Px7 S2 - Earphones BOWERS & WILKINS - Free user manual and instructions

Product Type	Bluetooth wireless over-ear headphones
Brand	Bowers & Wilkins
Model	Px7 S2
Weight	310 grams
Battery Type	Rechargeable lithium polymer
Battery life	Up to 30 hours with active noise cancellation (ANC) and Bluetooth; 5 hours with 15 minutes of quick charge
Charging time	Up to 3 hours for full charge
Transducers (speakers)	2 × 43.6 mm full range
Frequency response	10 Hz to 30 kHz
Input impedance	20 kOhms
Distortion (THD)	<0.3% (1 kHz / 10 mW)
Bluetooth version	Bluetooth 5.0 with aptX Adaptive
Supported Bluetooth codecs	aptX Adaptive, aptX HD, aptX Classic, AAC, SBC
Active noise cancellation	Yes, adaptive with High, Low, Auto, Off modes
Ambient sound passthrough	Yes, activated via the noise cancellation button (press and hold 2 seconds)
Wear sensors	Yes, wear detection with auto pause/standby
Microphones	4 mics for noise cancellation, 2 mics for telephony (CVC2)
Connectivity	Bluetooth, 3.5mm audio jack, USB-C (audio and charging)
Included accessories	Carrying case, 3.5mm audio cable, USB-A to USB-C cable
Maintenance and cleaning	Clean with a soft, slightly damp microfiber cloth; do not use detergent or abrasive products
Reset	Restore factory settings by holding down the Volume +, Volume -, and Noise cancellation buttons for 10 seconds
Mobile app	Bowers & Wilkins Headphones app (iOS and Android) for custom settings and firmware updates

Frequently Asked Questions - Px7 S2 BOWERS & WILKINS

How do I pair my Px7 S2 headphones with a phone?

Turn on the headphones by sliding the power switch up. Pairing mode is active by default. If not, hold the switch up (Bluetooth symbol) for 5 seconds until the light flashes blue. On your phone, enable Bluetooth and select Px7 S2 from the device list.

What is the battery life?

Battery life is up to 30 hours with active noise cancellation and Bluetooth enabled at moderate volume. A 15-minute quick charge provides 5 hours of playback.

How do I change the noise cancellation mode?

Use the noise cancellation button on the left earcup to cycle through modes: High (very noisy environments), Low (environmental awareness), Auto (adaptive), and Off.

Does the wear detection function work with glasses?

Yes, but glasses arms or hair can interfere with the sensors. Ensure no obstructions between your ears and the ear cushions for optimal operation.

How do I clean my Px7 S2 headphones?

Use a soft, slightly damp microfiber cloth. Dab gently without rubbing. Do not use detergent, soapy water, wax, or chemical cleaners, and avoid paper towels.

Can I use the headphones while charging?

Yes, the headphones can be used while charging. Plug the provided USB-C cable into a power source (wall charger or computer) and connect to the headphones.

How do I activate Ambient Pass-Through?

Press and hold the noise cancellation button on the left earcup for 2 seconds. Release to toggle between pass-through mode and the previous noise cancellation mode. The level can be adjusted in the app.

Can I connect two Bluetooth devices at the same time?

Yes, the Px7 S2 can be connected to two devices simultaneously. To switch, pause playback on the first device and start playback on the second. An incoming call during playback automatically interrupts the music.

How do I reset the headphones to factory settings?

When the headphones are on, press and hold the Volume +, Volume -, and Noise cancellation buttons simultaneously for 10 seconds until the light turns off and then back on. The paired devices list will be cleared.

What cables are included with the headphones?

The box contains a 1.2m 3.5mm stereo audio cable, a 1.2m USB-A to USB-C cable for charging and audio, and a carrying case.

USER MANUAL Px7 S2 BOWERS & WILKINS

PX7 Wireless Headphones

Welcome to Bowers & Wilkins and PX7

Thank you for choosing Bowers & Wilkins. When John Bowers first established our company, he did so in the belief that imaginative design, innovative engineering and advanced technology were keys that could unlock the enjoyment of audio in the home. His belief is one that we continue to share and inspires every product we design, tailored for new audio experiences outside of the home.

