Flowclear 58390 - Pump BESTWAY - Free user manual and instructions

Brand	Bestway
Model	Flowclear 58390
Product type	Above-ground pool filter pump
Usage	Only for temporary pools, not for in-ground pools
Power supply	220-240 V, 50 Hz, plug with ground protected by ground fault circuit interrupter (GFCI)
Motor power	Thermally protected motor, estimated power 250-350 W
Filter type	Replaceable filter cartridge
Cartridge replacement frequency	Every 2 weeks for optimal performance
Base dimensions	Width 390 mm, Depth 250 mm, Mounting hole spacing 163 mm
Minimum base weight for fixation	18 kg to prevent tipping
Safety protection	Class I, class A differential circuit breaker, grounding mandatory
Safety distance from outlets	At least 1.8 m from electrical outlets
Safety distance from water	No portable device within 1.5 m of the pool
Storage temperature	Between 10°C and 38°C, in a dry place
Routine maintenance	Regular cleaning of cartridge, disconnect power before maintenance
Installation	On a flat, solid surface, at the same level as the pool base
Usage precautions	Never run dry; ensure suction openings are not obstructed
Warranty	Check bestwaycorp.com for terms
Customer service	Online support at bestwaycorp.com/support

Frequently Asked Questions - Flowclear 58390 BESTWAY

Where to install the Flowclear 58390 filter pump?

Place the pump on a solid, flat surface, at the same level as the pool base. Keep it at least 1.8 m away from any electrical outlet and avoid areas where water can accumulate.

Can I use the pump with people in the pool?

No, it's dangerous. Never operate the pump when people are in the pool due to risk of electrocution.

How to safely connect the pump?

Plug the pump only into a grounded outlet protected by a class A ground fault circuit interrupter (GFCI). Do not use an extension cord and do not remove the grounding pin.

How often should I replace the filter cartridge?

For optimal performance and hygiene, replace the filter cartridge every two weeks.

What to do if the pump does not work?

Check that the pump is plugged in and the GFCI has not tripped. Make sure the suction openings are not obstructed and the pump is not dry. Consult the manual or visit bestwaycorp.com/support.

Can I use an extension cord?

No, using an extension cord is prohibited. Provide a properly located outlet within 1.8 m of the pump.

How to store the pump in winter?

Remove and discard the filter cartridge. Clean and dry the pump, hoses, and grilles thoroughly. Store it in a dry place between 10°C and 38°C. It is recommended to disassemble the pump if ambient temperature drops below 10°C.

Can the pump be used with chemicals?

No, never add chemicals into the filter pump. They must be added directly into the pool water.

How to secure the pump to the ground?

Use a wooden or concrete base of at least 18 kg. Drill two 9 mm holes spaced 163 mm apart, then secure the pump with the supplied M8 bolts and nuts.

What to do if the power cord is damaged?

To avoid danger, the damaged cord must be replaced by the manufacturer, its after-sales service, or a qualified person. Do not use the pump until the cord is repaired.

USER MANUAL Flowclear 58390 BESTWAY

bestwaycorp.com/support

OWNER'S MANUAL

bestwaycorp.com/support

Visit the Bestway YouTube channel YouTube

Visit www.bestwaycorp.com/support for help WE SUGGEST NOT TO RETURN THE PRODUCT TO THE STORE QUESTIONS? PROBLEMS? MISSING PARTS? For FAQ, Manuals, Videos Or Spare Parts, Please Visit bestwaycorp.com/support

OWNER'S MANUAL

58390/58647 Filter Pump

YouTube

Visit the Bestway YouTube channel

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS

Carefully read, understand, and follow all information in this user manual before installing and using the Filter Pump. These warnings, instructions, and safety guidelines address some common risks of water filtration systems, but they cannot cover all risks and dangers in all cases. Always use caution, common sense, and good judgment when enjoying any water activity. Retain this information for future use. In addition, the following information can be supplied depending on the Filter Pump type. Keep the instructions in a safe place. If instruction is missing, search it on the website www.bestwaycorp.com/support.

WARNING

• Thermally protected motor csa enclosure 3.
- For use with swimming pools only.
- CAUTION: To ensure continued protection against shock hazard, use only identical replacement parts when servicing.
- WARNING: Risk of electric shock. connect only to a grounding type receptacle protected by a ground-fault circuit interrupter (GFCI).
- CAUTION: This pump is for use with storable pools only - do not use with permanently-installed pools.
- CAUTION: Connect only to grounding type receptacle protected by a class a ground fault circuit interrupter.
- CAUTION: For continued protection against possible electric shock this unit is to be mounted to the base in accordance with the installation instructions.

