SDR20JBE3 - Water pump Maxxmee - Free user manual and instructions
Find the device manual for free SDR20JBE3 Maxxmee in PDF.
| Product Type | Instantaneous water heater |
| Brand | Maxxmee |
| Model | SDR20JBE3 |
| Rated Voltage | 220-240 V ~ 50/60 Hz |
| Rated Power | 3000 - 3600 W |
| Protection Class | I |
| Protection Rating | IPX4 |
| Service Pressure | 0.04 - 0.4 MPa (1.4 - 6 l/min) |
| Maximum Water Temperature | 60 °C (at 10 °C inlet) |
| Electrical Connection | Plug with 16 A fuse |
| Body Material | Stainless steel |
| Main Functions | Instantaneous heating, flow and temperature regulation, LED digital display |
| Package Contents | Appliance body, 1/2" and 3/4" adapters, universal adapter, metal clamp, sealing rings, cable ties, user guide |
| Care and Cleaning | Clean with damp cloth; regular descaling of the aerator |
| Safety | Resettable overheat fuse, IPX4 protection, automatic shutdown in case of fault |
| Intended Use | Domestic use, connection to cold water only, vertical installation |
Frequently Asked Questions - SDR20JBE3 Maxxmee
User questions about SDR20JBE3 Maxxmee
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Water pump in PDF format for free! Find your manual SDR20JBE3 - Maxxmee and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. SDR20JBE3 by Maxxmee.
USER MANUAL SDR20JBE3 Maxxmee
5 Universaladapter, 1 x
6 Metallschelle, 1 x
7 Kleiner Dichtungsring (des 12 "-Adapters), 1 x
Cleaning and Storage 14
Reactivating the Device 14
Troubleshooting 14
Disposal 15
Technical Data 15
ITEMS SUPPLIED
(Picture A)
1 Main device with connecting cable, 1 x
2 12 " adapter, 1 x
3 34 " adapter (e.g. for quick coupling to the water inlet), 1 x
4 Cable ties, 3 x
5 Universal adapter, 1 x
6 Metal clamp, 1 x
7 Small sealing ring (of the 12 " adapter), 1 x
8 Medium sealing ring (for the water inlet), 1 x
9 Large sealing ring (of the 34 " adapter), 1 x
Not shown:
- 3/4'' plastic adapter (e.g. for quick coupling to the water outlet), 1 x
- Assembly and operating instructions, 1x
Check the items supplied for completeness and the components for transport damage. If you find any damage, do not use the device but contact our customer service department.
Remove any possible films, stickers or transport protection from the device.
Never remove the rating plate and any possible warnings!
AT A GLANCE
(Picture B)
10 Water inlet
11 Water regulator (On / Off and temperature)
12 Position marker
13 Flow regulator (detachable)
14 Water outlet
15 Display
Dear Customer,
We are delighted that you have chosen the MAXXMEE stainless steel continuous-flow water heater. It can be installed quickly, easily and effortlessly in almost any place where there is a water and power supply. Screw it on, plug in, and that's it! Thanks to the integrated, powerful heating coil, the water is instantly hot – without delay and without a water tank! You can also read off the precise temperature at any time on the digital LED display. You can now finally have hot water wherever you have always needed it: in the garden, in your workshop, on the patio, in a caravan etc.
If you have any questions about the device and about spare parts/accessories, contact the customer service department via our website: www.dspro.de/kundenservice
We hope you have a lot of fun with your MAXXMEE stainless steel continuous-flow water heater.
Information About the Assembly and Operating Instructions
Before using the device for the first time, please read through these assembly and operating instructions carefully and keep them for future reference and other users. They form an integral part of the device. The manufacturer and importer do not accept any liability if the information in these assembly and operating instructions is not complied with.
SYMBOLS
Danger symbols: These symbols indicate possible dangers. Read the associated safety notices carefully and follow them.
Supplementary information
Read the assembly and operating instructions before use!
AC voltage
Suitable for use with food.
SIGNAL WORDS
Signal words indicate hazards if the associated notices are not followed.
DANGER – high risk, results in serious injury or death
WARNING – medium risk, may result in serious injury or death
NOTICE – may result in risk of damage to material
INTENDED USE
■ The device is intended to be used to shut off water, convey water, regulate the water flow and heat water.
It must be ensured that the specifications in relation to the power connection and water pressure (see the "Technical Data" chapter) are followed.
■ The device is for personal use only and is not intended for commercial applications.
