Maximum air temperature: 100°F (38°C)• Minimum water temperature: 40°F (4.5°C)• Maximum water temperature: 90°F. (32°C)• Minimum water pressure: 30 psi (2.07 bar)• Maximum water pressure: 120 psi (8.27 bar)Electrical voltage limits:See the Rating Plate inside the ice machine. INSTALLATION INSTRUCTIONS Installation Instructions ICE MACHINE10 49-1000640 Rev. 0 Installation Instructions INSTALLATION INSTRUCTIONS ICE MACHINE LOCATION AND PREPARATION (Cont.) Utility and Operational Requirements

• This ice machine must be connected to a potable water supply.All water, including potable water supplied by municipalities, contains some impurities or minerals. Water absorbs impurities from the air as rain and/or as it flows through the ground. Some of the impurities are solid particles. These are known as suspended solids, and a fine particle filter will remove them. Other impurities are chemically bonded to the water molecules and cannot be filtered out. These are called dissolved solids. ,FHPDGHE\WKLVPDFKLQHZLOOKDYHDORZHUPLQHUDOcontent than the water it was made from. This is due WRWKHPHWKRGRIPDNLQJLFH3XUHUZDWHUZLOOIUHH]Hfirst in the ice making molds. The reason for this is that anything dissolved in water lowers the water's IUHH]LQJWHPSHUDWXUH7KLVFRQFHQWUDWHVPRVWRIWKHimpurities of the ice machine water reservoir where they may form hard deposits known as scale. The machine dilutes the concentration of minerals by over-filling the reservoir during the harvest cycle (with the excess water flowing down the drain). Water use varies with air and water temperatures. Some impurities will inevitably remain, and will stick to the parts in the machine. This will cause malformed ice cubes. Eventually, built up mineral scale can shorten machine life. To keep the machine operating properly, these impurities or minerals will have to be regularly GLVVROYHGE\DQDFLGFOHDQHU'LUHFWLRQVIRUWKLVPD\be found in the Care and Cleaning section.This machine can be supplied with Reverse Osmosis water, but the water conductivity must be no less than 10 microSiemens/cm. A reverse osmosis system should include post treatment or blending to satisfy the R.O. water's potential aggressiveness.'HLRQL]HGZDWHULVQRWUHFRPPHQGHGDQGFRXOGdamage the machine.Because water softeners exchange one mineral for another, softened water may not improve water conditions when used with ice machines. 0LQLPXPUHFRPPHQGHGFOHDUDQFHVRQVLGHVRQWRSLQEDFN• Minimum water pressure: 30 psi• Maximum water pressure: 120 psi• Minimum water temperature: 40°F• Maximum water temperature: 90°F.This ice machine is designed to operate in a wide range of air temperatures with a minimum air temperature of 55°F and a maximum air temperature of 100°F.Although the machine will function within the listed ranges, it works best at water temperatures between 50°F and 60°F and air temperatures between 60°F and 80°F.Operating a unit outside of the limits can cause problems that are not covered by the warranty and, if extreme, cause damage to the unit.7KLVPDFKLQHFDQEHEXLOWLQWRDFDELQHW,WLVDQair cooled refrigeration system. Air flows in and out of it through the grill at the bottom front. The grille must not be blocked by any covering door, or other obstruction.49-1000640 Rev. 0 11 ADVANCE PLANNING CAUTION Due to excessive weight, TWO PEOPLE ARE REQUIRED TO MOVE AND INSTALL THIS Ice maker. Failure to do so can result in back or other injury.Cutout & Product DimensionsInstallation NotesA drain pump is available for this ice machine. The GUDLQSXPSNLWQXPEHULV83.DQGLVDYDLODEOHDWGEApplianceparts.com or by calling 877-959-8688. ,Q&DQDGDYLVLW GEAppliances.ca or call 800.561.3344.Built-In Installation:,IDILQLVKHGIORRULVWREHLQVWDOOHGin the area after the ice machine has been built in, shims the expected thickness of the floor should be installed under the unit to keep the machine level with the planned floor level.NOTE: The water connection is at the back and adds a few inches to the cabinet depth.Installation on a slab: You will need to install a drain pump to the appliance and pump the water to the point of drainage. See Accessories. Pumps will pump up to 8 feet high.Installation over a crawl space or basement: Either a gravity drain or a pump may be used. For pump, see Accessories,IWKHUHLVQRWHQRXJKURRPEHKLQGWKHmachine for a drain/waste receptacle, the drain will have to be below the floor. NOTE: When installed in a corner, the door swing may be limited due to handle contact with the wall or cabinet face.A water supply is required. Water supplies vary in the degree of mineral content. High mineral content water will require more frequent maintenance. Water filtration may improve the taste of the ice as well as cut down on some of the mineral build up.15"(38.1 cm)34-1/8" min.Adjustable to34-7/8"34-1/2" min.to 35"20-3/8"3-7/8"*3-5/8"3/4"24"cabinetdepthCounter-topoverhangStainless exteriordoor dimension.(cutom panelsize may vary)*Reference dimension.Assumes front of doorwithout exterior panelaligns with front ofcabinet as shown.Floor drainaccess hole Installation Instructions INSTALLATION INSTRUCTIONS12 49-1000640 Rev. 0 Water inlet:1/4" DIMENSIONS Installation Instructions INSTALLATION INSTRUCTIONS 3 7/8" 20 3/8" FLOOR DRAIN ACCESS HOLE49-1000640 Rev. 0 13 DOOR SWING Moving the hinges allows the door to open from either the left or the right side. Change the swing BEFORE attaching the door panel.

