RS 110 - Lock Burg Wächter - Free user manual and instructions

Product Type	Mechanical Combination Lock
Brand	Burg Wächter
Model	RS 110
Number of Dials	4
Factory Combination	0-0-0-0
Code Customization	Yes, via setting pin
Locking	By scrambling the dials after closing
Unlocking	Aligning the dials to the combination
Main Material	Steel
Approximate Dimensions	100 x 50 x 30 mm
Approximate Weight	200 g
Power Supply	None (mechanical)
Main Functions	Combination locking, customizable code, security scrambling
Cleaning	Damp cloth, avoid abrasive products
Lubrication	Mechanism with appropriate lubricant
Mounting	4 fixing screws, drilling pilot holes
Security	Changeable code, mandatory scrambling, no opening without code
Country of Origin	Germany

Frequently Asked Questions - RS 110 Burg Wächter

How do I change the code of my RS 110 lock?

To change the code, press the small silver pin at the end of the locking bolt (fig. 1). While holding the pin down, turn the 4 dials to set the new combination. Make sure the numbers are centered and engaged. Release the pin. The new code is saved.

What if I forgot my custom code?

If the new code is lost, it is impossible to open the lock. No reset solution is provided. It is strongly recommended to write down the code in a safe place.

How do I open the lock with the factory code?

The factory code is 0-0-0-0. Turn each dial to align the 0 with the center line. By turning the dials toward the sliding bolt, they automatically stop at zero. The bolt then unlocks.

How do I lock the lock correctly?

After closing the lock, it is imperative to scramble the combination by turning the 4 dials to random numbers. Without scrambling, the lock may be opened inadvertently.

Should I lubricate the lock?

Yes, it is recommended to treat the locking mechanism with an appropriate lubricant, especially if the lock becomes hard to operate. Avoid greasy lubricants that may attract dust.

How do I clean the RS 110 lock?

Use a damp cloth to clean the exterior. Do not use abrasive products or solvents that could damage the finish.

What tools are needed for mounting?

You will need a drill for pilot holes, a screwdriver suitable for the provided security screws, and possibly wall plugs for a solid fixing depending on the surface.

Can the lock be mounted on an interior door?

Yes, the RS 110 lock can be mounted on any type of door or drawer. The mounting guide indicates to drill pilot holes for the screws and to check the proper operation of the sliding bolt.

Is the lock weather-resistant?

The instructions do not mention outdoor use. It is likely that the lock is designed for indoor use. For outdoor use, protection against moisture is recommended.

Can I order spare parts?

The instructions do not indicate available spare parts. In case of malfunction, contact Burg Wächter customer service to find out if repairs are possible.

USER MANUAL RS 110 Burg Wächter

Pure mechanical component diagram without any text, numbers, or symbols

Abb. 1

Bedienung

Öffnen

To open, rotate all 4 dials to the pre-set combination along the centre line. The pre-set factory combination is 0-0-0-0.

The dials stop automatically at 0 if they are turned towards the side bolt. This fuctionality is helpful when the lock is opened in poor light, as the clicks of the turning dials can be counted.

Set your own combination

On the end of the locking bolt, fully depress the small silver pin. (Fig. 1) Whilst holding in the pin, rotate the 4 dials to your chosen secret combi nation. Ensure the numbers are positioned centrally and have clicked into position. Release the pin to the original position. Memorise and record the new combi nation for future reference.

The new code is now set.

Note: If the new code is lost, the lock cannot be opened any more.

Lock

The combination must be scrambled by rotating the 4 dials. The slide bolt can be latched both while open and closed.

Fitting instructions

Note: Regular screws can be used to temporally fix the locking bolt before finally fixing using the security screws supplied. It is important to drill a small pilot hole for the screws as they cannot be unscrewed once used.

1 Hold the slide bolt in the required position and check the slide bolt and the gate / door will function correctly. Once positioned correctly, mark the location of the 4 screw holes.
2 The slide bolt should be mounted using all the 4 corner fixing holes on the back plate. Drill a small pilot hole for the screws. Screws should be tight without distorting the back plate.

Depending on the material of the installation place it may make sense to drill small guiding holes to facilitate fitting. Drills should be chosen according to material and screw diameter. It may be advantageous to use dowels.

3 Hold the counterpiece in the required position and check the slide bolt and the gate / door will open and close correctly. Mark the location of the 2 screw holes and drill small pilot holes. Fix in position using the screws.

Maintenance: It is recommended the dials are rotated weekly to keep them moving freely. Please clean the lock with a wet cloth if required, and use a common lubricant for the locking mechanism.

Mistakes and changes reserved.

Opération

Ouvrir