The Bowers & Wilkins PX7 are high performance over-ear headphones designed to deliver the highest quality mobile personal audio experience combined with the convenience of wireless operation and the serenity of noise-cancellation. This manual will tell you everything you need to know to get the most from your PX7 headphones.

Your PX7 can play music streamed wirelessly from your mobile phone, tablet or computer via Bluetooth, or conventionally connected by a jack cable to a suitable analogue headphone output. PX7 can also play audio via a USB connection from a computer and can be used for wireless telephony.

PX7 Real World Listening features include our latest innovations in Adaptive Noise Cancellation, Ambient Pass-Through and enhanced Wear Sensing technologies. Our latest generation noise cancellation feature was designed from the ground up with intelligent environment sensing capabilities, automatically selecting the appropriate type of noise cancellation best suited to your surrounding environment, its only goal is to deliver an uncompromised listening experience. Ambient Pass-Through enables external sounds, such as conversation or safety announcements, to be heard clearly without any need to remove the headphones. The Wear Sensing feature enables PX7 to respond naturally, pausing and resuming the music simply by lifting either earpiece on or off your ear. These features can be enabled and further customised via the Bowers & Wilkins Headphone App available for free on iOS and Android devices.

PX7 incorporates a rechargeable battery pack. When fully charged, depending on the degree of Bluetooth, Adaptive Noise Cancellation and Ambient Pass-Through use, the battery pack can provide up to 30 hours of continuous wireless media streaming with noise cancellation enabled at average playback volume levels.

1.PX7 Carton Contents

PX7headphones

Storage case

USB-C charging cable

3.5mm audio cable

Document pack

2. Getting to know your PX7

2.1 Switching Headphones On and Off

Diagram 1 illustrates power switch functionality.

Switching On

The Power Switch is located on the right earpiece. Slide the Power Switch up to the middle position. An audible cue will be presented and the LED indicator will light up in either green, amber or red displaying the current charge level.

Switching Off

Slide the Power Switch to the bottom position.

An audible cue will be presented and the

headphones will power down when the LED

indictor is no longer lit.

2.2 Headphone Controls

Diagram 2 illustrates the headphone controls. The following buttons on the right earpiece are used to for media playback:

Function Action

Play or pause	Press the Multi-function button once.
Play to next track	Press the Multi-function button twice in quick succession.Note: functionality dependent on source device.
Play previous track	Press the Multi-function button three times in quick succession.Note: functionality dependent on source device.
Increase Volume Press the Volume + button.
Lower Volume Press the Volume - button.

The following buttons on the right earpiece are used for phone call functionality:

Function Action

Answer or end call	Press the Multi-function button once.
Answer an incoming call	When incoming call occurs, press the Multi-function button once.
Decline an incoming call	When incoming call occurs, hold the Multi-function for 2 seconds.
Switch between two calls	With two calls active, press the Multi-function button twice.
Merge two calls	With two calls active, hold the Multi-function button for 1 second.
Toggle mute	While on a call, press the Multi-function button three times.

2.3 Status Indicator

The status LED indicator is located on the right earpiece, Diagram 3 explains the illumination states.

Diagram 1

Power switch functionality

Diagram 2

Headphone controls

Illumination Operational state

White Battery charge > 30%

Amber Battery charge between 30% and 10%

Red Battery charge < 10%

Red flashing Battery charge insufficient for headphone operation

Blue flashing Pairing mode enabled

Blue (2 sec solid) Pairing successful

Blue flashing (calls) Incoming call

Green flashing Rapid charging

Green solid Battery charge full, trickle charging

Diagram 3

Status indicator illuminations

3. Intelligent Features

3.1 Adaptive Noise Cancellation

Noise cancellation is a series of advanced technologies that aids in removing undesired noise from the surrounding environment.

