secuENTRY easy 5602 - Smart Home Burg Wächter - Free user manual and instructions

Product Type	Electronic locking system (smart cylinder)
Available variants	secuENTRY easy PINCODE (PIN code) and secuENTRY easy FINGERPRINT (PIN code + fingerprint)
Power supply	4 AA batteries (2 for keypad, 2 for cylinder)
Maximum number of users	50 users (including up to 24 fingerprints for FINGERPRINT version)
Opening methods	6-digit PIN code, fingerprint (FINGERPRINT), BURG-WÄCHTER KeyApp (Bluetooth), mechanical emergency key
App compatibility	iOS 8.1.3+ (iPhone 4S and later) and Android 4.3/5.0+ (Samsung Galaxy S4 and later)
Compatible door	Door thickness up to 118 mm (59/59 mm at the center of the fixing screw)
Protection (keypad)	IP65 (PINCODE) / IP55 (FINGERPRINT)
Protection (cylinder)	IP65
Operating temperature	-15 °C to +50 °C (up to 95% humidity without condensation)
Lockout after errors	3 incorrect entries → 1 minute lockout, then 3 minutes for each additional error
Low battery indication	LED on cylinder flashes 5 times and on-screen message; 50 more openings possible
Display languages	12 adjustable languages
Maintenance	Clean with damp cloth; no alcohol-based or aggressive products; fingerprint sensor: damp cloth only
Installation	No drilling or cabling; fastening with grub screws and adapters
Package contents	Keypad, cylinder, exterior/interior knob, screws, Allen key, adhesive pads, covers, QR code

Frequently Asked Questions - secuENTRY easy 5602 Burg Wächter

How to change the administrator code?

Activate the keypad (⏻ button), press FUNC, select Menu / code change, then choose Administrator. Enter the old code, then the new 6-digit code (twice). Confirm with the Enter key.

How to add a new user with fingerprint?

Go to Administrator menu > Create user > Create: Fingerprint. Enter the administrator code, then slide your finger over the sensor several times (the number of passes is displayed). The fingerprint is saved under a user number.

What to do in case of low battery?

The screen displays 'Change keypad battery' or 'Change knob battery'. Replace the batteries (AA). After replacement, enter the opening code twice to reset the display. If you ignore the warning, you can still open 50 times, then only the administrator code works.

How to use the emergency key?

Unfold the emergency key, insert it into the slot on the exterior knob, turn it 90° clockwise while slightly turning the knob. The door opens after a full turn. To close, turn the key in the opposite direction.

How to connect the keypad to the BURG-WÄCHTER KeyApp?

Download the app from iOS or Android. Scan the provided QR code (or enter it manually). Follow the instructions for Bluetooth pairing. The cylinder must be powered.

How to reset the system?

Use the Administrator menu > Setup > Reorganization to delete all users. To reset only fingerprints, use the FP-Reset menu (FINGERPRINT version). Note: the administrator code is not reset by this procedure.

Maximum number of users and fingerprints?

Up to 50 users in total. In the FINGERPRINT version, up to 24 fingerprints can be stored. Each user can have a PIN code and/or a fingerprint.

What to do if the keypad stops responding?

Check the battery status (replace if necessary). If the problem persists, remove the batteries from the keypad and cylinder, wait 30 seconds, then reinsert them. If needed, perform a reconnection via the Setup > Connection menu.

How to clean the fingerprint sensor?

Use a damp cloth without cleaning agents. Avoid any alcohol-based, acetone, or aggressive solvents that could damage the sensor.

Can I use the cylinder without the keypad?

Yes, the cylinder can be operated via the BURG-WÄCHTER KeyApp (Bluetooth) or with the mechanical emergency key. The keypad is required for programming and user management.

USER MANUAL secuENTRY easy 5602 Burg Wächter

SN 10:0F:00:34 MAC 30:42:25:00:00:25 AES: 45:99:15:70:70:A0:A5:51: 87:D7:56:05:62:B5:F2:0E TYPE: 12

SN: 10:2D:00:3E MAC: 30:42:25:00:00:60 AES: E1:25:F3:E2:DB:86:C0:70: F7:EA:04:93:17:2E:BF:9E ADM: 123456

1 Tastatur (SN; MAC; AES; Type)
2 Zylinder (SN; MAC; AES; ADM)

Diagram showing 13 labeled parts of a device with icons and labels, including a keypad, QR code, and screwdriver.