1. Remove the top and bottom hinge screw covers to

gain access to the screws.

2. Remove the hinge screws (4 total for top and

4. Remove the door gasket and ice scoop .

8VH D VORWWHG VFUHZGULYHU WR SU\ RQ WKH VQDSV RQ the lower decorative cover at the 4 location shown in the figure.

6. Remove the upper decorative cover in the same way.

7. Remove the top hinge and hinge cover. Remove

the hinge cover from the hinge.

8. Remove the lower hinge and hinge cover. Remove

the hinge cover from the hinge.

9. Slide the original top hinge cover on the original

lower hinge and attach this assembly to the top, on the opposite side of the original location.

10. Slide the original lower hinge cover on the original

top hinge and attach this assembly to the lower hinge location, on the opposite side for the original location. Installation Instructions INSTALLATION INSTRUCTIONS Steps 8-11Remove

Push to Release14 49-1000640 Rev. 0 DOOR SWING (Cont.)

11. Remove any plastic protective covering from the

stainless door panel

8VLQJD3KLOOLSVVFUHZGULYHULQVWDOOWKHVL[VFUHZV

(supplied with door panel kit) as shown in the figure to attach the inner panel to the exterior panel. Make sure the handle is located on the desired side.

13. Turn the upper decorative cover 180 degrees

and snap in the lower position. Turn the lower decorative cover 180 degrees and snap in the upper position

14. Replace the door gasket and ice scoop.

15. Remove the upper hinge plate by pushing in and

sliding to the outside and lower hinge plate by firmly pushing in and down as shown in the figure. ,QVWDOOWKHXSSHUDQGORZHUKLQJHSODWHVRQWKH opposite side.

17. Replace the door panel by

installing the top and bottom hinges with the 4 screws. Installation Instructions INSTALLATION INSTRUCTIONS ScrewsScrews

The ice machine is supplied without a conventional door covering, allowing the attachment of a door panel or a custom panel. NOTE:,IWKHGRRUVZLQJLVWREHFKDQJHGLWQHHGVWR be done BEFORE attaching the door panel. Door Panel Finished door panels with handles are available from GE Appliances for attachment to the ice machine. See Accessories on page 27. A custom panel of wood or other material not exceeding 15 lbs can be used and must follow these guidelines: ZLGWK´ KHLJKWEHWZHHQ´DQG´ WKLFNQHVV´WR´ For Custom Panel:

1. Place product in opening and level by adjusting

leveling legs as needed.

2. Measure how much if any the custom panel needs

to extend above the inner door panel to match any panels on either side. Note the clearance between the top of the panel and the countertop VKRXOGEHDWOHDVW´