PX7 features our latest innovations in adaptive noise cancellation, this includes intelligent sensing that adapts noise cancellation and tuning best suited to your surrounding environment. As your surroundings change, noise cancellation will auto adapt to complement your new environment.

The Noise Cancellation button on the left earpiece is used to cycle between the following modes, see Diagram 2 for button location:

Mode Application

High	Suitable for consistently noisy environments such as an airplane cabin.
Low	Suitable for environments where you need awareness of your surroundings.
Auto	Intelligently adapts noise cancellation best suited to your current environment.
Off Turns off the noise cancellation feature.

3.2 Ambient Pass-Through

PX7 features ambient pass-through which lets some external noise from the surrounding environment, such as safety announcements or conversations, to be heard without taking the headphones off.

The Noise Cancellation button on the left earpiece also controls this feature, see Diagram 2 for button location.

Function Action

Enable ambient pass-through	Press and hold the Noise Cancellation button for 2 seconds.
Disable ambient pass-through	With ambient pass-through enabled, either hold down or single press the Noise Cancellation button for 2 seconds, the headphones will return to the previous noise cancellation mode

The level of ambient pass-through can be further customised to suite your needs using the Bowers & Wilkins Headphones App.

3.3 Wear Sensors

PX7 incorporate our latest enhanced wear detection sensors in both earpieces, see Diagram 4, enabling intelligent battery conservation by entering standby when removed from the head. When worn again, PX7 automatically wakes and connects to the last connected Bluetooth device.

During media playback, PX7 will auto pause when either earpiece is lifted from the ear. Playback will auto resume when the earpiece is placed back on the ear. Auto resume has been further optimised so it is ready only when you are. This means the headphone will not attempt to resume playback during following conditions:

1. Headphone powers on from the off state.
2. Headphone wakes from the standby state.
3. Headphone reboots (such as after a factory reset).

Wear sensor and standby can be adjusted using the Bowers & Wilkins Headphones App.

Note: Take care when wearing your headphones; hair or accessories trapped between your ears and the earpieces, or wearing glasses that distort the profile of your ears, may interfere with the performance of the proximity sensors.

Diagram 4
Wear sensor location

4. Battery Charging and Power Saving

Your PX7 comes with the battery partially charged may be used immediately. For best practice we recommend to fully charge the headphones before first use. Please allow up to 3 hours for full charge. The headphones can be used while charging.

To charge:

1. Please use the supplied charging cable and connect the USB-A plug to a wall charger or a powered computer USB-A socket.
2. Then connect the USB-C end to the headphones USB-C socket

Note: During charging, the headphone indicator will flash green. When fully charged, the indicator will remain illuminated. See Diagram 3 for status indicator details.

4.1 Standby Power Saving

PX7 wear detection sensors intelligently conserve power. When taken off your head, PX7 will automatically enter standby which will pause media playback, disconnect Bluetooth and switch to a low power state.

When worn again, PX7 will wake and reconnect to the last connected Bluetooth source. Note that both earpieces must detect wear for proper functionality. If wear sensors are disabled using the app, this feature will also be disabled.

With the app, you can customise how long the headphones will wait before switching to auto standby, please see Standby Timer under Settings in the app.

5. Wearing Your Headphones

Wearing your headphones correctly will help ensure the best possible experience. See Diagram 6.

1. Identify the left and right earpieces by finding the identification legends located on the interior of each earpiece.
2. Wear the headphones accordingly with the headband adjusted so that the they rest comfortably on your head.

Note: Wearing glasses that distort the profile of your ears may interfere with headphone performance. Similarly, hair trapped between your ears and the headphone ear-pieces may interfere with the wear sensor performance.

Diagram 5 USB-C cable connection

Diagram 6 Wearing your headphones

6. Bluetooth Connection

6.1 Pairing

PX7 is designed to stream media wirelessly from Bluetooth audio devices, such as smartphones, tablets or personal computers. To do so, the headphone and device (source) must first be paired.