Funktionen

Diagram of a digital payment terminal with labeled buttons and display screen

Diagram showing labeled components of a mechanical or electrical component with numbered parts and directional arrows

Technical diagram of a mechanical component with labeled part 12 (no text or symbols beyond label)

Simple gray rectangular shape with a small black dot and number 13 at the bottom (no text or symbols on the shape itself)

8 9 10

Two black-and-white photos showing hands using a tool to adjust or install a door lock (no text or symbols visible)

Close-up of hands adjusting a door lock mechanism, showing lock and handle assembly (no text or symbols visible)

Two black-and-white photos showing hands installing or adjusting a door lock and keyhole (no text or symbols visible)

Hand holding a small electronic device with white connectors (no visible text or symbols)

Black plastic mechanical component with cutouts and mounting holes (no text or symbols visible)

Close-up of a black electronic device with a display and control panel (no visible text or symbols)

Batteriewechsel secuENTRY easy Tastatur

Close-up of a screwdriver inserted into a black plastic cover on a wall, no visible text or symbols

Black-and-white photo of a CD-ROM drive with a circular arrow indicating rotation (no visible text or symbols)

MADE IN DEPARTMENT VARTA VARTA

Black triangular mechanical component with stepped edges and a curved arrow indicating rotation (no text or symbols)

Close-up of a black plastic clip attached to a wall, with no visible text or symbols

Close-up of a hand holding a cylindrical mechanical component with a wire, no visible text or symbols

Close-up of a hand holding a black circular knob on a metallic door handle (no text or symbols visible)

Two views of a mechanical component with internal components, shown from top and side angles (no text or symbols visible)

Close-up of a hand using a screwdriver to press down a cylindrical mechanical component (no text or symbols visible)

Close-up of a black plastic object mounted on a wall, with a tool inserted (no visible text or symbols)

Stacked hard drive case with a curved arrow indicating rotation (no visible text or symbols)

Close-up of a screwdriver inserted into a black plastic component with visible internal components (no text or symbols)

Close-up of a black and white electronic device with a digital display and control panel (no visible text or symbols)

Activation of the keypad for the entry of the opening code.

B Enter key

Selection of a menu item.

c Function key

The function key provides for a variety of actions depending on the current status of the keypad. The display indicates, which function is active.

1) Access to the menu for programming

When the "Func:M" symbol is displayed, the menu can be reached by pressing the "Func" key. In the menu, the keys "1" and "2" can be used as a scroll function to navigate through its structure.

2) Deleting an entry action

When the "Func:C" symbol is displayed, the last entry can be cancelled by pressing the "FUNC" key.

3) Entry to previous programming level / Back

When you are in the menu, the symbol "Func:<" is displayed.

By pressing the "FUNC" key, you return into the menu structure on the next higher level.

D Battery indicator

■■■. Battery full Battery empty

The display indicates battery statuses of the cylinder unit and the keypad unit. The indication on the display concerns the batteries with the lowest status. In case a battery is empty, the display indicates as follows:

Replace battery in keypad or replace battery in knob.

When the battery has been replaced and then the opening code entered twice, the currently lowest battery status is displayed. When only a single battery set is replaced, the display can still indicate an "incomplete" status, despite the replacement. In case you do not replace the batteries in spite of the replacement indication, you will have to enter the valid opening code once more in order to open the door. At the same time, the inner knob LED flashes 5 x 5 times. You can still open the door in this way approx. 50 times. Then it can only be opened using the administrator code. Now the batteries must be replaced, otherwise the door cannot be opened any more.

E Fingerscan sensor

To open or register the particular finger.

Dear customer,

Thank you very much for your decision for the secuENTRY electronic lock system manufactured by BURG-WÄCHTER. This system has been developed and manufactured using the latest technical potential and satisfies high security requirements.

The electronic cylinder can be used easily without any drilling in any door prepared for profile cylinder up to a door thickness of 118 mm (59 / 59, measured at the central detent bolt), and is perfectly appropriate for new installation as well as for retrofitting.

Depending on the specific system, various opening media are available. With systems containing a keypad, user administration is additionally integrated. You can find out more on the following pages.

