Tango HBH455 - Blender HAMILTON BEACH - Free user manual and instructions

Product Type	Blender
Brand	Hamilton Beach
Model	Tango HBH455
Category	Commercial Blender
Container Material	Stainless steel and clear polycarbonate
Included Capacities	0.9 L (32 oz) stainless steel and 1.4 L (48 oz) clear
Speeds	Low (LOW), High (HIGH), Pulse (PULSE)
Functions	Blending, chopping, sanitizing
Timer	Yes, integrated for precise control
Control Panel	HI/LO/PULSE buttons with timer
Safety	Built-in circuit breaker, safety lid, grounding required, automatic shut-off on overheating
Power Supply	120 V / 60 Hz, grounded plug
Daily Maintenance	Inspect blades and container for wear, cracks, or loose blades
Weekly Maintenance	Check condition of power cord and plug
Quarterly Maintenance	Replace container and blade assembly if worn or damaged
Cleaning and Sanitizing	Bleach solution (15 mL per 3.8 L of water) at low speed for 2 minutes
Spare Parts	Blades, containers, lid with gasket, fill plug, container support
Repairability	Contact Hamilton Beach technical service (866-285-1087 or commercial support)
Warranty	Consult manual or customer service for details

Frequently Asked Questions - Tango HBH455 HAMILTON BEACH

What to do if the blender does not start or stops during use?

Check that the plug is properly inserted into an electrical outlet. If the built-in circuit breaker has tripped, reset it. Also check the house fuses or circuit breakers. If the motor overheated, unplug the appliance and let it cool for 15 minutes before using it again.

Why are ingredients not blending properly?

Make sure to add enough liquid so the mixture is fluid. Solid pieces should not exceed 2.5 cm (1 inch). Do not fill the container beyond the maximum mark. Check that blades are sharp and not damaged. Use an appropriate speed for a homogeneous blend.

How to clean and sanitize the blender?

Prepare a solution of 15 mL (1 tablespoon) of bleach per 3.8 L (1 gallon) of cold water. Fill the container, put the lid on, and run at low speed for 2 minutes. Empty, then rinse with clear water. Wipe the exterior with a soft cloth soaked in the solution. For the lid and plug, immerse them in the solution for 2 minutes.

Can I blend hot liquids?

No, it is forbidden to blend hot liquids. This can damage the appliance and pose a burn risk. Use only room temperature or cold ingredients.

How to replace blades or container?

Inspect blades daily. If they are worn, chipped, cracked, or loose, stop use and replace the entire blade assembly. Never attempt to repair or tighten blades. Contact Hamilton Beach technical service for replacement parts.

Can I use an extension cord?

No, using an extension cord is prohibited. Plug the blender directly into a grounded outlet. Do not use an adapter either.

How to reset the built-in circuit breaker?

Locate the power switch/circuit breaker on the back of the blender. If it has tripped, press the reset button (usually red) to restore operation.

What safety precautions should I take?

Read all instructions. Do not leave the appliance unattended. Keep hands and utensils out of the container during operation. Always install the lid before starting. Unplug before cleaning. Use only on a stable, dry surface.

How to avoid damaging the blender?

Do not move or shake the appliance while it is running. If the mixture stops, turn off, remove the container, and use a spatula to push food toward the blades. Do not use a damaged container. Check blade condition daily.

Where to find spare parts and after-sales service?

For any assistance or parts ordering, contact Hamilton Beach technical service: USA/Canada at 866-285-1087 or by email at [e-mail]. For Mexico: 800 71 16 100, [e-mail].

USER MANUAL Tango HBH455 HAMILTON BEACH

Operation Manual – Original (2)

FR MÉLANGEUR POUR BAR

Line drawing of a Hamilton Beach blender with control panel and side view (no text or symbols on the device itself)

Line drawing of a Hamilton Beach blender with control knobs and a handle (no text or symbols on the device itself)

HBH455 Series
Série de HBH455
Serie de HBH455

Blender Safety

IMPORTANT: This operation manual should be reviewed with all equipment operators as part of your operator training program. Keep manual available in the work area for users' easy reference.