■ Use the device only for the specified purpose and as described in the assembly and operating instructions. Any other use is deemed to be improper.
■ The warranty does not cover faults caused by incorrect handling, damage or attempted repairs. The same applies to normal wear and tear.
SAFETY NOTICES
This device may be used by children aged 3 and over and by people with reduced physical, sensory or mental abilities or people with a lack of experience and/or knowledge if they are supervised or have received instruction on how to use the device safely and have understood the dangers resulting from failure to comply with the relevant safety precautions.
■ Children must not play with the device.
■ Cleaning and user maintenance must not be carried out by children without supervision.
■ The device must always be disconnected from the mains power before cleaning / maintenance and when not in use for a prolonged period.
- Do not make any modifications to the device. Do not replace the connecting cable yourself. If the device, the connecting cable or the accessories are damaged, they must be replaced or repaired by the manufacturer, customer service department or an authorised distributor in order to avoid any hazards.
■ WARNING: Do not switch on the device if it is possible that the water inside the water heater is frozen.
■ The outlet must not be connected to valves and fittings other than those specified.
■ The water inlet of this device must not be connected to water flowing in from other water heating systems.
DANGER – Danger of Electric Shock
- Keep children and animals away from the connecting cable when it is connected to the mains power.
- Do not use the device if water emerges from a place other than the water outlet.
■ Never immerse the device and the connecting cable in water or other liquids and ensure that they cannot fall into water or become wet.
■ Never touch the device and the connecting cable with wet hands when the device is connected to the mains power.
If the device falls into water while it is connected to the mains power, pull the mains plug out of the plug socket immediately. Only after this should you retrieve the device from the water.
■ Store the device only in closed rooms.
■ Do not store the device in rooms with high humidity.
WARNING – Danger of Injury
- Keep children and animals away from the packaging material. There is a danger of suffocation.
■ Make sure that the connecting cable is always kept out of the reach of small children and animals. There is a danger of strangulation.
NOTICE – Risk of Damage to Material and Property
■ Use only original accessories from the manufacturer in order to guarantee that there is no interference that may prevent the device from working and to avoid possible damage.
■ Switch off the device and pull the mains plug out of the plug socket if an error occurs during operation or before a thunderstorm.
■ Always pull the mains plug and never the mains cable to disconnect the device from the mains power.
■ Do not place heavy objects on the device or the connecting cable.
■ Make sure that the connecting cable is not squashed, bent or laid over sharp edges and does not come into contact with hot surfaces. Do not cover the connecting cable, with a cloth for example.
■ Protect the device from fire, extreme temperatures and impacts.
■ Regularly descale the flow regulator.
ASSEMBLY
Please Note!
■ Do not install in places where there is a risk of frost!
■ The device must only be connected to a cold water pipe. If there is both a cold and a hot water connection, only the cold water connection may be used. If you have any questions or are uncertain, consult a plumbing expert.
■ This device must be installed upright.
■ First connect the device to the water pipe and only after this to the power cable.
■ Always disconnect it from the power cable first after use.
■ Only connect the device to a plug socket with a 16 A fuse that is properly installed. The mains voltage must match the technical data of the device.
The plug socket must also be readily accessible after connection so that the
connection to the mains can quickly be isolated.
- Do not connect the device along with other consumers with a high wattage to a circuit in order to prevent overloading and a possible short circuit (fire). Make sure that the circuit is designed to handle the power of the device.
■ Do not use any multiple sockets, extension cables more than 3 m long or cable extension reels. - The water pressure of the water supply pipe must be within the limits which are specified in the “Technical Data” chapter.
- Check the device, the connecting cable and all accessories for damage prior to installation. Use the device only if all components are undamaged and in working order.
We recommend connecting the water inlet (10) of the device directly, or via a quick coupling, to a tap, and not to a hose. To ensure it works perfectly, you should avoid using a power cable or water supply pipe which is too long.
- Fit the main device (1) on the water supply connection (preferably a tap). To do this, insert the medium sealing ring (8) into the water inlet (10) and ...
a) ... screw this onto the water supply connection,
b) ... with a 34 " thread (e.g. a quick coupling) insert the large sealing ring (9) into the 34 " adapter (3) and screw this in between (Picture C),
c) ... with a 12 " thread insert the small sealing ring (7) into the 12 " adapter (2) and screw this in between (Picture C),
d) ... with other water supply connections, in addition to the 12 " adapt-
er (2) with the sealing ring, use the universal adapter (5) and the metal clamp (6) (Picture D). Screw the universal adapter into the 12 " adapter. Plug the other end onto the water supply connection and fix it in place with the metal clamp (6) by twisting it tighter.