TECHNICAL SAFETY INSTRUCTIONS

• Risk of electric shock, the pump cannot be using while people are inside the pool.
  • To reduce the risk of injury, do not permit children to use this product unless they are closely supervised at all times.
• To reduce the risk of electric shock the pool must be installed no closer than 6 feet (1.8 m) from any electrical outlet. Do not place portable appliances closer than 5 feet (1.5 m) from the pool.
• Do not bury cord. Locate cord to minimize abuse from lawn mowers, hedge trimmers, and other equipment.
• To reduce the risk of electric shock, replace damaged cord immediately. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• To reduce the risk of electric shock, do not use extension cord to connect unit to electric supply; provide a properly located outlet.
• This pump is for use with storable pools only. Do not use with permanently-installed pools. A storable pool is constructed so that it is capable of being readily disassembled for storage and reassembled to its original integrity. A permanently-installed pool is constructed in or on the ground or in a building such that it cannot be readily disassembled for storage.
• For continued protection against possible electric shock this unit is to be mounted to the base in accordance with the installation instructions.
• Using the pump with an unmatched electrical supply is dangerous and will result in catastrophic failure of pump.
• When working with electricity, turn the electrical power off at the circuit breaker and lock breaker door. Failure to do so will result in increased risk of shock, injury and possibly death.
• Do not remove the grounding prong or modify the plug in any way. Do not use adapter plugs. Consult a qualified electrician for any questions related to the validity of your plug's grounding.
• Handle the pump with care. Do not pull or carry the pump by the power cord. Never pull a plug from the outlet by yanking the power cord. Keep cord free from abrasions. Sharp objects, oil, moving parts, and heat should never be exposed to the filter pump.
  • Atmospheric conditions may affect the performance and life span of your filter pump. Unnecessary wear and tear that may occur during periods of cold, heat and exposure to sun. Whenever possible, shelter the pump from these conditions.
• Do not add chemicals in the filter pump.
• Assembly and disassembly by adults only.
  • Electric installations should follow national wiring rules, consult a qualified electrician with any questions.

SAVE THESE INSTRUCTIONS

ATTACHING A BASE

The filter pump must be vertically fixed on the ground or a base made of wood or concrete before use. There should be two holes 9mm in diameter on the base, the space between which should be 163mm. Put filter pump on the base and attach them together by fastening the bolts and nuts. All the base parts should weigh at least over 18kg to prevent the pump from accidentally falling.

2-M8 nut 2-M8 bolt

SETUP

CHECK LIST

To check the parts included in the box, consult the part list inside this manual. Verify that the equipment components represent the model that you had intended to purchase. In case of any damaged or missing parts at the time of purchase, visit our website bestwaycorp.com/support.

CHOOSE THE CORRECT LOCATION

Place the Filter Pump on a solid and level ground; it must be positioned on the same level as the base of the pool. If the Filter Pump is in an upper or lower position than the base of the pool, the performance and life span of the Filter Pump can be compromised. The pool and the Filter Pump have to be positioned in an area with adequate drainage and easy access for maintenance operations. Never place the Filter Pump in a area that may accumulate water.

INSTALLATION

• For the installation instructions, refer to the illustration steps inside the manual. Drawings are for illustration purposes only. May not reflect actual product. Not to scale.
• Bestway will not be responsible for any damage caused to the Filter Pump due to mishandling or failure to follow these instructions.
• It is imperative to check that the hydraulic connectors are not obstructed.
• Do not dry run the Filter Pump. Make sure both the pool's inlet and outlet valves are fully covered by water before operating the Filter Pump.

MAINTENANCE

• Make sure that the Filter Pump is unplugged before any maintenance.
• For the maintenance instructions, refer to illustration steps inside the manual. Drawings are for illustration purposes only. May not reflect actual product. Not to scale.
• To optimize the Filter Pump performance and for sanitary reasons, we suggest replacing the filter cartridge with a new one every two weeks.

STORAGE

• Remove all accessories; be sure that Filter Pump, hoses and debris screens are completely clean and dry before the storage. If all the parts are not completely dry, mold may result.
• Before storage, remove and dispose of the filter cartridge.
• We strongly recommend disassembling the Filter Pump when the environment temperature is below 50^ / 10^ .
• Store the Filter Pump in a dry place with a moderate temperature between 50^ / 10^ and 100^ / 38^ .