Remove the battery protection strip from the inner knob in order to energise the cylinder.

Important: Please read the entire User Manual before you start programming. We hope you enjoy your new locking system.

General information about secuENTRY easy

secuENTRY is available in two equipment configurations:

• secuENTRY easy PINCODE
• secuENTRY easy FINGERPRINT

In the set configurations secuENTRY easy PINCODE and secuENTRY easy FINGERPRINT, the keypad is already registered in the cylinder.

Administrator code / QR code

The QR Code is required for both the setup of opening options using the BURG-WÄCHTER KeyApp and for the subsequent attaching and registration of a keypad or a cylinder. In secuENTRY Pincode and secuENTRY Fingerprint, the administrator code is factory-set to 1-2-3-4-5-6 (please never forget to change it).

SN: 10:0F:00:34 MAC: 30:42:25:00:00:25 AES: 45:99:15:70:70:A0:A5:51; 87:D7:56:05:62:B5:F2:0E TYPE: 12 1

SN: 10:2D:00:3E MAC: 30:42:25:00:00:60 AES: E1:25:F3:E2:DB:86:C0:70: F7:EA:04:93:17:2E:BF:9E ADM: 123456

1 Keypad (SN; MAC; AES; Type)
2 Cylinder (SN; MAC; AES; ADM)

Attention! In case you lose your administrator code and / or your QR code, any reprogramming and any use of administrator functions becomes impossible. Please store it carefully!

Hint: The QR code can also be stored in an electronic form as a scanned file or a photograph on a protected data carrier.

Additional functions available using the optional secuENTRY easy Software, for example:

• User administration
• Assignment of authorisations
  • History functions

Power supply

• 2 x MIGNON LR6 AA ALKALINE for the keypad
• 2 x MIGNON LR6 AA ALKALINE for the cylinder

Optical signalling

Optical signalling in the form of a LED is incorporated in the knob on the inner side of the door. This LED informs you on the following:

• 1 x brief: cylinder coupled
  • 2 x brief: cylinder uncoupled
• 1 x brief, 1 x long, 2 sec pause, repeating: lock in programming mode
• 5 x briefly, 2 sec pause, repeating at 20 sec: battery in cylinder empty

Technical data

Blocking times After	3 × wrong code is entered 1 minute, then always 3 minutes
Display Adjustable to	12 languages
Permissible ambient conditions*	-15 °C/+50 °C/up to 93 %rel. air humidity (noncondensing)Allowed temperature range: -20 °C / +50 °CAs a result of extreme temperature changes, the display can react slowly or darken.
Keypad protection class	Protection class keypad PINCODE IP65Protection class keypad Fingerprint IP55
Transmitting power and frequency range:	Bluetooth Low EnergyMaximum Transmit Output Power 7,5dBmFrequency usage range 2,402GHz ... 2,483 GHz

* In case the temperature exceeds the specified range, a corresponding warning message is indicated on the display. Provide for appropriate corrective action!

Opening

secuENTRY can be operated, depending on the equipment configuration, using a 6 digit numerical code, the Burg-Wächter KeyApp or with fingerprints.

Opening with PIN code

• Press the Key
• Enter the 6 digit PIN code (factory-set to 1-2-3-4-5-6). The display indicates "Please use rotating knob!" and the LED integrated in the cylinder flashes once when the opening is successful.
• Turn the cylinder knob

Opening with Fingerprint

• Press the Key
• Move the registered finger from the top to the bottom centrally over the sensor. The display indicates "Please use rotating knob!" and the LED integrated in the cylinder flashes once when opening is successful.
• Turn the cylinder knob

Opening with BURG-WÄCHTER KeyApp

• Hold your smart device in front of the cylinder knob and press the opening key of the KeyApp.
• The LED integrated in the cylinder flashes once when opening is successful.
• Turn the cylinder knob.

BURG-WÄCHTER KeyApp

You can download the BURG-WÄCHTER KeyApp from the App Store or the Google Play Store. For this purpose, simply enter the search item "secuENTRY" or "KeyApp".

Compatible with Samsung Galaxy S4, S4 mini, S5 and S5 mini from Android 4.3 KitKat or 5.0 Lollipop, Apple iPhone 4S, 5, 5S, 6, 6P or newer, from IOS 8.1.3.

