XTREME MX1000R - Blender Waring Pro - Free user manual and instructions

Product Type	Professional Blender
Brand	Waring Pro
Model	XTREME MX1000R
Bowl Capacity	1.9 L (64 oz)
Bowl Material	Polycarbonate
Number of Speeds	2 (LOW and HI) + Pulse function
Motor Power	3 HP (horsepower)
Voltage / Frequency	120 V ~ 60 Hz
Rated Current	12 A
Cord Length	1.85 m
Height	48 cm
Weight	6.8 kg
Control Type	Rotary switch (on/off/pulse)
Pulse Function	Yes, momentary high-speed action
Hot Liquids	Maximum 250 ml, remove the measuring cap
Duty Cycle	1 minute on / 3 minutes off
Certifications	cETLus, NSF
Cleaning	Manual with detergent and disinfectant solutions
Repairability	Repairs by an authorized after-sales service
Power Supply	Grounded outlet required (120 V)

Frequently Asked Questions - XTREME MX1000R Waring Pro

How to use the pulse function?

To use the pulse function, push the switch to the PULSE position and hold it down. The blender runs at high speed as long as you hold the switch. Release to stop.

Can I blend hot liquids?

Yes, but with caution: only blend a maximum of 250 ml of hot ingredients (temperature above 38°C). Remove the measuring cap to allow steam to escape, start at low speed and increase gradually. Do not lean over the blender while it is running.

How to clean the blender?

Unplug the appliance. Remove the bowl and lid. Rinse, then fill the bowl a quarter full with a cleaning solution (non-foaming detergent). Close the lid without the cap and run at high speed for 2 minutes. Empty, rinse with clear water and repeat the process with a disinfecting solution. Air dry. Clean the base with a damp sponge, without immersion.

What to do if the blender does not start?

Check that the bowl is properly installed on the base and the lid is firmly closed. Make sure the appliance is plugged into a functional grounded outlet (120 V). If the problem persists, contact an authorized after-sales service.

Can I blend frozen ingredients?

Yes, use the pulse function or high speed (HI) to crush ice or blend frozen fruits. Do not fill above the MAX line and proceed with short bursts.

How to change the blades?

The blades are not user replaceable. For any intervention, contact an authorized after-sales service. The blades are very sharp: handle the bowl with care during cleaning.

Is the bowl dishwasher safe?

No, the polycarbonate bowl and lid must be washed by hand according to the cleaning instructions. Do not use a dishwasher as high temperatures and aggressive detergents could damage the parts.

What is the maximum liquid capacity?

The total bowl capacity is 1.9 L (64 oz). Never fill beyond the MAX line to avoid overflow. For hot liquids, limit to 250 ml.

Can I use the blender without the lid?

No, the lid must always be in place during operation to prevent splashing and injury. Only remove the measuring cap for hot liquids or to add ingredients while blending.

How to disinfect the blender?

After cleaning, fill the bowl with a disinfecting solution (for example 1 tablespoon of bleach per 4 L of cold water). Run at high speed for 2 minutes, empty, then run dry for 2 seconds to dry the blades. Do not rinse after disinfection: let air dry.

USER MANUAL XTREME MX1000R Waring Pro

For your safety and continued enjoyment of this product, always read the instruction book carefully before using.

IMPORTANT UNPACKING INSTRUCTIONS

1. Place the box containing your Waring Pro® blender on a flat sturdy surface before unpacking.
2. Open corrugated flaps.
3. Remove instruction book and any printed materials from top of box.
4. Pull up corrugation and remove. Remove jar and padding. CAUTION: Sharp blade inside blender jar.
5. Remove corrugated insert. Remove blender base from box and set aside.
6. Replace all corrugated inserts in the gift box and save the box for repacking.

REPACKING INSTRUCTIONS

1. Place blender on a large, sturdy flat surface.
2. Carefully place blender base in bottom of box.
3. Place long corrugated insert over base.
4. Insert blender jar and padding.
5. Close and seal box for shipping.

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed including the following:

1. READ ALL INSTRUCTIONS BEFORE USING.
2. Unplug from outlet when not in use, before putting on or taking off parts, and before cleaning.
3. To protect against electrical hazards, do not immerse the blender base in water or other liquid.
4. Do not use carbonated liquids in the blender jar, or any blending container. Using carbonated liquids in the blender jar or any blending container may result in injury.
5. Close supervision is necessary when any appliance is used by or near children.
6. Avoid coming into contact with moving parts.
7. Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or is dropped or damaged

in any manner. Return appliance to the nearest authorized service facility for examination, repair, or electrical or mechanical adjustment.