IMPORTANT SAFETY INSTRUCTIONS

WARNING – When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and/or injury to persons, including the following:

1. Read all instructions.
2. This appliance is not intended for use by persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they are closely supervised and instructed concerning use of the appliance by a person responsible for their safety.
3. This appliance shall not be used by children. Keep the appliance and its cord out of reach of children.
4. Close supervision is necessary when any appliance is used near children. Children should be supervised to ensure that they do not play with the appliance.
5. Plug into a grounded 3-prong electrical socket.
6. Do not remove ground prong.
7. Do not use an adapter.
8. Do not use an extension cord.
9. To protect against risk of electrical shock, do not put cord, plug, base, or motor in water or other liquid.
10. Do not spray the base with a high-pressure spray gun.
11. Turn the appliance OFF ☐), then unplug from outlet when not in use, before putting on or taking off parts, and before cleaning. To unplug, grasp the plug and pull from the outlet. Never pull from the power cord.
12. Avoid contact with moving parts.
13. Do not operate any appliance with a damaged supply cord or plug, or after the appliance malfunctions or has been dropped or damaged in any manner. Supply cord replacement and repairs must be conducted by the manufacturer, its service agent, or similarly qualified persons in order to avoid a hazard. Call the provided customer service number for information on examination, repair, or adjustment.
14. Do not blend hot liquids.
15. Do not use outdoors.

16. Do not let cord hang over edge of table or counter or touch hot surfaces, including stove.

17. Keep hands and utensils out of the jar and away from the cutting blade, while blending or chopping food, to reduce the risk of severe personal injury and/or damage to the blender or available attachments (attachments may not be provided with blender). A rubber spatula may be used but must be used only when blender is not running.

18. To prevent damage to blender, jar, or cutter assembly, DO NOT move or shake blender while in operation. If blending action stops during operation, turn blender OFF, remove jar from base, remove jar cover, and use a thin rubber spatula to push mixture toward cutters.
19. Blades are sharp; handle carefully—especially when emptying or cleaning the blender jar.
20. Inspect jar and cutter assembly daily. Do not use broken, chipped, or cracked jar. Check cutter for wear, nicks, or broken blades. Do not use broken or cracked cutting blades.
21. If cutter assembly blades are loose, discontinue use immediately and replace cutter assembly. Do not attempt to repair or tighten cutter assembly.
22. Always operate blender with cover in place.
23. Do not use appliance for other than intended purpose.
24. Do not leave blender unattended while it is operating.
25. Check that the appliance is OFF (☐) before plugging cord into wall outlet. To disconnect, turn the control to OFF (☐), then remove plug from wall outlet. To unplug, grasp the plug and pull from the outlet. Never pull from the power cord.
26. CAUTION! In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.

SAVETHESEINSTRUCTIONS

Safety Alert Symbols

The following safety alert symbols are used throughout this manual to alert you to the safety hazards described below.

Your safety and the safety of others is very important.

We have provided many important safety messages in this manual and on your appliance.

Always read and obey all safety messages.

This is the safety alert symbol. It is used to alert you to potential physical injury hazards.

Obey all safety messages that follow this symbol to avoid possible injury or death.

All safety messages will be preceded by the safety alert symbol and the word "WARNING" or "CAUTION." These words mean:

WARNING

!CAUTION

WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

All safety messages will identify the hazard, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

WARNING

Electrical Shock Hazard

Disconnect power before cleaning blender base.

Failure to follow these instructions can result in death or electrical shock.

WARNING

Electrical Shock Hazard

Plug into a grounded outlet.

Do not remove ground.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

Sanitizing

Sanitize using 1 Tablespoon (15 ml) of household bleach per 1 gallon (3.8 liters) of clean, cool water (60°F/16°C), mixed according to the instructions on the bleach.