Please check under:

www.burg.biz/secuentry/description

whether other Smartphones are compatible with the app.

secuENTRY easy PINCODE

Generally

The electronic cylinder is operated by entering a PIN code. Additionally, the lock can also be operated using the BURG-WÄCHTER KeyApp.

Contents of delivery

1 QR code keypad
2 Keypad
3 Outer knob
4 Fixing materials 1 keypad
5 Fixing materials 2 keypad (adhesive pads)
6 Rubber shell

7 Tx (size 8)
8 Detent bolt
9 Allen key (size 3)
10 QR code cylinder
11 Cylinder
12 Wall mounting plate
13 Shield foil

Functions

• Total number of users: up to 50

secuENTRY easy FINGERPRINT

Generally

The electronic cylinder is operated using a scanned finger. Up to 24 fingers can be programmed using the keypad. The users are created separately (USER XXX_FP).

If a code and / or an transponder should be additionally assigned to a user, it is to be created separately. Additionally, the lock can also be operated using a PIN code, or the BURG-WÄCHTER KeyApp.

Contents of delivery

1 QR code keypad
2 Keypad
3 Outer knob
4 Fixing materials 1 keypad
5 Fixing materials 2 keypad (adhesive pads)
6 Rubber shell

7 Tx (size 8)
8 Detent bolt
9 Allen key (size 3)
10 QR code cylinder
11 Cylinder
^12 Wall mounting plate
13 Shield foil

Diagram of a digital payment terminal with labeled button and control buttons

4 5 6 7

Technical diagram of a mechanical component with labeled part 12 (no text or symbols beyond label)

Simple gray rectangular shape with a small black dot and number 13 at the bottom (no text or symbols on the shape itself)

8 9 10

Attention! The fingerprint sensor must not be cleaned with detergents. Please use a slightly moistened cloth for this purpose.

Functions

- Total number of users: up to 50, out of whom number of fingerprints: up to 24

Basic indication of menu functions

Structure of the menu

Code change menu

Sprache/Language menu

Administrator menu

Create user menu

Create: Code

Create: Fingerprint

Delete menu

Additional functions menu

Date adjustment not available in the standard version

Time adjustment not available in the standard version

Setup menu

Register

Reorganise

FP reset menu

Info menu

Description of the menu functions

The following text described the functions for the products secuENTRY easy Pincode and secuENTRY easy FINGERPRINT.

Code change menu

Changing the administrator code and the user codes

• Activate the keypad using the ⏻ key
• Then press FUNC
  The Code Change menu is displayed
• Confirm your selection using
• Now you can use the keys 1 or 2 to scroll until the administrator / user, whose user code should be changed, is displayed
• Confirm with
• Enter the code valid so far (existing code) and press
• Enter the new code and confirm it with
• Repeat your entry and confirm it again with←.
  "Code change accomplished" is displayed after a correct entry

Sprache / Language menu

Language setup

• Activate the keypad using the Key
• Then press FUNC, the Code Change menu is displayed
• Scroll using the 2 key till reaching the above menu item
• Confirm with
• Use the keys 1 or 2 to scroll until the required language is displayed
• Confirm with

Administrator menu

Various submenus are available under the Administrator menu

Submenu create User with Code

• Activate the keypad using the ⏻ key
• Then press FUNC, the Code Change menu is displayed
• Scroll using the 2 key till reaching the Administrator menu
• Confirm with ←. The "Create User" menu item appears
• Confirm with
• Scroll using the 2 key till reaching "Create User: Code"
• Confirm with
• Enter the administrator code in order to acquire the authorisation for programming
• The next free memory space is indicated (e. g. USER.003)
• Enter the 6 digit code and confirm it 2 × with
• "Data has been saved" is displayed

Submenu create User with Fingerprint

(This function is only active with secuENTRY easy Fingerprint)

• Activate the keypad using the key
• Then press FUNC, the Code Change menu is displayed
• Scroll using the 2 key till reaching the Administrator menu
• Confirm with ← The "Create User" menu item appears
• Confirm with
• Scroll using the 2 key till reaching the "Create User: Fingerprint" item
• Confirm with
• Enter the administrator code in order to acquire the authorisation for programming
• "Register finger" is displayed
• Move the finger to be registered several times centrally over the sensor (the number of moves is indicated on the display)
• "User_XXX_FP successfully registered" is displayed

Submenu Delete

Using this menu, you can delete a user.