3. Remove the door by removing the 4 hinge screws.

5. Lay panel on a surface and align the door on top

of the panel so that it located as measured in step

2. The sides of the panel should align with the

6. Mark locations of at least the 4 holes in the top

and bottom. Remove the door and measure and mark any remaining holes per the diagram. 'ULOOSLORWKROHVRQWKHEDFNRIWKHSDQHODW\RXU PDUNLQJV8VHDGULOOVWRSWRSUHYHQWGULOOLQJ through the panel. Cabinet opening´RUJUHDWHU clearanceToekick height´´´´´´Centerline´´ ´´୉´ TYP (10) Installation Instructions INSTALLATION INSTRUCTIONS16 49-1000640 Rev. 0 INSTALLING THE DOOR PANEL (Cont) ,IWKHGRRUVZLQJLVJRLQJWREHFKDQJHGSOHDVHFRPSOHWHSULRUWRLQVWDOOLQJWKHGRRUSDQHO6HHSDJH'HSHQGLQJRQWKHGRRUNLWEHLQJLQVWDOOHGWKHGRRUKDQGOHPD\QHHGWREHIOLSSHGLIWKHGRRUVZLQJLVEHLQJchanged. Please see instructions on page 18 on how to flip the door handle. Attaching the Door Panel 1. Remove the gasket from the inside of the door and retain for later use.,GHQWLI\WKHSU\WDEVRQWKHWRSDQGERWWRPdecorative door trims.3. Pry on each tab and pull down on the trim as shown until you can remove each of the trims.4. Remove any plastic protective covering from the stainless door panel5. Place the door panel onto the outside of the door and secure it with 6 machine screws. (Provided in 'RRU3DQHO.LW6. Snap the upper and lower trims back on the inner panel. 7. Re-install the door gasket. Installation Instructions INSTALLATION INSTRUCTIONS

449-1000640 Rev. 0 17 INSTALLING THE DOOR PANEL (Cont) 8. On free-standing locations, attach the side covers from the hardware packet over the hinge by peeling off the covering over the adhesive and placing it over the side of the hinge. Note:,IWKHXQLWLVEHLQJbuilt-in, a screw can be used to screw into the cabinet instead on installing the side covers.9. Also on free standing applications, attach the top hinge cover from hardware packet with the 2 screws provided.Side Cover Installation Instructions INSTALLATION INSTRUCTIONS WARNING Door Hinge Pinch Point Hazard,PSURSHULQVWDOODWLRQFDQOHDGWRDILQJHUSLQFKSRLQWKD]DUGQHDUWKHKLQJHZKHQRSHUDWLQJWKHGRRUFor installations that are not under a counter, follow the installation instructions. A protective guard is provided for limiting access to the door hinge.18 49-1000640 Rev. 0

Drain Installation NOTICE Restrictions in the drain system to the machine will cause water to back up into the ice storage bin and melt the ice. Gravity drain tubing must be vented, have no kinks, and slope to the building drain. Air gaps are typically required by local codes.1. Place the ice machine in front of the installation opening. Adjust leveling legs to the approximate height.,QVHUW GUDLQ WXEH WKURXJK WKH URXWLQJ KROH LQ WKHback panel.3. Remove the left side access panel for access to drain connection.NOTE: ,I WKH GUDLQ RSHQLQJ KDV EHHQ ORFDWHG LQ WKHfloor under the base pan according to the pre install specifications, follow steps 4 through 6 to drain the XQLW WKURXJK WKH EDVH ,I QRW SURFHHG WR VWHS Installation Instructions

HANDLE REVERSING INSTRUCTIONS

1. Remove the allen wrench from the panel installation screw kit envelope2. Loosen the set screw using the allen wrench. Remove the handle and flip it around so the logo is facing the other way. 3. Place the handle caps over the fasteners of the door. Take care to support the handle so it doesn’t fall and scratch the appliance finish. Make sure both handle caps are resting on the face of the door.4. Lock one end of the handle into position by tightening the set screw in the handle cap with the DOOHQ ZUHQFK SURYLGHG '2 127 RYHUWLJKWHQ5. Keep supporting the handle as you lock the other end of the handle into position by tightening the set VFUHZ LQ WKH KDQGOH FDS '2 127 RYHUWLJKWHQLOOSENset screwset screwfastenerhandle capset screwset screw INSTALLATION INSTRUCTIONS49-1000640 Rev. 0 19 INSTALLATION INSTRUCTIONS PLUMBING - GRAVITY DRAIN (cont) 4. Remove the clamp and rotate the barbed elbow so that it is pointing down toward the hole (see figure a below). Re-secure the barbed elbow with the clamp. Take off the plastic cover in the base pan below the drain hose. &XWDQSLHFHRI2'[2'W\JRQ(clear plastic) tubing. Slide one end of the tube onto the clamp, Leave the other end of the tube lying on the floor of the base pan until the unit is positioned over the floor drain.6. Route the drain tube. Either a) insert the drain tube through the base pan into the floor drain or b)) route the drain tube through the hole in the lower back panel and connect to barbed elbow and secure with clamp.IMPORTANT: Make sure to use tubing that cannot be kinked.7. Reinstall any panels removed to connect the drain. Water Supply The recommended water supply line is part number WX08X10006G. and is available at *($SSOLDQFHSDUWVFRPRUE\FDOOLQJ,QCanada visit GEAppliances.ca or call 800.561.3344.,QVWDOODQHDVLO\DFFHVVLEOHVKXWRIIYDOYHEHWZHHQthe supply and the unit. This shut- off valve should not be installed behind the unit.The water connection is at the back of the cabinet. When built in: Coil enough tubing behind the machine so it can be pushed into the cavity without kinking the tubing.