1. The first time you switch on your headphones, Bluetooth pairing mode will be enabled, the indicator will flash blue. If pairing mode is not enabled, please slide and hold the power switch to the upper (Bluetooth Icon) position for 5 seconds, let go when the indicator blinks blue and when an audible cue is presented.
2. Ensure the Bluetooth feature is enabled on the audio device, PX7 will appear in the discovery list, select it to pair.
3. The indicator will flash blue while pairing is in progress, this will change to solid blue and an audible cue presented when pairing is successful.

Your headphones will remember up to eight paired Bluetooth devices. Repeat the above steps to pair more devices.

Note: Your headphones will automatically exit Bluetooth pairing mode if no device is paired within 5 minutes. If pairing fails, the indicator will rapid flash blue, please try pairing again.

6.2 Multiple Bluetooth Connections

PX7 can connect up to two devices at the same time, but note that you can only play audio or take calls from one device at a time.

To switch between two devices:

1. Pause audio on the first device, or use the PX7 multi-function button.
2. Play audio from the second device and the headache will switch over.

When streaming audio, receiving a call on the second device will automatically pause playback and the call will be routed automatically to your headphones. Ending the call will automatically resume playback from the first device.

6.3 Disconnect from a Device

You can quickly disconnect PX7 from a device by sliding the Power Switch to the upper (Bluetooth Icon) position two times in quick succession, an audible tone will be presented indicating successful disconnection.

Alternatively, you can manage connection in further detail using the Bowers & Wilkins Headphones app under Connections.

6.4 Setting Up Headphones with the App

The Bowers & Wilkins Headphones app provides extended setup and adjustments to features such as Adaptive Noise Cancellation, Ambient Pass-Through, and Wear Sensors. The app also provides further customisations such as voice prompt, standby time, connection management and headphone software updates. The app is available as a free download on iOS and Android devices.

To add your headphones:

1. From your mobile device, download and install the Bowers & Wilkins Headphones app.
2. Launch the app, then read and follow the instructions pertaining app notification and permissions.
3. After reaching the main screen, simply tap + and following the in-app instructions.

6.5 Headphone Software Updates

Bowers & Wilkins will occasionally make available software updates that refine and optimise the performance of your headphones or add new features.

The Bowers & Wilkins Headphones app will notify you when a software update is available, tap on the notification and the follow in-app instructions.

Diagram 7 Bluetooth pairing

7. Auxiliary Connection

In addition to Bluetooth, your PX7 can also connect to audio sources using the supplied 3.5mm audio or USB cables.

7.1 Connecting with the 3.5mm Audio Cable

The 3.5mm audio cable enables your PX7 to be used with a device supporting an analogue output such as a conventional headphone socket on smartphones or tablets, or a traditional hi-fi system. See Diagram 8.

1. Insert the 3.5mm audio cable into the headache 3.5mm socket on the right ear piece.
2. Take the other end and insert into the appropriate socket on your device.
3. Your PX7 will automatically disconnect from any Bluetooth devices.

Note: Your headphones must have sufficient charge and switched on to play audio from an analogue source device. The volume and play/ pause buttons will not function when using the 3.5mm interface.

7.2 Connecting with the USB Cable

USB connection enables your PX7 to function as a USB sound output device when connected to a capable computer.

1. Insert the USB-C end into the PX7 USB-C socket on the right ear piece.
2. Take the USB Type A end and insert into the appropriate socket on your computer.
3. PX7 will automatically disconnect from any Bluetooth devices.
4. Find and select your headphones from the computer's audio output control panel.

Note: When connected to an capable computer USB port, the headphone battery will also charge.

8. Power Cycle and Reset

8.1 Power Cycle

You can power cycle your PX7, simultaneously hold the Volume + and Volume - buttons for 10 seconds until the indicator LED extinguishes, let go when the indicator lights up again. Rebooting your headphones will not reset their internal settings or clear the paired device history.