- If a quick coupling is to be fitted on the water outlet (14), unscrew the flow regulator (13) and screw in the 34 " plastic adapter. Screw a standard quick coupling onto it. Otherwise skip this step.
- Open the water supply.
- Turn the water regulator (11) of the device to water flow (turn it downwards until you hear a click) and check all connections for any leaks. Fix any leaks.
- Only if there are no leaks should you plug the mains plug into the plug socket.
USE
Picture E shows the possible positions of the water regulator (11) and the corresponding settings:
- If the water regulator is in the middle position, the water flow is switched off.
- When the water regulator is turned downwards, the flow of cold water increases.
- When it is turned upwards, the flow of hot water increases. The water temperature drops as the amount of water flowing in the hot water range increases.
When the device is operated in the hot water range, the display shows the current water temperature.
Power is only consumed when producing hot water. It is therefore not necessary to pull out the mains plug to save electricity.
CLEANING AND STORAGE
Please Note!
■ Do not use any sharp or abrasive cleaning agents or cleaning pads to clean the device. These may damage the surfaces.
- Wipe any dirt off the device with a damp cloth.
- Store the device in a cool, dry place that is out of the reach of children and animals.
If the flow of water becomes weaker or irregular, the flow regulator (13) should be cleaned:
- Unscrew the flow regulator and rinse it out.
- Remove possible limescale deposits with a standard descaling agent.
- Do not forget the sealing ring when reassembling it!
REACTIVATING THE DEVICE
Overheating may cause the fuse of the device to be triggered. To put the device back into operation, open up the water regulator (11) by applying a little force and press the reset button (Picture F).
TROUBLESHOOTING
If the device does not work properly, check whether you are able to rectify the problem yourself. If the problem cannot be solved with the steps below, contact the customer service department.
Do not attempt to repair an electrical device yourself!
The flow of water has become weaker.
The flow regulator (13) is dirty / furred up.
▶ Clean it in the manner described in the "Cleaning and Storage" chapter.
The water does not get hot and the display is not switched on.
The mains plug is not inserted in the plug socket correctly.
▶ Correct the fit of the mains plug.
The fuse of the device has been triggered due to overloading.
▶ Put the device back into operation in the manner described in the "Reactivating the Device" chapter.
The plug socket is defective.
▶ Try another plug socket.
There is no mains voltage.
▶ Check the fuse of the electrical distributor (fuse box).
The water is lukewarm.
The greater the quantity of hot water, the cooler the water becomes.
▶ Reduce the flow of water.
The water is too hot.
The water inlet (10) is blocked.
▶ Unscrew the device from the water supply connection and remove the blockage.
The water pressure of the supply pipe is too low.
The requirements for the water pressure are listed in the "Technical Data" chapter. These requirements should be met to ensure the device works in the optimum way.
The fuse in the fuse box has been triggered.
Too many devices connected in one circuit.
▶ Reduce the number of connected devices.
The circuit is not designed to handle the power of the device.
Connect it to another circuit. The requirements are listed in the "Technical Data" chapter.
DISPOSAL
Dispose of the packaging material in an environmentally friendly manner so that it can be recycled.
This device is governed by the European Directive 2012/19/EU on waste electrical and electronic equipment (WEEE). Do not dispose of this device as normal domestic waste, but rather in an environmentally friendly manner via an officially approved waste disposal company.
TECHNICAL DATA
Article number: 04900
Model number: SDR-20JBE-3
Rated voltage: 220 – 240V \~ 50/60Hz
Power: 3000 - 3600W
Protection class: I
Type of protection: IPX4
Operating pressure: 0.04 - 0.4 MPa (1.4 - 6 l/min)
Rated pressure: 0 MPa
Power connection: Plug socket with a 16 A fuse
Water temperature: up to 60^ C at the water inlet with a temperature of approx. 10^ C
ID of assembly and
operating instructions: Z 04900 M DS V2.1 0321 md
All rights reserved.
EN
MAXXMEE
SOMMAIRE
Composition 17
Aperçu général 17
Symboles 18
5 Universele adapter, 1 x
6 Metalen klem, 1 x
7 Kleine afdichtring (van de 12 "-adapter), 1 x
WAARSCHUWING – Verwon- dingsgevaar
APPARAAT REACTIVEREN
De contactdoos is defect.
▶ Reduceer de waterstroom.
De watertoevoer (10) is verstopt.