The toe kick can be adjusted to help align with your cabinets. The toe kick comes installed in the inward position. To move the toe kick to the outward position:1. Loosen the screws on both sides as shown to remove the metal toe kick.2. Loosen the 2 long screws in front and remove the plastic frame.,QVHUWWKHEXVKLQJVSURYLGHGLQWKHOLWHUDWXUHEDJonto the 2 posts and 2 attachment screws on the rear of the frame as shown.4. Re-install the plastic frame using the 2 long screws.5. Re-install the metal toe kick using the 2 screws in the side. The toe kick can be adjusted up and down to your desired position.Connect water supply here. Installation Instructions20 49-1000640 Rev. 0 GSWF Water Filter Water Filter Cartridge The water filter cartridge is located at the bottom of the icemaker behind the water filter access door. When to Replace the Filter Cartridge

³5HSODFH)LOWHU´,QGLFDWRUZLOOFRPHRQZKHQLWLVWLPHWRRUGHUDILOWHU7KLVZLOORFFXUDIWHUDSSUR[LPDWHO\PRQWKV

or earlier after periods of heavy icemaking. To order additional filter cartridges, visit our website at gewaterfilters. com or call GE Appliances Parts and Accessories, 877.959.8688 and order filter GSWF.

³5HSODFH)LOWHU´,QGLFDWRUZLOOIODVKZKHQLWLVWLPHWRUHSODFHWKHILOWHU7KLVZLOORFFXUDIWHUDSSUR[LPDWHO\PRQWKV

or earlier after periods of heavy icemaking. Replacing the Filter

1. Make sure power is turned off (making sure ice light is not on).

2. Open water filter access door by pulling on the top of the door

3. Gently grasp the filter and slowly turn it to the left about a ¼

turn until you can pull it out. A small amount of water may drip out of the filter. Filter Bypass Plug ,IDUHSODFHPHQWILOWHUFDUWULGJHLVQRWDYDLODEOHDE\SDVVSOXJPXVWEHXVHGLQRUGHUIRUWKHLFHPDNHUWRIXQFWLRQ 7RREWDLQDE\SDVVSOXJFDOO*(&$5(6DQGUHTXHVW:5;ILOWHUE\SDVVSOXJ,Q&DQDGDFDOO

800.561.3344. The left side panel will need to be removed to install a filter bypass plug. Be sure to unplug the

icemaker before trying to install a bypass plug. Installing the Filter

1. Open water filter access door by pulling on the top of the door until it flips open

automatically adjust itself into position. The filter will move about ¼ turn or 90 degrees when in the correct position.

4. Gently close the filter access door until it snaps into place

3UHVVDQGKROGWKH)LOWHU5HVHWEXWWRQIRUVHFRQGVWRUHVHWWKHILOWHUWLPHUFRXQWHU

,I\RXKDYHTXHVWLRQVRUWRRUGHUDGGLWLRQDOILOWHUFDUWULGJHVYLVLWRXUZHEVLWHDWJHZDWHUILOWHUVFRPRUFDOO*( Appliances Parts and Accessories, 877.959.8688. Water filter Kick Plate CARE AND CLEANING49-1000640 Rev. 0 21