8.2 Reset to Default

You can clear the paired device history and restore all settings to their defaults. With PX7 powered on, simultaneously hold the Volume +, Volume - and Noise Cancellation buttons for 10 seconds until the indicator LED extinguishes, let go when the indicator lights up again, the headphones will be ready to pair to a device. Alternatively, you can reset from the Bowers & Wilkins Headphones app, please see Reset under Settings in the app

9. Care & Maintenance

9.1 Storing Your PX7

Taking care of your PX7 will ensure they continue to deliver the best performance and experience.

When not used, stow your headphones using the included storage pouch. It is recommended the headphones are first powered off:

1. Retract the headband on each side so they are in the smallest position.
2. With the buttons facing you, rotate the earpieces inwards so they lay flat.
3. Place the headphones in to the storage case.

9.2 Cleaning Your PX7

Your PX7 can be cleaned by a soft, damp microfiber cloth, gently wipe or dab clean.

The fabric on PX7 have been specially coated with moisture and stain repellent. If dirt, stain or fibre residue accumulate on the fabric surface, please clean as instructed above.

• Do NOT aggressively rub or use an abrasive tool to clean, especially the fabric.
• Do NOT use paper towels, napkins or tissue as they will leave residue.
• Do NOT use cleaning detergents, soapy water, polish or chemical cleaners.
• Ensure that no moisture get inside the earpieces, buttons and interface ports.

10. Support

Should you require further help or advice regarding your PX7 please visit the Headphones support site here www.bowerswilkins.com/support.

Environmental Information

This product complies with international directives, including but not limited to the Restriction of Hazardous Substances (RoHS) in electrical and electronic equipment, the Registration, Evaluation, Authorisation and restriction of Chemicals (REACH) and the disposal of Waste Electrical and Electronic Equipment (WEEE). Consult your local waste disposal authority for guidance on how properly to recycle or dispose of this product.

Specifications

Wearing Style Bluetooth Wireless Over-Ear Headphones

Technical Features Adaptive Noise Cancellation

Ambient Pass-Through
Wear-Detection Sensor
Bluetooth® audio - Bluetooth 5.0 with aptX™ Adaptive
USB-C charging & audio interface
3.5mm auxiliary audio interface

Bluetooth Codes aptXTM Adaptive

aptXTM HD
aptXTM Classic
AAC
SBC

Bluetooth Profiles A2DP v1.3.1

AVRCP v1.6.1
HFP v1.7.1
HSP v1.2
BLE GATT (Generic Attribute Profile)

Drive Units 2 x 0 43.6mm full range

Microphones 4x mics for ANC

2x mics for telephony (CVC2 - Clear Voice Communication v2)

Frequency Range 10Hz to 30kHz

Input Impedance 20 kOhms

Distortion (THD) < 0.3% (1kHz/10mW)

Battery Type Rechargeable Lithium Polymer

Battery Life & Charging 30 hrs Bluetooth with ANC, 5hrs with 15min charge

Inputs Bluetooth, 3.5mm stereo jack, USB-C audio

In Box Accessories 1.2m stereo audio cable, 1.2m USB-A to USB-C cable, Storage Case

Weight 310 grams

Figure 7 Jumelage Bluetooth

Ambient Pass Through

Naherungssensor

Distorsione (THD) <0.3% (1 kHz/10 mW)

3.1 Adaptive Noise Cancellation

3.2 Ambient Pass-Through

Ambient Pass-Through

Draagsensor

Bluetooth® audio - Bluetooth 5.0 met aptXTM Adaptive

USB-C Iaad- & audio-ingang

BecnpoBOHbIe HAYsHnKPNX7

3aunTHaCyMoOka

Ka6enbIaapKcUSB-CpaBemaM

3.5-MM ayuoc Ka6enb

KOMnckTdoKymeHTaun

2.3HaKOMCTBOcHayuHnKamu PX7

2.1 BkHoueHne/BybKIOueHne HayuHkoB

Ha Diagram 1 nokaaHbI cyHKmCdBHXHO nepeKIOHATena Power (BKn/BkN).