• Activate the keypad using the Key
• Then press FUNC, the Code Change menu is displayed
• Scroll using the 2 key till reaching the Administrator menu
• Confirm with
• Scroll using the 2 key till reaching the "Delete" item
• Enter the administrator code in order to acquire the authorisation for programming
• Scroll till reaching the user or the identification medium (transponder) you wish to delete and confirm your selection 2 × with
• "Data has been deleted" is displayed

Time Functions submenu (Premium only)

This is intended for setting the time and date

Setting the time:

Not available as a standard function.

Setting the date:

Not available as a standard function.

Setup submenu

General system settings

Register

After a replacement of the cylinder or the keypad, the two units have to be newly aligned, so that they can resume communication.

Registration of a keypad

• Activate the keypad using the key
• Then press FUNC, the Code Change menu is displayed
• Scroll using the 1 or 2 keys till reaching the Administrator menu
• Confirm with
• Now scroll using the 1 or 2 keys until reaching the Admin. Setup menu
• Confirm with
• Enter the admin code of the unit to be registered
• "Data has been saved" is displayed after a successful registration

Attention! Make sure that no other powered secuENTRY unit is placed within a direct reach of the device when registering a new keypad or a new cylinder, as such unit could be mistakenly addressed instead of the intended one. When in doubt, disconnect such units from power before the registration (remove batteries).

Reorganise

The use of this function is recommended when several users have been deleted.

• Activate the keypad using the Key
• Then press FUNC, the Code Change menu is displayed
• Scroll using the 2 key till reaching the Administrator menu
• Confirm with
• Scroll using the 2 key until reaching the "Setup" menu item
• Confirm with
• The "Reorganise" menu item appears
• Confirm with
• Enter the administrator code in order to acquire the authorisation for programming
• "Reorganisation in progress" is displayed

Submenu FP Reset

(This function is only active with secuENTRY easy Fingerprint and with the secuENTRY KP FP keypad) All the stored fingerprints are deleted, however, the corresponding users are retained. Please select this menu and follow the instructions on the display in case of repeated error functions related to the use of fingerprints.

Info menu

The version and serial number of the system are displayed using this function. For security reasons, the complete serial number is indicated only in the administrator mode.

• Activate the keypad using the Ⓤkey
• Then press FUNC, the Code Change menu is displayed
• Scroll using the 2 key till reaching the Info menu
• Confirm with. The serial numbers of the keypad"(EA) and of the cylinder (AA) are displayed.

Remark: For security reasons, the serial number (AA) of the cylinder is not completely displayed before the entry of a valid administrator code.

Installation Instructions for secuENTRY easy cylinder

Please read these Installation Instructions carefully before the assembly and then store them at a safe place.

The cylinder has a special detent system, offering you a possibility of using the cylinder for doors with a thickness up to 118 mm (59 / 59 mm, measured at the central detent bolt). No prior adjustment is necessary.

Attention: Be careful to not bang the knob anywhere, as the knob can break in such case. The lock should not be greased or oiled

An incorporated locking screw in each knob is to fix the rotary knobs.

Attention: Never pull the inner knob completely from the shaft, as this might cause damage to the electronics! The locking screw, which ensures the detent on the shaft, may be loosened only lightly and it always remains in the plastic knob, providing protection against pulling it out.

Outer side Outer knob

Inner side Inner knob

So illu th cy th

Schematic illustration of the mounted cylinder including the two adapters

Cover Adapter 2 Adapter 1 Detent bolt Locking screw

for fixation onto the shaft

Remark

The base size of the cylinder is 30 mm per side. When delivered, the cylinder is completely collapsed (the smallest door thickness). Before you insert the cylinder into the door, you should adjust it to your door thickness.

When installing the cylinder, proceed as follows:

1 Take a rough measurement of the door thickness (incl. fittings)
2 Pull the outer knob from the shaft, move the inner knob over the detent system (spacing 2.85 mm) to the required dimension.

inner knob 30 mm adjustment range

Schematic illustration of setup of the inner knob ajustement

3 Depending on the door thickness, you can affix an appropriate adapter on the outer side, in order to improve the path for the emergency key.