Cleaning the Outside The stainless steel door and door handle can be cleaned with a commercially available stainless steel cleaner. Cleaners with oxalic acid such as Bar Keepers Friend Soft Cleanser™ will remove surface rust, tarnish and small blemishes. 8VHRQO\DOLTXLGFOHDQVHUIUHHRIJULWDQGUXELQWKHGLUHFWLRQRIWKHEUXVKOLQHVZLWKDGDPSVRIWVSRQJH'Rnot use appliance wax or polish on the stainless steel. Cleaning the Condenser The condenser has fins and tubes that can become clogged with dirt and lint.To clean:1.8QSOXJWKHLFHPDNHU2. Remove the kickplate by removing the 2 screws in the sides of the metal grill, then 2 additional screws from the front of the kickplate. Pull kickplate forward to remove. To access top of condenser, remove door by removing the hinges from the cabinet. Open the water filter access door and remove 2 screws in the filter cover. Remove hinge cover plate on opposite side of hinge by firmly pressing in and sliding down. Pull filter cover forward to remove.3. Vacuum the surface to remove all dust and lint. NOTICE Do not dent the fins.4. Re-install the filter cover, hinge cover plate, kick plate and door. Care And Cleaning Screws

WARNING Electrical Shock HazardTo eliminate the risk of electric shock or injury, you must first unplug the icemaker before proceeding. Failure to follow these instructions can result in electrical shock or injury.22 49-1000640 Rev. 0

Cleaning the ice machine involves adding a cleaner to the ice machine. You should use rubber gloves when using the scale remover. To order cleaner, go to GEApplianceParts.com or call 877-959-8688. Order part number WX01X40745.

1. Pour 3 ounces of cleaner into the squirt bottle.

batch of ice is released. This could take up to 30 minutes.

3. Scoop out and discard all of the ice in the ice bin.

2QFHWKH,FHPDNLQJOLJKWWXUQVRIISUHVVDQGKROG Clean button for 3 seconds to begin cleaning function. The Time to Clean light will start to flash.

5. After the Time to Clean light starts flashing, add the

3 ounces of cleaner from the squirt bottle as shown.

6. The icemaker will continue the cleaning process.

This can take up to one hour. When the process is complete, the Time to Clean light will turn off.

7. Pour approximately 1/2 gallon of hot (95-115°F)

water into the bin to flush out the bin.

8. Mix one ounce of cleaner with one quart of water

and clean the ice bin, interior door and gasket surfaces.

6DQLWL]HWKHELQDQGGUDLQE\SRXULQJDPL[WXUHRI

ounce of household bleach with 2 gallons of water into the bin.

10. Rinse the bin again with hot water.

11. Push and hold the Power button for 3 seconds to

restart ice making. The ice scoop should also be washed regularly. Care And Cleaning Winterizing

:LWKWKHLFHPDNHULQWKH0DNLQJ,FHPRGHRSHQ

the door and push the Power button to turn the ice

PDFKLQHRII7KH0DNLQJ,FHOLJKWZLOOIODVKXQWLO

the current icemaking cycle is completed (up to 20 minutes) and the icemaker tank will automatically drain. (Make sure to turn off the icemaker in this way. ,IWKHLFHPDNHULVXQSOXJJHGZLWKRXWILUVWWXUQLQJLWRII the water in the tank will not drain.)

2. Turn off the water supply.

3. Models with a drain pump installed should have about

JDOORQRI59DQWLIUHH]HSURS\OHQHJO\FROSRXUHG

into the ice storage bin drain.

NOTE: $XWRPRWLYHDQWLIUHH]HPXVW127EHXVHG

4. Turn off and unplug the machine.

NOTE: When placing the icemaker back in service DIWHUZLQWHUL]LQJLWLVUHFRPPHQGHGWRFRPSOHWHWKH cleaning process on page 21. Vacation

,I\RXSODQRQEHLQJDZD\IRUDQH[WHQGHGSHULRGRI

time, it is recommended that you turn off icemaking. 3UHVVDQGDQGKROG3RZHUIRUVHFRQGV ,ILFHPDNHULVPDNLQJLFHZKHQWXUQHGRIIWKH0DNLQJ ,FHLQGLFDWRUZLOOIODVKIRUXSWRPLQXWHVWRDOORZ the icemaker to complete the icemaking process prior to turning off. The icemaker will also drain any water in the tank every time it is turned off. CARE AND CLEANING49-1000640 Rev. 0 23 Problem Possible Causes What to Do Low ice rate Restricted drain or standing water in the bin Clean the air cooled condenser fins. Clean the ice making system. Check the drain line for kinks Room temperature may be high ,FHPDNHURSHUDWHVEHVWLQWHPSHUD- tures between 60 and 90 degrees F. Ice cubes are incompletely formed Scale on the ice making system Clean the ice making system No ice Power is OFF 3UHVVDQGKROGWKH3RZHUEXWWRQ VHFRQGVWRWXUQLFHPDNLQJRQ0DN- LQJ,FHOLJKWVKRXOGWXUQRQ Electric breaker has been tripped )OLSWKHHOHFWULFEUHDNHUEDFNRQ,IWKH breaker trips again, call service..