BkIouyHeH

IpeKnHcPb Power pacrnooxh Ha npabOy aUaKc Hayunko.CuBnHe IepKoHanty HntAHH CpeJHnpoXeH. HayunHKnNnJdJIy BAYKO BOrHAn, aCBTOIOHDn HNDNKATOp 3aOpTOn 3eEHHM, XeBHm NnKPachM UBeTOM, OTo6pKaar TeKuym npoeBb 3apda.

BbIKIOeHne

CpBnHBe BkHKeHATEB NHTAHRA H KHeE NOXeHHe. HayIiHKnOaRbNdAyt 3KkoBc CnHan n BkHIOHATc, aCBTOJNOHbHMHKATOP NORACHET.

2.2 YnpabHeHne HayuHkamn

Ha Diagram 2 noka3aHb opraHb ynpabneHnHauyuHKAMn. DnIyprabneHn Bocipow3BeHnemayno no Bluetooth moKHO nCNOB3CBATcpekyoKe HKNKn Ha npabO hKNe HauHHKO:

ФУHKUHДENCTBNE

Восчима��ен (Play) ини раду (Pause)	Haxmite Ha MHOROФYКДСHAньHyо KНОКу ODINH рад.
Перейтк восчима��ен сенийсяю оке	Haxmite Six tro 2 pada Ha MHOROФYКДСHAньHyо KНОКу, ПОПМЕЧИЕ: blyIOJIENHUE 3OTN KOMAHДБ 3BAMCNIT OT NCTOCHNK
Перейтк восчима��ен прд�йсяю оке	Haxmite Six tro 3 pada Ha MHOROФYКДСHAньHyо KНОКу, ПОПМЕЧИЕ: blyIOJIENHUE 3OTN KOMAHДБ 3BAMCNIT OT NCTOCHNK
Повыкову гомКоctь	Haxmite Ha KONKY Volume +
СпуньштгомКоctь	Haxmite Ha KONKY Volume -

TnTepeohhixpa3IOOBPOBNCIOJIbSyTE CIEpyIOUe KHOIKH HAPBOB YAIIKE HAYIHNKOB:

ФУHKUNAДeINCTBNE

3.5mm aydno Bxod AUX

Bluetooth kodek aptX™ Adaptive

aptXTM HD

aptX™ Classic

AAC

SBC

Bluetooth npoФmU A2DPv1.3.1

AVBCPv1.6.1

HFPv1.7.1

HSPy1.2

BLE GATT (Generic Attribute Profile)

HAMK2x43.6MM,NOHOmana30HHbE

Mkpoohb4xMknpoohaAANC,

2x MMKpOoHa JnTnePohnn (CVC2-Clear Voice Communication v2)

Hnanaohyacto10T-30K

BxOHHIIMnDAnC 20KOM

UckaeHHN（THD）<0.3%（1KΓL,10MBt)

AkkymyantopIITnMeBO-nOMpeHbI

Bpma pa6o 30acob Bluetooth c ANC,5acoc noce 15 mHyt 6bctpoaep

Bxodbl Bluetooth,3.5-crepeo paabeM,USB-C pna aymo

Ppnaembeakceccyapbl 1.2 M crepeaayno kaebb,1.2 M USB-A-USB-C kaeibcymoKa pxaHn

Bec 310r

Kaωoopiατε στην Bowers & Wilkins kal ta akouotικa PX7

Zac euxapiotoue nou eIaeate tv Bowers & Wilkins. O John Bowers 1bpue Tnv talaepia mac tnv npoiOnon oti n eufavtaoTn oxediaon, n kaivotouia otnv avantuEknai n Eeluyevn texvoLoyia thav ta kleidia nou 0a aovayv evouc kououc anolauong tou nxou oTo oTI. Autnv tnV niotn tou ouvexizoue va moipaQpaote kal eumvei kaThe npoiov nou oxediaoue, npoapmuoeyn yia vec nxtikec empiiec ektoC ontiou.