1. The use of attachments including canning jars not recommended by the appliance manufacturer may cause hazards.
2. Do not use outdoors.
3. Do not let cord hang over edge of table or counter, or touch hot surfaces.
4. Keep hands and utensils out of container while blending, to prevent the possibility of severe personal injury and/or damage to the blender. A rubber scraper may be used, but must be used only when the blender is not running.
5. Blades are sharp. Handle carefully.
6. Always operate blender with lid in place.
7. When blending hot liquids, remove center piece of two-piece lid. See Hot Blending instructions.
8. The use of ear protection is recommended during extended operating periods.
9. See Cleaning and Sanitizing instructions for all Waring Pro® Blenders. NOT FOR WATERJET CLEANING.
10. Do not operate your appliance in an appliance garage or under a wall cabinet. When storing in an appliance garage, always unplug the unit from the electrical outlet. Not doing so could create a risk of fire, especially if the appliance touches the walls of the garage or the door touches the unit as it closes.

SAVE THESE INSTRUCTIONS

MX1000R (Model: MXMPBKP6) BLENDER SPECIFICATIONS

• Capacity: 64 oz. working capacity
- Switch Settings: (2 Speeds) Hi Low Pulse
• Speed (RPMs) 30,000 26,000 30,000
• Rating: 120 Volts - 12.0 Amps
- Base Material: Polycarbonate
- Bearing: High Precision Ball Bearing
- Cord: 6-Foot Three-Conductor Ground Cord With Strain Relief in Base
• Overall Height: 19 inches
- Weight: 15 lbs.
• cETLus, NSF listed
- Operating Cycle: 1 min. ON/3 min. OFF

GROUNDING INSTRUCTIONS

• For your protection, this appliance is equipped with a 3-conductor cord set.
• 120 Volt units are supplied with a molded 3-prong grounding-type plug (NEMA 5-15P) and should be used in combination with a properly connected grounding type outlet as shown in Figure A.

If a grounding type outlet is not available, an adapter, as shown in Figure B, may be utilized to enable a 2-slot wall outlet to be used with a 3-prong plug (except in Canada and Europe). As shown in Figure C, the adapter must be grounded by attaching its grounding lug under the screw of the outlet cover plate.

Caution: Before using an adapter, you must be sure that the outlet cover plate screw is properly grounded. If in doubt, consult a licensed electrician.

Never use an adapter unless you are sure it is properly grounded.

Note: Use of an adapter is not permitted in Canada and Europe.

Green/Yellow: Earth/Ground. Blue: Neutral. Brown: Live.

Note: User-installed cord set plugs are not permitted in Europe.

This appliance is for 120 Volts only and should not be used with a converter.

MX1000R (Model: MXMPBKP6) OPERATION

1. Before starting, make sure that the blender is unplugged.
2. With the unit in OFF position, place container on blender base. Be sure container is fully seated and that drive coupling is properly engaged. Plug blender cord into outlet.
3. Put ingredients into container and cover it. Do not fill above MAX line.

WARING PRO 3 HP BLENDER NO LOW OFF PULSE

1. CAUTION: DO NOT use carbonated liquids in the blender jar or any blending container. Using carbonated liquids in the blender jar or any blending container may result in injury.
2. This blender has 2 speed settings: HI and LOW. Press paddle switch to desired position. To crush ice quickly, use HI speed setting.
3. When finished blending, set paddle switch to OFF position.
4. This blender is equipped with a pulse option. Hold paddle switch in the lower position to engage PULSE function. Unit will run on HI speed until the paddle switch is released.
5. Allow motor to come to a complete stop before removing container from blender base. Never place the container on the motor base or remove it from the motor base while motor is running.
6. Always hold container with one hand when starting and while blending. Never operate without jar lid.
7. Wash and dry container after each use. See Cleaning and Sanitizing instructions.

IMPORTANT HOT BLENDING INSTRUCTIONS

To minimize the possibility of being scalded when blending hot materials, the following precautions and procedure must be observed.