The following combinations are possible:

Space detent bolt / fitting (mm) on the outer side	Adapter 1 Adapter 2
< 43 --
44-53X -
54-60XX

Tab. 1: Space detent bolt / mounting [mm] on the outer side and the required adapter.

M2 × 10 Adapter 1

2,9 × 16 Adapter 2

4 Move the secuENTRY easy cylinder from inside to outside through the mortise lock into the door and then tighten the detent bolt.

Hand holding a cylindrical tool inserted into a wall-mounted device (no text or symbols visible)

Close-up of a hand using a screwdriver to adjust or install a door lock (no text or symbols visible)

5 Shift the inner knob over the shaft until attaining the required dimension. Please make sure that the clearance between the rotary knob and the door mounting is at least 1 mm. Then fix the rotary knob using the hex key.

6 Before you fix the outer knob, please consider whether you wish to use the attached cover panel for the profile cylinder section. If so, remove the protective sheet and fix the cover panel onto the lock section.

Close-up of a hand adjusting a door lock mechanism, showing lock type and door opening (no text or symbols visible)

7 Shift the outer knob into the required position on the shaft and fix it with a clearance of at least 1 mm from the mounting using the hex!

Two black-and-white photos showing hands installing or adjusting a door lock and keyhole (no text or symbols visible)

8 The function test must be made with the door open.

secuENTRY easy keypad installation

The keypad is only included in secuENTRY easy Pincode and secuENTRY easy Fingerprint sets.

Attention! Please remember that the keypad should not be attached to the door itself, otherwise it would transmit shocks when the door is being shut. The membrane affixed to the keypad rear side should not be sealed with glue and / or any other substance under any circumstances! Exchange of air must also be possible after the installation!

• Determine the installation place for the keypad. For that purpose, enter the opening code (e.g. PIN code, fingerprint, ...) at the desired mounting place and check whether the lock opens.
• Place the keypad correspondingly.

You can then decide whether you want to glue the wall holder directly on the wall or whether you prefer having it screwed on. The slotted holes in the wall holder provide for an exact alignment.

If you decide for gluing the wall holder, please be sure to provide for clean surfaces free from fat, oil and silicon films and any other impurities. Remove completely the protective film from the included adhesive pads, attach all the pads on the wall holder and then press the whole firmly to the required position. When mounting in colder temperatures, please remember that the full adhesive force cannot be achieved before 72 hours in 20 °C, with warmth accelerating the process (e.g. in 65 °C, the full adhesive force will be achieved in one hour).

When gluing the holder plate on the colour sight protection film, the above described conditions relating to cleanliness of surfaces and firmness of the adhesive pad should be observed.

Hand holding a small electronic device with white connectors (no visible text or symbols)

Black plastic mechanical component with internal slots and mounting holes (no text or symbols visible)

To provide for a bubble-free application of the colour sight protection film, please proceed as follows:

• Pour some water with a couple of drops of dishwashing detergent into a glass, stir it cautiously free of foam, and then use it to moisture gently the surface, on which the film is to be applied.
• At an edge, pull off the white protective sheet from 1 cm of film and straighten it out. To change the position, lift this surface carefully and attach it again as required.
• Then swipe the adhesive film, e. g. with a plastic spatula, out from the contact surface in the direction of protective sheet still attached.

Attention! Do not use more liquid than absolutely necessary.

- Slide the keypad in from above until the locking peg of the mounting plate engages into the keypad housing. In this way, the keypad is protected against undesired removal.

- Perform a function test of the unit with the door open. For this purpose, enter repeatedly a valid opening code (e.g. PIN code, fingerprint, ...).

Close-up of a black and white electronic device with a display screen and control buttons (no visible text or symbols)

Battery replacement for the secuENTRY easy keypad

- Remove the housing cover on the bottom side by loosing the 2 screws (Tx 8).

Close-up of a screwdriver inserted into a black cap on a wall, no visible text or symbols

- Pull the battery compartment lid downwards until it disengages and replace the batteries.

Stacked hard drives with a circular arrow indicating rotation (no visible text or symbols)

When inserting the new batteries, be careful to observe the correct polarity as indicated on the housing.

Black plastic battery pack with VARTA branding, no visible text or symbols on body

- To close the battery compartment, first press the battery compartment lid close to the screw holes to make them slide into the recesses, then snap the bottom side into position by pressing on it.

