SLCATL320 - Pressure washer SereneLife - Free user manual and instructions

USER MANUAL SLCATL320 SereneLife

IMPORTANT Before using our product, please familiarise yourself with the components.

• High density polyethylene construction.

• Completely self contained.

• No external connections required.

• Secure clamps and latches.

• All parts are easily replaced by end users.

• 20L waste holding tank.

• 10L fresh water tank.

• Easy to carry and clean.

• Adult sized seat and lid are well constructed.

• Always ushes with clean water, no water is re-circulated.

• Completely self-contained. No external water or power connections.

• Fresh water capacity provides up to 50 ushes.

• Attractive matt nish conceals marks, and allows scrubbing without damage.

• Double sealed drain valve protects against leakage and odour.

• Heavy duty, corrosion resistant side latches lock tanks together.

• Detached waste holding tank is easy to empty.

• Both tanks are single piece construction with no leaking seams.

• Waste level indicator tells you when to empty.

• No splash rotating pour spout.

• Innovative T-type 3 way ush nozzle ensures a full bowl coverage.

• Upgraded piston pump works more eciently.

• Selectable bracket can increase the height. Description Seat Cover Seat Hinge Pin Piston Pump Assembly Cap, Fresh Water Holding Tank Fresh Water Holding Tank Assembly Latch Assembly Sealed C Ring Slide Valve Assembly Sealed D Ring Cap. Rotating Pour Spout. Rotating Pour Spout Waste Holding Tank 20L NO.

1. Set the SLCATL320 on its front side so that the cap

on the waste holding tank is in a vertical position. Remove the cap and add deodoriser following instructions on the deodoriser container. Tighten the cap rmly.

2. Set the toilet in an upright position and removethe

cap located on the right rear side of the fresh water tank. Fill with fresh water up to the top of the fresh water tank. Then tighten the cap rmly.

EMPTYING WASTE HOLDING TANK

The SLCATL320 has a 20L waste holding tank. It should be emptied when contents reaches approximately 2cm below Slide Valve, or the level indicator turns to red.

1. Separate tanks by pulling outward on side latches,

then lifting upward on water tank. Make sure slide valve is completely closed.

2. Use moulded handle to carry the holding tank.

tank. Add fresh water, close cap and shake tank to rinse.

5. Remove cap and pour rinse water out of the tank.

Close cap rmly and assemble fresh water tank and waste holding tank together again.

6. Prepare for continued use by following steps 1 and

2 of “Preparing for Use”. SAFETY INSTRUCTION

1. Handle with care.

2. Avoid exposure to direct sunlight for extended

4. To avoid injury DO NOT lean against lid when

5. Ensure waste tank is cleaned regularly.

6. Suitable for use with any brand of portable toilet

chemicals and deodorisers. MAINTENANCE

1. Lubricate Slide Valve seals periodically with silicone

spray or white grease lubricant.

2. The Slide Valve may be removed for cleaning or

inspection by simply unscrewing in a counter clockwise direction.

3. Clean exterior of toilet with a mild, non-abrasive

bathroom cleaner. STORAGE To store our Portable Toilet when not in use:

1. Empty the top tank and waste holding tank.

2. Make sure all water is cleared from the bellows

pump by depressing pump several times.

3. Stored away from direct sunlight.

Note: A small amount of water may remain in the top tank but will be harmless during storage. CAUTION: A. Do not add deodoriser to top fresh water tank. B. Avoid adding holding tank deodoriser through bowl. Use cap on the bottom rear tank if possible. Rinse o any spilled or splashed deodoriser immediately. C. Atmospheric pressure and temperaturechanges may cause pressure build up in lowerholding tank. Caution should be used when rst opening the slide valve.

1. Depress Flush Pump to add water to the bowl.

2. After use, pull Slide Valve handle out.

3. Depress Flush Pump again to rinse the bowl.

4. Close Slide Valve by pushing in fully.