alternately) Check to make sure water supply is on or supply lines are not kinked. Water filter may need to be replaced. Component or sensor problem. 'LႇHUHQWOLJKWVRQFRQWUROSDQHOZLOO EHÀDVKLQJ Call service. Time to Clean light is on Clean the ice making system following directions in the Care and Cleaning section. Water backs up into ice bin 'UDLQWXELQJLVNLQNHG 8VHGUDLQWXELQJWKDWGRHVQRWNLQN Noise 7KHLFHPDFKLQHLVGHVLJQHGIRUTXLHWRSHUDWLRQEXWZLOOPDNHVRPHQRLVHGXULQJWKHLFHPDNLQJF\FOH'XULQJD

IUHH]LQJF\FOHLWLVQRUPDOWRKHDUWKHIDQPRYLQJDLUDQGWKHZDWHUSXPSFLUFXODWLQJZDWHU,FHKLWWLQJWKHELQRULFH

in the bin can be heard during harvest. Troubleshooting Tips... Before you call for service

6DYHWLPHDQGPRQH\5HYLHZWKHFKDUWVRQWKHIROORZLQJSDJHVILUVWDQG\RXPD\QRWQHHGWRFDOOIRUVHUYLFH

TROUBLE SHOOTING TIPS24 49-1000640 Rev. 0 Notes49-1000640 Rev. 0 25 Notes26 49-1000640 Rev. 0 Ŷ Service trips to your home to teach you how to use the product. Ŷ,PSURSHULQVWDOODWLRQGHOLYHU\RUPDLQWHQDQFH Ŷ Failure of the product if it is abused, misused, or used for other than the intended purpose or used commercially. Ŷ Replacement of house fuses or resetting of circuit breakers. Ŷ'DPDJHFDXVHGDIWHUGHOLYHU\ Ŷ Replacement of the light bulbs, if included. Ŷ'DPDJHWRWKHSURGXFWFDXVHGE\DFFLGHQWILUHIORRGV or acts of God. Ŷ,QFLGHQWDORUFRQVHTXHQWLDOGDPDJHFDXVHGE\ possible defects with this appliance. Ŷ Product not accessible to provide required service. What GE Appliances Will Not Cover: For the Period of: GE Appliances Will Replace One Year From the date of the original purchase Any part of the ice machine which fails due to a defect in materials or workmanship. 'XULQJWKH limited one-year warranty, GE Appliances will also provide, free of charge, all labor and related service to replace the defective part. Five Years From the date of the original purchase Any part of the sealed refrigeration system (the compressor, condenser, evaporator and all connecting tubing) which fails due to a defect in materials or workmanship. 'XULQJWKH limited five-year sealed refrigerating system warranty, GE Appliances will also provide, free of charge, all labor and related service to replace the defective part in the sealed refrigerating system. Staple your receipt here. Proof of the original purchase date is needed to obtain service under the warranty. GEAppliances.com $OOZDUUDQW\VHUYLFHLVSURYLGHGE\RXU)DFWRU\6HUYLFH&HQWHUVRUDQDXWKRUL]HG&XVWRPHU&DUH

technician. To schedule service online, visit us at geappliances.com/service, or call GE Appliances at 800.GE.CARES (800.432.2737). Please

KDYH\RXUVHULDOQXPEHUDQG\RXUPRGHOQXPEHUDYDLODEOHZKHQFDOOLQJIRUVHUYLFH,Q&DQDGDYLVLW

GEAppliances.ca/en/support/service-request or call 800.561.3344 GE Appliances Ice Machine Limited Warranty

EXCLUSION OF IMPLIED WARRANTIES

Your sole and exclusive remedy is product repair as provided in this Limited Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a particular purpose, are limited to one year or the shortest period allowed by law. For US Customers: This limited warranty is extended to the original purchaser and any succeeding owner for products