Black triangular mechanical component with stepped edges and a curved arrow indicating rotation (no text or symbols)

- Fasten the battery compartment lid with screws

Close-up of a black plastic clip attached to a wall, with no visible text or symbols

Attention! Make sure that no moisture enters the keypad when replacing the battery.

Cleaning instruction secuENTRY easy keypad

The surface finish of the keypad prevents adherence of impurities. Dust or dirt can be removed from the surfaces using a damp cloth.

No alcohol-based detergents (spirit, SIDOLIN® etc.) or aggressive detergents (acetone etc.) may be used, as they can damage the surface or the sensor.

Replacement of batteries – knob (inner side)

1 Using the attached hex key, loose the top locking screw on the cylinder cover. It can be turned out only up to the opening of the cover and will not fall out.

2 Open the cover

Close-up of a hand holding a metallic cylindrical component with a wire, no visible text or symbols

Close-up of a hand holding a black circular knob on a white door handle (no text or symbols visible)

3 Replace the batteries. Make sure the batteries are inserted with the correct polarity, indicated at the marked point on the housing.

4 Replace the cover.

Two views of a mechanical component with internal components, shown from top and side angles (no text or symbols visible)

Emergency key function (outer side)

Using the mechanical emergency key, you can provide access in case of failure of the system.

1 Swing the emergency key open and then insert it into the indicted slot in the cover panel.

Close-up of a hand using a screwdriver to press down a cylindrical mechanical component (no text or symbols visible)

2 Turn the key 90° clockwise. If required, move the outer knob slightly to the right and left in order to release the mechanism.
3 Turn the outer knob. The lock opens when fully turned at the latest.

Turn the key to its initial position and take it out. To close the emergency lock, the knob shall be turned twice fully in both directions.

Dismantling of secuENTRY easy keypad from wall holder

- Remove the housing cover on the bottom side by loosening the 2 screws (Tx 8).

Close-up of a screwdriver inserted into a black plastic cover on a wall (no text or symbols visible)

- Pull the battery compartment lid downwards until it disengages and replace the batteries.

Stacked hard drive case with visible internal components and a curved arrow indicating rotation (no text or symbols)

- Press the latch using a narrow tool (e. g. flat-bladed screwdriver) downwards and slide the keypad upwards.

Close-up of a screwdriver inserted into a black plastic electrical socket (no visible text or symbols)

Close-up of a black and white electronic device with a button and display (no visible text or symbols)

Interference from Bluetooth devices

Bluetooth devices use the same frequency band (2.4 GHz) as WiFi devices. This can cause interference leading to errors or even to communication failure. In such case, any devices not required should be kept disconnected from power.

Warranty

In order to be able to provide you with perfectly flawless and high quality products and an optimal support when you need servicing or repair, we need you to present faulty or defective devices to your vendor together with a valid administrator code and the QR code(s), with the original purchase document attached.

When you return a device component based on your right of withdrawal from the purchase agreement, such component shall be adjusted to factory settings and the seal on the cylinder and on the knob shall be intact. In case of noncompliance with this, the warranty becomes invalid.

Disposal

Dear customer,

Please help us avoid unnecessary waste.

Should you intend to dispose of this device at any time, please remember that many components of this device contain valuable materials, which can be recycled.

Please be aware that electrical and electronic equipment and batteries shall not be disposed of as household waste, but rather collected separately. Please obtain information on the collecting points for electrical waste from the responsible authority of you municipality.

BURG-WÄCHTER KG hereby declares that this device complies with Directive 2014/53/EU, (RED) 2014/30/EU, (EMC) and 2011/65/EU (RoHS). The full text of the EU Declaration of Conformity can be found on the following website

www.burg.biz

Illustration

SN:	10:0F:00:34
MAC:	30:42:25:00:00:25
AES:	45:99:15:70:70:A0:A5:51:87:D7:56:05:62:B5:F2:0E
TYPE:	12

SN:	10:2D:00:3E
MAC:	30:42:25:00:00:60
AES:	E1:25:F3:E2:DB:86:C0:70:F7:EA:04:93:17:2E:BF:9E
ADM:	123456

1 Clavier (SN; MAC; AES; Type)
2 Cylindre (SN; MAC; AES; ADM)

Diagram showing 13 labeled parts of a device with icons and labels, including a QR code, buttons, and a screwdriver.