Ta Bowers & Wilkins PX7 εival akouotiká κεφañç vψηλñç anóðoŋc, oxéδiaσμéva wotε va oac napéxouv tnv kaúτepn duvatn nxtiκn επεipia yia φopntéc ouokéuεc, σε ouvduaσo με tnv avεon tnc aoupuatnc λεitoupyiac kau tn yaλvn tnc εξouδεtερωoç θορúβou. ζε auto to εγχεipidio θa μαθετe oλa oσa πpêπει va γνωpiζετ, γia va aξioptoiσετο Το επakpo ta akouotiká PX7.

Ta akouotiká PX7 μπopouv va avanapayouv aoupuatn po nouoknc ano to kivnto tnoéwvo, to tablet n tov unoloyiotn oac μeow Bluetooth n eovc kaωdiou ouβaṭiKa ouδεμevou μe βuσa σ εia katαληn avaloyikn édo akouotikw. Ta PX7 μπopouv επionc va avanapayouv nxo μeow ouδεonc USB aó evav unoloyoiotn, kaθwca va xρημoioŋθouv yia aoupuatn tnoεφωvia.

Oi duvatoTntc Real World Listening (PpaymuTikn akpoaon)Twv akouotikwv PX7 TepiaaBavovuTvC TELAutaicmuac KaVOTUIEC OTIC TEXVOLOYIEC Adaptative Noise Cancellation (Ppooapuoottikn EGSdtepwnoopou), Ambient Pass-Through (AeEauon nXou PEPiAALovTOC) kai BELTIomega nTExvoLoyia Wear Sensing (Avxveun xpnoanc). H TELAutaia mAc Yevia TEXVOLOYIAc EGSdtepwonc 0opubou oxediaoNTK e ano undeltaviki nBaon me EEUTVEc duvatoTntc avixveoun cpeipalovTOC, yia autouatn EINAOyN tou kaTALNOU tTou EGSdtepwonc 0opubou nou eiva kalutePOC yia to ppiBalaov OAC, e anokleiotko otxo va npexei mia anapamlln emepia aKOaONc. H duvatoTnta Ambient Pass-Through (AeEauon nXou PEPiAALovTOC) EITpETeI va akouyovta Kaapac EEWTEPIKoi nXoi, oTWC ouZntnoic n avakoivwoeic aphiiaac, xwpic va xpeiazetai va aphipethetaov ta akouotika. H duvatoTnta Wear Sensing (Avxveun xpnoanc) EITpETeI OTA PX7 va avtanokpivovtai e fuokotna, ppayaToTowvTac paocn Kal ouvexion tnC moouknc otav avaonkwveTe eva ano ta akouotka ano to auTi oac. Autec oI duvatotntc mTopovva evpyoioTHouv kai va ppoapuooTOv PepaTEpW eoswn c efapouyn C Bowers & Wilkins Headphones nou eivai diaheoiu nDpwEv osoKEuec me Aetoupkyo ootma iOS kai Android.

Flapapoppwn (THD) < 0.3% (1 kHz/10 mW)

Tunocmuataipac Enavaopotizcpeynaiounoaepooc

Bowers & Wilkins Headphones App 1

6.4 云王三

PX7E DTHH HJH 0000000000000000000000000000000000000000000000000000000000000000000000000000

世界

B&W 《 REACH)和

吉

德三元电

吉

HH H

首号网

USB-C 电电电

3.5mm

Bluetooth CoMx Aptx-Adaptive

Aptx-HD

Aptx-Classic

ACC

SBC

Bluetooth 手机版 A2DP v1.3.1

AVRCPv1.6.1

HFP v1.7.1

HSP v1.2

BLE GATT (Generic Attribute Profile)

2x43.6mm

HOJ34XANCHOJ3

2x 音生马贝（CVC2-ClearVoiceCommunicationv2)

孕用多 10Hz～30kHz

120

0.3%（1KHz/10mW）

田T

B

日

1.2m USB-A USB-C

310g