WARRANTY TERMS

For information concerning warranty terms, visit our website at: www.bestwaycorp.com.

CONDITIONS DE GARANTIE

CONDITIONS DE GARANTIE

Exploded view diagram of a blender with numbered parts for identification

	V1	V2	V3	V4
1	x1	x1	x1	x1
2	x1	x1	x1	x1
3	x1	x1	x1	x1
4	x1	x1	x1	x1
5	x1	x1	x1	x1
6	x2	x2	x3	x3
7	x2	x2	x2	x2
8	x0	x0	x2	x2
9	x0	x2	x0	x2
10	x0	x2	x4	x5
11	x0	x0	x1	x1
12	x0	x0	x2	x2
13	x0	x0	x2	x2
14	x0	x1	x0	x1
15	x0	x1	x0	x0

Diagram showing exploded view of a mechanical connector with numbered parts for identification.

V1 x2

Four grayscale 3D boxes with circular patterns, each containing a small icon (no text or symbols)

V2 x2

V3 x1 x2

V4 x3

1.1

Diagram showing a device with labeled parts A and B, including a magnified inset highlighting a hand holding a device.

1.2

A B A B

1.3

Simple line drawing of a mechanical component with no text or symbols

(1) (2) (3) (4)

graph LR
    A["(2) (3) (4)"] --> B["Heating Fan"]
    B --> C["1 min"]
    C --> D["Heating Plate"]
    D --> E["Heating Pump"]
    E --> F["Electric Upper Wiring"]

2.1 2.2

Diagram illustrating a mechanical assembly with labeled parts A and B, showing directional movement and component placement.

Diagram illustrating a medical or surgical procedure with labeled components A and B, showing mechanical assembly and magnified views of the device.

2.3

Simple line drawing of a mechanical component with tubing and connectors (no text or symbols)

(1) (2) (3) (4)

graph LR
    A["(2) (3) (4)"] --> B["Motor with fan"]
    B --> C["1 min"]
    C --> D["Motor with switch"]
    D --> E["Electrical circuit with power source"]

3.1

graph TD
    A["Car with valve"] --> B["Switch"]
    B --> C["Gear shift"]
    C --> D["Car with gear"]
    D --> E["Assembly"]
    style A fill:#f9f,stroke:#333
    style B fill:#ccf,stroke:#333
    style C fill:#cfc,stroke:#333
    style D fill:#fcc,stroke:#333
    style E fill:#cff,stroke:#333

3.2

A B B x4

3.3

graph LR
    A["Water jar with inlet"] --> B["(1) (2) (3) (4)"]
    B --> C["1 min"]
    C --> D["1 min"]
    D --> E["1 min"]
    E --> F["1 min"]

4.1 4.2

graph TD
    A["Valve with Pump"] --> B["Valve with Pump"]
    B --> C["Valve with Valve"]
    C --> D["Valve with Valve"]
    D --> E["Valve with Valve"]
    E --> F["Valve with Valve"]
    F --> G["Valve with Valve"]
    style A fill:#f9f,stroke:#333
    style B fill:#ccf,stroke:#333
    style C fill:#cfc,stroke:#333
    style D fill:#fcc,stroke:#333
    style E fill:#cff,stroke:#333
    style F fill:#ffc,stroke:#333

A B x5

4.3

graph LR
    A[" tank with coiled tube"] --> B[" (1) (2) (3) (4) "]
    B --> C[" 1 min "]
    C --> D[" (2) (3) (4) "]
    D --> E[" 1 min "]
    E --> F[" (2) (3) (4) "]
    F --> G[" 1 min "]
    G --> H[" (2) (3) (4) "]
    H --> I[" 1 min "]
    I --> J[" 1 min "]
    J --> K[" 1 min "]
    K --> L[" 1 min "]
    L --> M[" 1 min "]
    M --> N[" 1 min "]
    N --> O[" 1 min "]
    O --> P[" 1 min "]
    P --> Q[" 1 min "]
    Q --> R[" 1 min "]
    R --> S[" 1 min "]
    S --> T[" 1 min "]
    T --> U[" 1 min "]
    U --> V[" 1 min "]
    V --> W[" 1 min "]
    W --> X[" 1 min "]
    X --> Y[" 1 min "]
    Y --> Z[" 1 min "]

1.1

Diagram showing a pipe connection with labeled points A and B, including a plug symbol and directional arrow indicating flow or movement.

