Life Dot 2 - Helmet soundcore - Free user manual and instructions

USER MANUAL Life Dot 2 soundcore

• Open or close the charging case to activate the LED battery indicator.

• Fully charge both the earbuds and the charging case before the rst use.

• To prevent damage, use the provided USB-C cable.

• Fully dry off the earbuds and the USB port before charging.

LED indicator Flashing red Low battery Steady white Being charged Light off Fully charged Powering On/Off The earbuds will automatically power on when taken out of the charging case and power off when placed back into the charging case.

• To manually power on, press and hold the multi-function button on both earbuds for 1 second until the LED indicator turns white for 1 second.

• To manually power off, press and hold the multi-function button on either earbud for 8 seconds until the LED indicator turns red for 1 second. Pairing True Wireless Stereo Connection The right earbud will automatically connect with the left earbud when taken out of the charging case. LED indicator (Earbuds) Slowly ashing white TWS connecting Rapidly ashing white (Primary earbud) Slowly ashing white (Secondary earbud) TWS connected

• The right earbud is the primary earbud by default. In TWS mode, place either one of the earbuds into the charging case, the other one will switch to be the primary earbud.

• When powered on and connected, if either one of the earbuds is out of battery and powered off, you can keep using the other one. Bluetooth Pairing with your Device

1. Take the earbuds out of the charging case or manually power on the earbuds, the

earbuds enter the Bluetooth pairing mode successfully when the LED indicator on either earbud ashes white.

2. Turn on Bluetooth on your device and click “Soundcore Life Dot 2”. The LED

indicator on either earbud will turn white for 1 second when Bluetooth connected.03 EN Soundcore Life Dot 2 Soundcore Life Dot 2 LED indicator (Earbuds) Rapidly ashing white Bluetooth pairing Steady white for 1 second Bluetooth connected

• When earbuds are out of the charging case and powered off, to manually enter Bluetooth pairing mode, press and hold the multi-function button on both earbuds for 3 seconds.

• Each time you power on your Soundcore earphones, it will automatically connect to your last successfully connected device if available within the Bluetooth range. Wearing

1. Choose the EarTips and EarWings that t your ears best.

2. Insert the earbuds into the inner canal of your ears.

3. Turn and nd the most comfortable position.EN 04

Button Controls Play / Pause Press once (L or R) Next track Press and hold for 1 second (R) Previous track Press and hold for 1 second (L) Volume up / down Control volume via the connected device Answer / End a call Press once (L or R) Put the current call on hold and answer an incoming call Reject a call Press and hold for 1 second (L or R) Transfer a call between earphones and mobile phone Switch between held call and active call Activate Siri or other voice assistant software Press twice (L or R) Mono mode Play / Pause Press once (L or R) Answer / End a call Reject a call Press and hold for 1 second (L or R) Activate Siri or other voice assistant software05 EN Reset

1. Place the earbuds into the charging case and make sure they are being charged.

2. Press and hold the button on both earbuds for 8 seconds until the LED indicators

on earbuds ash red for 3 times. All the memory data will be cleared.

Specifications Specications are subject to change without notice. Input 5V 2.5A Rated output power 5 mW (@1% THD) Battery capacity 85 mA x 2 (earbuds); 2600 mA (charging case) Charging time 1.5 hours Playtime (varies by volume level and content) 8 hours (Total 100 hours with the charging case) Driver size 8 mm x 2 Frequency response 20 Hz - 20 kHz Impedance 16 Ω Waterproof level IPX5 Bluetooth version V 5.0 Bluetooth range 10 m / 33 ftCS 06 Nabíjení