• Hot materials are those that are 100^ (38°C) or hotter.
• Limit the amount of materials processed to 1 pint.
• Completely remove the center portion of the two-piece container lid before starting motor (this will allow venting of the rapidly heated and expanding air inside the container when blender is running).
• Always start blending on lowest speed setting, and then progress to desired speed.
• Never stand directly over blender when it is being started or while it is running.

CLEANING AND SANITIZING INSTRUCTIONS

THE CONTAINER MUST BE CLEANED AND DRIED AFTER EACH USE OF THE BLENDER ACCORDING TO THE FOLLOWING INSTRUCTIONS. FAILURE TO DO SO MAY ALLOW RESIDUES OF PROCESSED MATERIAL TO COLLECT ON THE INTERNAL SEALS OF THE BLADE ASSEMBLY, RENDERING THEM INEFFECTIVE.

• Wash, rinse, sanitize and dry container prior to initial use and whenever it will not be used again within a period of 1 hour.
• Wash and rinse container after each use.
• Clean and sanitize motor base prior to initial use and after each use.
• Washing solutions based on non-sudging detergents and chlorine-based sanitizing solutions having a minimum chlorine concentration of 100 PPM are recommended.

The following washing, rinsing, and sanitizing solutions, or their equivalents, may be used.

SOLUTION PRODUCT DILUTION IN WATER TEMPERATURE
Washing Diversy Wyandotte 4 Tablespoons Hot 115°F (46°C)
*Diversol® BX/a or CX/A /Gallon
Rinsing	Plain Water		Warm 95°F (35°C)
Sanitizing	**Clorox®Institutional Bleach	1 Tablespoon/Gallon	Cold 50-70°F(10-21°C)

*Diversol® is a registered trademark owned by the Diversey Wyandotte Corp.

**Clorox ^® is a registered trademark owned by the Clorox Company.

• In repetitive batch-processing applications, frequent cleaning of the container will prolong the life of the blade assembly. In no case should actual running time between cleanings exceed 12 hour.
• Do not use container to store processed foods or beverages.

To wash and rinse container:

1. REMOVE CONTAINER FROM MOTOR BASE. Remove lid. Rinse container interior and lid under running water. Add washing solution to container. Scrub and flush out the container interior and lid to dislodge and remove as much food residue as possible. Empty container.

2. Wipe down exterior of container with a soft cloth or sponge dampened with washing solution. Wash lid and lid insert in fresh washing solution. Fill container 14 full with fresh washing solution, cover (with lid only but without center piece), place on motor base and run on HI for two (2) minutes. Empty container.

3. Repeat step (2) using clean rinse water in place of washing solution.

IMPORTANT

NOTE: IN ORDER TO MINIMIZE POSSIBILITY OF SCALDING, TEMPERATURE OF WASHING SOLUTION AND RINSE WATER MUST NOT EXCEED 115°F (46°C), AND QUANTITY USED MUST NOT EXCEED ¼-CONTAINER FULL.

IF HIGHER TEMPERATURES OR LARGER QUANTITIES ARE USED, OBSERVE ALL PRECAUTIONS GIVEN IN THE OPERATING MANUAL UNDER "HOT BLENDING INSTRUCTIONS."

To sanitize and dry container:

1. Wipe down exterior of container with a soft cloth or sponge dampened with sanitizing solution.
2. Fill container with sanitizing solution, cover, place on motor base, and run on high speed for two (2) minutes. Empty container. Dislodge any residual moisture from blade assembly by placing empty container on motor base and running on high speed for two (2) seconds.
3. Sanitize lid and lid insert by immersing in sanitizing solution for two (2) minutes.
4. Do not rinse container, lid, or lid insert after sanitizing is completed. Allow parts to air-dry.

To clean and sanitize motor base:

1. UNPLUG POWER CORD. Wipe down exterior surfaces of motor base with soft cloths or sponges dampened with washing solution, rinse water, and sanitizing solution. Prevent liquid from running into motor base by wringing all excess moisture from cloths or sponges before using them.

DO NOT IMMERSE MOTOR BASE IN WASHING SOLUTION, RINSE WATER OR SANITIZING SOLUTION.

1. Allow motor base to air-dry before using.

Any other servicing should be performed by an authorized service representative.

IMPORTANTES INSTRUCCIONES DE DESEMPACADO

Any other trademarks or service marks of third parties referred to herein are the trademarks or service marks of their respective owners.

©2012 Waring Consumer Products

150 Milford Road

East Windsor, NJ 08520

www.waringpro.com

Printed in USA