1. Fill jar with sanitizing solution, replace lid and filler cap or dosing cup and run on LOW speed for 2 minutes. Empty jar.
2. Wipe exterior with soft cloth dampened with sanitizing solution.
3. Immerse lid and filler cap or dosing cup in sanitizing solution for 2 minutes.
4. Place empty jar on base and run on HIGH speed for 2 seconds to remove any moisture from the cutter assembly.
5. When ready to use, rinse with clean water.

WARNING

Cut Hazard

Always place cover on container when blending.

Do not put hands, spoons, or other utensils in container when blending.

Failure to follow these instructions can result in broken bones, cuts, or other injuries.

Technical Services

For assistance or replacement parts, call or email Technical Services:

USA, Canada: 866-285-1087 or [phone],

[e-mail]

Mexico: 800 71 16 100, [e-mail]

APAC Region: [phone], [e-mail]

www.hamiltonbeachcommercial.com

Parts and Features

Blender Base HBB255 Series HBH455 Series
Control Panel	OFF
Operation HIGH/LOW/PULSE		Timer Control HI/LO/PULSE
Removable Filler Cap X X
Lid w/Removable Seal X X
32 oz. Stainless Steel Jar X
*48 oz. Clear Jar X X
Removable Jar Pad X X
POWER/Circuit BreakerSwitch (back of Blender) X X

*NOTE: The maximum power rating is based on this container. The 32oz. container draws significantly less power.

Maintenance

Inspect the Blender and its various parts and replace as follows:

Daily	Unplug the Blender and remove the container from the Blender Base, then inspect the container and cutter assembly for wear, nicks, and broken or loose blades. Replace if necessary. If the blades are loose, discontinue use immediately and replace the blades.Do not attempt to repair or tighten the cutter assembly. See “Technical Services.”
Weekly	Unplug the Blender, then inspect the power cord insulation and power plug for cracks. Refer to “Technical Services” for repair or replacement.
Quarterly	Replace the container and cutter assembly as needed if inspection finds wear, nicks, or broken or loose blades. See “Technical Services.”

Troubleshooting

Problem Solution
Blender fails to start, or stops while it is running and cannot be restarted.	Check to see if unit is securely plugged into an electric outlet.Check to see if the integrated circuit breaker has tripped and reset it, if needed.Check to see if the fuse for the electric outlet has blown or if a circuit breaker has tripped.If the motor stops during operation due to overheating, unplug and allow the unit to cool down for 15 minutes. Plug unit back in after 15 minutes to resume normal operation.
Ingredients will not mix properly.	Check to see if enough liquid has been added to the ingredients. Mixture should be fluid and free-running at all times.Solid pieces are too large. Pieces should not exceed 1" cubes.Container is too full. Do not fill past highest graduation marking.Cutter unit blades are not sharp or are damaged. Inspect container and cutter assembly daily. Replace the container and cutter assembly as needed if inspection finds wear, nicks, or broken or loose blades. See “Technical Services.”Check to see if cutter assembly is installed properly.Select speed to create a fluid blend.

Line drawing of a hand pressing down on a device labeled 'Hamilton Beach' (no other text or symbols)

HBH455 Series
Série de HBH455
Serie de HBH455

Illustration of a person pouring liquid into a blender with a side panel (no text or symbols)

Illustration of hands using a power socket to switch a plug into an outlet (no text or symbols present)

Diagram showing a hand pouring liquid from a container into a tap, with an arrow indicating upward flow (no text or symbols present)

Illustration of a blender with three different actions: a brush, a mixing bowl, and a bottle (no text or symbols)

Diagram showing a kitchen appliance with three different parts, one being lifted by arrows (no text or symbols present)

Line drawing of a kitchen sink with faucet and fixtures (no text or symbols)

Line drawing of a hand operating a portable kitchen appliance with control knobs (no text or symbols)

Modelo: Tipos

HBB255 GB38

HBH455 GB39