Shark - Saw Westfalia - Free user manual and instructions

USER MANUAL Shark Westfalia

GB Original Instructions - Cordless Reciprocating Saw

Instruction manuals provide valuable hints for using your new device. They enable you to use all functions, and they help you avoid misunderstandings and prevent damage. Please take the time to read this manual carefully and keep it for future reference.

*ENGLISH The declared vibration total value and the declared noise emission values have been measured in accordance with a standard test method. The declared vibration total value may also be used in a preliminary assessment of exposure.

Warning!

The vibration and noise emission during actual use of the power tool can differ from the declared total value depending on the ways in which the tool is used, in particular, what kind of work piece is machined. It is necessary to identify safety measured to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time). Try to minimize the impact of vibration and noise. Exemplary measures to reduce vibration exposure include wearing gloves while using the tool, limiting working time, and using accessories in good condition.

SICHERHEITSHINWEISE

Please note the included General Safety Notes and the following safety notes to avoid malfunctions, damage or physical injury:

Please read this manual carefully and use the unit only according to this manual.

• When using the reciprocating saw, use safety equipment including safety glasses and ear protection. If the work produces dust wear respiratory protection suitable for the work being undertaken. If operating the tool causes discomfort in any way, stop immediately and review your method of use.
• Dispose of used packaging material carefully or store it out of the reach of children. There is a danger of suffocation!
• Persons with limited physical, sensorial or mental abilities are not allowed to use the unit, unless they are supervised and briefed for their safety by a qualified person.
• Always hold the tool by the insulated gripping surfaces. Operations where the tool, fitted accessories or fasteners may contact hidden 'live' wiring will make exposed metal parts of the tool 'live' and cause an electric shock hazard to the operator.
• Always grip the tool firmly, do not overreach, and ensure you won't lose control. Keep secure footing whilst using a reciprocating saw.
• Battery chargers are for indoors use only. Ensure that the power supply and charger are protected against moisture at all times.
• Please read this manual carefully and use the unit only according to this manual.
• Keep hands away from the sawing range. Do not reach under the workpiece. Contact with the saw blade can lead to injuries.

• Apply the machine to the workpiece only when switched on. Otherwise there is danger of kickback when the cutting tool jams in the workpiece.

• When the cut is completed, switch off the machine and then pull the saw blade out of the cut only after it has come to a standstill. This way you can avoid kickback and can place down the machine securely.

• Use only sharp, flawless saw blades. Bent or blunt saw blades can break or cause kickback.

• Do not slow down the saw blade by applying side pressure after switching off. The saw blade can be damaged, break or cause kickback.

• Do not cut or saw where there might be hidden electric wires, gas or water pipes.

• Use suitable detectors to determine if utility lines are hidden in the work area or call the local utility company for assistance. Contact with electric lines can lead to fire and electric shock. Damaging a gas line can lead to explosion. Penetrating a water line causes property damage or may cause an electric shock.

• Ensure that the lighting is adequate.

• Ensure that the reciprocating saw blade is securely fixed in the holder. Insecure accessories can be ejected from the machine causing a hazard.

• Do not exert pressure on to the tool. To do so would shorten its service life.

If you are interrupted when operating a reciprocating saw, complete the process and switch off before looking up.

• Where possible, use clamps or a vice to hold your work.

• Examine the tool holder regularly for signs of wear or damage. Have damaged parts repaired by a qualified service centre.

• Always wait until the reciprocating saw has come to a complete stop before putting it down.

• Periodically check all nuts, bolts and other fixings and tighten where necessary.

• Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

Additional Battery and Charger Safety Notes

WARNING: Li-lon batteries, if incorrectly used, stored or charged are a fire, burn and explosion hazard.

Use the battery charger correctly

Refer to the section of this manual relating to use of the battery charger before attempting to charge the battery.
- Do not attempt to use the charger with any batteries other than those supplied. Failure to follow these instructions may cause overheating or fire.
- When battery pack is not in use, make sure the battery pack cannot be shorted accidentally. Keep the battery clean at all times. Keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
- Allow batteries to cool for 15 minutes after charging or heavy use. Failure to follow these instructions may cause overheating or fire.
- Use only chargers recommended by the manufacturer to charge the batteries. If a charger is not suitable for a certain kind of battery there is a risk of fire. Only use Li-Ion batteries provided with a product or specifically designed to be compatible.
- Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
- The unit is designed for operation in altitudes of up to 2000m above sea level.
- Keep the battery out of reach of children.
- When not in use batteries should be stored at room temperature (approximately 20^ C).
- Do not open, disassemble, crush, heat above 60^ C or incinerate. Do not dispose of in fire or similar.
- Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
- Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
- Do not use damaged or modified batteries. Damaged or modified batteries may act unpredictable and cause fire, explosions or physical injury.
- Do not expose a battery to fire or excessively high temperature. Fire or temperature in excess of S 130^ may cause an explosion.
- Follow all Instructions for charging and never charge the battery outside of the temperature range between 0 and 40^ C. Incorrect charging or

charging outside the permitted temperature range may destroy the battery and cause a fire.

• Never perform maintenance on a damaged battery. Maintenance may only be performed by the manufacturer or authorized service personnel.

Batteries do not belong in the household garbage.

For battery disposal please check with your local council.

CONSOGNES DE SECURITE

declare by our own responsibility that the product

12 V Li-Ion Akku Säbelsäge "Shark"

12 V Li-Ion Reciprocating Saw "Shark"

Articlel Nr. 94 53 55

Article No. 94 53 55

is according to the basic requirements, which are defined in the European Directives and their amendments.

2011/65/EU

Restriction of the Use of certain hazardous Substances in electrical and electronic Equipment (RoHS)

2014/30/EU

The technical documentations are on file at the QA department of the Westfalia Werkzeugcompany.

Hagen, den 24. September 2021

Hagen, 24^th of September, 2021

zhong jingling 电子

Please help avoid waste materials.

If you at some point intend to dispose of this article, then please keep in mind that many of its components consist of valuable materials, which can be recycled. Please do not discharge it in the rubbish bin, but check with your local council for recycling facilities in your area.