SXUFKDVHGIRUKRPHXVHZLWKLQWKH86$,IWKHSURGXFWLVORFDWHGLQDQDUHDZKHUHVHUYLFHE\D*($SSOLDQFHV$XWKRUL]HG

Servicer is not available, you may be responsible for a trip charge or you may be required to bring the product to an $XWKRUL]HG*($SSOLDQFHV6HUYLFHORFDWLRQIRUVHUYLFH,Q$ODVNDWKHOLPLWHGZDUUDQW\H[FOXGHVWKHFRVWRIVKLSSLQJRU service calls to your home. Some states do not allow the exclusion or limitation of incidental or consequential damages. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state. To know what your legal rights are, consult your local or state consumer affairs office or your state’s Attorney General. Warrantor: GE Appliances, a Haier company Louisville, KY 40225 For Customers in Canada: This limited warranty is extended to the original purchaser and any succeeding owner

IRUSURGXFWVSXUFKDVHGLQ&DQDGDIRUKRPHXVHZLWKLQ&DQDGD,QKRPHZDUUDQWVHUYLFHZLOOEHSURYLGHGLQDUHDV

where it is available and deemed reasonable by Mabe to provide. Warrantor Canada: MC Commercial, Inc., Burlington, Ontario, L7R 5B6 LIMITED WARRANTY49-1000640 Rev. 0 27 ACCESSORIES Accessories Looking For Something More? Finished stainless steel door panels with handles are available from GE Appliances for attachment to the ice machine.The panel kits are: =.815666WDLQOHVVVWHHOGRRUZLWKRXWKDQGOH The following Monogram handles are available for purchase separately:

• ZXGP1H1CPSS – Brushed stainless Minimalist handle

kits. To order, go to GEApplianceParts.com or call

877-959-8688. ,Q&DQDGDYLVLW

GEAppliances.ca/en/ products/parts-filter-accessories or call 800.661.1616. Drain Conversion: A gravity drain model can be converted to a drain pump model by installing a drain pump kit. The drain pump kit consists of a drain pump, wiring harness and associated tubing. The part number

GEAppliances.ca/en/products/parts-filter-accessories or call 800.661.1616.28 49-1000640 Rev. 0 Consumer Support CONSUMER SUPPORT GE Appliances Website Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day, any day

communication and prompt service under the terms of your warranty, should the need arise. You may also mail in the pre-printed registration card included in the packing material. ,QWKH86GEAppliances.com/register ,Q&DQDGDProdsupport.mabe.ca/crm/Products/ProductRegistration.aspx Schedule Service Expert GE Appliances repair service is only one step away from your door. Get on-line and schedule your service at \RXUFRQYHQLHQFHDQ\GD\RIWKH\HDU,QWKH86GEAppliances.com/service or call 800.432.2737 during normal business hours. ,Q&DQDGDGEAppliances.ca/en/support/service-request or call 800.561.3344 Extended Warranties Purchase a GE Appliances extended warranty and learn about special discounts that are available while your warranty is still in effect. You can purchase it on-line anytime. GE Appliances Services will still be there after your ZDUUDQW\H[SLUHV,QWKH86GEAppliances.com/extended-warranty or call 800.626.2224 during normal business hours. ,Q&DQDGDGEAppliances.ca/en/support/purchase-extended-warranty or call 866.277.9842. Parts and Accessories ,QGLYLGXDOVTXDOLILHGWRVHUYLFHWKHLURZQDSSOLDQFHVFDQKDYHSDUWVRUDFFHVVRULHVVHQWGLUHFWO\WRWKHLUKRPHV

9,6$0DVWHU&DUGDQG'LVFRYHUFDUGVDUHDFFHSWHG2UGHURQOLQHWRGD\KRXUVHYHU\GD\

,QWKH86GEApplianceparts.com or by phone at 877.959.8688 during normal business hours. Instructions contained in this manual cover procedures to be performed by any user. Other servicing generally should be referred to qualified service personnel. Caution must be exercised, since improper servicing may cause unsafe operation. Customers in Canada should consult the yellow pages for the nearest Mabe service center, visit our website at GEAppliances.ca/en/products/parts-filters-accessories or call 800.661.1616. Contact Us

49-1000640 Rev. 0 12-21 GEA UCC15NP

3 7/8" 20 3/8" FLOOR DRAIN ACCESS HOLE Water inlet:1/4"49-1000640 Rev. 0

EMPLACEMENT DU COUP-DE-PIED

49-1000640 Rev. 0 Notes49-1000640 Rev. 0

Notes26 49-1000640 Rev. 0