1.2

Diagram of a medical or laboratory device with labeled parts A and B, showing tubing connections and a magnified inset view.

1.3

graph LR
    A["Raw Material"] --> B["Rolling"]
    B --> C["Packing"]
    C --> D["Drinking"]
    D --> E["Product"]

1.4

graph LR
    A["Initial Setup"] --> B["(1) (2) (3) (4)"]
    B --> C["Step 1: Water Spray"]
    C --> D["Step 2: Round-over Rose"]
    D --> E["Step 3: Roundover Rose"]
    E --> F["Step 4: Roundover Rose"]
    F --> G["Final Discharge"]

2.1

Diagram of a cable or connector assembly with labeled parts A and B, showing wiring connections and a magnified inset showing a plug symbol.

2.2

Diagram illustrating a medical procedure with labeled steps A and B, showing mechanical components and a magnified view of the procedure.

2.3

graph LR
    A["Lathe with lid"] --> B["Rotation: 100%"]
    B --> C["Boiling: 50%"]
    C --> D["Cutting: 20%"]
    D --> E["Shipping: 10%"]
    E --> F["Boxing: 50%"]
    F --> G["Top: 50%"]

2.4

graph LR
    A["Initial Device"] --> B["Step (1) (2) (3) (4)"]
    B --> C["Step (1) (2) (3) (4) in a circular component"]
    C --> D["Step (1) (2) (3) (4) in a circular component with a valve, 1 min mark"]
    D --> E["Step (1) (2) (3) (4) in a circular component with a plug, 1 min mark"]
    E --> F["Step (1) (2) (3) (4) in a circular component with a plug, 1 min mark"]

3.1

Diagram showing a plug plug connected to a cable with labeled points A and B, and a magnified view of the plug plug symbol.

3.2

3.2 A B x4

3.3

graph LR
    A["Boiler with lid"] --> B["Coating with lid"]
    B --> C["Cut into container with lid"]
    C --> D["Close-up of lid with lid"]
    D --> E["Close-up of lid with lid"]
    E --> F["Close-up of lid with lid"]

3.4

graph LR
    A["Patient with laparoscopic implant"] --> B["Step (1) (2) (3)"]
    B --> C["Step (1) (2) (3)"]
    C --> D["Step (1) (2) (3)"]
    D --> E["Step (1) (2) (3)"]
    E --> F["Step (1) (2) (3)"]
    F --> G["Step (1) (2) (3)"]
    G --> H["Step (4) (4) + 1 min"]
    H --> I["Step (4) + 1 min"]

4.1

A B B

4.2

A B B x5

4.3

graph LR
    A["Lathe with lid"] --> B["Rotation: 100%"]
    B --> C["Boiling: 50%"]
    C --> D["Cutting: 50%"]
    D --> E["Shipping: 50%"]
    E --> F["Cutting: 50%"]
    F --> G["Shipping: 50%"]

4.4

Diagram illustrating fluid flow and mechanical components with labeled parts A and B, showing fluid movement and movement directions.

(1) (2) (3)

1 min

(4)

Diagram showing a plug with lightning bolt and upward arrow, connected to a battery pack with plug symbol

Bestway®

For support please visit us at:

bestwaycorp.com/support

©2022 Bestway Inflatables & Material Corp.

All rights reserved/Tous droits réservés/Todos los derechos reservados/Alle Rechte vorbehalten/Tutti i diritti riservati

Trademarks used in some countries under license from/

Manufactured, distributed and represented in the European Union by/

Distributed in Australia & New Zealand by Bestway Australia Pty Ltd, Unit 2/98-104 Carnarvon St Silverwater, NSW 2128, Australia

Tel: Australia: ([phone]; New Zealand: 0800 142 101

Distributed in United Kingdom by Bestway Corp UK Ltd. 8 Wentworth Road, Heathfield Industrial Estate, Newton Abbot, Devon, TQ12 6TL

Exported by/Exporté par/Exportado por/Exportiert von/Esportato da

Bestway (Hong Kong) International Ltd./Bestway Enterprise Company Limited

Suite 713, 7/Floor, East Wing, Tsim Sha Tsui Centre, 66 Mody Road, Kowloon, Hong Kong

www.bestwaycorp.com