Fonctionnalités

Hand holding a metallic tool inserted into a wall-mounted lock (no text or symbols visible)

Close-up of a hand using a screwdriver to adjust or install a door lock (no text or symbols visible)

Close-up of a hand adjusting a door lock mechanism, showing the lock being locked in a metal door (no text or symbols visible)

Two black-and-white photos showing hands installing or adjusting a door lock and keyhole (no text or symbols visible)

Hand holding a small electronic device with white connectors (no visible text or symbols)

Black plastic mechanical component with internal slots and mounting holes (no text or symbols visible)

Close-up of a black electronic device with a display and control panel (no visible text or symbols)

Close-up of a screwdriver inserted into a black plastic cover on a wall (no text or symbols visible)

Black-and-white photo of a CD-ROM drive with a circular arrow indicating rotation (no visible text or symbols)

Black triangular mechanical component with stepped edges and a curved arrow indicating rotation (no text or symbols)

Close-up of a black plastic clip attached to a wall, with no visible text or symbols

Close-up of a hand holding a cylindrical mechanical component with a wire, no visible text or symbols

Close-up of a hand holding a black circular knob on a metallic door handle (no text or symbols visible)

Two views of a mechanical component with internal components, shown from top and side angles (no text or symbols visible)

Close-up of a hand holding a cylindrical object with an arrow pointing to it, against a plain background (no text or symbols visible)

Close-up of a black cap with a screwdriver inserted, mounted on a wall (no visible text or symbols)

Close-up of a CD-ROM drive with a circular arrow indicating rotation (no visible text or symbols)

Close-up of a black plastic electronic device with a screwdriver inserted, showing internal components (no visible text or symbols)

Black and white photo of a handheld electronic device with a display screen and control buttons (no visible text or symbols)

SN:	10:DF:00:34
MAC:	30:42:25:00:00:25
AES:	45:99:15:70:70:A0:A5:51:87:D7:56:05:62:B5:F2:0E
TYPE:	12

SN:	10:2D:00:3E
MAC:	30:42:25:00:00:60
AES:	E1:25:F3:E2:DB:86:C0:70:F7:EA:04:93:17:2E:BF:9E
ADM:	123456

1 Keypad (SN; MAC; AES; Type)
2 Keypad (SN; MAC; AES; ADM)

Diagram showing various electronic components with numbered labels and icons, including a keypad, QR code, and screwdriver.

Functions

Diagram showing 13 labeled parts of a device with icons and labels, including a keypad, QR code, and screwdriver.

Two black-and-white photos showing hands using a tool to adjust or install a door lock (no text or symbols visible)

Close-up of a hand adjusting a door lock mechanism, showing the lock being locked (no text or symbols visible)

Two black-and-white photos showing hands installing or adjusting a door lock and keyhole (no text or symbols visible)

Hand holding a small electronic device with white connectors (no visible text or symbols)

Black plastic mechanical component with cutouts and internal slots (no text or symbols visible)

Close-up of a black electronic device with a display screen and control buttons (no visible text or symbols)

Close-up of a black plastic object mounted on a wall, with a tool inserted (no visible text or symbols)

Black-and-white photo of a CD-ROM drive with a circular arrow indicating rotation (no visible text or symbols)

MODE IN DEPARTMENT VARTA VARTA

Black triangular mechanical component with stepped edges and a curved arrow indicating rotation (no text or symbols)

Close-up of a black plastic clip attached to a wall, with no visible text or symbols

Close-up of a hand holding a metallic cylindrical component with a wire, no visible text or symbols

Close-up of a hand holding a black circular knob on a white door handle (no text or symbols visible)

Two views of a mechanical component with internal components, shown from top and side angles (no text or symbols visible)

Close-up of a hand using a screwdriver to press down a cylindrical mechanical component (no text or symbols visible)

Close-up of a black plastic component mounted on a wall, with a tool inserted (no visible text or symbols)

Close-up of a black hard drive with a circular arrow indicating rotation (no visible text or symbols)

Close-up of a black plastic electrical socket with a screwdriver inserted, showing internal components (no text or symbols visible)

Black and white photo of a handheld electronic device with a display screen (no visible text or symbols)